Commit Graph

22 Commits

Author SHA1 Message Date
Simon Arlott 4ac0718e83 USB: cxacru: Use appropriate logging for errors
When an error occurs, existing logging uses dbg() so the cause of a
problem is hard to determine. Error conditions shouldn't only be
properly reported with debugging enabled.

A side effect of this change is that when an uninitialised device is
started, a log message similar to the following is sent:
	cxacru 5-2:1.0: receive of cm 0x90 failed (-104)
This is normal - the device did not respond so firmware will be loaded.

Signed-off-by: Simon Arlott <simon@fire.lp0.eu>
Acked-by: Duncan Sands <baldrick@free.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2007-10-12 14:55:28 -07:00
Oliver Neukum 3b79cc2670 USB: unkill cxacru atm driver
it seems like you overdid it a bit in your quest to clean up the
use of urb->status. In this driver you read it the first thing, which
means that you are in a race against URB completion you'll
usually lose, returning -EINPROGRESS. This kills the driver.

Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2007-08-22 14:27:58 -07:00
Greg Kroah-Hartman c35f68a05d USB: atm: cxacru: clean up urb->status usage
This done in anticipation of removal of urb->status, which will make
that patch easier to review and apply in the future.

Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2007-07-19 17:46:05 -07:00
Simon Arlott 87e71b473e USB: cxacru: Cleanup sysfs attribute code
This changes the format of unknown status values to be less verbose and
uses an array instead of several different snprintf calls. Since only
enum values are assigned to it, poll_state is changed from int to enum.
Use abs() for dB values instead of two almost identical return lines.

Signed-off-by: Simon Arlott <simon@fire.lp0.eu>
Acked-by: Duncan Sands <duncan.sands@math.u-psud.fr>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2007-07-12 16:29:45 -07:00
Simon Arlott fd209e35b7 USB: cxacru: ignore error trying to start ADSL in atm_start
The sysfs adsl_status attribute ignores (aside from returning -EIO to the
user) any error sending a START/STOP command to the device and there is at
least one firmware which never sends a response but appears to work
regardless.  Therefore atm_start should also continue if an error is received
so that such firmware is usable.

The official Conexant driver doesn't expect a reply either but this is for
another device (E2 router) and a commonly used firmware does respond.

Also, there is no point in changing -ECONNRESET to -ETIMEDOUT since nothing
ever checks for either of these values.

Signed-off-by: Simon Arlott <simon@fire.lp0.eu>
Cc: Duncan Sands <duncan.sands@math.u-psud.fr>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2007-06-08 16:24:31 -07:00
Simon Arlott da1f82b554 USB: cxacru: create sysfs attributes in atm_start instead of bind
Since usbatm doesn't set the usb_interface driver data until after calling
bind and heavy_init, it would be NULL when the sysfs attributes are read.
Reading the MAC address from atm_dev before atm_dev exists would have been
be possible too.

Calling create_device_file in atm_start will avoid this problem, and the
data is useless until the first status poll runs.  However, it must be
ready before a status poll does a printk on line status change otherwise
userspace could react before the files exist.

For completeness I've moved remove_device_file to atm_stop so it's not
called in unbind when it's not needed.  There's no point starting ADSL if
atm_start could still fail either.

Signed-off-by: Simon Arlott <simon@fire.lp0.eu>
Cc: Duncan Sands <duncan.sands@math.u-psud.fr>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2007-06-08 16:24:31 -07:00
Simon Arlott 6a02c996bc USB: cxacru: ADSL state management
The device has commands to start/stop the ADSL function, so this adds a
sysfs attribute to allow it to be started/stopped/restarted.  It also stops
polling the device for status when the ADSL function is disabled.

There are no problems with sending multiple start or stop commands, even
with a fast loop of them the device still works.  There is no need to
protect the restart process from further user actions while it's waiting
for 1.5s.

Signed-off-by: Simon Arlott <simon@fire.lp0.eu>
Cc: Duncan Sands <duncan.sands@math.u-psud.fr>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2007-04-27 13:28:41 -07:00
Simon Arlott fa70fe44ab USB: cxacru: export detailed device info through sysfs
When the device is polled for status there is a lot of useful status
information available that is ignored.  This patch stores the device info
array when the status is polled and adds sysfs files to the usb device to
allow userspace to query it.  Since the device updates its status
internally once a second the poll time is changed to this, and
round_jiffies_relative is used to avoid waking the cpu unnecessarily.

Signed-off-by: Simon Arlott <simon@fire.lp0.eu>
Cc: Duncan Sands <duncan.sands@free.fr>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2007-04-27 13:28:34 -07:00
David Howells c4028958b6 WorkStruct: make allyesconfig
Fix up for make allyesconfig.

Signed-Off-By: David Howells <dhowells@redhat.com>
2006-11-22 14:57:56 +00:00
Duncan Sands 44960af1b6 cxacru: add the ZTE ZXDSL 852
From http://doc.ubuntu-fr.org/materiel/zxdsl852.

Signed-off-by: Duncan Sands <baldrick@free.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2006-10-17 14:46:31 -07:00
David Howells 7d12e780e0 IRQ: Maintain regs pointer globally rather than passing to IRQ handlers
Maintain a per-CPU global "struct pt_regs *" variable which can be used instead
of passing regs around manually through all ~1800 interrupt handlers in the
Linux kernel.

The regs pointer is used in few places, but it potentially costs both stack
space and code to pass it around.  On the FRV arch, removing the regs parameter
from all the genirq function results in a 20% speed up of the IRQ exit path
(ie: from leaving timer_interrupt() to leaving do_IRQ()).

Where appropriate, an arch may override the generic storage facility and do
something different with the variable.  On FRV, for instance, the address is
maintained in GR28 at all times inside the kernel as part of general exception
handling.

Having looked over the code, it appears that the parameter may be handed down
through up to twenty or so layers of functions.  Consider a USB character
device attached to a USB hub, attached to a USB controller that posts its
interrupts through a cascaded auxiliary interrupt controller.  A character
device driver may want to pass regs to the sysrq handler through the input
layer which adds another few layers of parameter passing.

I've build this code with allyesconfig for x86_64 and i386.  I've runtested the
main part of the code on FRV and i386, though I can't test most of the drivers.
I've also done partial conversion for powerpc and MIPS - these at least compile
with minimal configurations.

This will affect all archs.  Mostly the changes should be relatively easy.
Take do_IRQ(), store the regs pointer at the beginning, saving the old one:

	struct pt_regs *old_regs = set_irq_regs(regs);

And put the old one back at the end:

	set_irq_regs(old_regs);

Don't pass regs through to generic_handle_irq() or __do_IRQ().

In timer_interrupt(), this sort of change will be necessary:

	-	update_process_times(user_mode(regs));
	-	profile_tick(CPU_PROFILING, regs);
	+	update_process_times(user_mode(get_irq_regs()));
	+	profile_tick(CPU_PROFILING);

I'd like to move update_process_times()'s use of get_irq_regs() into itself,
except that i386, alone of the archs, uses something other than user_mode().

Some notes on the interrupt handling in the drivers:

 (*) input_dev() is now gone entirely.  The regs pointer is no longer stored in
     the input_dev struct.

 (*) finish_unlinks() in drivers/usb/host/ohci-q.c needs checking.  It does
     something different depending on whether it's been supplied with a regs
     pointer or not.

 (*) Various IRQ handler function pointers have been moved to type
     irq_handler_t.

Signed-Off-By: David Howells <dhowells@redhat.com>
(cherry picked from 1b16e7ac850969f38b375e511e3fa2f474a33867 commit)
2006-10-05 15:10:12 +01:00
Arjan van de Ven ab3c81ff63 [PATCH] USBATM: semaphore to mutex conversion
This is the usbatm part of the Arjan, Jes and Ingo
mass semaphore to mutex conversion, reworked to apply on top
of the patches I just sent to you.  This time, with correct
attribution and signed-off lines.

Signed-off-by: Arjan van de Ven <arjan@infradead.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Duncan Sands <baldrick@free.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2006-01-31 17:23:40 -08:00
Duncan Sands 80aae7a17a [PATCH] USBATM: allow isochronous transfer
While the usbatm core has had some support for using isoc urbs
for some time, there was no way for users to turn it on.  While
use of isoc transfer should still be considered experimental, it
now works well enough to let users turn it on.  Minidrivers signal
to the core that they want to use isoc transfer by setting the new
UDSL_USE_ISOC flag.  The speedtch minidriver gets a new module
parameter enable_isoc (defaults to false), plus some logic that
checks for the existence of an isoc receive endpoint (not all
speedtouch modems have one).

Signed-off-by: Duncan Sands <baldrick@free.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2006-01-31 17:23:40 -08:00
Duncan Sands 9a734efec3 [PATCH] USBATM: kzalloc conversion
Convert kmalloc + memset to kzalloc.

Signed-off-by: Duncan Sands <baldrick@free.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2006-01-31 17:23:39 -08:00
Duncan Sands 0dfcd3e444 [PATCH] USBATM: remove .owner
Remove the unused .owner field in struct usbatm_driver.

Signed-off-by: Duncan Sands <baldrick@free.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2006-01-31 17:23:39 -08:00
Duncan Sands 35644b0cce [PATCH] USBATM: add flags field
Have minidrivers and the core signal special requirements
using a flags field in struct usbatm_data.  For the moment
this is only used to replace the need_heavy_init bind
parameter, but there'll be new flags in later patches.

Signed-off-by: Duncan Sands <baldrick@free.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2006-01-31 17:23:39 -08:00
Duncan Sands 0ec3c7e856 [PATCH] USBATM: trivial modifications
Formatting, changes to variable names, comments, log level changes,
printk rate limiting.

Signed-off-by:	Duncan Sands <baldrick@free.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2006-01-31 17:23:39 -08:00
Greg Kroah-Hartman 75318d2d7c [PATCH] USB: remove .owner field from struct usb_driver
It is no longer needed, so let's remove it, saving a bit of memory.

Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2006-01-04 13:48:34 -08:00
Dave Jones d3420ba493 [PATCH] Additional device ID for Conexant AccessRunner USB driver
Reported as working in Fedora bugzilla by Petr.

From: Petr Tuma <petr.tuma@mff.cuni.cz>
Signed-off-by: Dave Jones <davej@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2005-11-29 21:39:22 -08:00
Alan Stern b375a0495f [PATCH] USB: URB_ASYNC_UNLINK flag removed from the kernel
29 July 2005, Cambridge, MA:

This afternoon Alan Stern submitted a patch to remove the URB_ASYNC_UNLINK
flag from the Linux kernel.  Mr. Stern explained, "This flag is a relic
from an earlier, less-well-designed system.  For over a year it hasn't
been used for anything other than printing warning messages."

An anonymous spokesman for the Linux kernel development community
commented, "This is exactly the sort of thing we see happening all the
time.  As the kernel evolves, support for old techniques and old code can
be jettisoned and replaced by newer, better approaches.  Proprietary
operating systems do not have the freedom or flexibility to change so
quickly."

Mr. Stern, a staff member at Harvard University's Rowland Institute who
works on Linux only as a hobby, noted that the patch (labelled as548) did
not update two files, keyspan.c and option.c, in the USB drivers' "serial"
subdirectory.  "Those files need more extensive changes," he remarked.
"They examine the status field of several URBs at times when they're not
supposed to.  That will need to be fixed before the URB_ASYNC_UNLINK flag
is removed."

Greg Kroah-Hartman, the kernel maintainer responsible for overseeing all
of Linux's USB drivers, did not respond to our inquiries or return our
calls.  His only comment was "Applied, thanks."

Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2005-09-08 16:23:04 -07:00
Duncan Sands 322a95bc8e [PATCH] USB ATM: line speed measured in Kb not Kib
Spotted by David Woodhouse.

Signed-off-by: Duncan Sands <baldrick@free.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2005-07-12 11:52:55 -07:00
Duncan Sands 1b0e614652 [PATCH] USB ATM: driver for the Conexant AccessRunner chipset cxacru
Driver for modems based on the Conexant AccessRunner chipset.
Original patch by Josep Comas, much reworked by Roman Kagan.

Signed-off-by: Duncan Sands <baldrick@free.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2005-06-27 14:43:56 -07:00