Commit Graph

3032 Commits

Author SHA1 Message Date
Linus Torvalds 92a578b064 ACPI and power management updates for 3.19-rc1
This time we have some more new material than we used to have during
 the last couple of development cycles.
 
 The most important part of it to me is the introduction of a unified
 interface for accessing device properties provided by platform
 firmware.  It works with Device Trees and ACPI in a uniform way and
 drivers using it need not worry about where the properties come
 from as long as the platform firmware (either DT or ACPI) makes
 them available.  It covers both devices and "bare" device node
 objects without struct device representation as that turns out to
 be necessary in some cases.  This has been in the works for quite
 a few months (and development cycles) and has been approved by
 all of the relevant maintainers.
 
 On top of that, some drivers are switched over to the new interface
 (at25, leds-gpio, gpio_keys_polled) and some additional changes are
 made to the core GPIO subsystem to allow device drivers to manipulate
 GPIOs in the "canonical" way on platforms that provide GPIO information
 in their ACPI tables, but don't assign names to GPIO lines (in which
 case the driver needs to do that on the basis of what it knows about
 the device in question).  That also has been approved by the GPIO
 core maintainers and the rfkill driver is now going to use it.
 
 Second is support for hardware P-states in the intel_pstate driver.
 It uses CPUID to detect whether or not the feature is supported by
 the processor in which case it will be enabled by default.  However,
 it can be disabled entirely from the kernel command line if necessary.
 
 Next is support for a platform firmware interface based on ACPI
 operation regions used by the PMIC (Power Management Integrated
 Circuit) chips on the Intel Baytrail-T and Baytrail-T-CR platforms.
 That interface is used for manipulating power resources and for
 thermal management: sensor temperature reporting, trip point setting
 and so on.
 
 Also the ACPI core is now going to support the _DEP configuration
 information in a limited way.  Basically, _DEP it supposed to reflect
 off-the-hierarchy dependencies between devices which may be very
 indirect, like when AML for one device accesses locations in an
 operation region handled by another device's driver (usually, the
 device depended on this way is a serial bus or GPIO controller).
 The support added this time is sufficient to make the ACPI battery
 driver work on Asus T100A, but it is general enough to be able to
 cover some other use cases in the future.
 
 Finally, we have a new cpufreq driver for the Loongson1B processor.
 
 In addition to the above, there are fixes and cleanups all over the
 place as usual and a traditional ACPICA update to a recent upstream
 release.
 
 As far as the fixes go, the ACPI LPSS (Low-power Subsystem) driver
 for Intel platforms should be able to handle power management of
 the DMA engine correctly, the cpufreq-dt driver should interact
 with the thermal subsystem in a better way and the ACPI backlight
 driver should handle some more corner cases, among other things.
 
 On top of the ACPICA update there are fixes for race conditions
 in the ACPICA's interrupt handling code which might lead to some
 random and strange looking failures on some systems.
 
 In the cleanups department the most visible part is the series
 of commits targeted at getting rid of the CONFIG_PM_RUNTIME
 configuration option.  That was triggered by a discussion
 regarding the generic power domains code during which we realized
 that trying to support certain combinations of PM config options
 was painful and not really worth it, because nobody would use them
 in production anyway.  For this reason, we decided to make
 CONFIG_PM_SLEEP select CONFIG_PM_RUNTIME and that lead to the
 conclusion that the latter became redundant and CONFIG_PM could
 be used instead of it.  The material here makes that replacement
 in a major part of the tree, but there will be at least one more
 batch of that in the second part of the merge window.
 
 Specifics:
 
  - Support for retrieving device properties information from ACPI
    _DSD device configuration objects and a unified device properties
    interface for device drivers (and subsystems) on top of that.
    As stated above, this works with Device Trees and ACPI and allows
    device drivers to be written in a platform firmware (DT or ACPI)
    agnostic way.  The at25, leds-gpio and gpio_keys_polled drivers
    are now going to use this new interface and the GPIO subsystem
    is additionally modified to allow device drivers to assign names
    to GPIO resources returned by ACPI _CRS objects (in case _DSD is
    not present or does not provide the expected data).  The changes
    in this set are mostly from Mika Westerberg, Rafael J Wysocki,
    Aaron Lu, and Darren Hart with some fixes from others (Fabio Estevam,
    Geert Uytterhoeven).
 
  - Support for Hardware Managed Performance States (HWP) as described
    in Volume 3, section 14.4, of the Intel SDM in the intel_pstate
    driver.  CPUID is used to detect whether or not the feature is
    supported by the processor.  If supported, it will be enabled
    automatically unless the intel_pstate=no_hwp switch is present in
    the kernel command line.  From Dirk Brandewie.
 
  - New Intel Broadwell-H ID for intel_pstate (Dirk Brandewie).
 
  - Support for firmware interface based on ACPI operation regions
    used by the PMIC chips on the Intel Baytrail-T and Baytrail-T-CR
    platforms for power resource control and thermal management
    (Aaron Lu).
 
  - Limited support for retrieving off-the-hierarchy dependencies
    between devices from ACPI _DEP device configuration objects
    and deferred probing support for the ACPI battery driver based
    on the _DEP information to make that driver work on Asus T100A
    (Lan Tianyu).
 
  - New cpufreq driver for the Loongson1B processor (Kelvin Cheung).
 
  - ACPICA update to upstream revision 20141107 which only affects
    tools (Bob Moore).
 
  - Fixes for race conditions in the ACPICA's interrupt handling
    code and in the ACPI code related to system suspend and resume
    (Lv Zheng and Rafael J Wysocki).
 
  - ACPI core fix for an RCU-related issue in the ioremap() regions
    management code that slowed down significantly after CPUs had
    been allowed to enter idle states even if they'd had RCU callbakcs
    queued and triggered some problems in certain proprietary graphics
    driver (and elsewhere).  The fix replaces synchronize_rcu() in
    that code with synchronize_rcu_expedited() which makes the issue
    go away.  From Konstantin Khlebnikov.
 
  - ACPI LPSS (Low-Power Subsystem) driver fix to handle power
    management of the DMA engine included into the LPSS correctly.
    The problem is that the DMA engine doesn't have ACPI PM support
    of its own and it simply is turned off when the last LPSS device
    having ACPI PM support goes into D3cold.  To work around that,
    the PM domain used by the ACPI LPSS driver is redesigned so at
    least one device with ACPI PM support will be on as long as the
    DMA engine is in use.  From Andy Shevchenko.
 
  - ACPI backlight driver fix to avoid using it on "Win8-compatible"
    systems where it doesn't work and where it was used by default by
    mistake (Aaron Lu).
 
  - Assorted minor ACPI core fixes and cleanups from Tomasz Nowicki,
    Sudeep Holla, Huang Rui, Hanjun Guo, Fabian Frederick, and
    Ashwin Chaugule (mostly related to the upcoming ARM64 support).
 
  - Intel RAPL (Running Average Power Limit) power capping driver
    fixes and improvements including new processor IDs (Jacob Pan).
 
  - Generic power domains modification to power up domains after
    attaching devices to them to meet the expectations of device
    drivers and bus types assuming devices to be accessible at
    probe time (Ulf Hansson).
 
  - Preliminary support for controlling device clocks from the
    generic power domains core code and modifications of the
    ARM/shmobile platform to use that feature (Ulf Hansson).
 
  - Assorted minor fixes and cleanups of the generic power
    domains core code (Ulf Hansson, Geert Uytterhoeven).
 
  - Assorted minor fixes and cleanups of the device clocks control
    code in the PM core (Geert Uytterhoeven, Grygorii Strashko).
 
  - Consolidation of device power management Kconfig options by making
    CONFIG_PM_SLEEP select CONFIG_PM_RUNTIME and removing the latter
    which is now redundant (Rafael J Wysocki and Kevin Hilman).  That
    is the first batch of the changes needed for this purpose.
 
  - Core device runtime power management support code cleanup related
    to the execution of callbacks (Andrzej Hajda).
 
  - cpuidle ARM support improvements (Lorenzo Pieralisi).
 
  - cpuidle cleanup related to the CPUIDLE_FLAG_TIME_VALID flag and
    a new MAINTAINERS entry for ARM Exynos cpuidle (Daniel Lezcano and
    Bartlomiej Zolnierkiewicz).
 
  - New cpufreq driver callback (->ready) to be executed when the
    cpufreq core is ready to use a given policy object and cpufreq-dt
    driver modification to use that callback for cooling device
    registration (Viresh Kumar).
 
  - cpufreq core fixes and cleanups (Viresh Kumar, Vince Hsu,
    James Geboski, Tomeu Vizoso).
 
  - Assorted fixes and cleanups in the cpufreq-pcc, intel_pstate,
    cpufreq-dt, pxa2xx cpufreq drivers (Lenny Szubowicz, Ethan Zhao,
    Stefan Wahren, Petr Cvek).
 
  - OPP (Operating Performance Points) framework modification to
    allow OPPs to be removed too and update of a few cpufreq drivers
    (cpufreq-dt, exynos5440, imx6q, cpufreq) to remove OPPs (added
    during initialization) on driver removal (Viresh Kumar).
 
  - Hibernation core fixes and cleanups (Tina Ruchandani and
    Markus Elfring).
 
  - PM Kconfig fix related to CPU power management (Pankaj Dubey).
 
  - cpupower tool fix (Prarit Bhargava).
 
 /
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v2.0.22 (GNU/Linux)
 
 iQIcBAABCAAGBQJUhj6JAAoJEILEb/54YlRxTM4P/j5g5SfqvY0QKsn7sR7MGZ6v
 nsgCBhJAqTw3ocNC7EAs8z9h2GWy1KbKpakKYWAh9Fs1yZoey7tFSlcv/Rgjlp70
 uU5sDQHtpE9mHKiymdsowiQuWgpl962L4k+k8hUslhlvgk1PvVbpajR6OqG8G+pD
 asuIW9eh1APNkLyXmRJ3ZPomzs0VmRdZJ0NEs0lKX9mJskqEvxPIwdaxq3iaJq9B
 Fo0J345zUDcJnxWblDRdHlOigCimglElfN5qJwaC4KpwUKuBvLRKbp4f69+wfT0c
 kYFiR29X5KjJ2kLfP/wKsLyuDCYYXRq3tCia5M1tAqOjZ+UA89H/GDftx/5lntmv
 qUlBa35VfdS1SX4HyApZitOHiLgo+It/hl8Z9bJnhyVw66NxmMQ8JYN2imb8Lhqh
 XCLR7BxLTah82AapLJuQ0ZDHPzZqMPG2veC2vAzRMYzVijict/p4Y2+qBqONltER
 4rs9uRVn+hamX33lCLg8BEN8zqlnT3rJFIgGaKjq/wXHAU/zpE9CjOrKMQcAg9+s
 t51XMNPwypHMAYyGVhEL89ImjXnXxBkLRuquhlmEpvQchIhR+mR3dLsarGn7da44
 WPIQJXzcsojXczcwwfqsJCR4I1FTFyQIW+UNh02GkDRgRovQqo+Jk762U7vQwqH+
 LBdhvVaS1VW4v+FWXEoZ
 =5dox
 -----END PGP SIGNATURE-----

Merge tag 'pm+acpi-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm

Pull ACPI and power management updates from Rafael Wysocki:
 "This time we have some more new material than we used to have during
  the last couple of development cycles.

  The most important part of it to me is the introduction of a unified
  interface for accessing device properties provided by platform
  firmware.  It works with Device Trees and ACPI in a uniform way and
  drivers using it need not worry about where the properties come from
  as long as the platform firmware (either DT or ACPI) makes them
  available.  It covers both devices and "bare" device node objects
  without struct device representation as that turns out to be necessary
  in some cases.  This has been in the works for quite a few months (and
  development cycles) and has been approved by all of the relevant
  maintainers.

  On top of that, some drivers are switched over to the new interface
  (at25, leds-gpio, gpio_keys_polled) and some additional changes are
  made to the core GPIO subsystem to allow device drivers to manipulate
  GPIOs in the "canonical" way on platforms that provide GPIO
  information in their ACPI tables, but don't assign names to GPIO lines
  (in which case the driver needs to do that on the basis of what it
  knows about the device in question).  That also has been approved by
  the GPIO core maintainers and the rfkill driver is now going to use
  it.

  Second is support for hardware P-states in the intel_pstate driver.
  It uses CPUID to detect whether or not the feature is supported by the
  processor in which case it will be enabled by default.  However, it
  can be disabled entirely from the kernel command line if necessary.

  Next is support for a platform firmware interface based on ACPI
  operation regions used by the PMIC (Power Management Integrated
  Circuit) chips on the Intel Baytrail-T and Baytrail-T-CR platforms.
  That interface is used for manipulating power resources and for
  thermal management: sensor temperature reporting, trip point setting
  and so on.

  Also the ACPI core is now going to support the _DEP configuration
  information in a limited way.  Basically, _DEP it supposed to reflect
  off-the-hierarchy dependencies between devices which may be very
  indirect, like when AML for one device accesses locations in an
  operation region handled by another device's driver (usually, the
  device depended on this way is a serial bus or GPIO controller).  The
  support added this time is sufficient to make the ACPI battery driver
  work on Asus T100A, but it is general enough to be able to cover some
  other use cases in the future.

  Finally, we have a new cpufreq driver for the Loongson1B processor.

  In addition to the above, there are fixes and cleanups all over the
  place as usual and a traditional ACPICA update to a recent upstream
  release.

  As far as the fixes go, the ACPI LPSS (Low-power Subsystem) driver for
  Intel platforms should be able to handle power management of the DMA
  engine correctly, the cpufreq-dt driver should interact with the
  thermal subsystem in a better way and the ACPI backlight driver should
  handle some more corner cases, among other things.

  On top of the ACPICA update there are fixes for race conditions in the
  ACPICA's interrupt handling code which might lead to some random and
  strange looking failures on some systems.

  In the cleanups department the most visible part is the series of
  commits targeted at getting rid of the CONFIG_PM_RUNTIME configuration
  option.  That was triggered by a discussion regarding the generic
  power domains code during which we realized that trying to support
  certain combinations of PM config options was painful and not really
  worth it, because nobody would use them in production anyway.  For
  this reason, we decided to make CONFIG_PM_SLEEP select
  CONFIG_PM_RUNTIME and that lead to the conclusion that the latter
  became redundant and CONFIG_PM could be used instead of it.  The
  material here makes that replacement in a major part of the tree, but
  there will be at least one more batch of that in the second part of
  the merge window.

  Specifics:

   - Support for retrieving device properties information from ACPI _DSD
     device configuration objects and a unified device properties
     interface for device drivers (and subsystems) on top of that.  As
     stated above, this works with Device Trees and ACPI and allows
     device drivers to be written in a platform firmware (DT or ACPI)
     agnostic way.  The at25, leds-gpio and gpio_keys_polled drivers are
     now going to use this new interface and the GPIO subsystem is
     additionally modified to allow device drivers to assign names to
     GPIO resources returned by ACPI _CRS objects (in case _DSD is not
     present or does not provide the expected data).  The changes in
     this set are mostly from Mika Westerberg, Rafael J Wysocki, Aaron
     Lu, and Darren Hart with some fixes from others (Fabio Estevam,
     Geert Uytterhoeven).

   - Support for Hardware Managed Performance States (HWP) as described
     in Volume 3, section 14.4, of the Intel SDM in the intel_pstate
     driver.  CPUID is used to detect whether or not the feature is
     supported by the processor.  If supported, it will be enabled
     automatically unless the intel_pstate=no_hwp switch is present in
     the kernel command line.  From Dirk Brandewie.

   - New Intel Broadwell-H ID for intel_pstate (Dirk Brandewie).

   - Support for firmware interface based on ACPI operation regions used
     by the PMIC chips on the Intel Baytrail-T and Baytrail-T-CR
     platforms for power resource control and thermal management (Aaron
     Lu).

   - Limited support for retrieving off-the-hierarchy dependencies
     between devices from ACPI _DEP device configuration objects and
     deferred probing support for the ACPI battery driver based on the
     _DEP information to make that driver work on Asus T100A (Lan
     Tianyu).

   - New cpufreq driver for the Loongson1B processor (Kelvin Cheung).

   - ACPICA update to upstream revision 20141107 which only affects
     tools (Bob Moore).

   - Fixes for race conditions in the ACPICA's interrupt handling code
     and in the ACPI code related to system suspend and resume (Lv Zheng
     and Rafael J Wysocki).

   - ACPI core fix for an RCU-related issue in the ioremap() regions
     management code that slowed down significantly after CPUs had been
     allowed to enter idle states even if they'd had RCU callbakcs
     queued and triggered some problems in certain proprietary graphics
     driver (and elsewhere).  The fix replaces synchronize_rcu() in that
     code with synchronize_rcu_expedited() which makes the issue go
     away.  From Konstantin Khlebnikov.

   - ACPI LPSS (Low-Power Subsystem) driver fix to handle power
     management of the DMA engine included into the LPSS correctly.  The
     problem is that the DMA engine doesn't have ACPI PM support of its
     own and it simply is turned off when the last LPSS device having
     ACPI PM support goes into D3cold.  To work around that, the PM
     domain used by the ACPI LPSS driver is redesigned so at least one
     device with ACPI PM support will be on as long as the DMA engine is
     in use.  From Andy Shevchenko.

   - ACPI backlight driver fix to avoid using it on "Win8-compatible"
     systems where it doesn't work and where it was used by default by
     mistake (Aaron Lu).

   - Assorted minor ACPI core fixes and cleanups from Tomasz Nowicki,
     Sudeep Holla, Huang Rui, Hanjun Guo, Fabian Frederick, and Ashwin
     Chaugule (mostly related to the upcoming ARM64 support).

   - Intel RAPL (Running Average Power Limit) power capping driver fixes
     and improvements including new processor IDs (Jacob Pan).

   - Generic power domains modification to power up domains after
     attaching devices to them to meet the expectations of device
     drivers and bus types assuming devices to be accessible at probe
     time (Ulf Hansson).

   - Preliminary support for controlling device clocks from the generic
     power domains core code and modifications of the ARM/shmobile
     platform to use that feature (Ulf Hansson).

   - Assorted minor fixes and cleanups of the generic power domains core
     code (Ulf Hansson, Geert Uytterhoeven).

   - Assorted minor fixes and cleanups of the device clocks control code
     in the PM core (Geert Uytterhoeven, Grygorii Strashko).

   - Consolidation of device power management Kconfig options by making
     CONFIG_PM_SLEEP select CONFIG_PM_RUNTIME and removing the latter
     which is now redundant (Rafael J Wysocki and Kevin Hilman).  That
     is the first batch of the changes needed for this purpose.

   - Core device runtime power management support code cleanup related
     to the execution of callbacks (Andrzej Hajda).

   - cpuidle ARM support improvements (Lorenzo Pieralisi).

   - cpuidle cleanup related to the CPUIDLE_FLAG_TIME_VALID flag and a
     new MAINTAINERS entry for ARM Exynos cpuidle (Daniel Lezcano and
     Bartlomiej Zolnierkiewicz).

   - New cpufreq driver callback (->ready) to be executed when the
     cpufreq core is ready to use a given policy object and cpufreq-dt
     driver modification to use that callback for cooling device
     registration (Viresh Kumar).

   - cpufreq core fixes and cleanups (Viresh Kumar, Vince Hsu, James
     Geboski, Tomeu Vizoso).

   - Assorted fixes and cleanups in the cpufreq-pcc, intel_pstate,
     cpufreq-dt, pxa2xx cpufreq drivers (Lenny Szubowicz, Ethan Zhao,
     Stefan Wahren, Petr Cvek).

   - OPP (Operating Performance Points) framework modification to allow
     OPPs to be removed too and update of a few cpufreq drivers
     (cpufreq-dt, exynos5440, imx6q, cpufreq) to remove OPPs (added
     during initialization) on driver removal (Viresh Kumar).

   - Hibernation core fixes and cleanups (Tina Ruchandani and Markus
     Elfring).

   - PM Kconfig fix related to CPU power management (Pankaj Dubey).

   - cpupower tool fix (Prarit Bhargava)"

* tag 'pm+acpi-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (120 commits)
  i2c-omap / PM: Drop CONFIG_PM_RUNTIME from i2c-omap.c
  dmaengine / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
  tools: cpupower: fix return checks for sysfs_get_idlestate_count()
  drivers: sh / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
  e1000e / igb / PM: Eliminate CONFIG_PM_RUNTIME
  MMC / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
  MFD / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
  misc / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
  media / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
  input / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
  leds: leds-gpio: Fix multiple instances registration without 'label' property
  iio / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
  hsi / OMAP / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
  i2c-hid / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
  drm / exynos / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
  gpio / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
  hwrandom / exynos / PM: Use CONFIG_PM in #ifdef
  block / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
  USB / PM: Drop CONFIG_PM_RUNTIME from the USB core
  PM: Merge the SET*_RUNTIME_PM_OPS() macros
  ...
2014-12-10 21:17:00 -08:00
Linus Torvalds 3a7dbed7f2 Hi Linus,
Changes to the core:
  - Honour PLATFORM_DEVID_NONE and PLATFORM_DEVID_AUTO dev IDs
 
 Changes to existing drivers:
  - IRQ additions/fixes; axp20x, da9063-core
  - Code simplification; i2c-dln2
  - Regmap additions/fixes; max77693
  - Error checking/handling improvements; dln2, db8500-prcmu
  - Bug fixes; dln2, wm8350-core
  - DT support/documentation; max77693, max77686, tps65217, twl4030-power,
                              gpio-tc3589x
  - Decouple syscon interface from platform devices
  - Use MFD hotplug registration; rtsx_usb, viperboard, hid-sensor-hub
  - Regulator fixups; sec-core
  - Power Management additions/fixes; rts5227, tc6393xb
  - Remove relic/redundant code; ab8500-sysctrl, lpc_sch, max77693-private
  - Clean-up/coding style changes; tps65090
  - Clk additions/fixes; tc6393xb, tc6387xb, t7l66xb
  - Add USB-SPI support; dln2
  - Trivial changes; max14577, arizona-spi, lpc_sch, wm8997-tables, wm5102-tables
                     wm5110-tables, axp20x, atmel-hlcdc, rtsx_pci
 
 New drivers/supported devices:
  - axp288 PMIC support added to axp20x
  - s2mps13 support added to sec-core
  - New support for Diolan DLN-2
  - New support for atmel-hlcdc
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v1
 
 iQIcBAABAgAGBQJUhZDaAAoJEFGvii+H/HdhEY4P+gOlEIU+LYDdKmRjXLp85+ZS
 zrkLQdxvRp61LzzcIMGnduPFAOk8ixb3nRqSJv7P5WQG26I6qoI44zeTF2iSmLTp
 iVLtXRFSlo/lRyWT+2jXwL5iC47PCoJuJajNeM/YEbMERR3sWWAPrATZrQSPoKcZ
 D3qtXge3d+zq2rqpSvNAFNPEC4i9xawwa9GHMte9T/XhaoyVhaK6ITMsh0RK4B0p
 RRc2zy9BGEkuZMu3aC7P/qhfu3uSrxzI6FCHNSbZt/p5aq8klMBGqpK9Tgg4UHUG
 jqAd2lCXHVSVI07CO0YvVUDWV+5NlB1kAeRddohJujV9o5ciaqKCGPKK1Fz0PMxf
 u30t0X4Fb4QCAZVeo1hX9KWKQaQinUzPhANT4Sz0DY1S7arZ6PlJO/obGIys5JCf
 ElJuYNSRqRp6DcaoTHf19DUcxJXnqk73PU3hmsdS4UkweBWDYeagK2gqDwjIhAY6
 DJZ5uqaa829fx/Jj8sUo0EgWZs/Cahf/td7y35fM4bMgU+vHd1xeBvMeltiJ2kuC
 OoZwtyHbV29sMCL2i5VQMkTkLJz49hPOEZolDKUxsV1QEPhi62DRmiHZlKABh3+D
 wzTkTRLfDhlrNedY529/1i3IxIlnzWXfInohe+WadapTFXuISIv6dyAyh9eNKnfd
 ZVf+1NwaCGbZbbPkSBqK
 =dJJd
 -----END PGP SIGNATURE-----

Merge tag 'mfd-for-linus-3.19' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd

Pull MFD updates from Lee Jones:
 "Changes to the core:
   - Honour PLATFORM_DEVID_NONE and PLATFORM_DEVID_AUTO dev IDs

  Changes to existing drivers:
   - IRQ additions/fixes; axp20x, da9063-core
   - Code simplification; i2c-dln2
   - Regmap additions/fixes; max77693
   - Error checking/handling improvements; dln2, db8500-prcmu
   - Bug fixes; dln2, wm8350-core
   - DT support/documentation; max77693, max77686, tps65217, twl4030-power,
                               gpio-tc3589x
   - Decouple syscon interface from platform devices
   - Use MFD hotplug registration; rtsx_usb, viperboard, hid-sensor-hub
   - Regulator fixups; sec-core
   - Power Management additions/fixes; rts5227, tc6393xb
   - Remove relic/redundant code; ab8500-sysctrl, lpc_sch, max77693-private
   - Clean-up/coding style changes; tps65090
   - Clk additions/fixes; tc6393xb, tc6387xb, t7l66xb
   - Add USB-SPI support; dln2
   - Trivial changes; max14577, arizona-spi, lpc_sch, wm8997-tables, wm5102-tables
                      wm5110-tables, axp20x, atmel-hlcdc, rtsx_pci

  New drivers/supported devices:
   - axp288 PMIC support added to axp20x
   - s2mps13 support added to sec-core
   - New support for Diolan DLN-2
   - New support for atmel-hlcdc"

* tag 'mfd-for-linus-3.19' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd: (55 commits)
  mfd: rtsx: Add func to split u32 into register
  mfd: atmel-hlcdc: Add Kconfig option description and name
  mfd: da9063: Get irq base dynamically before registering device
  mfd: max14577: Fix obvious typo in company name in copyright
  mfd: axp20x: Constify axp20x_acpi_match and rid unused warning
  mfd: t7l66xb: prepare/unprepare clocks
  mfd: tc6387xb: prepare/unprepare clocks
  mfd: dln2: add support for USB-SPI module
  mfd: wm5110: Add missing registers for AIF2 channels 3-6
  mfd: tc3589x: get rid of static base
  mfd: arizona: Document HP_CTRL_1L and HP_CTRL_1R registers
  mfd: wm8997: Mark INTERRUPT_STATUS_2_MASK as readable
  mfd: tc6393xb: Prepare/unprepare clocks
  mfd: tps65090: Fix bonkers indenting strategy
  mfd: tc6393xb: Fail ohci suspend if full state restore is required
  mfd: lpc_sch: Don't call mfd_remove_devices()
  mfd: wm8350-core: Fix probable mask then right shift defect
  mfd: ab8500-sysctrl: Drop ab8500_restart
  mfd: db8500-prcmu: Provide sane error path values
  mfd: db8500-prcmu: Check return of devm_ioremap for error
  ...
2014-12-08 20:02:54 -08:00
Rafael J. Wysocki e3d857e1ae Merge branch 'pm-runtime'
* pm-runtime: (25 commits)
  i2c-omap / PM: Drop CONFIG_PM_RUNTIME from i2c-omap.c
  dmaengine / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
  drivers: sh / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
  e1000e / igb / PM: Eliminate CONFIG_PM_RUNTIME
  MMC / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
  MFD / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
  misc / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
  media / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
  input / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
  iio / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
  hsi / OMAP / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
  i2c-hid / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
  drm / exynos / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
  gpio / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
  hwrandom / exynos / PM: Use CONFIG_PM in #ifdef
  block / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
  USB / PM: Drop CONFIG_PM_RUNTIME from the USB core
  PM: Merge the SET*_RUNTIME_PM_OPS() macros
  PM / Kconfig: Do not select PM directly from Kconfig files
  PCI / PM: Drop CONFIG_PM_RUNTIME from the PCI core
  ...
2014-12-08 20:00:44 +01:00
Rafael J. Wysocki 48bb9fe4b3 MFD / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
After commit b2b49ccbdd (PM: Kconfig: Set PM_RUNTIME if PM_SLEEP is
selected) PM_RUNTIME is always set if PM is set, so #ifdef blocks
depending on CONFIG_PM_RUNTIME may now be changed to depend on
CONFIG_PM.

Replace CONFIG_PM_RUNTIME with CONFIG_PM everywhere under
drivers/mfd/.

Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
2014-12-05 03:04:12 +01:00
Boris Brezillon 292aabb1da mfd: atmel-hlcdc: Add Kconfig option description and name
The MFD_ATMEL_HLCDC was first intended to be selected by its sub-devices
but these sub-devices now depends on this option, we thus need to add
a name and a description so that users can see it.

Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
2014-12-01 13:03:30 +00:00
Aaron Lu d8139f6311 ACPI / PMIC: support PMIC operation region for XPower AXP288
The Baytrail-T-CR platform firmware has defined two customized operation
regions for PMIC chip Dollar Cove XPower - one is for power resource
handling and one is for thermal just like the CrystalCove one. This patch
adds support for them on top of the common PMIC opregion region code.

Signed-off-by: Aaron Lu <aaron.lu@intel.com>
Acked-by: Lee Jones <lee.jones@linaro.org> for the MFD part
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2014-11-26 23:32:05 +01:00
Aaron Lu b1eea857d8 ACPI / PMIC: support PMIC operation region for CrystalCove
The Baytrail-T platform firmware has defined two customized operation
regions for PMIC chip Crystal Cove - one is for power resource handling
and one is for thermal: sensor temperature reporting, trip point setting,
etc. This patch adds support for them on top of the existing Crystal Cove
PMIC driver.

The reason to split code into a separate file intel_pmic.c is that there
are more PMIC drivers with ACPI operation region support coming and we can
re-use those code. The intel_pmic_opregion_data structure is created also
for this purpose: when we need to support a new PMIC's operation region,
we just need to fill those callbacks and the two register mapping tables.

Signed-off-by: Aaron Lu <aaron.lu@intel.com>
Acked-by: Lee Jones <lee.jones@linaro.org> for the MFD part
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2014-11-26 23:32:05 +01:00
Dmitry Lavnikevich 439b8bddaa mfd: da9063: Get irq base dynamically before registering device
After registering mfd device with proper irq_base
platform_get_irq_byname() calls will return VIRQ instead of local IRQ.
This fixes da9063 rtc registration issue:
da9063-rtc da9063-rtc: Failed to request ALARM IRQ 1: -22

Signed-off-by: Dmitry Lavnikevich <d.lavnikevich@sam-solutions.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
2014-11-25 16:19:24 +00:00
Krzysztof Kozlowski 2c20f6de95 mfd: max14577: Fix obvious typo in company name in copyright
Fix a typo in name of company in copyright comment.

Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
2014-11-25 16:19:24 +00:00
Lee Jones 0e50e92669 mfd: axp20x: Constify axp20x_acpi_match and rid unused warning
axp20x.c:239:30:
  warning: ‘axp20x_acpi_match’ defined but not used [-Wunused-variable]

Signed-off-by: Lee Jones <lee.jones@linaro.org>
2014-11-25 16:19:23 +00:00
Dmitry Eremin-Solenikov 71d679b84c mfd: t7l66xb: prepare/unprepare clocks
Change clk_enable/disable() calls to clk_prepare_enable() and
clk_disable_unprepare().

Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
2014-11-25 16:18:58 +00:00
Dmitry Eremin-Solenikov 7263bd3925 mfd: tc6387xb: prepare/unprepare clocks
Change clk_enable/disable() calls to clk_prepare_enable() and
clk_disable_unprepare().

Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
2014-11-25 16:18:58 +00:00
Laurentiu Palcu 21cf3318d6 mfd: dln2: add support for USB-SPI module
Signed-off-by: Laurentiu Palcu <laurentiu.palcu@intel.com>
2014-11-25 16:18:57 +00:00
Charles Keepax 783f6fc4ce mfd: wm5110: Add missing registers for AIF2 channels 3-6
When the extra 4 channels were added to AIF2 the necessary frame control
registers were not given defaults and marked readable. This patch fixes
this.

Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
2014-11-25 16:18:56 +00:00
Linus Walleij 90f2d0f7bf mfd: tc3589x: get rid of static base
The TC3589x driver is now a device tree-only driver, so we want
only dynamic IRQs and GPIO numbers from the tc3589x, no static
assignments.

Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2014-11-25 16:18:56 +00:00
Charles Keepax 47958c5ab4 mfd: arizona: Document HP_CTRL_1L and HP_CTRL_1R registers
These registers are documented in the datasheet and used as part of the
extcon driver. Expose them properly through regmap as the datasheet
notes they should be treated as volatile do so.

Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
2014-11-25 16:18:55 +00:00
Charles Keepax e62cace7b6 mfd: wm8997: Mark INTERRUPT_STATUS_2_MASK as readable
Technically this register is not used on wm8997 however the regmap core
requires a continuous block of IRQs. The simplest solution is just to
add the register.

Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
2014-11-25 16:18:54 +00:00
Dmitry Eremin-Solenikov a64ab6b4cd mfd: tc6393xb: Prepare/unprepare clocks
Change clk_enable/disable() calls to clk_prepare_enable() and
clk_disable_unrepapre().

Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
2014-11-25 16:18:54 +00:00
Lee Jones 12849b63a4 mfd: tps65090: Fix bonkers indenting strategy
First spotted pointless (incorrect) indent of 'if (ret)', then double
indentations of a struct attribute 'mask'.  Decided to go through the
whole file and make amendments instead and this is the result.

Signed-off-by: Lee Jones <lee.jones@linaro.org>
2014-11-25 16:18:53 +00:00
Dmitry Eremin-Solenikov 1a5fb99de4 mfd: tc6393xb: Fail ohci suspend if full state restore is required
Some boards with TC6393XB chip require full state restore during system
resume thanks to chip's VCC being cut off during suspend (Sharp SL-6000
tosa is one of them). Failing to do so would result in ohci Oops on
resume due to internal memory contentes being changed. Fail ohci suspend
on tc6393xb is full state restore is required.

Recommended workaround is to unbind tmio-ohci driver before suspend and
rebind it after resume.

Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
2014-11-25 16:18:52 +00:00
Andy Shevchenko bde3e706a6 mfd: lpc_sch: Don't call mfd_remove_devices()
MFD core already cares about failing registration. It will remove successfully
registered devices in case of error. Thus, no need to repeatedly call
mfd_remove_devices().

Fixes: 5829e9b64e (mfd: lpc_sch: Accomodate partial population of the MFD devices)
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
2014-11-25 16:18:52 +00:00
Joe Perches 1753b40f5c mfd: wm8350-core: Fix probable mask then right shift defect
Precedence of & and >> is not the same and is not left to right.
shift has higher precedence and should be done after the mask.

Add parentheses around the mask.

Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
2014-11-25 16:18:51 +00:00
Guenter Roeck 7d082baa34 mfd: ab8500-sysctrl: Drop ab8500_restart
ab8500_restart is not called from anywhere in the kernel, so drop it.

Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
2014-11-25 16:18:50 +00:00
Lee Jones 6bdf891a17 mfd: db8500-prcmu: Provide sane error path values
Also rid superfluous gotos and label.

Cc: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
2014-11-25 16:18:50 +00:00
Pramod Gurav 51a7e02bb6 mfd: db8500-prcmu: Check return of devm_ioremap for error
Error check around return value of devm_ioremap is missing. Add the same
to avoid NULL pointer dereference.

Signed-off-by: Pramod Gurav <pramod.gurav@smartplayin.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
2014-11-25 16:18:49 +00:00
Tony Lindgren 1b9b46d05f mfd: twl4030-power: Fix regression with missing compatible flag
Commit e7cd1d1eb1 ("mfd: twl4030-power: Add generic reset
configuration") accidentally removed the compatible flag for
"ti,twl4030-power" that should be there as documented in the
binding.

If "ti,twl4030-power" only the poweroff configuration is done
by the driver.

Fixes: e7cd1d1eb1 ("mfd: twl4030-power: Add generic reset configuration")
Cc: stable@vger.kernel.org # v3.16+
Reported-by: "Dr. H. Nikolaus Schaller" <hns@goldelico.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
2014-11-25 16:18:48 +00:00
Micky Ching 5cb5d9616a mfd: rtsx: Fix PM suspend for 5227 & 5249
Fix rts5227&5249 failed send buffer cmd after suspend,
PM_CTRL3 should reset before send any buffer cmd after suspend.
Otherwise, buffer cmd will failed, this will lead resume fail.

Signed-off-by: Micky Ching <micky_ching@realsil.com.cn>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
2014-11-25 16:18:48 +00:00
Javier Martinez Canillas 6ce286f182 Revert "mfd: sec-core: Prepare regulators for suspend state to reduce power-consumption"
This reverts commit b7cde7078d
("mfd: sec-core: Prepare regulators for suspend state to reduce power-consumption")

Commit b7cde7078d called regulator_suspend_prepare() to prepare the
regulators for a suspend state. But it did from the device pm suspend
handler while the regulator suspend prepare function iterates over all
regulators and not only the one managed by this device so it doesn't
seems to be correct to call it from within a device driver.

It is better to call the regulator suspend prepare/finish functions
from platform code instead so this patch reverts the mentioned commit.

Suggested-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Reviewed-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
2014-11-25 16:18:47 +00:00
Krzysztof Kozlowski efa3ca414b mfd: max77693: Map charger device to its own of_node
Add a "maxim,max77693-charger" of_compatible to the mfd_cell so the MFD
child device (the charger) will have its own of_node set. This will be
used by the max77693 charger driver in next patches to obtain battery
configuration from DTS.

Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
2014-11-25 16:18:46 +00:00
Will Sheppard 6f467e5f0c mfd: arizona-spi: Add lines after declarations - checkpatch catch
This was found whilst running checkpatch.pl on arizona-spi.

WARNING: Missing a blank line after declarations
+       struct arizona *arizona = spi_get_drvdata(spi);
+       arizona_dev_exit(arizona);

Signed-off-by: Will Sheppard <wsheppard@embedded-bits.co.uk>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
2014-11-25 16:18:45 +00:00
Boris Brezillon 2c86e9fb72 mfd: Add atmel-hlcdc driver
The HLCDC IP available on some Atmel SoCs (i.e. at91sam9n12, at91sam9x5
family or sama5d3 family) exposes 2 subdevices:
- a display controller (controlled by a DRM driver)
- a PWM chip

The MFD device provides a regmap and several clocks (those connected
to this hardware block) to its subdevices.

This way concurrent accesses to the iomem range are handled by the regmap
framework, and each subdevice can safely access HLCDC registers.

Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Tested-by: Anthony Harivel <anthony.harivel@emtrion.de>
Tested-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
2014-11-25 16:18:43 +00:00
Johan Hovold 6e3f62f079 mfd: core: Fix platform-device id generation
Make sure to always honour multi-function devices registered with
PLATFORM_DEVID_NONE (-1) or PLATFORM_DEVID_AUTO (-2) as id base. In this
case it does not make sense to append the cell id to the mfd-id base and
potentially change the requested behaviour.

Specifically this will allow multi-function devices to be registered
with PLATFORM_DEVID_AUTO while still having non-zero cell ids.

Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
2014-11-25 16:18:43 +00:00
Johan Hovold 1ab589c72e mfd: Use mfd_add_hotplug_devices() helper
Use mfd_add_hotplug_devices helper to register the subdevices.

Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
2014-11-25 16:18:42 +00:00
Pankaj Dubey bdb0066df9 mfd: syscon: Decouple syscon interface from platform devices
Currently a syscon entity can be only registered directly through a
platform device that binds to a dedicated syscon driver. However in
certain use cases it is desirable to make a device used with another
driver a syscon interface provider.

For example, certain SoCs (e.g. Exynos) contain system controller
blocks which perform various functions such as power domain control,
CPU power management, low power mode control, but in addition contain
certain IP integration glue, such as various signal masks,
coprocessor power control, etc. In such case, there is a need to have
a dedicated driver for such system controller but also share registers
with other drivers. The latter is where the syscon interface is helpful.

In case of DT based platforms, this patch decouples syscon object from
syscon platform driver, and allows to create syscon objects first time
when it is required by calling of syscon_regmap_lookup_by APIs and keep
a list of such syscon objects along with syscon provider device_nodes
and regmap handles.

For non-DT based platforms, this patch keeps syscon platform driver
structure so that syscon can be probed and such non-DT based drivers
can use syscon_regmap_lookup_by_pdev API and access regmap handles.
Once all users of "syscon_regmap_lookup_by_pdev" migrated to DT based,
we can completely remove platform driver of syscon, and keep only helper
functions to get regmap handles.

Suggested-by: Arnd Bergmann <arnd@arndb.de>
Suggested-by: Tomasz Figa <tomasz.figa@gmail.com>
Tested-by: Vivek Gautam <gautam.vivek@samsung.com>
Tested-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Pankaj Dubey <pankaj.dubey@samsung.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
2014-11-25 16:18:41 +00:00
Jaewon Kim d1bafd78fc mfd: max77693: Add haptic of_compatible in mfd_cell
This patch add haptic of_compatible in order to use the haptic
device driver using Devicetree.

Signed-off-by: Jaewon Kim <jaewon02.kim@samsung.com>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
2014-11-25 16:18:40 +00:00
Jaewon Kim efbf49224a mfd: max77693: Initialize haptic register map
This patch add regmap_haptic initialization to use haptic register map
in haptic device driver.

Signed-off-by: Jaewon Kim <jaewon02.kim@samsung.com>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
2014-11-25 16:18:39 +00:00
Johannes Pointner 11d0d30093 mfd: tps65217: Add compatible string for subdevices
Adds of_compatible strings to mfd_cells for sub devices of the tps65217.

Signed-off-by: Johannes Pointner <johannes.pointner@br-automation.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
2014-11-25 16:18:38 +00:00
Lee Jones a9e2e4733c Immutable branch between MFD, Regulator and Clk, due for v3.19
-----BEGIN PGP SIGNATURE-----
 Version: GnuPG v1
 
 iQIcBAABAgAGBQJUdKaZAAoJEFGvii+H/HdhPj8P/1Jl60LnYPozG0eu6+rNaLDj
 AL8bNLWh0pANQzpYstE4aHDmrEWTArJ37eIet6BrPN/nv/ej2DR7hgK7Eh8h4P1t
 2LtBpxCT3f/Md92iBTLa/bMFm4VuuT/GiOurb1vR9BtTyH1bD8ftmXwhmzHskBuT
 wK0lfdvLEMRI2YIkgnLcuto07kMAIbLAQ4TANWvnHL2XLGd0/aPn68q3jNgwPjgf
 ufi5/eV8y+M/oopYPjU4Mt4W5fOTCZ6yINsp3tkOhPk9G28wJSmAiDkm9bn7KVrz
 Jwy60tpO9Z2+kff62uMjcWvMEvnMcrfQJ3cGm+Si64DuM+s2hmWpA/rXeO+Ep7VX
 jk3aiYXkFmUfgFXz7qMhFEERXu4nwhSGgdbEZWRmG8rcSaS3KnBNDaSvZOOH2mCq
 8iQmMzSMDK6CnW2wIr+2AsrrizPEPrvMOs7GLiUiyXlOjkUSR1XjJ6HlIfXKiMYg
 bWliacyGm3v+K3g41u9ULHNmLi779SlsUrH+Z6NARN5kRKXvsPntDA+8em11euvt
 7h1/wyPpjvJi8Cj5VJzinh4l/9t9O2GNeDuKExuOnaRHoOhzGkFwwMBgUkEdb5lX
 1il7JIXb/MfrwDbd4EZ/G0Ju2icFOfuwCAjad0upBfGkU11zJEa/KozN1ymjq/bD
 whTJLra7D6P0E8DBdS/0
 =WTv4
 -----END PGP SIGNATURE-----

Merge branches 'ib-mfd-gpio-i2c-3.19', 'ib-mfd-iio-3.19' and 'ib-mfd-regulator-v3.19', tag 'ib-mfd-regulator-clk-v3.19' into ibs-for-mfd-merged

Immutable branch between MFD, Regulator and Clk, due for v3.19
2014-11-25 16:18:03 +00:00
Chanwoo Choi 76b9840b24 regulator: s2mps11: Add support S2MPS13 regulator device
This patch adds S2MPS13 regulator device to existing S2MPS11 device driver.
The S2MPS13 has just different number of regulators from S2MPS14.
The S2MPS13 regulator device includes LDO[1-40] and BUCK[1-10].

Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Acked-by: Sangbeom Kim <sbkim73@samsung.com>
Acked-by: Mark Brown <broonie@kernel.org>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
2014-11-25 15:55:06 +00:00
Chanwoo Choi 3bc2ee91a4 mfd: sec-core: Add support for S2MPS13 device
This patch adds the support for Samsung S2MPS13 PMIC device to the sec-core MFD
driver. The S2MPS13 is very similar with existing S2MPS14 and includes PMIC/
RTC/CLOCK devices.

Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Acked-by: Sangbeom Kim <sbkim73@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
2014-11-25 15:55:01 +00:00
Rafael J. Wysocki a26033a1f5 Merge branch 'ib-mfd-iio-3.19' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd into acpi-pmic
Pull MFD changes that the ACPI PMIC changes depend on from Lee Jones.
2014-11-25 02:18:58 +01:00
Grant Likely 66e6a5a1fc Linux 3.18-rc6
-----BEGIN PGP SIGNATURE-----
 Version: GnuPG v1
 
 iQEcBAABAgAGBQJUcmzrAAoJEHm+PkMAQRiGUskH/il9ul71lyyvrA/bRbi0GfUa
 2Ej1Q4Fa/SRzLMiWF8Wy/AlYBbl4/uD3a3XEueK4f9dNguTLZF/rwXTlKKzUeiGg
 zFObbJg3zfa926PQcEV5mc+h71ZkWmbH5CjF6GfYIlj6kjVa5MXF3lSZz27DoAx3
 DjoLKpj1fXQJu1HD7xvUn0r720RgYfic9iKdS69eEYex+Js92WySukogvMG5WAVD
 xuwlJcJgm0YpgNr1t1ij4ekE5XR9jjiE4EXbOZYWcOOd+YXAwZpBrKOgxP0gma3w
 OGwEvmAbzf/3IsGq3dPFYWQ2nfiLA/Qh7y20E19FLKpPBu5ZuTEgFU8VTxh+k+g=
 =rRmA
 -----END PGP SIGNATURE-----

Merge tag 'v3.18-rc6' into devicetree/next

v3.18-rc6 contains an important DT bug fix, c1a2086e2d, "of/selftest:
Fix off-by-one error in removal path" which affects testing of the
overlay patch series. Merge it into the devicetree/next staging branch
so that the overlay patches are applied on top of a known working tree.

Linux 3.18-rc6

Conflicts:
	drivers/of/address.c
2014-11-24 14:50:07 +00:00
Dan Carpenter 2fc2b4846c mfd: dln2: A couple endian fixes
Sparse catches a couple endian bugs.

Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Octavian Purdila <octavian.purdila@intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
2014-11-19 17:12:59 +00:00
Octavian Purdila 00ee7a37fd mfd: dln2: Add a limit check for invalid echo
The echo field in dln2_transfer_complete comes directly from an USB
transfer and we should not trust it is valid.

Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Octavian Purdila <octavian.purdila@intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
2014-11-19 17:12:50 +00:00
Octavian Purdila 7ca2b1c672 mfd: dln2: Fix _dln2_transfer return code
If wait_for_completion_interruptible_timeout returns a positive value
it may be propagated as the return value of _dln2_transfer. This
contradicts the documentation of the function and exposes unnecessary
internals to the callers.

This patch makes sure to set the return value to 0 in that case.

Reported-by: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: Octavian Purdila <octavian.purdila@intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
2014-11-19 17:12:19 +00:00
Jacob Pan ff3bbc5c63 mfd/axp20x: avoid irq numbering collision
IRQ numbers in axp20x devices are defined with high-order bit first
in each IRQ enable/status registers. On Intel platforms it is more
common to number IRQs with least significant bit first. Therefore,
sharing IRQ# between the two is very difficult. Since AXP288 is a
customized PMIC for Intel platform and the amount of shared IRQs are
very small, we use separate IRQ numbering. This also fixes collision
and a duplicate in WBTO interrupt.

e.g. For the 16 interrupts controlled in IRQ enabled registers 1 & 2,
on axp20x for ARM, the PMIC local IRQ numbers and register bits are
mapped as:
IRQ#:  0  1  2  3  4  5  6  7      8  9 10 11 12 13 14 15
---------------------------------------------------------
ARM:   7  6  5  4  3  2  1  0      7  6  5  4  3  2  1  0
Intel: 0  1  2  3  4  5  6  7      0  1  2  3  4  5  6  7

Signed-off-by: Todd Brandt <todd.e.brandt@linux.intel.com>
Signed-off-by: Jacob Pan <jacob.jun.pan@linux.intel.com>
Acked-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
2014-11-18 15:34:13 +00:00
Octavian Purdila 338a128142 mfd: Add support for Diolan DLN-2 devices
This patch implements the USB part of the Diolan USB-I2C/SPI/GPIO
Master Adapter DLN-2. Details about the device can be found here:

https://www.diolan.com/i2c/i2c_interface.html.

Information about the USB protocol can be found in the Programmer's
Reference Manual [1], see section 1.7.

Because the hardware has a single transmit endpoint and a single
receive endpoint the communication between the various DLN2 drivers
and the hardware will be muxed/demuxed by this driver.

Each DLN2 module will be identified by the handle field within the DLN2
message header. If a DLN2 module issues multiple commands in parallel
they will be identified by the echo counter field in the message header.

The DLN2 modules can use the dln2_transfer() function to issue a
command and wait for its response. They can also register a callback
that is going to be called when a specific event id is generated by
the device (e.g. GPIO interrupts). The device uses handle 0 for
sending events.

[1] https://www.diolan.com/downloads/dln-api-manual.pdf

Signed-off-by: Octavian Purdila <octavian.purdila@intel.com>
Reviewed-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
2014-11-10 16:30:05 +00:00
Tony Lindgren 481c7f868c mfd: twl4030-power: Fix poweroff with PM configuration enabled
Commit e7cd1d1eb1 ("mfd: twl4030-power: Add generic reset
configuration") enabled configuring the PM features for twl4030.

This caused poweroff command to fail on devices that have the
BCI charger on twl4030 wired, or have power wired for VBUS.
Instead of powering off, the device reboots. This is because
voltage is detected on charger or VBUS with the default bits
enabled for the power transition registers.

To fix the issue, let's just clear VBUS and CHG bits as we want
poweroff command to keep the system powered off.

Fixes: e7cd1d1eb1 ("mfd: twl4030-power: Add generic reset configuration")
Cc: stable@vger.kernel.org # v3.16+
Reported-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
2014-11-10 15:22:04 +00:00
Krzysztof Kozlowski c0acb8144b mfd: max77693: Fix always masked MUIC interrupts
All interrupts coming from MUIC were ignored because interrupt source
register was masked.

The Maxim 77693 has a "interrupt source" - a separate register and interrupts
which give information about PMIC block triggering the individual
interrupt (charger, topsys, MUIC, flash LED).

By default bootloader could initialize this register to "mask all"
value. In such case (observed on Trats2 board) MUIC interrupts won't be
generated regardless of their mask status. Regmap irq chip was unmasking
individual MUIC interrupts but the source was masked

Before introducing regmap irq chip this interrupt source was unmasked,
read and acked. Reading and acking is not necessary but unmasking is.

Fixes: 342d669c1e ("mfd: max77693: Handle IRQs using regmap")

Cc: <stable@vger.kernel.org>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
2014-11-10 15:22:02 +00:00
Krzysztof Kozlowski 43fc9396ca mfd: max77693: Use proper regmap for handling MUIC interrupts
Interrupts coming from Maxim77693 MUIC block (MicroUSB Interface
Controller) were not handled at all because wrong regmap was used for
MUIC's regmap_irq_chip.

The MUIC component of Maxim 77693 uses different I2C address thus second
regmap is created and used by max77693 extcon driver. The registers for
MUIC interrupts are also in that block and should be handled by that
second regmap.

However the regmap irq chip for MUIC was configured with default regmap
which could not read MUIC registers.

Fixes: 342d669c1e ("mfd: max77693: Handle IRQs using regmap")

Cc: <stable@vger.kernel.org>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
2014-11-10 15:22:01 +00:00
Johan Hovold b668422872 mfd: viperboard: Fix platform-device id collision
Allow more than one viperboard to be connected by registering with
PLATFORM_DEVID_AUTO instead of PLATFORM_DEVID_NONE.

The subdevices are currently registered with PLATFORM_DEVID_NONE, which
will cause a name collision on the platform bus when a second viperboard
is plugged in:

viperboard 1-2.4:1.0: version 0.00 found at bus 001 address 004
------------[ cut here ]------------
WARNING: CPU: 0 PID: 181 at /home/johan/work/omicron/src/linux/fs/sysfs/dir.c:31 sysfs_warn_dup+0x74/0x84()
sysfs: cannot create duplicate filename '/bus/platform/devices/viperboard-gpio'
Modules linked in: i2c_viperboard viperboard netconsole [last unloaded: viperboard]
CPU: 0 PID: 181 Comm: bash Tainted: G        W      3.17.0-rc6 #1
[<c0016bf4>] (unwind_backtrace) from [<c0013860>] (show_stack+0x20/0x24)
[<c0013860>] (show_stack) from [<c04305f8>] (dump_stack+0x24/0x28)
[<c04305f8>] (dump_stack) from [<c0040fb4>] (warn_slowpath_common+0x80/0x98)
[<c0040fb4>] (warn_slowpath_common) from [<c004100c>] (warn_slowpath_fmt+0x40/0x48)
[<c004100c>] (warn_slowpath_fmt) from [<c016f1bc>] (sysfs_warn_dup+0x74/0x84)
[<c016f1bc>] (sysfs_warn_dup) from [<c016f548>] (sysfs_do_create_link_sd.isra.2+0xcc/0xd0)
[<c016f548>] (sysfs_do_create_link_sd.isra.2) from [<c016f588>] (sysfs_create_link+0x3c/0x48)
[<c016f588>] (sysfs_create_link) from [<c02867ec>] (bus_add_device+0x12c/0x1e0)
[<c02867ec>] (bus_add_device) from [<c0284820>] (device_add+0x410/0x584)
[<c0284820>] (device_add) from [<c0289440>] (platform_device_add+0xd8/0x26c)
[<c0289440>] (platform_device_add) from [<c02a5ae4>] (mfd_add_device+0x240/0x344)
[<c02a5ae4>] (mfd_add_device) from [<c02a5ce0>] (mfd_add_devices+0xb8/0x110)
[<c02a5ce0>] (mfd_add_devices) from [<bf00d1c8>] (vprbrd_probe+0x160/0x1b0 [viperboard])
[<bf00d1c8>] (vprbrd_probe [viperboard]) from [<c030c000>] (usb_probe_interface+0x1bc/0x2a8)
[<c030c000>] (usb_probe_interface) from [<c028768c>] (driver_probe_device+0x14c/0x3ac)
[<c028768c>] (driver_probe_device) from [<c02879e4>] (__driver_attach+0xa4/0xa8)
[<c02879e4>] (__driver_attach) from [<c0285698>] (bus_for_each_dev+0x70/0xa4)
[<c0285698>] (bus_for_each_dev) from [<c0287030>] (driver_attach+0x2c/0x30)
[<c0287030>] (driver_attach) from [<c030a288>] (usb_store_new_id+0x170/0x1ac)
[<c030a288>] (usb_store_new_id) from [<c030a2f8>] (new_id_store+0x34/0x3c)
[<c030a2f8>] (new_id_store) from [<c02853ec>] (drv_attr_store+0x30/0x3c)
[<c02853ec>] (drv_attr_store) from [<c016eaa8>] (sysfs_kf_write+0x5c/0x60)
[<c016eaa8>] (sysfs_kf_write) from [<c016dc68>] (kernfs_fop_write+0xd4/0x194)
[<c016dc68>] (kernfs_fop_write) from [<c010fe40>] (vfs_write+0xb4/0x1c0)
[<c010fe40>] (vfs_write) from [<c01104a8>] (SyS_write+0x4c/0xa0)
[<c01104a8>] (SyS_write) from [<c000f900>] (ret_fast_syscall+0x0/0x48)
---[ end trace 98e8603c22d65817 ]---
viperboard 1-2.4:1.0: Failed to add mfd devices to core.
viperboard: probe of 1-2.4:1.0 failed with error -17

Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
2014-11-10 15:22:00 +00:00
Thierry Reding 451be64806 mfd: rtsx: Fix build warnings for !PM
rtsx_pci_power_off() is called only from rtsx_pci_suspend(), which isn't
built when PM is disabled.

Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
2014-11-10 15:21:59 +00:00
Linus Walleij 871c3cf4ea mfd: stmpe: Fix STMPE24xx GPMR LSB
The least significat byte of the GPIO value read register
on the STMPE24xx series is on addres 0xA4 not 0xA5. Correct
against datasheet and tested on the STMPE2401 hardware.

Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
2014-11-10 15:21:58 +00:00
Grant Likely 5063e25a30 of: Eliminate of_allnodes list
The device tree structure is composed of two lists; the 'allnodes' list
which is a singly linked list containing every node in the tree, and the
child->parent structure where each parent node has a singly linked list
of children. All of the data in the allnodes list can be easily
reproduced with the parent-child lists, so of_allnodes is actually
unnecessary. Remove it entirely which saves a bit of memory and
simplifies the data structure quite a lot.

Signed-off-by: Grant Likely <grant.likely@linaro.org>
Cc: Rob Herring <robh@kernel.org>
Cc: Gaurav Minocha <gaurav.minocha.os@gmail.com>
Cc: Pantelis Antoniou <pantelis@pantelis.antoniou@konsulko.com>
2014-11-04 13:29:38 +00:00
Wolfram Sang 78a835416a mfd: drop owner assignment from platform_drivers
A platform_driver does not need to set an owner, it will be populated by the
driver core.

Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2014-10-20 16:20:53 +02:00
Linus Torvalds fcc3a5d277 Changes to existing drivers:
- DT clean-ups in da9055-core, max14577, rn5t618, arizona, hi6421, stmpe, twl4030
   - Export symbols for use in modules in max14577
   - Plenty of static code analysis/Coccinelle fixes throughout the SS
   - Regmap clean-ups in arizona, wm5102, wm5110, da9052, tps65217, rk808
   - Remove unused/duplicate code in da9052, 88pm860x, ti_ssp, lpc_sch, arizona
   - Bug fixes in ti_am335x_tscadc, da9052, ti_am335x_tscadc, rtsx_pcr
   - IRQ fixups in arizona, stmpe, max14577
   - Regulator related changes in axp20x
   - Pass DMA coherency information from parent => child in MFD core
   - Rename DT document files for consistency
   - Add ACPI support to the MFD core
   - Add Andreas Werner to MAINTAINERS for MEN F21BMC
 
 New drivers/supported devices:
   - New driver for MEN 14F021P00 Board Management Controller
   - New driver for Ricoh RN5T618 PMIC
   - New driver for Rockchip RK808
   - New driver for HiSilicon Hi6421 PMIC
   - New driver for Qualcomm SPMI PMICs
   - Add support for Intel Braswell in lpc_ich
   - Add support for Intel 9 Series PCH in lpc_ich
   - Add support for Intel Quark ILB in lpc_sch
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v1
 
 iQIcBAABAgAGBQJUMvv5AAoJEFGvii+H/Hdhq90P/3a7ed9Gc4SatQNJ8u68e8M+
 lllGPWXVKnbCR8yc/kCALBpNYUcyPzTp5u1l/ozwEgRDgCzNAvYC2h/aflpPjWSu
 5q1rE7V8Cz/hUxXU/fcEMcnJYiqdaRowgdFtUM+ClLQReOkmwQhWID+hLvTlCUIN
 6MkXCsAl6vrzBEtbKtlR5+6VDQ3Q84gqN2SadpxS+yQwIfGrq1ZWYATaPhdSNGR9
 4bde6YwAqgttQDHyHw0dsd9VtJ53KVk13QkHIHW6S6uPOaZSIvtt4noDUtghDUA1
 tN7d5e5x1Rm8lPREQ4PxMKqHJoRxGfYyAosqXlt3XA1wbjgOgN35nev3gqrbfho5
 eHIWfFJgPDOOwTRVT1drTOVSoxecsbrQq1YB7ChdnfREQbpFiwKhBIxjQKEpQNrI
 OjxXp4ngXwiz31Hvq+44Z6MEVVRCTXgAuBf9/cd8GkF772H7nKmT+wH1QvF+6BRG
 52qEwugTiINo3O+5g1xuDFjFWZ5GWrwUQuRHss13A0cgo+EUJKM6caH+375T7jIT
 vH+2hg0XrqAlWPqcPd1Ma9TVKqI6RJdF0XOk7YP+PcPRvN+SoW/TAGFpzfDHCd+K
 dj3/10nJZUi4CKz6PRcTxKFFpgYjsEGwhYHRWLtH+MXg3UcCyoqTrvfpkGh+hq37
 H9rkW3cNzeyHSAaeKtnk
 =xxsZ
 -----END PGP SIGNATURE-----

Merge tag 'mfd-for-linus-3.18' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd

Pull MFD updates from Lee Jones:
 "Changes to existing drivers:
  - DT clean-ups in da9055-core, max14577, rn5t618, arizona, hi6421, stmpe, twl4030
  - Export symbols for use in modules in max14577
  - Plenty of static code analysis/Coccinelle fixes throughout the SS
  - Regmap clean-ups in arizona, wm5102, wm5110, da9052, tps65217, rk808
  - Remove unused/duplicate code in da9052, 88pm860x, ti_ssp, lpc_sch, arizona
  - Bug fixes in ti_am335x_tscadc, da9052, ti_am335x_tscadc, rtsx_pcr
  - IRQ fixups in arizona, stmpe, max14577
  - Regulator related changes in axp20x
  - Pass DMA coherency information from parent => child in MFD core
  - Rename DT document files for consistency
  - Add ACPI support to the MFD core
  - Add Andreas Werner to MAINTAINERS for MEN F21BMC

 New drivers/supported devices:
  - New driver for MEN 14F021P00 Board Management Controller
  - New driver for Ricoh RN5T618 PMIC
  - New driver for Rockchip RK808
  - New driver for HiSilicon Hi6421 PMIC
  - New driver for Qualcomm SPMI PMICs
  - Add support for Intel Braswell in lpc_ich
  - Add support for Intel 9 Series PCH in lpc_ich
  - Add support for Intel Quark ILB in lpc_sch"

[ Delayed to after the poweer/reset pull due to Kconfig problems with
  recursive Kconfig select/depends-on chains.   - Linus ]

* tag 'mfd-for-linus-3.18' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd: (79 commits)
  mfd: cros_ec: wait for completion of commands that return IN_PROGRESS
  i2c: i2c-cros-ec-tunnel: Set retries to 3
  mfd: cros_ec: move locking into cros_ec_cmd_xfer
  mfd: cros_ec: stop calling ->cmd_xfer() directly
  mfd: cros_ec: Delay for 50ms when we see EC_CMD_REBOOT_EC
  MAINTAINERS: Adds Andreas Werner to maintainers list for MEN F21BMC
  mfd: arizona: Correct mask to allow setting micbias external cap
  mfd: Add ACPI support
  Revert "mfd: wm5102: Manually apply register patch"
  mfd: ti_am335x_tscadc: Update logic in CTRL register for 5-wire TS
  mfd: dt-bindings: atmel-gpbr: Rename doc file to conform to naming convention
  mfd: dt-bindings: qcom-pm8xxx: Rename doc file to conform to naming convention
  mfd: Inherit coherent_dma_mask from parent device
  mfd: Document DT bindings for Qualcomm SPMI PMICs
  mfd: Add support for Qualcomm SPMI PMICs
  mfd: dt-bindings: pm8xxx: Add new compatible string
  mfd: axp209x: Drop the parent supplies field
  mfd: twl4030-power: Use 'ti,system-power-controller' as alternative way to support system power off
  mfd: dt-bindings: twl4030-power: Use the standard property to mark power control
  mfd: syscon: Add Atmel GPBR DT bindings documention
  ...
2014-10-15 06:58:16 +02:00
Linus Torvalds 50fa86172b power supply and reset changes for the v3.18 series
- Initial support for the following chips
   * max77836 (charger)
   * max14577 (charger)
   * bq27742 (battery gauge)
   * ltc2952 (poweroff)
   * stih416 (restart)
   * syscon-reboot (restart)
   * gpio-restart (restart)
  - cleanup of power supply core
  - misc. fixes in power supply and reset drivers
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v1
 
 iQIcBAABCgAGBQJUOWD7AAoJENju1/PIO/qaj5QP/AtbG96NRpX6Ou8W+qulhSbe
 npTKItRMERZhV+lJUAdmLxQq8Cy6I5Cobdj140oIM6HIKZ7Dh6jChxd2t+RCLsO0
 Y16VMq45L9E/mQuVCLqSSNCPKrRjbF7hW+8gpym/Yc846o3Fv8nhTQzkWxCsVrDR
 rNerRnrUyvKpqRpCN88u4ZuOHjm/146nZtTsAzvL8nGnQBZFJHv4eu7D5nwSN0QS
 FrLiI/mE7h1KFcdK5LrZf51IfEP9w4RVV3vs1wEuP0iPS5dguv2dNzXXVZa5eD/2
 AYSSouVKkgdwryLAvIIaDLD405UYl5Xgt5J6d+QKXxm2+eeZMEY36+PEK5WtRtBX
 CykzO2BgvxyOdz2HU9D8irR1Li71jVSWwQITMJ6bQsbKEQAhltmkmsTOxtqB+ekd
 254rKcKWTqllmEhg1LR8PCidf8OZNEcKzXi4XmQdQIcKNF9tvdTXP5c0/FzuIAlQ
 tqWZW1kQK6/TTfx+XxeeszJWY5VknIaka2Bi83pOZYtu94CtUFBdEVkpaYmC433+
 qLOto7VMy+AKYViTJJDDEnSEFiLNZz/zF+SUDf+YB1RelULSF3zC8CbDcZQa5fNm
 4qTU1fl2gGrIZ1jDPPihm6xP8r9WkeuQWEytG2UJZoa+l4XmzfLHBUUDVo0zqTd3
 txfmKca8Y3GhXGwINi1m
 =sj9S
 -----END PGP SIGNATURE-----

Merge tag 'for-v3.18' of git://git.infradead.org/battery-2.6

Pull power supply and reset updates from Sebastian Reichel:
 - Initial support for the following chips
   * max77836 (charger)
   * max14577 (charger)
   * bq27742 (battery gauge)
   * ltc2952 (poweroff)
   * stih416 (restart)
   * syscon-reboot (restart)
   * gpio-restart (restart)
 - cleanup of power supply core
 - misc fixes in power supply and reset drivers

* tag 'for-v3.18' of git://git.infradead.org/battery-2.6: (48 commits)
  power: ab8500_fg: Fix build warning
  Documentation: charger: max14577: Update the date of introducing ABI
  power: reset: corrections for simple syscon reboot driver
  Documentation: power: reset: Add documentation for generic SYSCON reboot driver
  power: reset: Add generic SYSCON register mapped reset
  bq27x00_battery: Fix flag reading for bq27742
  power: reset: use restart_notifier mechanism for msm-poweroff
  power: Add simple gpio-restart driver
  power: reset: st: Provide DT bindings for ST's Power Reset driver
  power: reset: Add restart functionality for STiH41x platforms
  power: charger-manager: Fix NULL pointer exception with missing cm-fuel-gauge
  power: max14577: Fix circular config SYSFS dependency
  power: gpio-charger: do not use gpio value directly
  power: max8925: Use of_get_child_by_name
  power: max8925: Fix NULL ptr dereference on memory allocation failure
  bq27x00_battery: Add support to bq27742
  Documentation: charger: max14577: Document exported sysfs entry
  devicetree: mfd: max14577: Add device tree bindings document
  power: max17040: Add ID for MAX77836 Fuel Gauge block
  charger: max14577: Configure battery-dependent settings from DTS and sysfs
  ...

Conflicts:
	drivers/power/reset/Kconfig
	drivers/power/reset/Makefile
2014-10-15 06:56:23 +02:00
Linus Torvalds 40c43269cf New driver for menf21bmc.
Convert k10temp, smsc47b397, da9052, da9055 to new hwmon API.
 Register ntc_thermistor driver with thermal subsystem.
 Add support for F15h M60h to k10temp driver.
 Add driver for MEN14F021P00 BMC HWMON driver; this required a merge
 with tag mfd-hwmon-leds-watchdog-v3.18.
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v1
 
 iQIcBAABAgAGBQJUNZQwAAoJEMsfJm/On5mBxZEQAIf555P39+4fkRIrf3oYUuC2
 q1tXNP0u8Z74eDFfwYYobt+NCJG5KW3H3kFaO5WCTjySfVwjUin9Fc6DkLl2m3U+
 4FfH/2rO1y1upVRQemLAhe7BAYJAzABuNFWbLqqbGbZytyf5sHzhP52vjJ5VNmvr
 5zcn/sGJdB5M9tj3isvfrac0itNu+D7K3qxknk4wI5gb6YzKg+uovXscPVx4Xa7w
 eHKXJWITtBAZdD5bDV5YAzlTR15ASG3h+yyV7G5rKgslYyCMuRfIDm8Rl5zzHUmq
 DjLwwib469NMii6CjdC7kEpYOgJ2ZxK/2XQ5IAeGax8GLdIHB6lhp3GrXIzzRwiW
 5mtsMdRB7y41p050rIXN7AIXGVqSvtZtKf0r8w1p5YElat/wtX9gv0lGTgOq4sSa
 0SOE7E6W0cfe75dYgJP/6HIkuZZ7PweBelQYDfWrN00u/rdIcwC2nRnW/nDbctkr
 TmQLiS0ql2mXPWXD+Lk9v3bUALuYOPuQpX2aARj7en7jeBagP6KX0d70GaoAEzGk
 Gw6z4X4gI3TasuIck4LZx3kaiijEnDOgnIaEQah4b3k7ABEiuOYVBBpnWvqECaSD
 p9/lwFAs2POCsYSuADiclzxH6FLCMRJLE2V7dgMun9uK60o+0pGUqBL1PG/5/w+r
 jGdB/75PCOEn3Y/VlfZg
 =vI5p
 -----END PGP SIGNATURE-----

Merge tag 'hwmon-for-linus-v3.18' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging

Pull hwmon updates from Guenter Roeck:
 - new driver for menf21bmc.
 - convert k10temp, smsc47b397, da9052, da9055 to new hwmon API.
 - register ntc_thermistor driver with thermal subsystem.
 - add support for F15h M60h to k10temp driver.
 - add driver for MEN14F021P00 BMC HWMON driver; this required a merge
   with tag mfd-hwmon-leds-watchdog-v3.18

* tag 'hwmon-for-linus-v3.18' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
  hwmon: (ab8500) Call kernel_power_off instead of pm_power_off
  hwmon: (menf21bmc) Introduce MEN14F021P00 BMC HWMON driver
  leds: leds-menf21bmc: Introduce MEN 14F021P00 BMC LED driver
  watchdog: menf21bmc_wdt: Introduce MEN 14F021P00 BMC Watchdog driver
  mfd: menf21bmc: Introduce MEN 14F021P00 BMC MFD Core driver
  hwmon: (ntc_thermistor) Add ntc thermistor to thermal subsystem as a sensor.
  hwmon: (smsc47b397) Convert to devm_hwmon_device_register_with_groups
  MAINTAINERS: add entry for the PWM fan driver
  hwmon: (k10temp) Convert to devm_hwmon_device_register_with_groups
  hwmon: (k10temp) Add support for F15h M60h
  hwmon: (da9052) Convert to devm_hwmon_device_register_with_groups
  hwmon: (da9055) Convert to devm_hwmon_device_register_with_groups
  hwmon: (ads1015) Use of_property_read_u32 at appropriate places
2014-10-10 16:40:14 -04:00
Linus Torvalds ea584595fc This is the bulk of GPIO changes for the v3.18 development
cycle:
 
 - Increase the default ARCH_NR_GPIO from 256 to 512. This
   was done to avoid having a custom <asm/gpio.h> header for
   the x86 architecture - GPIO is custom and complicated
   enough as it is already! We want to move to a radix to
   store the descriptors going forward, and finally get rid
   of this fixed array size altogether.
 
 - Endgame patching of the gpio_remove() semantics initiated
   by Abdoulaye Berthe. It is not accepted by the system that
   the removal of a GPIO chip fails during e.g. reboot or
   shutdown, and therefore the return value has now painfully
   been refactored away. For special cases like GPIO expanders
   on a hot-pluggable bus like USB, we may later add some
   gpiochip_try_remove() call, but for the cases we have now,
   return values are moot.
 
 - Some incremental refactoring of the gpiolib core and ACPI
   GPIO library for more descriptor usage.
 
 - Refactor the chained IRQ handler set-up method to handle
   also threaded, nested interrupts and set up the parent IRQ
   correctly. Switch STMPE and TC3589x drivers to use this
   registration method.
 
 - Add a .irq_not_threaded flag to the struct gpio_chip, so
   that also GPIO expanders that block but are still not
   using threaded IRQ handlers.
 
 - New drivers for the ARM64 X-Gene SoC GPIO controller.
 
 - The syscon GPIO driver has been improved to handle the
   "DSP GPIO" found on the TI Keystone 2 SoC:s.
 
 - ADNP driver switched to use gpiolib irqchip helpers.
 
 - Refactor the DWAPB driver to support being instantiated
   from and MFD cell (platform device).
 
 - Incremental feature improvement in the Zynq, MCP23S08,
   DWAPB, OMAP, Xilinx and Crystalcove drivers.
 
 - Various minor fixes.
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v1
 
 iQIcBAABAgAGBQJUNOr0AAoJEEEQszewGV1z9toP/2ISXRnsi3+jlqVmEGm/y6EA
 PPwJOiYnOhZR2/fTCHIF0PNbIi9pw7xKnzxttYCu4uCz7geHX+FfTwUZ2/KWMfqi
 ZJ9kEoOVVKzKjmL/m2a2tO4IRSBHqJ8dF3yvaNjS3AL7EDfG6F5STErQurdLEynK
 SeJZ2OwM/vRFCac6F7oDlqAUTu3xYGbVD8+zI0H0V/ReocosFlEwcbl2S8ctDWUd
 h98M+gY+A8rxkvVMnmQ/k7rUTme/glDQ3z5xVx+uHbS2/a5M1jSM/71cXE6YnSrR
 it0CK7CHomq2RzHsKf7oH7GD4kFkukMwFKeMoqz75JWz3352VZPTF53chCIqRSgO
 hrgGwZ7WF6pUUUhsn1ZdZsnBPA2Fou2uwslyLSAiE+OYEH2/NSVIOUcorjQcWqU/
 0Kix5yb8X1ZzRMhR+TVrTD5V0jguqp2buXq+0P2XlU6MoO2vy7iNf2eXvPg8sF8C
 anjTCKgmkzy7eyT2uzfDaNZAyfSBKb1TiKiR9zA0SRChJkCi1ErJEXDGeHiptvSA
 +D2k68Ils2LqsvdrnEd2XvVFMllh0iq7b+16o7D+Els0WRbnHpfYCaqfOuF5F4U0
 SmeyI0ruawNDc5e9EBKXstt0/R9AMOetyTcTu29U2ZVo90zGaT1ofT8+R1jJ0kGa
 bPARJZrgecgv1E9Qnnnd
 =8InA
 -----END PGP SIGNATURE-----

Merge tag 'gpio-v3.18-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio

Pull GPIO changes from Linus Walleij:
 "This is the bulk of GPIO changes for the v3.18 development cycle:

   - Increase the default ARCH_NR_GPIO from 256 to 512.  This was done
     to avoid having a custom <asm/gpio.h> header for the x86
     architecture - GPIO is custom and complicated enough as it is
     already! We want to move to a radix to store the descriptors going
     forward, and finally get rid of this fixed array size altogether.

   - Endgame patching of the gpio_remove() semantics initiated by
     Abdoulaye Berthe.  It is not accepted by the system that the
     removal of a GPIO chip fails during eg reboot or shutdown, and
     therefore the return value has now painfully been refactored away.
     For special cases like GPIO expanders on a hot-pluggable bus like
     USB, we may later add some gpiochip_try_remove() call, but for the
     cases we have now, return values are moot.

   - Some incremental refactoring of the gpiolib core and ACPI GPIO
     library for more descriptor usage.

   - Refactor the chained IRQ handler set-up method to handle also
     threaded, nested interrupts and set up the parent IRQ correctly.
     Switch STMPE and TC3589x drivers to use this registration method.

   - Add a .irq_not_threaded flag to the struct gpio_chip, so that also
     GPIO expanders that block but are still not using threaded IRQ
     handlers.

   - New drivers for the ARM64 X-Gene SoC GPIO controller.

   - The syscon GPIO driver has been improved to handle the "DSP GPIO"
     found on the TI Keystone 2 SoC:s.

   - ADNP driver switched to use gpiolib irqchip helpers.

   - Refactor the DWAPB driver to support being instantiated from and
     MFD cell (platform device).

   - Incremental feature improvement in the Zynq, MCP23S08, DWAPB, OMAP,
     Xilinx and Crystalcove drivers.

   - Various minor fixes"

* tag 'gpio-v3.18-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (52 commits)
  gpio: pch: Build context save/restore only for PM
  pinctrl: abx500: get rid of unused variable
  gpio: ks8695: fix 'else should follow close brace '}''
  gpio: stmpe: add verbose debug code
  gpio: stmpe: fix up interrupt enable logic
  gpio: staticize xway_stp_init()
  gpio: handle also nested irqchips in the chained handler set-up
  gpio: set parent irq on chained handlers
  gpiolib: irqchip: use irq_find_mapping while removing irqchip
  gpio: crystalcove: support virtual GPIO
  pinctrl: bcm281xx: make Kconfig dependency more strict
  gpio: kona: enable only on BCM_MOBILE or for compile testing
  gpio, bcm-kona, LLVMLinux: Remove use of __initconst
  gpio: Fix ngpio in gpio-xilinx driver
  gpio: dwapb: fix pointer to integer cast
  gpio: xgene: Remove unneeded #ifdef CONFIG_OF guard
  gpio: xgene: Remove unneeded forward declation for struct xgene_gpio
  gpio: xgene: Fix missing spin_lock_init()
  gpio: ks8695: fix switch case indentation
  gpiolib: add irq_not_threaded flag to gpio_chip
  ...
2014-10-09 14:58:15 -04:00
Jacob Pan af7e906954 mfd: axp20x: Extend axp20x to support axp288 pmic
X-Powers AXP288 is a customized PMIC for Intel Baytrail-CR platforms. Similar
to AXP202/209, AXP288 comes with USB charger, more LDO and BUCK channels, and
AD converters. It also provides extended status and interrupt reporting
capabilities than the devices currently supported in axp20x.c.

In addition to feature extension, this patch also adds ACPI binding for
enumeration.

This consolidated driver should support more X-Powers' PMICs in both device
tree and ACPI enumerated platforms.

Signed-off-by: Jacob Pan <jacob.jun.pan@linux.intel.com>
Reviewed-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
2014-10-07 09:30:05 +01:00
Andrew Bresticker d86c21fd31 mfd: cros_ec: wait for completion of commands that return IN_PROGRESS
When an EC command returns EC_RES_IN_PROGRESS, we need to query
the state of the EC until it indicates that it is no longer busy.
Do this in cros_ec_cmd_xfer() under the EC's mutex so that other
commands (e.g. keyboard, I2C passtru) aren't issued to the EC while
it is working on the in-progress command.

The 10 milliseconds delay and the number of retries are the values
that were used by the flashrom tool when retrying commands.

Signed-off-by: Andrew Bresticker <abrestic@chromium.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
2014-10-06 21:30:16 +01:00
Andrew Bresticker 63427530fa mfd: cros_ec: move locking into cros_ec_cmd_xfer
Now that there's a central cros_ec_cmd_xfer(), move the locking
out of the SPI driver.

Signed-off-by: Andrew Bresticker <abrestic@chromium.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Reviewed-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
2014-10-06 21:29:50 +01:00
Andrew Bresticker a6551a76ff mfd: cros_ec: stop calling ->cmd_xfer() directly
Instead of having users of the ChromeOS EC call the interface-specific
cmd_xfer() callback directly, introduce a central cros_ec_cmd_xfer()
to use instead.  This will allow us to put all the locking and retry
logic in one place instead of duplicating it across the different
drivers.

Signed-off-by: Andrew Bresticker <abrestic@chromium.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Reviewed-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
2014-10-06 21:29:07 +01:00
Doug Anderson 659e142be0 mfd: cros_ec: Delay for 50ms when we see EC_CMD_REBOOT_EC
If someone sends a EC_CMD_REBOOT_EC to the EC, the EC will likely be
unresponsive for quite a while.  Add a delay to the end of the command
to prevent random failures of future commands.

NOTES:
* This could be optimized a bit by simply delaying the next command
  sent, but EC_CMD_REBOOT_EC is such a rare command that the extra
  complexity doesn't seem worth it.
* This is a bit of an "ugly hack" since the SPI driver is effectively
  snooping on the communication and making a lot of assumptions.  It
  would be nice to architect in some better solution long term.
* This same logic probably needs to be applied to the i2c driver.

Signed-off-by: Doug Anderson <dianders@chromium.org>
Reviewed-by: Randall Spangler <rspangler@chromium.org>
Reviewed-by: Vadim Bendebury <vbendeb@chromium.org>
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
2014-10-06 21:28:48 +01:00
Charles Keepax 71d134b9fa mfd: arizona: Correct mask to allow setting micbias external cap
Currently the mask for the external capacitor bit is missing when
writing the MICBIAS config meaning it will never be set this patch fixes
this.

Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
2014-09-26 08:24:05 +01:00
Mika Westerberg 6ab3430129 mfd: Add ACPI support
If an MFD device is backed by ACPI namespace, we should allow subdevice
drivers to access their corresponding ACPI companion devices through normal
means (e.g using ACPI_COMPANION()).

This patch adds such support to the MFD core. If the MFD parent device
does not specify any ACPI _HID/_CID for the child device, the child
device will share the parent ACPI companion device. Otherwise the child
device will be assigned with the corresponding ACPI companion, if found
in the namespace below the parent.

Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Darren Hart <dvhart@linux.intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
2014-09-26 08:24:05 +01:00
Charles Keepax 7be180cc7a Revert "mfd: wm5102: Manually apply register patch"
This reverts commit d9d03496f6.

It seems this commit was applied twice, once through ASoC and once
through MFD:

commit 4c9bb8bc35
mfd: wm5102: Manually apply register patch

commit d9d03496f6
mfd: wm5102: Manually apply register patch

This has lead to a small piece of duplicate code. It is harmless hence
how it has gone unoticed for so long. This patch reverts one of the two
commits removing the unneeded code.

Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
2014-09-26 08:24:04 +01:00
Jeff Lance f0933a60d1 mfd: ti_am335x_tscadc: Update logic in CTRL register for 5-wire TS
The logic in AFE_Pen_Ctrl bitmask in the CTRL register is different for five
wire versus four or eight wire touschscreens. This patch should fix this for
five-wire touch screens. There should be no change needed here for four and
eight wire tousch screens.

Signed-off-by: Jeff Lance <j-lance1@ti.com>
[bigeasy: keep the change mfd only]
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
2014-09-26 08:24:03 +01:00
Boris BREZILLON 4f08df1b06 mfd: Inherit coherent_dma_mask from parent device
dma_mask and dma_parms are already inherited from the parent device but
dma_coherent_mask was left uninitialized (set to zero thanks to kzalloc).
Set sub-device coherent_dma_mask to its parent value to simplify
sub-drivers making use of dma coherent helper functions (those drivers
currently have to explicitly set the dma coherent mask using
dma_set_coherent_mask function).

Signed-off-by: Boris BREZILLON <boris.brezillon@free-electrons.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
2014-09-26 08:24:01 +01:00
Josh Cartwright c3a973a770 mfd: Add support for Qualcomm SPMI PMICs
The Qualcomm SPMI PMIC chips are components used with the
Snapdragon 800 series SoC family.  This driver exists
largely as a glue mfd component, it exists to be an owner
of an SPMI regmap for children devices described in
device tree.

Signed-off-by: Josh Cartwright <joshc@codeaurora.org>
Signed-off-by: Stanimir Varbanov <svarbanov@mm-sol.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
2014-09-26 08:24:00 +01:00
Maxime Ripard 6e6240a449 mfd: axp209x: Drop the parent supplies field
Now that the regulator code get its parent supplies purely from the DT, we can
drop the parent supplies resources in the MFD driver.

Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
2014-09-26 08:23:58 +01:00
Nishanth Menon fecc4452b9 mfd: twl4030-power: Use 'ti,system-power-controller' as alternative way to support system power off
ti,system-power-controller is more or less the standard way of
indicating that the PMIC is the system wide power controller and hence
may be used to switch off the system. Almost ALL TI PMIC drivers and
many Maxim PMIC drivers follow the same style.

So support 'ti,system-power-controller' in addition to the usual
'ti,use_poweroff' to indicate that the PMIC instance has control for
switching off the system.

Signed-off-by: Nishanth Menon <nm@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
2014-09-26 08:23:58 +01:00
Doug Anderson 2adb3b8e6f mfd: rk808: Add register caching
Let's define the voltatile registers (those that can't be cached) and
enable caching.  The rk808 is accessed almost constantly with cpufreq
so this is really nice.

As measured by ftrace:
  before this change: cpu0_set_target() => ~2200us
  after this change:  cpu0_set_target() =>  ~500us

Signed-off-by: Doug Anderson <dianders@chromium.org>
Reviewed-by: Chris Zhong <zyw@rock-chips.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
2014-09-26 08:23:56 +01:00
Charles Keepax cfeb35da2a mfd: arizona: Use handle_simple_irq for IRQ dispatch chip
We use a dummy IRQ chip to dispatch interrupts to the two seperate IRQ
domains on the Arizona devices. This is just a simple software IRQ chip
and thus the current handle_edge_irq is unnecessary for its needs.

Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
2014-09-26 08:23:55 +01:00
Krzysztof Kozlowski be69e9e007 mfd: max14577: Don't pass IRQ domain to mfd_add_devices
The max14577 MFD cells do not have any resources so the IRQ domain
passed to mfd_add_devices is not used.

Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
2014-09-26 08:23:54 +01:00
Sean Cross 851ec59614 mfd: stmpe: Support gpio over irq under device tree
The stmpe_platform_data has a irq_over_gpio field, which allows the
system to read STMPE events whenever an IRQ occurs on a GPIO pin.
This patch adds the ability to configure this field and to use a GPIO
as an IRQ source for boards configuring the STMPE in device tree.

Signed-off-by: Sean Cross <xobs@kosagi.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
2014-09-26 08:23:53 +01:00
Jaewon Kim bdaf67030c mfd: intel_soc_pmic: Add CONFIG_PM_SLEEP check for suspend_fn/resume_fn
This patch fix warning message with CONFIG_PM_SLEEP disabled
If CONFIG_PM_SLEEP is not enabled we receive the following warning message:

drivers/mfd/intel_soc_pmic_core.c:118:12:
 warning: 'intel_soc_pmic_suspend' defined but not used

Signed-off-by: Jaewon Kim <jaewon02.kim@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
2014-09-26 08:23:52 +01:00
Chris Ball 5152970538 mfd: rtsx_pcr: Fix MSI enable error handling
pci_enable_msi() can return failure with both positive and negative
integers -- it returns 0 for success -- but is only tested here for
"if (ret < 0)".  This causes us to try to use MSI on the RTS5249 SD
reader in the Dell XPS 11 when enabling MSI failed, causing:

[    1.737110] rtsx_pci: probe of 0000:05:00.0 failed with error -110

Cc: stable <stable@vger.kernel.org>
Reported-by: D. Jared Dominguez <Jared_Dominguez@Dell.com>
Tested-by: D. Jared Dominguez <Jared_Dominguez@Dell.com>
Signed-off-by: Chris Ball <chris@printf.net>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
2014-09-26 08:23:52 +01:00
Sebastian Andrzej Siewior 6a71f38dd8 mfd: ti_am335x_tscadc: Fix TSC resume
In the resume path, the ADC invokes am335x_tsc_se_set_cache() with 0 as
the steps argument if continous mode is not in use. This in turn disables
all steps and so the TSC is not working until one ADC sampling is
performed.

This patch fixes it by writing the current cached mask instead of the
passed steps.

Fixes: 7ca6740cd1 ("mfd: input: iio: ti_amm335x: Rework TSC/ADCA
synchronization")
Cc: stable@vger.kernel.org # v3.13+
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
2014-09-26 08:23:51 +01:00
Mark Brown 0b496b4c95 mfd: tps65217: Tell regmap what registers are valid
Allow regmap to provide debugfs access to the register map by telling it
what registers are valid.

Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
2014-09-26 08:23:50 +01:00
Markus Pargmann 34a4958e4c mfd: mc13xxx: Configure WDI reset
Setup the PMIC to make a restart when a watchdog interrupt occures.
If this is not configured, the PMIC will shut down the power supply
without a restart.

Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
2014-09-26 08:23:50 +01:00
Andy Shevchenko 970d9fbca9 mfd: pcf50633: Use sprintf directly
When dump a content of the registers let's use snprintf() directly with %*ph
specifier.

Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
2014-09-26 08:23:49 +01:00
Guodong Xu 8bdf87b400 mfd: Add HI6421 PMIC Core driver
This adds driver to support HiSilicon Hi6421 PMIC. Hi6421 includes multi-
functions, such as regulators, codec, ADCs, Coulomb counter, etc.
This driver includes core APIs _only_.

Drivers for individul components, like voltage regulators, are
implemented in corresponding driver directories and files.

Registers in Hi6421 are memory mapped, so using regmap-mmio API.

Signed-off-by: Guodong Xu <guodong.xu@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
2014-09-26 08:23:43 +01:00
Andy Shevchenko 85de80e8df mfd: lpc_sch: Remove FSF address
This patch removes FSF address because it can be changed. While here, update
the copyright lines by adding Intel Corp. to them.

There is no functional change.

Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
2014-09-26 08:15:59 +01:00
Andy Shevchenko ec689a8a81 mfd: lpc_sch: Add support for Intel Quark X1000
Intel Quark X1000 SoC supports IRQ based GPIO. This patch will
enable MFD support for Quark X1000 and provide IRQ resources
to Quark X1000 GPIO device driver.

Signed-off-by: Chang Rebecca Swee Fun <rebecca.swee.fun.chang@intel.com>
Tested-by: Chang Rebecca Swee Fun <rebecca.swee.fun.chang@intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
2014-09-26 08:15:58 +01:00
Andy Shevchenko b24512c860 mfd: lpc_sch: Reduce duplicate code and improve manageability
This patch refactors the driver to use helper functions instead of
copy'n'pasted pieces of code.

It also introduces an additional struct to hold a chipset info. The chipset
info will be used to store features that are supported by specific processor or
chipset. LPC_SCH supports SMBUS, GPIO and WDT features. As this code base might
expand further to support more processors, this implementation will help to
keep code base clean and manageable.

The patch is partially based on the work done by Chang Rebecca Swee Fun.

Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Chang Rebecca Swee Fun <rebecca.swee.fun.chang@intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
2014-09-26 08:15:57 +01:00
Chris Zhong f69a7cf74d mfd: RK808: Add new mfd driver for RK808
The RK808 chip is a power management IC for multimedia and handheld
devices. It contains the following components:

- Regulators
- RTC
- Clkout

The RK808 core driver is registered as a platform driver and provides
communication through I2C with the host device for the different
components.

Signed-off-by: Chris Zhong <zyw@rock-chips.com>
Signed-off-by: Zhang Qing <zhangqing@rock-chips.com>
Tested-by: Heiko <heiko@sntech.de>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
2014-09-26 08:15:56 +01:00
Axel Lin e9e9d39735 mfd: da9052: Avoid setting read_flag_mask for da9052-i2c driver
Current code init regmap with &da9052_regmap_config for both da9052-spi and
da9052-i2c drivers. da9052-spi sets the read_flag_mask.
The same setting may be applied for da9052-i2c if da9052-spi driver is loaded
first because they actually use the same regmap_config setting.
Fix this issue by using a local variable for regmap_config in da9052-spi driver,
so the settings in spi driver won't impact the settings in i2c driver.
Also makes da9052_regmap_config const to avoid similar issue.

Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
2014-09-26 08:15:54 +01:00
Charles Keepax c38715fed8 mfd: arizona: Propagate irq_wake through to parent IRQ
If one of the internal Arizona IRQs is set as a wake source this needs
to be propogated back to the actual IRQ line that the Arizona device is
attached to.

Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
2014-09-26 08:15:54 +01:00
Inha Song cc47aed9a1 mfd: arizona: Add support for INn_Mode register control
Some boards need to set the INn_MODE[1:0] register to change
the input signal patch. This wlf,inmode property is optional.
If present, values must be specified less than or equal to
the number of input singals. If values less than the number
of input signals, elements that has not been specifed are set
to 0 by default.

Example:
   - wlf,inmode = <2 0 2>;	/* IN1, IN3 use DMIC */

Signed-off-by: Inha Song <ideal.song@samsung.com>
Reviewed-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
2014-09-26 08:15:52 +01:00
Charles Keepax c24084db22 mfd: arizona: Add ASYNC_SAMPLE_RATE_2 registers
Some arizona devices have a second asynchronous sample rate, add the
registers necessary to support this.

Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Acked-by: Mark Brown <broonie@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
2014-09-26 08:15:52 +01:00
Beniamino Galvani 9bb9e29c78 mfd: Add Ricoh RN5T618 PMIC core driver
Ricoh RN5T618 is a power management IC which integrates 3 step-down
DCDC converters, 7 low-dropout regulators, a Li-ion battery charger,
fuel gauge, ADC, GPIOs and a watchdog timer.

This commit adds a MFD core driver to support the I2C communication
with the device.

Signed-off-by: Beniamino Galvani <b.galvani@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
2014-09-26 08:15:51 +01:00
Vignesh R 6ac734d224 mfd: ti_am335x_tscadc: Fix TSC operation after ADC continouous mode
After enabling and disabling ADC continuous mode via sysfs, ts_print_raw
fails to return any data. This is because when ADC is configured for
continuous mode, it disables touch screen steps.These steps are not
re-enabled when ADC continuous mode is disabled. Therefore existing values
of REG_SE needs to be cached before enabling continuous mode and
disabling touch screen steps and enabling ADC steps. The cached value
are to be restored to REG_SE once ADC is disabled.

Fixes: 7ca6740cd1 ("mfd: input: iio: ti_amm335x: Rework TSC/ADC synchronization")

Cc: stable@vger.kernel.org # v3.13+
Signed-off-by: Vignesh R <vigneshr@ti.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
2014-09-26 08:15:50 +01:00
Arnout Vandecappelle (Essensium/Mind) be1c770028 mfd: tps65910: Work around silicon erratum SWCZ010
http://www.ti.com/lit/pdf/SWCZ010:
  Glitch on SDA-SCL not managed correctly by the I2C IP

Impact:
The standard specifies that the I2C transfer should restart on a start
event in all cases. The current design does not support two consecutive
Start conditions. This can cause the first real access after such a
glitch to be corrupted.

Description:
An unexpected glitch on SDA and SCL can generate a wrong start event.
In the current design, the SCL line must toggle two times to detect a
new start event and completely restart the I2C access; hence the real
start event is not detected in the case of a single SCL toggle.

Workaround:
Repeat I2C access.

A simpler workaround is to make a dummy transfer just before the first
access to the tps65910 chip. This can be done unconditionally.

Signed-off-by: Arnout Vandecappelle (Essensium/Mind) <arnout@mind.be>
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
2014-09-26 08:15:48 +01:00
Lee Jones 7929fa7740 mfd: stmpe: Rid variable length array Sparse warnings
Numbers are generated by taking the largest currently used values.

drivers/mfd/stmpe.c:252:17:
  warning: Variable length array is used.
drivers/mfd/stmpe.c:857:16:
  warning: Variable length array is used.

Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
2014-09-26 08:15:47 +01:00
Lee Jones 87bd1c9250 mfd: max8925-i2c: Fix variable length array Sparse warning
The largest byte size in use currently is 8.  Fix array size to 9.

drivers/mfd/max8925-i2c.c:40:33:
  warning: Variable length array is used

Signed-off-by: Lee Jones <lee.jones@linaro.org>
2014-09-26 08:15:46 +01:00
Lee Jones 7a36ceb284 mfd: 88pm860x-i2c: Fix variable length array Sparse warning
drivers/mfd/88pm860x-i2c.c:125:33:
  warning: Variable length array is used.

Signed-off-by: Lee Jones <lee.jones@linaro.org>
2014-09-26 08:15:45 +01:00
Lee Jones 260a127bfb mfd: 88pm860x-i2c: Purge unused functions
The following functions appear to be unused since v2.6.39:

  pm860x_page_reg_read()
  pm860x_page_bulk_write()
  pm860x_page_set_bits()

Let's remove them.

Signed-off-by: Lee Jones <lee.jones@linaro.org>
2014-09-26 08:15:45 +01:00
James Ralston fea31042ff mfd: lpc_ich: Add Device IDs for Intel 9 Series PCH
This patch adds the LPC Device IDs for the Intel 9 Series PCH.

Signed-off-by: James Ralston <james.d.ralston@intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
2014-09-26 08:15:44 +01:00
Jacek Anaszewski a0bc607208 mfd: max77693: Improve support for the flash cell
This patch improves support for the flash cell of
max77693 mfd by adding relevant of_compatible field
and a structure for caching related platform data.
Added are also FLASH registers related macro definitions.

Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
2014-09-26 08:15:43 +01:00
Alan Cox ff0c9da013 mfd: lpc_ich: Add PCI ID for Intel Braswell
This is the same as used in Baytrail so add the new PCI ID to the driver's
list of supported IDs.

Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
2014-09-26 08:15:42 +01:00
Axel Lin 378515fc10 mfd: da9052-i2c: Remove duplicate test for I2C_FUNC_SMBUS_BYTE_DATA functionality
Since commit b42261078a ("regmap: i2c: fallback to SMBus if the adapter
does not support standard I2C"), regmap-i2c will check the
I2C_FUNC_SMBUS_[BYTE|WORD]_DATA functionality based on the regmap_config
setting if the adapter does not support standard I2C.

So remove the I2C_FUNC_SMBUS_BYTE_DATA functionality check in the driver code.

Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
2014-09-26 08:15:41 +01:00
Julia Lawall 42a71ef97b mfd: menelaus: Fix error return code
Convert a zero return value on error to a negative one, as returned
elsewhere in the function.

Additionally, converted 1 << 7 to BIT(7) at the suggestion of Lee Jones.

A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)

// <smpl>
(
if@p1 (\(ret < 0\|ret != 0\))
 { ... return ret; }
|
ret@p1 = 0
)
... when != ret = e1
    when != &ret
*if(...)
{
  ... when != ret = e2
      when forall
 return ret;
}

// </smpl>

Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
2014-09-26 08:15:41 +01:00
Charles Keepax 2a3377ee2d mfd: arizona: Avoid use of legacy IRQ mapping
regmap_add_irq_chip is called from arizona_irq_init with the irq_base
specified as -1 and regmap_add_irq_chip uses if (irq_base) to check if
it should use legacy IRQ mapping. As such the irq mappings are currently
added with irq_domain_add_legacy, rather than irq_domain_add_linear.
This is clearly a typo as there is no reason why this driver can't use
irq_domain_add_linear.

This patch corrects this by passing the irq_base as zero to
regmap_add_irq_chip.

Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
2014-09-26 08:15:40 +01:00
Charles Keepax e569d937af mfd: arizona: Mark additional registers as volatile
Mark some additional registers as volatile. The write sequencer control
registers should not be cached, as we don't ever want their value
synchronised as this might cause a write sequence to be accidentally
initiated.

Additionally, the DAC_COMP registers require special preconditions to
write so there values wouldn't be updated accurately during a register
sync.

Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
2014-09-26 08:15:39 +01:00
Mark Brown 48018943eb mfd: wm5102: Mark register write sequencer control 3 readable
During init the core checks if the wm5102 has finished starting by reading
register 0x19 and looking at the value. This read always fails since this
is not a readable register, mark it as being one. While we're at it provide
a constant for the register name (as supplied by Charles Keepax).

Signed-off-by: Mark Brown <broonie@linaro.org>
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
2014-09-26 08:15:38 +01:00
Hans Wennborg 5e9bbf17b3 mfd: rtsx_usb: Fix decimal printf format specifiers prefixed with 0x
The prefix suggests the number should be printed in hex, so use
the %x specifier to do that.

Found by using regex suggested by Joe Perches.

Signed-off-by: Hans Wennborg <hans@hanshq.net>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
2014-09-26 08:15:38 +01:00
Julia Lawall f2b8678161 mfd: twl6040: Fix error return code
Convert a zero return value on error to a negative one, as returned
elsewhere in the function.

A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)

// <smpl>
(
if@p1 (\(ret < 0\|ret != 0\))
 { ... return ret; }
|
ret@p1 = 0
)
... when != ret = e1
    when != &ret
*if(...)
{
  ... when != ret = e2
      when forall
 return ret;
}

// </smpl>

Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
2014-09-26 08:15:37 +01:00
Mark Brown 6052d83e71 mfd: wm8994: Allow modular build
The interfaces that used to be built in only (interrupts IIRC) no longer
are so allow the driver to be built as a module fixing arm64 allmodconfig
builds.

Signed-off-by: Mark Brown <broonie@linaro.org>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
2014-09-26 08:15:36 +01:00
Himangi Saraogi e0c8a1f52d mfd: menelaus: Remove null pointer dereference
If vtg is NULL, it is not possible to access its mode_reg field. At all
sites where the static function menelaus_set_voltage is called, the first
argument is the address of a structure defined in the file. So, the null
test is unnecessary and is removed. Also, a label is done away with.

This problem was found using the following Coccinelle semantic match:

// <smpl>
@@
expression E, E1;
identifier f;
statement S1,S2,S3;
@@

* if (E == NULL)
{
  ... when != if (E == NULL) S1 else S2
      when != E = E1
* E->f
  ... when any
  return ...;
}
else S3
// </smpl>

Signed-off-by: Himangi Saraogi <himangi774@gmail.com>
Acked-by: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
2014-09-26 08:15:36 +01:00
Lee Jones 7821d9b24b mfd: wm8994: Export symbols ready for built-in => modular build
We'd like to be able to build the WM8994 family as modules, but the
build will fail if the external symbols aren't exported first.

Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
2014-09-26 08:15:35 +01:00
Lee Jones 5f114ebcee mfd: sm501: Avoid implicit sign extension
Suspicious implicit sign extension where 'reg' (unsigned char) is
promoted in reg << clksrc to int, then sign-extended to unsigned
long. If reg << clksrc is greater than 0x7FFFFFFF, the upper bits
of the result will all be 1.

Signed-off-by: Lee Jones <lee.jones@linaro.org>
2014-09-26 08:15:34 +01:00
Lee Jones 8a012ff9d8 mfd: twl4030-irq: Check return value from twl_i2c_write() - warn() on failure
In the original code a return value variable was provided, but it
was never checked and the user was never informed of failure.  Now
it is and they are.

Signed-off-by: Lee Jones <lee.jones@linaro.org>
2014-09-26 08:15:34 +01:00
Lee Jones cddc11412d mfd: pcf50633: Check return value of platform_device_add()
The return value of platform_device_add() is checked after every
other use throughout the kernel.

We're also sliding in another cheeky dev_err() => dev_warn() change
as we're not actually erroring out here, rather reporting the fact
that something's gone wrong, but carrying on regardless.

Signed-off-by: Lee Jones <lee.jones@linaro.org>
2014-09-26 08:15:33 +01:00
Lee Jones b87d9a0fed mfd: max77686: Remove check which is always true
As 'reg' is unsigned, it can't be less than 0, so checking if it is
greater than or equal to 0 will always result in a true condition.

Signed-off-by: Lee Jones <lee.jones@linaro.org>
2014-09-26 08:15:32 +01:00
Lee Jones 616e047992 mfd: wm5102: Insert missing break in case statement
Chip identifier wm5102_reva_patch is always overwritten with
wm5102_revb_patch, even when the code is run on a Rev-A chip.  Place
in the missing break to force the code into doing something sensible
instead.

Signed-off-by: Lee Jones <lee.jones@linaro.org>
2014-09-26 08:15:31 +01:00
Lee Jones 9b6a5ad9da mfd: htc-i2cpld: Rectify pointer offset error
Checking the result of container_of() against NULL will always result to
false.  Using the offset of member 'chip_out' to find the start of 'struct
htcpld_chip' will result in an offset error when .get_chip() is attempting
to obtain 'htcpld-in'.  Instead, we'll use the correct member based on a
previously the set chip label.

Signed-off-by: Lee Jones <lee.jones@linaro.org>
2014-09-26 08:15:31 +01:00
Lee Jones 41cc08e955 mfd: htc-i2cpld: Use '!variable' instead of 'variable == NULL'
This aids in consistency, as the rest of the checks in the file use this
notation.

Signed-off-by: Lee Jones <lee.jones@linaro.org>
2014-09-26 08:15:30 +01:00
Lee Jones fe4b7ea8e7 mfd: htc-i2cpld: container_of() cannot return NULL
Logically dead code (DEADCODE)

dead_error_line: Execution cannot reach this statement: return;

Remove the check for NULL.

Signed-off-by: Lee Jones <lee.jones@linaro.org>
2014-09-26 08:15:29 +01:00
Lee Jones 0608bab8c7 Merge branches 'ib-mfd-arm-3.18', 'ib-mfd-hwmon-leds-watchdog-3.18' and 'ib-mfd-power-charger-regulator-3.18' into ibs-for-mfd-merged 2014-09-26 08:14:30 +01:00
Sebastian Reichel fd642bb94c Immutable branch between MFD, Power, Charger and Regulator for v3.18
-----BEGIN PGP SIGNATURE-----
 Version: GnuPG v1
 
 iQIcBAABAgAGBQJUItS7AAoJEFGvii+H/Hdh4ZUP/A+ZEczItBIKr/+iwT/4bwp0
 j1UwBlT8Qn7YNjX8bpRb0q1wL/vmw6DYSMMBxVmmLQ1eEyOpLAgJJ5YcsFRaX2xk
 z5XBHQvERPWZjtRexj6pFeKSNeAW5nLVuppMIvl827nTL2mC6UDD8XuH+6FpYqt+
 U/yVCjZzL/q3QKdFQja5qIHTBOndHju3HcKLzPAvq8XOXv/O9V0T4M6lssaLwo0N
 5jGiZkjRKD8nXBVqXHEpGgljFPW0YP+zhL9yKKqNWgBqgMQkUuSrFNPkWNbpdsDY
 vYkY1CLARO5DYWHBIqaQ//RSR6Z7yMVhHTaJPMkBRYFYHLxgyBxXy0WfzdNMUagG
 uVZJahu8pJiFN02HhoV9taE/h6Xl5PrZTTZDsP3RVAmbVd762dP/e3uaF5l6rqiv
 tTGB1qlnt+rQeIabsJl7FsWDD28ZmziAy6HoOWlxF4QY4R+U+iAbCHxuOWipFA+B
 RTqQQIrg+fsXWHVjzdJRGzwxo6XcB5uAzAAowTEINk+5iUGZfXEVXd9oEnnSj8iw
 a9mNASaBkwcwMPQjLYAMIhoNewXFDFCAattyWd5Nn9KfiYdaU+cbX9Ojc16zVdfB
 Fbd8DgvV0GcqCPu1SQ94GXEcGNgEB1p94o/KhfVJ385umRF3q32y5+MlwzCpKUu4
 I5OHz6vwkfPXEjc207xB
 =T7dV
 -----END PGP SIGNATURE-----

Merge tag 'tags/mfd-power-charger-regulator-v3.18' into next

Immutable branch between MFD, Power, Charger and Regulator for v3.18
2014-09-25 01:55:14 +02:00
Guenter Roeck 7ad8966f4f Immutable branch between MFD, HWMON, LEDs and Watchdog for v3.18
-----BEGIN PGP SIGNATURE-----
 Version: GnuPG v1
 
 iQIcBAABAgAGBQJUItc7AAoJEFGvii+H/HdhxTEP/A0Gg35acsBa8JPWUGuTcGTi
 GHDdnDh1sJtJWadKhs+JV9tOX80YY/5OaHr0TKXcb0eAZopqG4G4yyJXmju+rkFn
 sp4nQ4QzM8gNzmVpo6K45xdZw913QQbVcwDThnZwq1xMHVvMT2TFZ+PQLXZ2e2kN
 HRs65Ftw9geNlZ6cLSXPa+fmhbhC90izXRYB/+eSv9LfxJkARVBtRwVkjLnbe52h
 V7gm/sqcdLs4S0Iauv3qPCjmNCtLWjzJsjq+umiEmmwRvWXGHcLWxCSbmrMsi075
 VmMTY1G+ys2OaNo4wpMEx3s2+Cg/dxyMKfuJn3Zz+Wk196v4UaQWFKBfH8IcjcuJ
 zKy9RntFZ6Esut/PeaMlk7nlgkSXOEbQZFcMDhn8LFwL8LzVDUIMtmcIEsfwHfme
 SWGt6lYUkeSC0yxdylYtIvAKVhkSInkg0z7YiChB0eHflBgWsNn4r8v5iGk9yAXu
 keR9sQlXKS2gFbMtZ8e+VgNVqPmapJx+1E1F5/JbjVpiQG+fzsleHi9UF91pyLJL
 IGZM51l2FEMBMuKSNEUy+mcLX4Y/63iEg3fGvv5nX52A0MVrL47ADDJSEoaZoUpg
 Yz3AW/+yYKi5cmcZ7sUirrCHawvfIYGeR1jZjYaIk8lAeqjFHTDzayIXUoOoQfN7
 vi+fRCxYLA/Z/Rnfylmt
 =keMM
 -----END PGP SIGNATURE-----

Merge tag 'mfd-hwmon-leds-watchdog-v3.18' into hwmon-next

Immutable branch between MFD, HWMON, LEDs and Watchdog for v3.18
2014-09-24 09:25:06 -07:00
Krzysztof Kozlowski b8f139f68f regulator/mfd: max14577: Export symbols for calculating charger current
This patch prepares for changing the max14577 charger driver to allow
configuring battery-dependent settings from DTS.

The patch moves from regulator driver to MFD core driver and exports:
 - function for calculating register value for charger's current;
 - table of limits for chargers (MAX14577, MAX77836).

Previously they were used only by the max14577 regulator driver. In next
patch the charger driver will use them as well. Exporting them will
reduce unnecessary code duplication.

Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Acked-by: Mark Brown <broonie@linaro.org>
Acked-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
2014-09-24 15:25:47 +01:00
Krzysztof Kozlowski 4476767cff mfd: max14577: Map charger device to its own of_node
Add a "maxim,max14577-charger" of_compatible to the mfd_cell so the
MFD child device (the charger) will have its own of_node set. This will
be used by the max14577 charger driver in next patches to obtain battery
configuration from DTS.

Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Acked-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
2014-09-24 13:42:46 +01:00
Andreas Werner dfbdcd7cef mfd: menf21bmc: Introduce MEN 14F021P00 BMC MFD Core driver
The MEN 14F021P00 Board Management Controller provides an
I2C interface to the host to access the feature implemented in the BMC.
The BMC is a PIC Microntroller assembled on CPCI Card from MEN Mikroelektronik
and on a few Box/Display Computer.

Added MFD Core driver, supporting the I2C communication to the device.

The MFD driver currently supports the following features:
 	- Watchdog
 	- LEDs
	- Hwmon (voltage monitoring)

Signed-off-by: Andreas Werner <andreas.werner@men.de>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
2014-09-24 13:30:16 +01:00
abdoulaye berthe 88d5e520aa driver:gpio remove all usage of gpio_remove retval in driver
this remove all reference to gpio_remove retval in all driver
except pinctrl and gpio. the same thing is done for gpio and
pinctrl in two different patches.

Signed-off-by: Abdoulaye Berthe <berthe.ab@gmail.com>
Acked-by: Michael Büsch <m@bues.ch>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Acked-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Acked-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2014-09-18 11:03:10 -07:00
Shawn Guo ee64100953 Immutable branch between MFD and some ARM sub-arch maintainers.
-----BEGIN PGP SIGNATURE-----
 Version: GnuPG v1
 
 iQIcBAABAgAGBQJUAENKAAoJEFGvii+H/HdhBFAQAK3GH6D8Ie7GmIx4IgqgrXOn
 bZi2ZsSRJPMQE5qIIOlVfacOEg329//M2ZPUtYoJsyFFM5aJf+OxIk1TbK+S5c9F
 ybP0TT23RD88UCSzDBpryIfaUHoUaZy+dchzezFsUHNYYg/wt94yRBHGfx5Fmqsk
 doXxlitc5OPbsQ6oRN5znnyxmkwP62NuTlz+hJNSaxi39paUQRLUe44xP9BezbMR
 B0d2wHghkfEkLV1VMwgHek2bqTAb7/aInNnM5JGqjvmvq6M81nHE7FE+trlhmwWT
 1swG3MI8cWr5e8MtuFO3d74+BPbhAjmmJDT4FVffOm7C7Qbs7m/GYEB2FJ4QrZF3
 mIx2ipBCqpQra7+ctk+yX+fH2Ne2Ykd4XJ388JffIdYY4fxi3443GIueKyUhjj2j
 kb0/M5F/K+vA+U4BureR5LtcrBxWFcesxKVr91HdMUB8s1fd1QjL8sPgM7RseNfS
 UHISaXejyaRg0IVnBMlt9albiA5JlvxH3WiuKS3Z69wT/FPkK4MLGJlM2cDlIdAY
 PiyL8dsi/ANCv9rfrc5hWkT/Dzx9vmp7yr+lXuEvgJcDgErYe5awT+OHjP+uXX3K
 RJ2oLDV3pRmbnl3T9KzBn1e0cq9cDkmZjItyk5+oPIrVR37HuHGo0uDL/uDqUoqR
 fO+L5ibUCACkdu+cxl5S
 =T5Jh
 -----END PGP SIGNATURE-----

Merge tag 'ib-mfd-arm-v3.18' into imx/dt

Immutable branch between MFD and some ARM sub-arch maintainers.
2014-09-16 10:24:16 +08:00
Steve Twiss bd597f47ca devicetree: Dialog Semiconductor consolidate existing vendor prefixes to standardise on 'dlg'
This patch series updates the device tree vendor prefix for
Dialog Semiconductor.

Various methods are currently used throughout the kernel: 'diasemi',
'dialog' and 'dlg'. Others have also been suggested.

This patch set aims to consolidate the usage of the vendor prefix to
use a common standard. The prefix 'dlg' is used.

Signed-off-by: Steve Twiss <stwiss.opensource@diasemi.com>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Shawn Guo <shawn.guo@freescale.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
2014-08-29 09:26:29 +01:00
Tony Lindgren daebabd578 mfd: twl4030-power: Fix PM idle pin configuration to not conflict with regulators
Commit 43fef47f94 (mfd: twl4030-power: Add a configuration to turn
off oscillator during off-idle) added support for configuring the PMIC
to cut off resources during deeper idle states to save power.

This however caused regression for n900 display power that needed the
PMIC configuration to be disabled with commit d937678ab6 (ARM: dts:
Revert enabling of twl configuration for n900).

Turns out the root cause of the problem is that we must use
TWL4030_RESCONFIG_UNDEF instead of DEV_GRP_NULL to avoid disabling
regulators that may have been enabled before the init function
for twl4030-power.c runs. With TWL4030_RESCONFIG_UNDEF we let the
regulator framework control the regulators like it should. Here we
need to only configure the sys_clken and sys_off_mode triggers for
the regulators that cannot be done by the regulator framework as
it's not running at that point.

This allows us to enable the PMIC configuration for n900.

Fixes: 43fef47f94 (mfd: twl4030-power: Add a configuration to turn off oscillator during off-idle)

Cc: stable@vger.kernel.org # v3.16
Signed-off-by: Tony Lindgren <tony@atomide.com>
Tested-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
2014-08-28 15:57:55 +01:00
Fabio Estevam 72ef8e4b3b mfd: ab8500-core: Use 'ifdef' for config options
The config symbol 'CONFIG_DEBUG_FS' should be protected by a 'ifdef' instead
of a plain 'if'.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
2014-08-20 13:28:02 +01:00
Hans Wennborg 6065c9a472 mfd: htc-i2cpld: Fix %d confusingly prefixed with 0x in format string
Signed-off-by: Hans Wennborg <hans@hanshq.net>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
2014-08-20 13:27:48 +01:00
Hans Wennborg ddde06b181 mfd: omap-usb-host: Fix %d confusingly prefixed with 0x in format string
Signed-off-by: Hans Wennborg <hans@hanshq.net>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
2014-08-20 13:26:52 +01:00
Jeff Mahoney 1813908986 drivers/mfd/rtsx_usb.c: export device table
The rtsx_usb driver contains the table for the devices it supports but
doesn't export it.  As a result, no alias is generated and it doesn't
get loaded automatically.

Via https://bugzilla.novell.com/show_bug.cgi?id=890096

Signed-off-by: Jeff Mahoney <jeffm@suse.com>
Reported-by: Marcel Witte <wittemar@googlemail.com>
Cc: Roger Tseng <rogerable@realtek.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2014-08-14 10:56:15 -06:00
Linus Torvalds 54c72d5987 == Changes to existing drivers ==
- Checkpatch fixes throughout the subsystem
   - Use Regmap to handle IRQs in max77686, extcon-max77693 and mc13xxx-core
   - Use DMA in rtsx_pcr
   - Restrict building on unsupported architectures on timberdale, cs5535
   - SPI hardening in cros_ec_spi
   - More robust error handing in asic3, cros_ec, ab8500-debugfs,
         max77686 and pcf50633-core
   - Reorder PM runtime and regulator handing during shutdown in arizona
   - Enable wakeup in cros_ec_spi
   - Unused variable/code clean-up in pm8921-core, cros_ec, htc-i2cpld,
         tps65912-spi, wm5110-tables and ab8500-debugfs
   - Add regulator handing into suspend() in sec-core
   - Remove pointless wrapper functions in extcon-max77693 and i2c-cros-ec-tunnel
   - Use cross-architecture friendly data sizes in stmpe-i2c, arizona,
         max77686 and tps65910
   - Device Tree documentation updates throughout
   - Provide power management support in max77686
   - Few OF clean-ups in max77686
   - Use manged resources in tps6105x
 
  == New drivers/supported devices ==
   - Add support for s2mpu02 to sec-core
   - Add support for Allwinner A32 to sun6i-prcm
   - Add support for Maxim 77802 in max77686
   - Add support for DA9063 AD in da9063
   - Add new driver for Intel PMICs (generic) and specifically Crystal Cove
 
  == (Re-)moved drivers ==
   - Move out keyboard functionality cros_ec ==> input/keyboard/cros_ec_keyb
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v1
 
 iQIcBAABAgAGBQJT40p7AAoJEFGvii+H/HdhTo0P/1GuZyvCAJCeqt2oN1gcloIe
 Hgf5rEo/PVPh3T9vHA7GCbWhgtdxfJI8FxrQYvU7Dw5cEMlmvl5p/ZHNPIProv97
 uI59JO67roLpXZP+aYX8BzXcplYkaR/ah16o/ePtaOCwGrXDz+TtJiHEVVN/8bAG
 PWsdcDNBC8byP7BZ/8zFdu6pX4800eRZ0KgeBH+u4k6UDor7M6LkQrxF1hJhU1Bv
 z14Q2wKQufhbcyEtQWcYc6M8hignD1Ioyd4I8mnEJs0EUiABfGUEk/K/G4Z5Q7Sv
 eRIEPZCd1CEBKD5JQcPXyE1QGdG9GiD15PLmctPA4VY1V+9c5/Hoq0TLoxlAQNWA
 gUr7WSqJ+KT2Nch0WVr/MdP8l0jPYfboWbsd/apj4GK0/9quwJNkGUxx0mCdCXyg
 9ylitwUrmlrd4CEKjybfEuTQB52Jvcdq24fnNYHHn1TGppZH6w7LVvdwSW7UcjF0
 Y48hTImYYnVAlWl5lE5xVQTWD/3hseAcoWTsdSORSWJbkCfAhJUg/Gn5bH/Fkwhs
 /aWYPvkF+m47PoudZ9Z8qB5OTO4uz/Q9uEBBf2/k4Yy95vl2IZdy9VqS5tYG67e7
 LLdAZvG5hjEwDi3OwcwGSdZ/kRB5Hgq/YvpqjItle86CKj0ECdAqL/PfqLISgJq9
 x3zSuWMRLcNoyhc2HnBj
 =2cNI
 -----END PGP SIGNATURE-----

Merge tag 'mfd-for-linus-3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd

Pull MFD update from Lee Jones:
 "Changes to existing drivers:
   - checkpatch fixes throughout the subsystem
   - use Regmap to handle IRQs in max77686, extcon-max77693 and
     mc13xxx-core
   - use DMA in rtsx_pcr
   - restrict building on unsupported architectures on timberdale,
     cs5535
   - SPI hardening in cros_ec_spi
   - more robust error handing in asic3, cros_ec, ab8500-debugfs,
     max77686 and pcf50633-core
   - reorder PM runtime and regulator handing during shutdown in arizona
   - enable wakeup in cros_ec_spi
   - unused variable/code clean-up in pm8921-core, cros_ec, htc-i2cpld,
     tps65912-spi, wm5110-tables and ab8500-debugfs
   - add regulator handing into suspend() in sec-core
   - remove pointless wrapper functions in extcon-max77693 and
     i2c-cros-ec-tunnel
   - use cross-architecture friendly data sizes in stmpe-i2c, arizona,
     max77686 and tps65910
   - devicetree documentation updates throughout
   - provide power management support in max77686
   - few OF clean-ups in max77686
   - use manged resources in tps6105x

  New drivers/supported devices:
   - add support for s2mpu02 to sec-core
   - add support for Allwinner A32 to sun6i-prcm
   - add support for Maxim 77802 in max77686
   - add support for DA9063 AD in da9063
   - new driver for Intel PMICs (generic) and specifically Crystal Cove

  (Re-)moved drivers ==
   - move out keyboard functionality cros_ec ==> input/keyboard/cros_ec_keyb"

* tag 'mfd-for-linus-3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd: (101 commits)
  MAINTAINERS: Update MFD repo location
  mfd: omap-usb-host: Fix improper mask use.
  mfd: arizona: Only free the CTRLIF_ERR IRQ if we requested it
  mfd: arizona: Add missing handling for ISRC3 under/overclocked
  mfd: wm5110: Add new interrupt register definitions
  mfd: arizona: Rename thermal shutdown interrupt
  mfd: wm5110: Add in the output done interrupts
  mfd: wm5110: Remove non-existant interrupts
  mfd: tps65912-spi: Remove unused variable
  mfd: htc-i2cpld: Remove unused code
  mfd: da9063: Add support for AD silicon variant
  mfd: arizona: Map MICVDD from extcon device to the Arizona core
  mfd: arizona: Add MICVDD to mapped regulators for wm8997
  mfd: max77686: Ensure device type IDs are architecture agnostic
  mfd: max77686: Add Maxim 77802 PMIC support
  mfd: tps6105x: Use managed resources when allocating memory
  mfd: wm8997-tables: Suppress 'line over 80 chars' warnings
  mfd: kempld-core: Correct a variety of checkpatch warnings
  mfd: ipaq-micro: Fix coding style errors/warnings reported by checkpatch
  mfd: si476x-cmd: Remedy checkpatch style complains
  ...
2014-08-07 17:17:39 -07:00
Linus Torvalds 158c12948f Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial
Pull trivial tree changes from Jiri Kosina:
 "Summer edition of trivial tree updates"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (23 commits)
  doc: fix two typos in watchdog-api.txt
  irq-gic: remove file name from heading comment
  MAINTAINERS: Add miscdevice.h to file list for char/misc drivers.
  scsi: mvsas: mv_sas.c: Fix for possible null pointer dereference
  doc: replace "practise" with "practice" in Documentation
  befs: remove check for CONFIG_BEFS_RW
  scsi: doc: fix 'SCSI_NCR_SETUP_MASTER_PARITY'
  drivers/usb/phy/phy.c: remove a leading space
  mfd: fix comment
  cpuidle: fix comment
  doc: hpfall.c: fix missing null-terminate after strncpy call
  usb: doc: hotplug.txt code typos
  kbuild: fix comment in Makefile.modinst
  SH: add proper prompt to SH_MAGIC_PANEL_R2_VERSION
  ARM: msm: Remove MSM_SCM
  crypto: Remove MPILIB_EXTRA
  doc: CN: remove dead link, kerneltrap.org no longer works
  media: update reference, kerneltrap.org no longer works
  hexagon: update reference, kerneltrap.org no longer works
  doc: LSM: update reference, kerneltrap.org no longer works
  ...
2014-08-06 21:03:53 -07:00
Linus Torvalds e7fda6c4c3 Merge branch 'timers-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull timer and time updates from Thomas Gleixner:
 "A rather large update of timers, timekeeping & co

   - Core timekeeping code is year-2038 safe now for 32bit machines.
     Now we just need to fix all in kernel users and the gazillion of
     user space interfaces which rely on timespec/timeval :)

   - Better cache layout for the timekeeping internal data structures.

   - Proper nanosecond based interfaces for in kernel users.

   - Tree wide cleanup of code which wants nanoseconds but does hoops
     and loops to convert back and forth from timespecs.  Some of it
     definitely belongs into the ugly code museum.

   - Consolidation of the timekeeping interface zoo.

   - A fast NMI safe accessor to clock monotonic for tracing.  This is a
     long standing request to support correlated user/kernel space
     traces.  With proper NTP frequency correction it's also suitable
     for correlation of traces accross separate machines.

   - Checkpoint/restart support for timerfd.

   - A few NOHZ[_FULL] improvements in the [hr]timer code.

   - Code move from kernel to kernel/time of all time* related code.

   - New clocksource/event drivers from the ARM universe.  I'm really
     impressed that despite an architected timer in the newer chips SoC
     manufacturers insist on inventing new and differently broken SoC
     specific timers.

[ Ed. "Impressed"? I don't think that word means what you think it means ]

   - Another round of code move from arch to drivers.  Looks like most
     of the legacy mess in ARM regarding timers is sorted out except for
     a few obnoxious strongholds.

   - The usual updates and fixlets all over the place"

* 'timers-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (114 commits)
  timekeeping: Fixup typo in update_vsyscall_old definition
  clocksource: document some basic timekeeping concepts
  timekeeping: Use cached ntp_tick_length when accumulating error
  timekeeping: Rework frequency adjustments to work better w/ nohz
  timekeeping: Minor fixup for timespec64->timespec assignment
  ftrace: Provide trace clocks monotonic
  timekeeping: Provide fast and NMI safe access to CLOCK_MONOTONIC
  seqcount: Add raw_write_seqcount_latch()
  seqcount: Provide raw_read_seqcount()
  timekeeping: Use tk_read_base as argument for timekeeping_get_ns()
  timekeeping: Create struct tk_read_base and use it in struct timekeeper
  timekeeping: Restructure the timekeeper some more
  clocksource: Get rid of cycle_last
  clocksource: Move cycle_last validation to core code
  clocksource: Make delta calculation a function
  wireless: ath9k: Get rid of timespec conversions
  drm: vmwgfx: Use nsec based interfaces
  drm: i915: Use nsec based interfaces
  timekeeping: Provide ktime_get_raw()
  hangcheck-timer: Use ktime_get_ns()
  ...
2014-08-05 17:46:42 -07:00
Mark Brown f71f26274d Merge remote-tracking branches 'regulator/topic/s2mps11', 'regulator/topic/s2mpu02', 'regulator/topic/s5m8767' and 'regulator/topic/tps65090' into regulator-next 2014-08-05 18:29:27 +01:00
Mark Brown d5b5d9d43b Merge remote-tracking branches 'regulator/topic/lp8755', 'regulator/topic/ltc3589', 'regulator/topic/max8952', 'regulator/topic/mc13xxx' and 'regulator/topic/palmas' into regulator-next 2014-08-05 18:29:24 +01:00
Michael Welling 46de8ff8e8 mfd: omap-usb-host: Fix improper mask use.
single-ulpi-bypass is a flag used for older OMAP3 silicon.

The flag when set, can excite code that improperly uses the
OMAP_UHH_HOSTCONFIG_UPLI_BYPASS define to clear the corresponding bit.
Instead it clears all of the other bits disabling all of the ports in
the process.

Cc: stable@vger.kernel.org
Signed-off-by: Michael Welling <mwelling@emacinc.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
2014-07-29 16:08:49 +01:00
Charles Keepax 30a2af3a32 mfd: arizona: Only free the CTRLIF_ERR IRQ if we requested it
We only request the control interface error IRQ if we set ctrlif_error,
as such we should only free it in that situation. Otherwise we will
attempt to free an IRQ we never requested and get a warning from the IRQ
core.

This patch moves the ctrlif_error variable into the arizona structure
and checks it in all cases we free the control interface error IRQ.

Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
2014-07-28 11:01:47 +01:00
Charles Keepax 6e440d27aa mfd: arizona: Add missing handling for ISRC3 under/overclocked
Some parts have a third ISRC, this patch adds handling for the under and
overclocked interrupts from this ISRC.

Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
2014-07-28 11:01:45 +01:00
Charles Keepax 3215501fc9 mfd: wm5110: Add new interrupt register definitions
Newer versions of the IP have a lot of new interrupts and move several
existing interrupts. This patch adds the register definitions and regmap
hookup for these interrupts.

Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
2014-07-28 11:01:42 +01:00
Charles Keepax c0fe2c5b3f mfd: arizona: Rename thermal shutdown interrupt
Newer versions of the IP introduce short circuit protection which will
also shutdown the speaker. Rename the interrupt and associated register
bits associated with thermal events to better fit the function and avoid
conflict with future interrupt additions.

Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
2014-07-28 08:10:47 +01:00
Charles Keepax 3d2108dae4 mfd: wm5110: Add in the output done interrupts
wm5110 has interrupts to signal that an output has fully enabled. This
patch adds in these interrupts although use is not made of them yet.

Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
2014-07-28 08:10:33 +01:00
Charles Keepax 77556bb131 mfd: wm5110: Remove non-existant interrupts
The DCS_DAC_DONE and DCS_HP_DONE interrupts do not exist on the wm5110
version of the IP. This patch removes them from the regmap IRQ
structure.

Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
2014-07-28 08:10:19 +01:00
Sachin Kamat 36ab08eeeb mfd: tps65912-spi: Remove unused variable
‘rx_buf’ is not used in this function.

Signed-off-by: Sachin Kamat <sachin.kamat@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
2014-07-28 08:10:06 +01:00
Sachin Kamat 0a73b28f74 mfd: htc-i2cpld: Remove unused code
Removed code unused in this function.

Signed-off-by: Sachin Kamat <sachin.kamat@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
2014-07-28 08:09:45 +01:00
Opensource [Steve Twiss] 9cb42e2a8e mfd: da9063: Add support for AD silicon variant
Add register definitions for DA9063 AD (0x3) silicon variant ID
the ability to choose the silicon variant at run-time using regmap
configuration. This patch also adds RTC support for the AD silicon
changes.

It adds both BB and AD support as regmap ranges and then makes the
distinction between the two tables at run-time. This allows both AD
and BB silicon variants to be supported at the same time.

Suggested-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Opensource [Steve Twiss] <stwiss.opensource@diasemi.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
2014-07-28 08:09:25 +01:00
Charles Keepax 5fc6c39653 mfd: arizona: Map MICVDD from extcon device to the Arizona core
The extcon driver should be able to get its regulator against rather
than against the main arizona device, we must add a supply mapping
allowing the regulator to be located. This patch does so.

Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
2014-07-28 08:09:10 +01:00
Charles Keepax 996c2d4f58 mfd: arizona: Add MICVDD to mapped regulators for wm8997
The previous update adding MICVDD to the regulator mappings:

mfd: arizona: Add MICVDD to mapped regulators

Only added the mapping for wm5102 and wm5110 but wm8997 also has a
MICVDD supply that needs to be mapped back to the main Arizona device.

Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
2014-07-28 08:08:53 +01:00