Signed-off-by: Pavel Roskin <proski@gnu.org>
The reg variable is only used by __raw_writel() and __raw_readl(), which
should guarantee memory access in the right order.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Implementing this callback function will cause mac80211 refrain from
going to powersave state when there are still untransmitted TX frames
in the queues.
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
A panic was observed when the device is failed to resume properly,
and there are no running interfaces. ieee80211_reconfig tries
to restart STA timers on unassociated state.
Cc: stable@kernel.org
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We were uploading different firmwares to the hardware until finding
responding one.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In order to support pre-populating the P1K cache in
iwlwifi hardware for WoWLAN, we need to calculate
the P1K for the current IV32. Allow drivers to get
the P1K for any given IV32 instead of for a given
packet, but keep the packet-based version around as
an inline.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In order to implement GTK rekeying, the device needs
to be able to encrypt frames with the right PN/IV and
check the PN/IV in RX frames. To be able to tell it
about all those counters, we need to be able to get
them from mac80211, this adds the required API.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The current rx->queue value is slightly confusing.
It is set to 16 on non-QoS frames, including data,
and then used for sequence number and PN/IV checks.
Until recently, we had a TKIP IV checking bug that
had been introduced in 2008 to fix a seqno issue.
Before that, we always used TID 0 for checking the
PN or IV on non-QoS packets.
Go back to the old status for PN/IV checks using
the TID 0 counter for non-QoS by splitting up the
rx->queue value into "seqno_idx" and "security_idx"
in order to avoid confusion in the future. They
each have special rules on the value used for non-
QoS data frames.
Since the handling is now unified, also revert the
special TKIP handling from my patch
"mac80211: fix TKIP replay vulnerability".
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
LCN-PHY was found in 14e4:4727 card. It uses LCN/1 and 0x2064/1 radio.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
mac80211 has a defnition of AES_BLOCK_SIZE and
multiple definitions of AES_BLOCK_LEN. Remove
them all and use crypto/aes.h.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Older cores had unique PHY. This is not true anymore for newer ones.
For example core rev 16 can be LP, SSLPN or N (PHY).
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Just like TKIP and CCMP, CMAC has the PN race.
It might not actually be possible to hit it now
since there aren't multiple ACs for management
frames, but fix it anyway.
Also move scratch buffers onto the stack.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since we can process multiple packets at the
same time for different ACs, but the PN is
allocated from a single counter, we need to
use an atomic value there. Use atomic64_t to
make this cheaper on 64-bit platforms, other
platforms will support this through software
emulation, see lib/atomic64.c.
We also need to use an on-stack scratch buf
so that multiple packets won't corrupt each
others scratch buffers.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Our current TKIP code races against itself on TX
since we can process multiple packets at the same
time on different ACs, but they all share the TX
context for TKIP. This can lead to bad IVs etc.
Also, the crypto offload helper code just obtains
the P1K/P2K from the cache, and can update it as
well, but there's no guarantee that packets are
really processed in order.
To fix these issues, first introduce a spinlock
that will protect the IV16/IV32 values in the TX
context. This first step makes sure that we don't
assign the same IV multiple times or get confused
in other ways.
Secondly, change the way the P1K cache works. I
add a field "p1k_iv32" that stores the value of
the IV32 when the P1K was last recomputed, and
if different from the last time, then a new P1K
is recomputed. This can cause the P1K computation
to flip back and forth if packets are processed
out of order. All this also happens under the new
spinlock.
Finally, because there are argument differences,
split up the ieee80211_get_tkip_key() API into
ieee80211_get_tkip_p1k() and ieee80211_get_tkip_p2k()
and give them the correct arguments.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Split tx_queue_count to count per-AC skb's queued, instead of relying on
the skb-queue len. The skb queues used were only valid in STA-mode, as
AP-mode uses per-link queues.
This fixes a major regression in AP-mode, caused by the patch
"wl12xx: implement Tx watermarks per AC". With that patch applied, we
effectively had no regulation of Tx queues in AP-mode. Therefore a
sustained high rate of Tx could cause exhaustion of the skb memory pool.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
The ERTM receive buffer is now handled in a way that does not require
the busy queue and the associated polling code.
Signed-off-by: Mat Martineau <mathewm@codeaurora.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
This change moves most L2CAP ERTM receive buffer handling out of the
L2CAP core and in to the socket code. It's up to the higher layer
(the socket code, in this case) to tell the core when its buffer is
full or has space available. The recv op should always accept
incoming ERTM data or else the connection will go down.
Within the socket layer, an skb that does not fit in the socket
receive buffer will be temporarily stored. When the socket is read
from, that skb will be placed in the receive buffer if possible. Once
adequate buffer space becomes available, the L2CAP core is informed
and the ERTM local busy state is cleared.
Receive buffer management for non-ERTM modes is unchanged.
Signed-off-by: Mat Martineau <mathewm@codeaurora.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
The local busy state is entered and exited based on buffer status in
the socket layer (or other upper layer). This change is in
preparation for general buffer status reports from the socket layer,
which will then be used to change the local busy status.
Signed-off-by: Mat Martineau <mathewm@codeaurora.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Implementing this callback function will cause mac80211 refrain from
going to powersave state when there are still untransmitted TX frames
in the queues.
This would exactly mimic the behaviour of the legacy vendor driver which
also doesn't go in powersave mode if there are still TX frames that are not
transmitted.
This should make powersaving and rt2x00 a better couple.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Sitecom WLA4000 (USB ID 0x0df6:0x0060) is an RT3072 chipset.
Sitecom WLA5000 (USB ID 0x0df6:0x0062) is an RT3572 chipset.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Reported-by: Wim Vander Schelden <wim@fixnum.org>
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently a lot of actions that can be done without the queue's tx lock
being held are done inside the locked area.
Move them out to have a leaner and meaner code that operates while the
tx lock is being held.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The functions that create the tx descriptor structure do not operate on
a queue entry at all. Signal this fact in the code by not providing a
queue entry as a parameter, but the rt2x00 device structure and the skb
directly.
This patch is a preparation for reducing the time a queue is locked for
a tx operation.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The rt2x00 driver gets frequent occurrences of the following error message
when operating under load:
phy0 -> rt2x00queue_write_tx_frame: Error - Arrived at non-free entry in the
non-full queue 2.
This is caused by simultaneous attempts from mac80211 to send a frame via
rt2x00, which are not properly serialized inside rt2x00queue_write_tx_frame,
causing the second frame to fail sending with the above mentioned error
message.
Fix this by introducing a per-queue spinlock to serialize the TX operations
on that queue.
Reported-by: Andreas Hartmann <andihartmann@01019freenet.de>
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We must not init it like clientmode one, it would break device (tested
by Hauke on BCM4718). Add stub hostmode driver for now.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Unlike CCMP, the presence or absence of the QoS
field doesn't change the encryption, only the
TID is used. When no QoS field is present, zero
is used as the TID value. This means that it is
possible for an attacker to take a QoS packet
with TID 0 and replay it as a non-QoS packet.
Unfortunately, mac80211 uses different IVs for
checking the validity of the packet's TKIP IV
when it checks TID 0 and when it checks non-QoS
packets. This means it is vulnerable to this
replay attack.
To fix this, use the same replay counter for
TID 0 and non-QoS packets by overriding the
rx->queue value to 0 if it is 16 (non-QoS).
This is a minimal fix for now. I caused this
issue in
commit 1411f9b531
Author: Johannes Berg <johannes@sipsolutions.net>
Date: Thu Jul 10 10:11:02 2008 +0200
mac80211: fix RX sequence number check
while fixing a sequence number issue (there,
a separate counter needs to be used).
Cc: stable@kernel.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We were not allocating memory for the IEs passed in the scheduled_scan
request and this was causing memory corruption (buffer overflow).
Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The enable_smp parameter is no longer needed. It can be replaced by
checking lmp_host_le_capable.
Signed-off-by: Andre Guedes <andre.guedes@openbossa.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Since we have the extended LMP features properly implemented, we
should check the LMP_HOST_LE bit to know if the host supports LE.
Signed-off-by: Andre Guedes <andre.guedes@openbossa.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Pavel Roskin
Christian Lamparter
Sebastian Andrzej Siewior
Rafał Miłecki
Rajkumar Manoharan
Johannes Berg
John W. Linville
Arik Nemtsov
Mat Martineau
Andre Guedes
Gertjan van Wingerde
Luciano Coelho