We don't need a temporary variable just to store the return value which
gets return in the next statement.
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
Signed-off-by: Kent Yoder <key@linux.vnet.ibm.com>
Err is never read before it is assigned again -> remove the dead
assigment.
Found with clang static analyzer
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
Signed-off-by: Kent Yoder <key@linux.vnet.ibm.com>
With the HOTPLUG changes 3.8 this attribute is going away.
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
Signed-off-by: Kent Yoder <key@linux.vnet.ibm.com>
We don't need to call memcpy for one byte, but assign it directly.
And to make the offset clearer we use the array syntax on the subsequent
call to memset to make the relationship clearer.
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
Signed-off-by: Kent Yoder <key@linux.vnet.ibm.com>
The TIS specification (pg 47) says the valid bit must be set, but
the TPM will not set it until it has completed its internal startup.
The driver checks that the valid bit is set during request_locality,
but it issues a TPM_ACCESS_REQUEST_USE without validating the
valid bit is set.
Some TPMs will ignore the TPM_ACCESS_REQUEST_USE, until valid is
set which causes the request_locality to timeout, which breaks the
driver attach.
Wait one timeout unit for valid to assert. If valid does not assert
then assume -ENODEV.
Seen on embedded with a:
1.2 TPM (device-id 0x3204, rev-id 64)
Signed-off-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Signed-off-by: Kent Yoder <key@linux.vnet.ibm.com>
Support cancellation of TPM commands when driver is used in interrupt
mode.
Signed-off-by: Stefan Berger <stefanb@linux.vnet.ibm.com>
Signed-off-by: Kent Yoder <key@linux.vnet.ibm.com>
On one of my machines the cancellation of TPM commands does not work.
The reason is that by writing into sysfs 'cancel' the tpm_tis_ready
call causes the status flag TPM_STS_VALID to be set in the statusregister.
However, the TIS driver seems to wait for TPM_STS_COMMAND_READY.
Once a 2nd time sysfs 'cancel' is written to, the TPM_STS_COMMAND_READY flag
also gets set, resulting in TPM_STS_VALID|TPM_STS_COMMAND_READY to be
read from the status register.
This patch now converts req_canceled into a function to enable more complex
comparisons against possible cancellation status codes.
Signed-off-by: Stefan Berger <stefanb@linux.vnet.ibm.com>
Signed-off-by: Kent Yoder <key@linux.vnet.ibm.com>
We've been testing an alternative TPM for our embedded products and
found random kernel boot failures due to time outs after the continue
self test command.
This was happening randomly, and has been *very* hard to track down, but
it
looks like with this chip there is some kind of race with the
tpm_tis_status()
check of TPM_STS_COMMAND_READY. If things get there 'too fast' then
it sees the chip is ready, or tpm_tis_ready() works. Otherwise it takes
somewhere over 400ms before the chip will return TPM_STS_COMMAND_READY.
Adding some delay after tpm_continue_selftest() makes things reliably
hit the failure path, otherwise it is a crapshot.
The spec says it should be returning TPM_WARN_DOING_SELFTEST, not
holding
off on ready..
Boot log during this event looks like this:
tpm_tis 70030000.tpm_tis: 1.2 TPM (device-id 0x3204, rev-id 64)
tpm_tis 70030000.tpm_tis: Issuing TPM_STARTUP
tpm_tis 70030000.tpm_tis: tpm_transmit: tpm_send: error -62
tpm_tis 70030000.tpm_tis: [Hardware Error]: TPM command timed out during
continue self test
tpm_tis 70030000.tpm_tis: tpm_transmit: tpm_send: error -62
tpm_tis 70030000.tpm_tis: [Hardware Error]: TPM command timed out during
continue self test
tpm_tis 70030000.tpm_tis: tpm_transmit: tpm_send: error -62
tpm_tis 70030000.tpm_tis: [Hardware Error]: TPM command timed out during
continue self test
tpm_tis 70030000.tpm_tis: tpm_transmit: tpm_send: error -62
tpm_tis 70030000.tpm_tis: [Hardware Error]: TPM command timed out during
continue self test
The other TPM vendor we use doesn't show this wonky behaviour:
tpm_tis 70030000.tpm_tis: 1.2 TPM (device-id 0xFE, rev-id 70)
Signed-off-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Signed-off-by: Kent Yoder <key@linux.vnet.ibm.com>
When no i2c bus exists, user-space can cause an oops by triggering a
device probe through a message sent to an i2c "new_device" sysfs entry.
Adding a check for a NULL i2c client structure in the probe function
closes the hole.
This patch also fixes accessing the NULL client struct in the print
function call reporting the error.
Reported-by: Peter Hüwe <PeterHuewe@gmx.de>
Signed-off-by: Kent Yoder <key@linux.vnet.ibm.com>
This patch converts the suspend and resume functions for
tpm_i2c_stm_st33 to the new dev_pm_ops.
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
Signed-off-by: Kent Yoder <key@linux.vnet.ibm.com>
* STMicroelectronics version 1.2.0, Copyright (C) 2010
* STMicroelectronics comes with ABSOLUTELY NO WARRANTY.
* This is free software, and you are welcome to redistribute it
* under certain conditions.
This is the driver for TPM chip from ST Microelectronics.
If you have a TPM security chip from STMicroelectronics working with
an I2C, in menuconfig or .config choose the tpm driver on
device --> tpm and activate the protocol of your choice before compiling
the kernel.
The driver will be accessible from within Linux.
Tested on linux x86/x64, beagleboard REV B & XM REV C and CHROMIUM OS
Signed-off-by: Mathias Leblanc <mathias.leblanc@st.com>
Signed-off-by: Kent Yoder <key@linux.vnet.ibm.com>
Store the i2c_client struct in the vendor private pointer. Get rid of
the unnecessary include/linux/i2c/ header. Moved include files into the
driver c file. Fix smatch warnings. Make use of module_i2c_driver().
Removed unused code from the tpm_stm_st33_i2c.h file. Fix return
variable signedness in tpm_stm_i2c_send() and tpm_st33_i2c_probe().
Signed-off-by: Kent Yoder <key@linux.vnet.ibm.com>
"data" was too generic a name for what's being used as a generic
private pointer by vendor-specific code. Rename it to "priv" and provide
a #define for users.
Signed-off-by: Kent Yoder <key@linux.vnet.ibm.com>
* STMicroelectronics version 1.2.0, Copyright (C) 2010
* STMicroelectronics comes with ABSOLUTELY NO WARRANTY.
* This is free software, and you are welcome to redistribute it
* under certain conditions.
This is the driver for TPM chip from ST Microelectronics.
If you have a TPM security chip from STMicroelectronics working with
an I2C, in menuconfig or .config choose the tpm driver on
device --> tpm and activate the protocol of your choice before compiling
the kernel.
The driver will be accessible from within Linux.
Tested on linux x86/x64 on kernel 3.x
Signed-off-by: Mathias Leblanc <mathias.leblanc@st.com>
Signed-off-by: Kent Yoder <key@linux.vnet.ibm.com>
Bool initializations should use true and false. Bool tests don't need
comparisons. Based on contributions from Joe Perches, Rusty Russell
and Bruce W Allan.
The semantic patch that makes this output is available
in scripts/coccinelle/misc/boolinit.cocci.
More information about semantic patching is available at
http://coccinelle.lip6.fr/
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
Signed-off-by: Kent Yoder <key@linux.vnet.ibm.com>
This seems to be preferred these days.
Signed-off-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Reviewed-by: Peter Huewe <peterhuewe@gmx.de>
Signed-off-by: Kent Yoder <key@linux.vnet.ibm.com>
The TPM will respond to TPM_GET_CAP with TPM_ERR_INVALID_POSTINIT if
TPM_STARTUP has not been issued. Detect this and automatically
issue TPM_STARTUP.
This is for embedded applications where the kernel is the first thing
to touch the TPM.
Signed-off-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Tested-by: Peter Huewe <peter.huewe@infineon.com>
Reviewed-by: Peter Huewe <peter.huewe@infineon.com>
Signed-off-by: Kent Yoder <key@linux.vnet.ibm.com>
This patch changes the semantics of the duration calculation for an
ordinal, by masking out the higher bits of a tpm command, which specify
whether it's an TPM_PROTECTED_COMMAND, TPM_UNPROTECTED_COMMAND,
TPM_CONNECTION_COMMAND, TPM_CONNECTION_COMMAND, TPM_VENDOR_COMMAND.
(See TPM Main Spec Part 2 Section 17 for details).
For all TPM_PROTECTED and TPM_CONNECTION commands the results are
unchanged.
The TPM_UNPROTECTED commands are TSS commands and thus irrelevant as
they are not sent to the tpm.
For vendor commands the semantics change for ordinals 10 and 11 but
they were probably wrong anyway.
For everything else which has the ordinal set to 10 or 11 the semantics
change as it now uses TPM_UNDEFINED instead of TPM_SHORT which was
probably wrong anyway (but irrelevant as not defined by the standard).
This patch also gets rid of the (false positive) smatch warning:
drivers/char/tpm/tpm.c:360 tpm_calc_ordinal_duration() error: buffer
overflow 'tpm_protected_ordinal_duration' 12 <= 243
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
Signed-off-by: Kent Yoder <key@linux.vnet.ibm.com>
The entries in tpm_protected_ordinal_duration are exactly the same as
the first 12 in tpm_ordinal_duration, so we can simply remove this one,
and save some bytes.
This does not change the behavior of the driver.
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
Signed-off-by: Kent Yoder <key@linux.vnet.ibm.com>
Pull security subsystem updates from James Morris:
"A quiet cycle for the security subsystem with just a few maintenance
updates."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security:
Smack: create a sysfs mount point for smackfs
Smack: use select not depends in Kconfig
Yama: remove locking from delete path
Yama: add RCU to drop read locking
drivers/char/tpm: remove tasklet and cleanup
KEYS: Use keyring_alloc() to create special keyrings
KEYS: Reduce initial permissions on keys
KEYS: Make the session and process keyrings per-thread
seccomp: Make syscall skipping and nr changes more consistent
key: Fix resource leak
keys: Fix unreachable code
KEYS: Add payload preparsing opportunity prior to key instantiate or update
Here is the "big" char/misc driver patches for 3.8-rc1. I'm starting to
put random driver subsystems that I had previously sent you through the
driver-core tree in this tree, as it makes more sense to do so.
Nothing major here, the various __dev* removals, some mei driver
updates, and other random driver-specific things from the different
maintainers and developers.
Note, some MFD drivers got added through this tree, and they are also
coming in through the "real" MFD tree as well, due to some major
mis-communication between me and the different developers. If you have
any merge conflicts, take the ones from the MFD tree, not these ones,
sorry about that.
All of this has been in linux-next for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iEYEABECAAYFAlDHj7AACgkQMUfUDdst+ym7pQCgxhFDGQRJimG+Ddag+ghfLhQh
Ql0AoJsWVFvQjb7q1NO7OvOABaxjEJdu
=na5b
-----END PGP SIGNATURE-----
Merge tag 'char-misc-3.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull Char/Misc driver merge from Greg Kroah-Hartman:
"Here is the "big" char/misc driver patches for 3.8-rc1. I'm starting
to put random driver subsystems that I had previously sent you through
the driver-core tree in this tree, as it makes more sense to do so.
Nothing major here, the various __dev* removals, some mei driver
updates, and other random driver-specific things from the different
maintainers and developers.
Note, some MFD drivers got added through this tree, and they are also
coming in through the "real" MFD tree as well, due to some major
mis-communication between me and the different developers. If you
have any merge conflicts, take the ones from the MFD tree, not these
ones, sorry about that.
All of this has been in linux-next for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>"
Fix up trivial conflict in drivers/mmc/host/Kconfig due to new drivers
having been added (both at the end, as usual..)
* tag 'char-misc-3.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (84 commits)
MAINTAINERS: remove drivers/staging/hv/
misc/st_kim: Free resources in the error path of probe()
drivers/char: for hpet, add count checking, and ~0UL instead of -1
w1-gpio: Simplify & get rid of defines
w1-gpio: Pinctrl-fy
extcon: remove use of __devexit_p
extcon: remove use of __devinit
extcon: remove use of __devexit
drivers: uio: Only allocate new private data when probing device tree node
drivers: uio_dmem_genirq: Allow partial success when opening device
drivers: uio_dmem_genirq: Don't use DMA_ERROR_CODE to indicate unmapped regions
drivers: uio_dmem_genirq: Don't mix address spaces for dynamic region vaddr
uio: remove use of __devexit
uio: remove use of __devinitdata
uio: remove use of __devinit
uio: remove use of __devexit_p
char: remove use of __devexit
char: remove use of __devinitconst
char: remove use of __devinitdata
char: remove use of __devinit
...
CONFIG_HOTPLUG is going away as an option so __devexit_p is no longer
needed.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Cc: Rajiv Andrade <mail@srajiv.net>
Cc: Marcel Selhorst <tpmdd@selhorst.net>
Cc: Sirrix AG <tpmdd@sirrix.com>
Acked-by: Kent Yoder <key@linux.vnet.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
CONFIG_HOTPLUG is going away as an option so __devinit is no longer
needed.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Cc: Rajiv Andrade <mail@srajiv.net>
Cc: Marcel Selhorst <tpmdd@selhorst.net>
Cc: Sirrix AG <tpmdd@sirrix.com>
Acked-by: Kent Yoder <key@linux.vnet.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
CONFIG_HOTPLUG is going away as an option so __devinitdata is no
longer needed.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Cc: David Airlie <airlied@linux.ie>
Cc: Kent Yoder <key@linux.vnet.ibm.com>
Cc: Rajiv Andrade <mail@srajiv.net>
Cc: Marcel Selhorst <tpmdd@selhorst.net>
Cc: Sirrix AG <tpmdd@sirrix.com>
Cc: openipmi-developer@lists.sourceforge.net
Cc: tpmdd-devel@lists.sourceforge.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch removed the tasklet and moved the wait queue into the
private structure. It also cleaned up the response CRQ path.
Signed-off-by: Ashley Lai <adlai@us.ibm.com>
Signed-off-by: Kent Yoder <key@linux.vnet.ibm.com>
tpm_write calls tpm_transmit without checking the return value and
assigns the return value unconditionally to chip->pending_data, even if
it's an error value.
This causes three bugs.
So if we write to /dev/tpm0 with a tpm_param_size bigger than
TPM_BUFSIZE=0x1000 (e.g. 0x100a)
and a bufsize also bigger than TPM_BUFSIZE (e.g. 0x100a)
tpm_transmit returns -E2BIG which is assigned to chip->pending_data as
-7, but tpm_write returns that TPM_BUFSIZE bytes have been successfully
been written to the TPM, altough this is not true (bug #1).
As we did write more than than TPM_BUFSIZE bytes but tpm_write reports
that only TPM_BUFSIZE bytes have been written the vfs tries to write
the remaining bytes (in this case 10 bytes) to the tpm device driver via
tpm_write which then blocks at
/* cannot perform a write until the read has cleared
either via tpm_read or a user_read_timer timeout */
while (atomic_read(&chip->data_pending) != 0)
msleep(TPM_TIMEOUT);
for 60 seconds, since data_pending is -7 and nobody is able to
read it (since tpm_read luckily checks if data_pending is greater than
0) (#bug 2).
After that the remaining bytes are written to the TPM which are
interpreted by the tpm as a normal command. (bug #3)
So if the last bytes of the command stream happen to be a e.g.
tpm_force_clear this gets accidentally sent to the TPM.
This patch fixes all three bugs, by propagating the error code of
tpm_write and returning -E2BIG if the input buffer is too big,
since the response from the tpm for a truncated value is bogus anyway.
Moreover it returns -EBUSY to userspace if there is a response ready to be
read.
Signed-off-by: Peter Huewe <peter.huewe@infineon.com>
Signed-off-by: Kent Yoder <key@linux.vnet.ibm.com>
This patch try to fix the S3 regression https://lkml.org/lkml/2012/10/5/433,
which includes below line:
[ 1554.684638] sysfs: cannot create duplicate filename '/devices/pnp0/00:0c/ppi'
The root cause is that ppi sysfs teardown code is MIA, so while S3 resume,
the ppi kobject will be created again upon existing one.
To make the tear down code simple, change the ppi subfolder creation from
using kobject_create_and_add to just using a named ppi attribute_group. Then
ppi sysfs teardown could be done with a simple sysfs_remove_group call.
Adjusted the name & return type for ppi sysfs init function.
Reported-by: Ben Guthro <ben@guthro.net>
Signed-off-by: Gang Wei <gang.wei@intel.com>
Signed-off-by: Kent Yoder <key@linux.vnet.ibm.com>
Pull security subsystem updates from James Morris:
"Highlights:
- Integrity: add local fs integrity verification to detect offline
attacks
- Integrity: add digital signature verification
- Simple stacking of Yama with other LSMs (per LSS discussions)
- IBM vTPM support on ppc64
- Add new driver for Infineon I2C TIS TPM
- Smack: add rule revocation for subject labels"
Fixed conflicts with the user namespace support in kernel/auditsc.c and
security/integrity/ima/ima_policy.c.
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security: (39 commits)
Documentation: Update git repository URL for Smack userland tools
ima: change flags container data type
Smack: setprocattr memory leak fix
Smack: implement revoking all rules for a subject label
Smack: remove task_wait() hook.
ima: audit log hashes
ima: generic IMA action flag handling
ima: rename ima_must_appraise_or_measure
audit: export audit_log_task_info
tpm: fix tpm_acpi sparse warning on different address spaces
samples/seccomp: fix 31 bit build on s390
ima: digital signature verification support
ima: add support for different security.ima data types
ima: add ima_inode_setxattr/removexattr function and calls
ima: add inode_post_setattr call
ima: replace iint spinblock with rwlock/read_lock
ima: allocating iint improvements
ima: add appraise action keywords and default rules
ima: integrity appraisal extension
vfs: move ima_file_free before releasing the file
...
Pull workqueue changes from Tejun Heo:
"This is workqueue updates for v3.7-rc1. A lot of activities this
round including considerable API and behavior cleanups.
* delayed_work combines a timer and a work item. The handling of the
timer part has always been a bit clunky leading to confusing
cancelation API with weird corner-case behaviors. delayed_work is
updated to use new IRQ safe timer and cancelation now works as
expected.
* Another deficiency of delayed_work was lack of the counterpart of
mod_timer() which led to cancel+queue combinations or open-coded
timer+work usages. mod_delayed_work[_on]() are added.
These two delayed_work changes make delayed_work provide interface
and behave like timer which is executed with process context.
* A work item could be executed concurrently on multiple CPUs, which
is rather unintuitive and made flush_work() behavior confusing and
half-broken under certain circumstances. This problem doesn't
exist for non-reentrant workqueues. While non-reentrancy check
isn't free, the overhead is incurred only when a work item bounces
across different CPUs and even in simulated pathological scenario
the overhead isn't too high.
All workqueues are made non-reentrant. This removes the
distinction between flush_[delayed_]work() and
flush_[delayed_]_work_sync(). The former is now as strong as the
latter and the specified work item is guaranteed to have finished
execution of any previous queueing on return.
* In addition to the various bug fixes, Lai redid and simplified CPU
hotplug handling significantly.
* Joonsoo introduced system_highpri_wq and used it during CPU
hotplug.
There are two merge commits - one to pull in IRQ safe timer from
tip/timers/core and the other to pull in CPU hotplug fixes from
wq/for-3.6-fixes as Lai's hotplug restructuring depended on them."
Fixed a number of trivial conflicts, but the more interesting conflicts
were silent ones where the deprecated interfaces had been used by new
code in the merge window, and thus didn't cause any real data conflicts.
Tejun pointed out a few of them, I fixed a couple more.
* 'for-3.7' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/wq: (46 commits)
workqueue: remove spurious WARN_ON_ONCE(in_irq()) from try_to_grab_pending()
workqueue: use cwq_set_max_active() helper for workqueue_set_max_active()
workqueue: introduce cwq_set_max_active() helper for thaw_workqueues()
workqueue: remove @delayed from cwq_dec_nr_in_flight()
workqueue: fix possible stall on try_to_grab_pending() of a delayed work item
workqueue: use hotcpu_notifier() for workqueue_cpu_down_callback()
workqueue: use __cpuinit instead of __devinit for cpu callbacks
workqueue: rename manager_mutex to assoc_mutex
workqueue: WORKER_REBIND is no longer necessary for idle rebinding
workqueue: WORKER_REBIND is no longer necessary for busy rebinding
workqueue: reimplement idle worker rebinding
workqueue: deprecate __cancel_delayed_work()
workqueue: reimplement cancel_delayed_work() using try_to_grab_pending()
workqueue: use mod_delayed_work() instead of __cancel + queue
workqueue: use irqsafe timer for delayed_work
workqueue: clean up delayed_work initializers and add missing one
workqueue: make deferrable delayed_work initializer names consistent
workqueue: cosmetic whitespace updates for macro definitions
workqueue: deprecate system_nrt[_freezable]_wq
workqueue: deprecate flush[_delayed]_work_sync()
...
acpi_os_map_memory expects its return value to be in the __iomem address
space. Tag the variable we're using as such and use memcpy_fromio to
avoid further sparse warnings.
Signed-off-by: Kent Yoder <key@linux.vnet.ibm.com>
Signed-off-by: James Morris <james.l.morris@oracle.com>
This patch declares the internal struct and functions as static to provide
more security.
Signed-off-by: Xiaoyan Zhang <xiaoyan.zhang@intel.com>
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Reviewed-by: Kent Yoder <key@linux.vnet.ibm.com>
Signed-off-by: James Morris <james.l.morris@oracle.com>
The Physical Presence Interface enables the OS and the BIOS to cooperate and
provides a simple and straightforward platform user experience for
administering the TPM without sacrificing security.
V2: separate the patch out in a separate source file,
add #ifdef CONFIG_ACPI so it compiles out on ppc,
use standard error instead of ACPI error as return code of show/store fns.
V3: move #ifdef CONFIG_ACPI from .c file to .h file.
V4: move tpm_ppi code from tpm module to tpm_bios module.
V5: modify sys_add_ppi() so that ppi_attr_grp doesn't need to be exported
Signed-off-by: Xiaoyan Zhang <xiaoyan.zhang@intel.com>
Signed-off-by: Kent Yoder <key@linux.vnet.ibm.com>
In drivers/char/tpm/tpm_acpi.c::read_log() we call
acpi_os_map_memory(). That call may fail for a number of reasons
(invalid address, out of memory etc). If the call fails it returns
NULL and we just pass that to memcpy() unconditionally, which will go
bad when it tries to dereference the pointer.
Unfortunately we just get NULL back, so we can't really tell the user
exactely what went wrong, but we can at least avoid crashing and
return an error (-EIO seemed more generic and more suitable here than
-ENOMEM or something else, so I picked that).
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Signed-off-by: Kent Yoder <key@linux.vnet.ibm.com>
This patch retrieves the event log data from the device tree
during file open. The event log data will then displayed through
securityfs.
Signed-off-by: Ashley Lai <adlai@us.ibm.com>
Signed-off-by: Kent Yoder <key@linux.vnet.ibm.com>
This patch adds a new device driver to support IBM virtual TPM
(vTPM) for PPC64. IBM vTPM is supported through the adjunct
partition with firmware release 740 or higher. With vTPM
support, each lpar is able to have its own vTPM without the
physical TPM hardware.
This driver provides TPM functionalities by communicating with
the vTPM adjunct partition through Hypervisor calls (Hcalls)
and Command/Response Queue (CRQ) commands.
Signed-off-by: Ashley Lai <adlai@us.ibm.com>
Signed-off-by: Kent Yoder <key@linux.vnet.ibm.com>
The tpm_tis driver doesn't use tpm_tis_resume except when PM is
configured and doesn't make use of tpm_tis_reenable_interrupts except
when PM or PNP is configured.
Signed-off-by: Kent Yoder <key@linux.vnet.ibm.com>
Moved the atomic_set of the data_pending variable until after the
tpm_read has completed processing. The existing code had a window of
time where a second write to the driver could clobber the tpm command
buffer.
Also fixed an issue where if close was called on the tpm device before a
read completed, the tpm command buffer would be returned to the OS,
which could contain sensitive information.
Signed-off-by: Kent Yoder <key@linux.vnet.ibm.com>
Move the tpm_get_random api from the trusted keys code into the TPM
device driver itself so that other callers can make use of it. Also,
change the api slightly so that the number of bytes read is returned in
the call, since the TPM command can potentially return fewer bytes than
requested.
Acked-by: David Safford <safford@linux.vnet.ibm.com>
Reviewed-by: H. Peter Anvin <hpa@linux.intel.com>
Signed-off-by: Kent Yoder <key@linux.vnet.ibm.com>
Break ACPI-specific pieces of the event log handling into their own file
and create tpm_eventlog.[ch] to store common event log handling code.
This will be required to integrate future event log sources on platforms
without ACPI tables.
Signed-off-by: Kent Yoder <key@linux.vnet.ibm.com>
This patch adds a driver to support Infineon's SLB 9635 TT 1.2 Soft I2C TPMs
which follow the TGC TIS 1.2 TPM specification[1] and Infineon's I2C Protocol
Stack Specification 0.20.
The I2C Protocol Stack Specification is a simple adaption of the LPC TIS
Protocol to the I2C Bus.
The I2C TPMs can be used when LPC Bus is not available (i.e. non x86
architectures like ARM).
The driver is based on the tpm_tis.c driver by Leendert van Dorn and Kyleen
Hall and has quite similar functionality.
Tested on Nvidia ARM Tegra2 Development Platform and Beagleboard (ARM OMAP)
Tested with the Trousers[2] TSS API Testsuite v 0.3 [3]
Compile-tested on x86 (32/64-bit)
Updates since version 2.1.4:
- included "Lock the I2C adapter for a sequence of requests", by Bryan Freed
- use __i2c_transfer instead of own implementation of unlocked i2c_transfer
- use struct dev_pm_ops for power management via SIMPLE_DEV_PM_OPS
Updates since version 2.1.3:
- use proper probing mechanism
* either add the tpm using I2C_BOARD_INFO to your board file or probe it
* during runtime e.g on BeagleBoard using :
* "echo tpm_i2c_infineon 0x20 > /sys/bus/i2c/devices/i2c-2/new_device"
- fix possible endless loop if hardware misbehaves
- improved return codes
- consistent spelling i2c/tpm -> I2C/TPM
- remove hardcoded sleep values and msleep usage
- removed debug statements
- added check for I2C functionality
- renaming to tpm_i2c_infineon
Updates since version 2.1.2:
- added sysfs entries for duration and timeouts
- updated to new tpm_do_selftest
Updates since version 2.1.0:
- improved error handling
- implemented workarounds needed by the tpm
- fixed typos
References:
[1]
http://www.trustedcomputinggroup.org/resources/pc_client_work_group_pc_client_
specific_tpm_interface_specification_tis_version_12/
[2] http://trousers.sourceforge.net/
[3]
http://sourceforge.net/projects/trousers/files/TSS%20API%20test%20suite/0.3/
Reviewed-by: Andi Shyti <andi.shyti@gmail.com>
Acked-by: Marcel Selhorst <tpmdd@selhorst.net>
Signed-off-by: Peter Huewe <peter.huewe@infineon.com>
Signed-off-by: Bryan Freed <bfreed@chromium.org>
Signed-off-by: Kent Yoder <key@linux.vnet.ibm.com>
flush[_delayed]_work_sync() are now spurious. Mark them deprecated
and convert all users to flush[_delayed]_work().
If you're cc'd and wondering what's going on: Now all workqueues are
non-reentrant and the regular flushes guarantee that the work item is
not pending or running on any CPU on return, so there's no reason to
use the sync flushes at all and they're going away.
This patch doesn't make any functional difference.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Ian Campbell <ian.campbell@citrix.com>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Mattia Dongili <malattia@linux.it>
Cc: Kent Yoder <key@linux.vnet.ibm.com>
Cc: David Airlie <airlied@linux.ie>
Cc: Jiri Kosina <jkosina@suse.cz>
Cc: Karsten Keil <isdn@linux-pingi.de>
Cc: Bryan Wu <bryan.wu@canonical.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Alasdair Kergon <agk@redhat.com>
Cc: Mauro Carvalho Chehab <mchehab@infradead.org>
Cc: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: linux-wireless@vger.kernel.org
Cc: Anton Vorontsov <cbou@mail.ru>
Cc: Sangbeom Kim <sbkim73@samsung.com>
Cc: "James E.J. Bottomley" <James.Bottomley@HansenPartnership.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Eric Van Hensbergen <ericvh@gmail.com>
Cc: Takashi Iwai <tiwai@suse.de>
Cc: Steven Whitehouse <swhiteho@redhat.com>
Cc: Petr Vandrovec <petr@vandrovec.name>
Cc: Mark Fasheh <mfasheh@suse.com>
Cc: Christoph Hellwig <hch@infradead.org>
Cc: Avi Kivity <avi@redhat.com>
According to a compiler warning, the tpm_tis_resume() function is not
used for CONFIG_PM_SLEEP unset, so add a #ifdef to prevent it from
being built in that case.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Pull security subsystem updates from James Morris:
"Nothing groundbreaking for this kernel, just cleanups and fixes, and a
couple of Smack enhancements."
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security: (21 commits)
Smack: Maintainer Record
Smack: don't show empty rules when /smack/load or /smack/load2 is read
Smack: user access check bounds
Smack: onlycap limits on CAP_MAC_ADMIN
Smack: fix smack_new_inode bogosities
ima: audit is compiled only when enabled
ima: ima_initialized is set only if successful
ima: add policy for pseudo fs
ima: remove unused cleanup functions
ima: free securityfs violations file
ima: use full pathnames in measurement list
security: Fix nommu build.
samples: seccomp: add .gitignore for untracked executables
tpm: check the chip reference before using it
TPM: fix memleak when register hardware fails
TPM: chip disabled state erronously being reported as error
MAINTAINERS: TPM maintainers' contacts update
Merge branches 'next-queue' and 'next' into next
Remove unused code from MPI library
Revert "crypto: GnuPG based MPI lib - additional sources (part 4)"
...
