Large (> 1 TiB) UDF filesystems appear subject to several problems when
mounted on 64-bit systems:
* readdir() can fail on a directory containing File Identifiers residing
above 0x7FFFFFFF. This manifests as a 'ls' command failing with EIO.
* FIBMAP on a file block located above 0x7FFFFFFF can return a negative
value. The low 32 bits are correct, but applications that don't mask the
high 32 bits of the result can perform incorrectly.
Per suggestion by Jan Kara, introduce a udf_pblk_t type for representation
of UDF block addresses. Ultimately, all driver functions that manipulate
UDF block addresses should use this type; for now, deployment is limited
to functions with actual or potential sign extension issues.
Changes to udf_readdir() and udf_block_map() address the issues noted
above; other changes address potential similar issues uncovered during
audit of the driver code.
Signed-off-by: Steven J. Magnani <steve@digidescorp.com>
Signed-off-by: Jan Kara <jack@suse.cz>
These two are confusing leftover of the old world order, combining
values of the REQ_OP_ and REQ_ namespaces. For callers that don't
special case we mostly just replace bi_rw with bio_data_dir or
op_is_write, except for the few cases where a switch over the REQ_OP_
values makes more sense. Any check for READA is replaced with an
explicit check for REQ_RAHEAD. Also remove the READA alias for
REQ_RAHEAD.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Mike Christie <mchristi@redhat.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
This has ll_rw_block users pass in the operation and flags separately,
so ll_rw_block can setup the bio op and bi_rw flags on the bio that
is submitted.
Signed-off-by: Mike Christie <mchristi@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Code in udf_find_entry() and udf_readdir() used the same buffer for
storing filename that was split among blocks and for the resulting
filename in utf8. This worked because udf_get_filename() first
internally copied the name into a different buffer and only then
performed a conversion into the destination buffer. However we want to
get rid of intermediate buffers so use separate buffer for converted
name and name split between blocks so that we don't have the same source
and destination buffer when converting split names.
Signed-off-by: Jan Kara <jack@suse.cz>
Zero length file name isn't really valid. So check the length of the
final file name generated by udf_translate_to_linux() and return -EINVAL
instead of zero length file name. Update caller of udf_get_filename() to
not check for 0 return value.
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: Jan Kara <jack@suse.cz>
Return -ENOMEM when allocation fails in udf_get_filename(). Update
udf_pc_to_char(), udf_readdir(), and udf_find_entry() to handle the
error appropriately. This allows us to pass appropriate error to
userspace instead of corrupting symlink contents by omitting some path
elements.
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: Jan Kara <jack@suse.cz>
Symlink reading code does not check whether the resulting path fits into
the page provided by the generic code. This isn't as easy as just
checking the symlink size because of various encoding conversions we
perform on path. So we have to check whether there is still enough space
in the buffer on the fly.
CC: stable@vger.kernel.org
Reported-by: Carl Henrik Lunde <chlunde@ping.uio.no>
Signed-off-by: Jan Kara <jack@suse.cz>
The udf_readdir(), udf_lookup(), udf_create(), udf_mknod(), udf_mkdir(),
udf_rmdir(), udf_link(), udf_get_parent() and udf_unlink() seems already
adequately protected by i_mutex held by VFS invoking calls. The udf_rename()
instead should be already protected by lock_rename again by VFS. The
udf_ioctl(), udf_fill_super() and udf_evict_inode() don't requires any further
protection.
This work was supported by a hardware donation from the CE Linux Forum.
Signed-off-by: Alessio Igor Bogani <abogani@texware.it>
Signed-off-by: Jan Kara <jack@suse.cz>
We don't name our generic fsync implementations very well currently.
The no-op implementation for in-memory filesystems currently is called
simple_sync_file which doesn't make too much sense to start with,
the the generic one for simple filesystems is called simple_fsync
which can lead to some confusion.
This patch renames the generic file fsync method to generic_file_fsync
to match the other generic_file_* routines it is supposed to be used
with, and the no-op implementation to noop_fsync to make it obvious
what to expect. In addition add some documentation for both methods.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Do not use the fallback default_llseek() if the readdir operation of the
filesystem still uses the big kernel lock.
Since llseek() modifies
file->f_pos of the directory directly it may need locking to not confuse
readdir which usually uses file->f_pos directly as well
Since the special characteristics of the BKL (unlocked on schedule) are
not necessary in this case, the inode mutex can be used for locking as
provided by generic_file_llseek(). This is only possible since all
filesystems, except reiserfs, either use a directory as a flat file or
with disk address offsets. Reiserfs on the other hand uses a 32bit hash
off the filename as the offset so generic_file_llseek() can get used as
well since the hash is always smaller than sb->s_maxbytes (= (512 << 32) -
blocksize).
Signed-off-by: Jan Blunck <jblunck@suse.de>
Acked-by: Jan Kara <jack@suse.cz>
Acked-by: Anders Larsen <al@alarsen.net>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Convert udf_ioctl to an unlocked_ioctl and push the BKL down into it.
Signed-off-by: John Kacur <jkacur@redhat.com
Signed-off-by: Jan Kara <jack@suse.cz>
There are several places in UDF where we declared temporary arrays of
UDF_NAME_LEN bytes on stack. This is not nice to stack usage so this patch
changes those places to use kmalloc() instead. Also clean up bail-out paths
in those functions when we are changing them.
Signed-off-by: Jan Kara <jack@suse.cz>
There's not need to document vfs method invocation rules, we have
Documentation/filesystems/vfs.txt and Documentation/filesystems/Locking
for that. Also a lot of these comments where either plain wrong or
horrible out of date.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jan Kara <jack@suse.cz>
Patch cleaning up UDF directory offset handling missed modifications in dir.c
(because I've submitted an old version :(). Fix it.
Signed-off-by: Jan Kara <jack@suse.cz>
Reported-by: Marcin Slusarz <marcin.slusarz@gmail.com>
Tested-by: Marcin Slusarz <marcin.slusarz@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
sparse generated:
fs/udf/dir.c:78:5: warning: symbol 'udf_readdir' was not declared. Should it be static?
there are 2 different prototypes of udf_readdir - remove them and move
code around to make it still compile
Signed-off-by: Marcin Slusarz <marcin.slusarz@gmail.com>
Acked-by: Jan Kara <jack@suse.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
cache UDF_I(struct inode *) return values when there are
at least 2 uses in one function
Signed-off-by: Marcin Slusarz <marcin.slusarz@gmail.com>
Acked-by: Jan Kara <jack@suse.cz>
Cc: Christoph Hellwig <hch@lst.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Marcin Slusarz <marcin.slusarz@gmail.com>
Acked-by: Jan Kara <jack@suse.cz>
Cc: Christoph Hellwig <hch@lst.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch fixes up sources after conversion by Lindent.
Signed-off-by: Cyrill Gorcunov <gorcunov@gmail.com>
Cc: Jan Kara <jack@ucw.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch converts UDF coding style to kernel coding style using Lindent.
Signed-off-by: Cyrill Gorcunov <gorcunov@gmail.com>
Cc: Jan Kara <jack@ucw.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Make UDF use get_bh() instead of directly accessing b_count and use
brelse() instead of udf_release_data() which does just brelse()...
Signed-off-by: Jan Kara <jack@suse.cz>
Acked-by: Christoph Hellwig <hch@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Introduce a structure extent_position to store a position of an extent and
the corresponding buffer_head in one place.
Signed-off-by: Jan Kara <jack@suse.cz>
Acked-by: Christoph Hellwig <hch@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Use sector_t and loff_t for file offsets in UDF filesystem. Otherwise an
overflow may occur for long files. Also make inode_bmap() return offset in
the extent in number of blocks instead of number of bytes - for most
callers this is more convenient.
Signed-off-by: Jan Kara <jack@suse.cz>
Acked-by: Christoph Hellwig <hch@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This is a conversion to make the various file_operations structs in fs/
const. Basically a regexp job, with a few manual fixups
The goal is both to increase correctness (harder to accidentally write to
shared datastructures) and reducing the false sharing of cachelines with
things that get dirty in .data (while .rodata is nicely read only and thus
cache clean)
Signed-off-by: Arjan van de Ven <arjan@infradead.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.
Let it rip!
Steve Magnani