When James Smart fixed the issue of the userspace scan atributes
crashing the system with the FC transport class he added a patch to
let the transport class check if the parent is valid for a given
transport class.
When adding support for the integrated raid of fusion sas devices
we ran into a problem with that, as it didn't allow adding virtual
raid volumes without the transport class knowing about it.
So this patch adds a user_scan attribute instead, that takes over from
scsi_scan_host_selected if the transport class sets it and thus lets
the transport class control the user-initiated scanning. As this
plugs the hole about user-initiated scanning the target_parent hook
goes away and we rely on callers of the scanning routines to do
something sensible.
For SAS this meant I had to switch from a spinlock to a mutex to
synchronize the topology linked lists, in FC they were completely
unsynchronized which seems wrong.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Convert the SCSI transport class code to use a mutex rather than a
semaphore.
Signed-off-by: Jes Sorensen <jes@sgi.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Add fc_host attribute permanent_port_name which is
used to show the port name of the primary port -
the port that initially logged into the fabric.
For a virtual port (registered via the primary port with
FDISC command) it is useful to know not only its (virtual)
port name but also the permanent port name.
Signed-off-by: Andreas Herrmann <aherrman@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
LLDDs should never see REQ_BLOCK_PC requests, we can handle them just
fine in the core code. There is a small behaviour change in that some
check in sr's rw_intr are bypassed, but I consider the old behaviour
a bug.
Mike found this cleanup opportunity and provdided early patches, so all
the credit goes to him, even if I redid the patches from scratch beause
that was easier than forward-porting the old patches.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
the scsi layer is using semaphores in a mutex way, this patch converts
these into using mutexes instead
Signed-off-by: Arjan van de Ven <arjan@infradead.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This patch adds suspend patch to libata, and ata_piix in particular. For
most low level drivers, they should just need to add the 4 hooks to
work. As I can only test ata_piix, I didn't enable it for more
though.
Suspend support is the single most important feature on a notebook, and
most new notebooks have sata drives. It's quite embarrassing that we
_still_ do not support this. Right now, it's perfectly possible to
suspend the drive in mid-transfer.
Signed-off-by: Jens Axboe <axboe@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
All ordered request related stuff delegated to HLD. Midlayer
now doens't deal with ordered setting or prepare_flush
callback. sd.c updated to deal with blk_queue_ordered
setting. Currently, ordered tag isn't used as SCSI midlayer
cannot guarantee request ordering.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jens Axboe <axboe@suse.de>
In the scenario that a link was broken, the devloss timer for each
rport was expire at roughly the same time, causing lots of "delete"
workqueue items being queued. Depth is dependent upon the number of
rports that were on the link.
The rport target remove calls were calling flush_scheduled_work(),
which would interrupt the stream, and start the next workqueue item,
which did the same thing, and so on until recursion depth was large.
This fix stops the recursion in the initial delete path, and pushes it
off to a host-level work item that reaps the dead rports.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Rename scsi_print_msg to spi_print_msg and move its prototype from
scsi_dbg.h to scsi_transport_spi.h
Signed-off-by: Matthew Wilcox <matthew@wil.cx>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This merge is pretty extensive. The conflict is over the new
req->retries parameter, so I had to change the prototype to
scsi_setup_blk_pc_cmnd() and the usage in sd, sr and st.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Add scsi helpers to create really-large-requests and convert
scsi-ml to scsi_execute_async().
Per Jens's previous comments, I placed this function in scsi_lib.c.
I made it follow all the queue's limits - I think I did at least :), so
I removed the warning on the function header.
I think the scsi_execute_* functions should eventually take a request_queue
and be placed some place where the dm-multipath hw_handler can use them
if that failover code is going to stay in the kernel. That conversion
patch will be sent in another mail though.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This follows on from Jens' patch and consolidates all of the ULD
separate handlers for REQ_BLOCK_PC into a single call which has his
fix for our direction bug.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Add forward declarations to allow scsi_transport_spi.h to be compiled by
itself.
Signed-off-by: Matthew Wilcox <matthew@wil.cx>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Make the vendor, model and rev fields in scsi_device pointers to const
and update a few prototypes of functions using them.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
scsi_send_eh_cmnd currently uses a semaphore and an overload of eh_timer
to either get a completion for a command for a timeout.
Switch to using a completion and wait_for_completion_timeout to simply
the code and not having to deal with the races ourselves.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This function has been superceeded by the block request based interfaces
and is unused (except for the uncompilable cpqfc driver).
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
now that the abuse in qla2xxx is gone this field can be remove.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Add an InfiniBand SCSI RDMA Protocol (SRP) initiator. This driver is
used to talk talk to InfiniBand SRP targets (storage devices).
Signed-off-by: Roland Dreier <rolandd@cisco.com>
I recently picked up my older work to remove unnecessary #includes of
sched.h, starting from a patch by Dave Jones to not include sched.h
from module.h. This reduces the number of indirect includes of sched.h
by ~300. Another ~400 pointless direct includes can be removed after
this disentangling (patch to follow later).
However, quite a few indirect includes need to be fixed up for this.
In order to feed the patches through -mm with as little disturbance as
possible, I've split out the fixes I accumulated up to now (complete for
i386 and x86_64, more archs to follow later) and post them before the real
patch. This way this large part of the patch is kept simple with only
adding #includes, and all hunks are independent of each other. So if any
hunk rejects or gets in the way of other patches, just drop it. My scripts
will pick it up again in the next round.
Signed-off-by: Tim Schmielau <tim@physik3.uni-rostock.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
We recently went back to implement a board reset. When we perform the
reset, we wanted to tear down the internal data structures and rebuild
them. Unfortunately, when it came to the rport structure, things were
odd. If we deleted them, the scsi targets and sdevs would be
torn down. Not a good thing for a temporary reset. We could block the
rports, but we either maintain the internal structures to keep the
rport reference (perhaps even replicating what's in the transport),
or we have to fatten the fc transport with new search routines to find
the rport (and deal with a case of a dangling rport that the driver
forgets).
It dawned on me that we had actually reached this state incorrectly.
When the fc transport first started, we did the block/unblock first, then
added the rport interface. The purpose of block/unblock is to hide the
temporary disappearance of the rport (e.g. being deleted, then readded).
Why are we making the driver do the block/unblock ? We should be making
the transport have only an rport add/delete, and the let the transport
handle the block/unblock.
So... This patch removes the existing fc_remote_port_block/unblock
functions. It moves the block/unblock functionality into the
fc_remote_port_add/delete functions. Updates for the lpfc driver are
included. Qlogic driver updates are also enclosed, thanks to the
contributions of Andrew Vasquez. [Note: the qla2xxx changes are
relative to the scsi-misc-2.6 tree as of this morning - which does
not include the recent patches sent by Andrew]. The zfcp driver does
not use the block/unblock functions.
One last comment: The resulting behavior feels very clean. The LLDD is
concerned only with add/delete, which corresponds to the physical
disappearance. However, the fact that the scsi target and sdevs are
not immediately torn down after the LLDD calls delete causes an
interesting scenario... the midlayer can call the xxx_slave_alloc and
xxx_queuecommand functions with a sdev that is at the location the
rport used to be. The driver must validate the device exists when it
first enters these functions. In thinking about it, this has always
been the case for the LLDD and these routines. The existing drivers
already check for existence. However, this highlights that simple
validation via data structure dereferencing needs to be watched.
To deal with this, a new transport function, fc_remote_port_chkready()
was created that LLDDs should call when they first enter these two
routines. It validates the rport state, and returns a scsi result
which could be returned. In addition to solving the above, it also
creates consistent behavior from the LLDD's when the block and deletes
are occuring.
Rejections fixed up and
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
New dev_printk wrappers, which allow us to shrink code, and
eliminate direct references to host/channel/id/lun members:
scmd_printk()
Introduce wrappers for highly common idioms, which may also help us
eliminate some ->{channel,id} references in the future:
{scmd,sdev}_id()
{scmd,sdev}_channel()
The scmd_* wrappers are present in scsi/scsi_device.h because they all
employ the dereference chain cmd->device->$member. We would prefer to
use static inline functions rather than macros, but that would have a
Rejections fixed up and
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Ok, here's a patch to add such a common API for fc transport users.
Relevant LLD changes (lpfc and qla2xxx) also present.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Add a flag to mark a PHY as attached to the HBA as opposed to beeing on
an expander. This is needed because various features are only supported
on those. This is a crude hack, the proper fix would be to use
different classes for host-attached vs expander phys. I'm looking into
that.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
For now supporting the ->get_linkerrors method is mandatory. I'll
probably be beaten to implement the .show_foo variables and different
types of attributes soon..
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This should eliminate (at least in the mid layer) to make numeric
assumptions about any of the enumeration variables. As a side effect,
it will also make all the messages consistent and line us up nicely for
the error logging strategy (if it ever shows itself again).
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Currently we just ignore the device, which means there are a few
arrays out there that we don't find.
This patch updates the scsi_report_lun_scan() to take a target instead
of a device so it can be called on a return of
SCSI_SCAN_TARGET_PRESENT, which is what a PQ 3 device returns.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
From: hare@suse.de
for a proper alignment between open-iscsi and iscsitarget the
definitions in include/iscsi_proto.h do not match exactly.
With this patch it's possible to have iscsitarget use
'include/iscsi_proto.h' instead of its own iscsi_hdr.h.
Signed-off-by: Alex Aizman <itn780@yahoo.com>
Signed-off-by: Dmitry Yusupov <dmitry_yus@yahoo.com>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
From: michaelc@cs.wisc.edu
Cleanup some iscsi_proto defs, add some missing values, and
fix some defs.
Signed-off-by: Alex Aizman <itn780@yahoo.com>
Signed-off-by: Dmitry Yusupov <dmitry_yus@yahoo.com>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
From: Alan Stern <stern@rowland.harvard.edu>
This patch (as561) fixes the error handler's thread-exit code. The
kthread_stop call won't wake the thread from a down_interruptible, so
the patch gets rid of the semaphore and simply does
set_current_state(TASK_INTERRUPTIBLE);
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Modified to simplify the termination loop and correct the sleep condition.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
We fix the oops by enforcing the host state model. There have also
been two extra states added: SHOST_CANCEL_RECOVERY and
SHOST_DEL_RECOVERY so we can take the model through host removal while
the recovery thread is active.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
obviously FC Port Speeds in scsi_transport_fc.h are defined according
to FC-HBA:
#define FC_PORTSPEED_1GBIT 1
#define FC_PORTSPEED_2GBIT 2
#define FC_PORTSPEED_10GBIT 4
#define FC_PORTSPEED_4GBIT 8
Problem is, whoever invented FC-HBA did not care about FC-FS or
FC-GS-x. Following FC-FS/FC-GS-x defintions of port speeds would look
like:
1 GBit: 0x0001
2 GBit: 0x0002
4 GBit: 0x0004
10GBit: 0x0008
(and new in FC-LS:
8 Gbit: 0x0010
16GBit: 0x0020)
I really appreciate if scsi_transport_fc.h would define port speeds
according to FC-GS-x/FC-FS. Thus mapping of port speed capabilities to
values defined in scsi_transport_fc.h can be avoided in the LLDD.
Attached is a patch to change the definitions.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
The original API returned either an ERR_PTR() or a refcounted sdev.
Unfortunately, if it's successful, you need to do a scsi_device_put() on
the sdev otherwise the refcounting is wrong.
Everyone seems to expect that scsi_add_device() should be callable
without doing the ref put, so alter the API so it is (we still have
__scsi_add_device with the original behaviour).
The only actual caller that needs altering is the one in firewire ...
not because it gets this right, but because it acts on the error if one
is returned.
Acked-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
On some platforms the hard-casting of 8 byte node_name and
port_name arrays to an u64 would cause unaligned-access
warnings. Generalize the conversions with a transport
helper function which performs consistent shifting of WWN
bytes.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
The SAS transport class contains common code to deal with SAS HBAs, an
aproximated representation of SAS topologies in the driver model,
and various sysfs attributes to expose these topologies and managment
interfaces to userspace.
In addition to the basic SCSI core objects this transport class introduces
two additional intermediate objects: The SAS PHY as represented by struct
sas_phy defines an "outgoing" PHY on a SAS HBA or Expander, and the SAS
remote PHY represented by struct sas_rphy defines an "incoming" PHY on a
SAS Expander or end device. Note that this is purely a software concept, the
underlying hardware for a PHY and a remote PHY is the exactly the same.
There is no concept of a SAS port in this code, users can see what PHYs
form a wide port based on the port_identifier attribute, which is the same
for all PHYs in a port.
This submission doesn't handle hot-plug addition or removal of SAS devices
and thus doesn't do scanning in a workqueue yet, that will be added in
phase2 after this submission. In a third phase I will add additional
managment infrastructure.
I think this submission is ready for 2.6.14, but additional comments are
of course very welcome.
I'd like to thanks James Smart a lot for his very useful input on the
design.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
