Commit Graph

90 Commits

Author SHA1 Message Date
Arseny Solokha 38a99bd773 i2c: mpc: always determine I2C clock prescaler at runtime
Remove the facility for setting the prescaler value at compile time
entirely. It was only used for two SoCs, duplicating the actual value
for one of them and setting sometimes bogus value for another. Make all
MPC8xxx SoCs obtain their actual I2C clock prescaler from a single place
in the code.

Changes from v2:
- left Device Tree compatibles in place

Signed-off-by: Arseny Solokha <asolokha@kb.kras.ru>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2018-01-15 19:19:55 +01:00
Arseny Solokha 7575a745f9 i2c: mpc: fix PORDEVSR2 mask for MPC8533/44
According to the reference manuals for the corresponding SoCs, SEC
frequency ratio configuration is indicated by bit 26 of the POR Device
Status Register 2. Consequently, SEC_CFG bit should be tested by mask 0x20,
not 0x80. Testing the wrong bit leads to selection of wrong I2C clock
prescaler on those SoCs.

Signed-off-by: Arseny Solokha <asolokha@kb.kras.ru>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2018-01-15 19:16:14 +01:00
Arseny Solokha f6214f6f2b i2c: mpc: unify obtaining the MPC8533/44 I2C clock prescaler w/ MPC8xxx
Commit 8ce795cb0c ("i2c: mpc: assign the correct prescaler from SVR")
introduced the common helper function for obtaining the actual clock
prescaler value for MPC85xx. However, getting the prescaler for MPC8544
which depends on the SEC frequency ratio on this platform, has been always
performed separately based on the corresponding Device Tree configuration.

Move special handling of MPC8544 into that common helper. Make it dependent
on the SoC version and not on Device Tree compatible node, as is the case
with all other SoCs. Handle MPC8533 the same way which is similar
to MPC8544 in this regard, according to AN2919 "Determining the I2C
Frequency Divider Ratio for SCL".

Signed-off-by: Arseny Solokha <asolokha@kb.kras.ru>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2018-01-15 19:13:33 +01:00
Arseny Solokha 6d10613919 i2c: mpc: get MPC8xxx I2C clock prescaler before using it in calculations
Obtaining the actual I2C clock prescaler value in mpc_i2c_setup_8xxx() only
happens when the clock parameter is set to something other than
MPC_I2C_CLOCK_LEGACY. When the clock parameter is exactly
MPC_I2C_CLOCK_LEGACY, the prescaler parameter is used in arithmetic
division as provided by the caller, resulting in a division by zero
for the majority of processors supported by the module.

Avoid division by zero by obtaining the actual I2C clock prescaler
in mpc_i2c_setup_8xxx() unconditionally regardless of the passed clock
value.

Signed-off-by: Arseny Solokha <asolokha@kb.kras.ru>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2018-01-15 19:13:06 +01:00
Wolfram Sang af3366753f i2c: mpc: remove useless variable initialization
cppcheck rightfully says:

drivers/i2c/busses/i2c-mpc.c:329: style: Variable 'node' is reassigned a value before the old one has been used.

Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2017-11-01 23:51:49 +01:00
Julia Lawall 750bd8b990 i2c: mpc: use of_property_read_bool
Use of_property_read_bool to check for the existence of a property.

Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2017-10-27 22:14:40 +02:00
Ingo Molnar 174cd4b1e5 sched/headers: Prepare to move signal wakeup & sigpending methods from <linux/sched.h> into <linux/sched/signal.h>
Fix up affected files that include this signal functionality via sched.h.

Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
2017-03-02 08:42:32 +01:00
Wolfram Sang ea734404f3 i2c: don't print error when adding adapter fails
The core will do this for us now.

Signed-off-by: Wolfram Sang <wsa-dev@sang-engineering.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Acked-by: Peter Korsgaard <peter@korsgaard.com>
Acked-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Acked-by: Ray Jui <ray.jui@broadcom.com>
Acked-by: Vladimir Zapolskiy <vz@mleia.com>
Acked-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Acked-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Acked-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2016-08-22 08:19:55 +02:00
Amit Tomar 9c836d0c44 i2c: mpc: Fix ISR return value
ISR should not return IRQ_HANDLED for not handling anything.
This patch fixes the return value of ISR for the same case.

Signed-off-by: Amit Singh Tomar <amit.tomar@freescale.com>
Acked-by: Danielle Costantino <danielle.costantino@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2015-03-27 16:53:41 +01:00
Valentin Longchamp 8ce795cb0c i2c: mpc: assign the correct prescaler from SVR
For the 85xx platforms, the source clock for the i2c-mpc can change from
one SoC to another. This is documented in the AN2919 "Determining the
I2C Frequency Divider Ratio for SCL" by Freescale. Not taking this into
account can lead to the output SCL frequency to by off by an offset. It
was observed on the P2041 from the QorIQ family.

This patch fixes this problem by setting the prescaler value to the
appropriate value when required. The SoCs that required a different
prescaler than 1 are identified by reading out the SVR as discussed in
http://thread.gmane.org/gmane.linux.drivers.devicetree/94247/focus=20556

Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2015-03-15 11:04:54 +01:00
Linus Torvalds e6b5be2be4 Driver core patches for 3.19-rc1
Here's the set of driver core patches for 3.19-rc1.
 
 They are dominated by the removal of the .owner field in platform
 drivers.  They touch a lot of files, but they are "simple" changes, just
 removing a line in a structure.
 
 Other than that, a few minor driver core and debugfs changes.  There are
 some ath9k patches coming in through this tree that have been acked by
 the wireless maintainers as they relied on the debugfs changes.
 
 Everything has been in linux-next for a while.
 
 Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v2
 
 iEYEABECAAYFAlSOD20ACgkQMUfUDdst+ylLPACg2QrW1oHhdTMT9WI8jihlHVRM
 53kAoLeteByQ3iVwWurwwseRPiWa8+MI
 =OVRS
 -----END PGP SIGNATURE-----

Merge tag 'driver-core-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core

Pull driver core update from Greg KH:
 "Here's the set of driver core patches for 3.19-rc1.

  They are dominated by the removal of the .owner field in platform
  drivers.  They touch a lot of files, but they are "simple" changes,
  just removing a line in a structure.

  Other than that, a few minor driver core and debugfs changes.  There
  are some ath9k patches coming in through this tree that have been
  acked by the wireless maintainers as they relied on the debugfs
  changes.

  Everything has been in linux-next for a while"

* tag 'driver-core-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (324 commits)
  Revert "ath: ath9k: use debugfs_create_devm_seqfile() helper for seq_file entries"
  fs: debugfs: add forward declaration for struct device type
  firmware class: Deletion of an unnecessary check before the function call "vunmap"
  firmware loader: fix hung task warning dump
  devcoredump: provide a one-way disable function
  device: Add dev_<level>_once variants
  ath: ath9k: use debugfs_create_devm_seqfile() helper for seq_file entries
  ath: use seq_file api for ath9k debugfs files
  debugfs: add helper function to create device related seq_file
  drivers/base: cacheinfo: remove noisy error boot message
  Revert "core: platform: add warning if driver has no owner"
  drivers: base: support cpu cache information interface to userspace via sysfs
  drivers: base: add cpu_device_create to support per-cpu devices
  topology: replace custom attribute macros with standard DEVICE_ATTR*
  cpumask: factor out show_cpumap into separate helper function
  driver core: Fix unbalanced device reference in drivers_probe
  driver core: fix race with userland in device_add()
  sysfs/kernfs: make read requests on pre-alloc files use the buffer.
  sysfs/kernfs: allow attributes to request write buffer be pre-allocated.
  fs: sysfs: return EGBIG on write if offset is larger than file size
  ...
2014-12-14 16:10:09 -08:00
Danielle Costantino ab0831d0f3 i2c: mpc: report correct I2C error return codes
This patch enforces correct I2C error returned codes from Freescale's
MPC i2c bus driver, allowing for proper user-space/kernel error
handling.

Signed-off-by: Danielle Costantino <danielle.costantino@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2014-11-12 16:34:11 +01:00
Wolfram Sang 1ecc4335eb i2c: busses: drop owner assignment from platform_drivers
A platform_driver does not need to set an owner, it will be populated by the
driver core.

Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2014-10-20 16:20:37 +02:00
Julia Lawall ebba48b702 i2c: mpc: delete unneeded test before of_node_put
Of_node_put supports NULL as its argument, so the initial test is not
necessary.

Suggested by Uwe Kleine-König.

The semantic patch that fixes this problem is as follows:
(http://coccinelle.lip6.fr/)

// <smpl>
@@
expression e;
@@

-if (e)
   of_node_put(e);
// </smpl>

Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2014-08-08 18:45:30 +02:00
Valentin Longchamp d49019a069 i2c: mpc: insert DR read in i2c_fixup()
The mpc_i2c_fixup function is called when the bus is not released by a
slave. The function generates 9 pulses that should lead the slave
to release the bus.

The sequence that generates the pulses disables/enables the I2C module
that controls the blocked bus. We have found out on the P2041 SoC that
this could cause the CPU to hang (for a short delay).

To avoid this, this patch introduces a read to the I2CDR register
between the re-enablement of the I2C module in master mode and its
returning to the slave mode instead of the delay (the final delay,
between the pulses is kept), as proposed in procedure from the P2041
reference manual (16.6.2.3), and the other manuals from the mpc83xx and
mpc85xx families.

Signed-off-by: Rainer Boschung <rainer.boschung@keymile.com>
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2014-06-03 14:24:16 +02:00
Paul Gortmaker 21d0b7c0fa i2c: delete non-required instances of include <linux/init.h>
None of these files are actually using any __init type directives
and hence don't need to include <linux/init.h>.  Most are just a
left over from __devinit and __cpuinit removal, or simply due to
code getting copied from one driver to the next.

Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Acked-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2014-01-24 18:24:31 +01:00
Rob Herring 5af5073004 drivers: clean-up prom.h implicit includes
Powerpc is a mess of implicit includes by prom.h. Add the necessary
explicit includes to drivers in preparation of prom.h cleanup.

Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Acked-by: Grant Likely <grant.likely@linaro.org>
2013-10-09 20:04:04 -05:00
Gerhard Sittig b3bfce2bc2 i2c: mpc: cleanup clock API use
make the MPC I2C driver get, prepare and enable the gated clock item for
register access during probe; disable and unprepare the clock upon
remove(), put is done by the devm approach; hold a reference to the
clock over the period of use

clock lookup is non-fatal in this implementation as not all platforms
may provide clock specs in their device tree, but failure to enable a
clock when specified is considered fatal

Signed-off-by: Gerhard Sittig <gsi@denx.de>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2013-08-28 10:48:44 +02:00
Wolfram Sang 687b81d083 i2c: move OF helpers into the core
I2C of helpers used to live in of_i2c.c but experience (from SPI) shows
that it is much cleaner to have this in the core. This also removes a
circular dependency between the helpers and the core, and so we can
finally register child nodes in the core instead of doing this manually
in each driver. So, fix the drivers and documentation, too.

Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2013-08-23 10:22:20 +02:00
Jingoo Han 0a488c49ea i2c: i2c-mpc: add CONFIG_PM_SLEEP to suspend/resume functions
Add CONFIG_PM_SLEEP to suspend/resume functions to fix the following
build warning when CONFIG_PM_SLEEP is not selected. This is because
sleep PM callbacks defined by SIMPLE_DEV_PM_OPS are only used when
the CONFIG_PM_SLEEP is enabled.

drivers/i2c/busses/i2c-mpc.c:724:12: warning: 'mpc_i2c_suspend' defined but not used [-Wunused-function]
drivers/i2c/busses/i2c-mpc.c:734:12: warning: 'mpc_i2c_resume' defined but not used [-Wunused-function]

Also, this patch makes mpc_i2c_pm_ops static, because mpc_i2c_pm_ops
is not exported.

Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2013-08-15 12:23:57 +02:00
Guenter Roeck 421476aeed i2c: mpc: Define unique I2C adapter names
The I2C adapters on Freescale MPC107/824x/85xx/512x/52xx/83xx/86xx all
have the same name "MPC adapter". Since I2C adapter numbers can change
across reboots and even after loading/unloading an I2C bus master driver,
adapter names have to be used to identify adapters and thus should be
unique and well defined. Since this is not the case with this driver,
it is difficult if not impossible to identify a specific adapter from
user space on affected platforms.

To remedy the problem, use the adapter memory address as part of the
adapter name.

With this patch, adapter names are:
On P2020:
MPC adapter at 0xfff703000
MPC adapter at 0xfff703100

On P5040:
MPC adapter at 0xffe118000
MPC adapter at 0xffe118100
MPC adapter at 0xffe119000
MPC adapter at 0xffe119100

Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2013-08-07 17:30:04 +02:00
Jingoo Han c2c6495472 i2c: use platform_{get,set}_drvdata()
Use the wrapper functions for getting and setting the driver data using
platform_device instead of using dev_{get,set}_drvdata() with &pdev->dev,
so we can directly pass a struct platform_device.

Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2013-06-12 20:39:07 +02:00
Doug Anderson 55827f4aa6 i2c: Remove unneeded xxx_set_drvdata(..., NULL) calls
There is simply no reason to be manually setting the private driver
data to NULL in the remove/fail to probe cases.  This is just extra
cruft code that can be removed.

A few notes:
* Nothing relies on drvdata being set to NULL.
* The __device_release_driver() function eventually calls
  dev_set_drvdata(dev, NULL) anyway, so there's no need to do it
  twice.
* I verified that there were no cases where xxx_get_drvdata() was
  being called in these drivers and checking for / relying on the NULL
  return value.

This could be cleaned up kernel-wide but for now just take the baby
step and remove from the i2c subsystem.

Reported-by: Wolfram Sang <wsa@the-dreams.de>
Reported-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Doug Anderson <dianders@chromium.org>
Reviewed-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Peter Korsgaard <jacmet@sunsite.dk>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Signed-off-by: Wolfram Sang <wolfram@the-dreams.de>
2013-02-22 00:25:50 +01:00
Bill Pemberton 0b255e927d i2c: remove __dev* attributes from subsystem
CONFIG_HOTPLUG is going away as an option.  As result the __dev*
markings will be going away.

Remove use of __devinit, __devexit_p, __devinitdata, __devinitconst,
and __devexit.

Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Acked-by: Peter Korsgaard <peter.korsgaard@barco.com> (for ocores and mux-gpio)
Acked-by: Havard Skinnemoen <hskinnemoen@gmail.com> (for i2c-gpio)
Acked-by: Guan Xuetao <gxt@mprc.pku.edu.cn> (for puf3)
Acked-by: Barry Song <baohua.song@csr.com> (for sirf)
Reviewed-by: Jean Delvare <khali@linux-fr.org>
[wsa: Fixed "foo* bar" flaws while we are here]
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
2012-12-22 20:13:45 +01:00
Linus Torvalds 12250d843e Merge branch 'i2c-embedded/for-next' of git://git.pengutronix.de/git/wsa/linux
Pull i2c-embedded changes from Wolfram Sang:
 "The changes for i2c-embedded include:

   - massive rework of the omap driver
   - massive rework of the at91 driver.  In fact, the old driver gets
     removed; I am okay with this approach since the old driver was
     depending on BROKEN and its limitations made it practically
     unusable, so people used bitbanging instead.  But even if there are
     users, there is no platform_data or module parameter which would
     need to be converted.  It is just another driver doing I2C
     transfers, just way better.  Modifications of arch/arm/at91 related
     files have proper acks from the maintainer.
   - new driver for R-Car I2C
   - devicetree and generic_clock conversions and fixes
   - usual driver fixes and changes.

  The rework patches have come a long way and lots of people have been
  involved in creating/testing them.  Most patches have been in
  linux-next at least since 3.6-rc5.  A few have been added in the last
  week, I have to admit.

  An unexpected (but welcome :)) peak in private life is the cause for
  that.  The "late" patches shouldn't cause any merge conflicts and I
  will have a special eye on them during the stabilization phase.  This
  is an exception and I want to have the patches in place properly in
  time again for the next kernels."

* 'i2c-embedded/for-next' of git://git.pengutronix.de/git/wsa/linux: (44 commits)
  MXS: Implement DMA support into mxs-i2c
  i2c: add Renesas R-Car I2C driver
  i2c: s3c2410: use clk_prepare_enable and clk_disable_unprepare
  ARM: OMAP: convert I2C driver to PM QoS for MPU latency constraints
  i2c: nomadik: Add Device Tree support to the Nomadik I2C driver
  i2c: algo: pca: Fix chip reset function for PCA9665
  i2c: mpc: Wait for STOP to hit the bus
  i2c: davinci: preparation for switch to common clock framework
  omap-i2c: fix incorrect log message when using a device tree
  i2c: omap: sanitize exit path
  i2c: omap: switch over to autosuspend API
  i2c: omap: remove unnecessary pm_runtime_suspended check
  i2c: omap: switch to threaded IRQ support
  i2c: omap: remove redundant status read
  i2c: omap: get rid of the "complete" label
  i2c: omap: resize fifos before each message
  i2c: omap: simplify IRQ exit path
  i2c: omap: always return IRQ_HANDLED
  i2c: omap: simplify errata check
  i2c: omap: bus: add a receiver flag
  ...
2012-10-11 10:27:51 +09:00
Joakim Tjernlund 0c25aefa35 i2c: mpc: Wait for STOP to hit the bus
mpc_i2c_stop() only initiates STOP but does not wait for it to
hit the I2C bus. This is a problem when using I2C devices which
uses fairly long clock stretching just before STOP if you also
have an i2c-mux which may switch to another bus before STOP has
been processed.

Signed-off-by: Joakim Tjernlund <Joakim.Tjernlund@transmode.se>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
2012-09-14 16:01:04 +02:00
Arnd Bergmann 1d10a65fde i2c/mpc: make data used as *of_device_id.data const
Since of_device_id.data is declared as a pointer to const data a few
more consts can be added in this driver.

[ukl: split Arnd's patch by driver]

Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
2012-09-11 08:57:37 +02:00
Uwe Kleine-König 215e691c2a i2c/mpc: add a const qualifier
This prepares *of_device_id.data becoming const. Without this change
the following warning would occur:

	drivers/i2c/busses/i2c-mpc.c: In function 'fsl_i2c_probe':
	drivers/i2c/busses/i2c-mpc.c:650:31: warning: initialization discards 'const' qualifier from pointer target type [enabled by default]

Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
2012-09-11 08:56:48 +02:00
Zhao Chenhui 531183e5d2 i2c-mpc: avoid I2C abnormal after resuming from deep sleep
When entering deep sleep, the value in the registers I2CFDR and
I2CDFSRR are lost. This causes I2C access to fail after resuming.

Add suspend/resume routines to save/restore the registers
I2CFDR and I2CDFSRR.

Signed-off-by: Zhao Chenhui <chenhui.zhao@freescale.com>
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
2012-05-12 14:28:12 +02:00
Tang Yuantian 3f0e1e4bb6 i2c: mpc: Add support for SMBUS_READ_BLOCK_DATA
Add support for SMBUS_READ_BLOCK_DATA to the i2c-mpc bus driver.

Signed-off-by: Tang Yuantian <Yuantian.Tang@freescale.com>
Cc: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
2012-02-24 22:25:30 +01:00
Axel Lin a3664b51c7 i2c/busses: Use module_platform_driver()
Convert the drivers in drivers/i2c/busses/* to use the
module_platform_driver() macro which makes the code smaller and a bit
simpler.

Cc: Ben Dooks <ben-linux@fluff.org>
Acked-by: Jochen Friedrich <jochen@scram.de>
Acked-by: Peter Korsgaard <jacmet@sunsite.dk>
Acked-by: Wolfram Sang <w.sang@pengutronix.de>
Cc: Manuel Lauss <manuel.lauss@googlemail.com>
Cc: Barry Song <21cnbao@gmail.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Yong Zhang <yong.zhang0@gmail.com>
Cc: Lucas De Marchi <lucas.demarchi@profusion.mobi>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
2012-01-12 20:32:04 +01:00
Grant Likely b1608d69cb drivercore: revert addition of of_match to struct device
Commit b826291c, "drivercore/dt: add a match table pointer to struct
device" added an of_match pointer to struct device to cache the
of_match_table entry discovered at driver match time.  This was unsafe
because matching is not an atomic operation with probing a driver.  If
two or more drivers are attempted to be matched to a driver at the
same time, then the cached matching entry pointer could get
overwritten.

This patch reverts the of_match cache pointer and reworks all users to
call of_match_device() directly instead.

Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
2011-05-18 12:32:23 -06:00
Grant Likely 1c48a5c93d dt: Eliminate of_platform_{,un}register_driver
Final step to eliminate of_platform_bus_type.  They're all just
platform drivers now.

v2: fix type in pasemi_nand.c (thanks to Stephen Rothwell)

Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
2011-02-28 13:22:46 -07:00
Grant Likely 925bb9c649 of/i2c: Fix module load order issue caused by of_i2c.c
Commit 959e85f7, "i2c: add OF-style registration and binding" caused a
module dependency loop where of_i2c.c calls functions in i2c-core, and
i2c-core calls of_i2c_register_devices() in of_i2c.  This means that
when i2c support is built as a module when CONFIG_OF is set, then
neither i2c_core nor of_i2c are able to be loaded.

This patch fixes the problem by moving the of_i2c_register_devices()
calls back into the device drivers.  Device drivers already
specifically request the core code to parse the device tree for
devices anyway by setting the of_node pointer, so it isn't a big
deal to also call the registration function.  The drivers just become
slightly more verbose.

Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
2010-09-30 14:14:23 +02:00
Grant Likely 2dc1158137 of/device: Replace struct of_device with struct platform_device
of_device is just an alias for platform_device, so remove it entirely.  Also
replace to_of_device() with to_platform_device() and update comment blocks.

This patch was initially generated from the following semantic patch, and then
edited by hand to pick up the bits that coccinelle didn't catch.

@@
@@
-struct of_device
+struct platform_device

Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Reviewed-by: David S. Miller <davem@davemloft.net>
2010-08-06 09:25:50 -06:00
Linus Torvalds 03c0c29aff Merge branch 'next-devicetree' of git://git.secretlab.ca/git/linux-2.6
* 'next-devicetree' of git://git.secretlab.ca/git/linux-2.6: (63 commits)
  of/platform: Register of_platform_drivers with an "of:" prefix
  of/address: Clean up function declarations
  of/spi: call of_register_spi_devices() from spi core code
  of: Provide default of_node_to_nid() implementation.
  of/device: Make of_device_make_bus_id() usable by other code.
  of/irq: Fix endian issues in parsing interrupt specifiers
  of: Fix phandle endian issues
  of/flattree: fix of_flat_dt_is_compatible() to match the full compatible string
  of: remove of_default_bus_ids
  of: make of_find_device_by_node generic
  microblaze: remove references to of_device and to_of_device
  sparc: remove references to of_device and to_of_device
  powerpc: remove references to of_device and to_of_device
  of/device: Replace of_device with platform_device in includes and core code
  of/device: Protect against binding of_platform_drivers to non-OF devices
  of: remove asm/of_device.h
  of: remove asm/of_platform.h
  of/platform: remove all of_bus_type and of_platform_bus_type references
  of: Merge of_platform_bus_type with platform_bus_type
  drivercore/of: Add OF style matching to platform bus
  ...

Fix up trivial conflicts in arch/microblaze/kernel/Makefile due to just
some obj-y removals by the devicetree branch, while the microblaze
updates added a new file.
2010-08-05 15:57:35 -07:00
Albrecht Dreß 0c2daaafcd powerpc/5200/i2c: improve i2c bus error recovery
This patch improves the recovery of the MPC's I2C bus from errors like bus
hangs resulting in timeouts:
1. make the bus timeout configurable, as it depends on the bus clock and
    the attached slave chip(s); default is still 1 second;
2. detect any of the cases indicated by the CF, BB and RXAK MSR flags if a
    timeout occurs, and add a missing (required) MAL reset;
3. use a more reliable method to fixup the bus if a hang has been detected.
    The sequence is sent 9 times which seems to be necessary if a slave
    "misses" more than one clock cycle.  For 400 kHz bus speed, the fixup is
    also ~70us (81us vs. 150us) faster.

Tested on a custom Lite5200b derived board, with a Dallas RTC, AD sensors
and NXP IO expander chips attached to the i2c.

Changes vs. v1:
- use improved bus fixup sequence for all chips (not only the 5200)
- calculate real clock from defaults if no clock is given in the device tree
- better description (I hope) of the changes.

I didn't split the changes in this file into three parts as recommended by
Grant, as they actually belong together (i.e. they address one single
problem, just in three places of one single source file).

Signed-off-by: Albrecht Dreß <albrecht.dress@arcor.de>
[grant.likely@secretlab.ca: fixup for ->node to ->dev.of_node transition]
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
2010-08-01 17:06:44 -06:00
Grant Likely 959e85f775 i2c: Add OF-style registration and binding
This patch adds OF hooks to the i2c core so that devices can automatically
be registered based on device tree data.

Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
2010-07-05 16:14:52 -06:00
Grant Likely 9fd049927c of/i2c: Generalize OF support
This patch cleans up the i2c OF support code to make it selectable by
all architectures and allow for automatic registration of i2c devices.

Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
2010-07-05 16:14:52 -06:00
Grant Likely cf9b59e9d3 Merge remote branch 'origin' into secretlab/next-devicetree
Merging in current state of Linus' tree to deal with merge conflicts and
build failures in vio.c after merge.

Conflicts:
	drivers/i2c/busses/i2c-cpm.c
	drivers/i2c/busses/i2c-mpc.c
	drivers/net/gianfar.c

Also fixed up one line in arch/powerpc/kernel/vio.c to use the
correct node pointer.

Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
2010-05-22 00:36:56 -06:00
Grant Likely 4018294b53 of: Remove duplicate fields from of_platform_driver
.name, .match_table and .owner are duplicated in both of_platform_driver
and device_driver.  This patch is a removes the extra copies from struct
of_platform_driver and converts all users to the device_driver members.

This patch is a pretty mechanical change.  The usage model doesn't change
and if any drivers have been missed, or if anything has been fixed up
incorrectly, then it will fail with a compile time error, and the fixup
will be trivial.  This patch looks big and scary because it touches so
many files, but it should be pretty safe.

Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Sean MacLennan <smaclennan@pikatech.com>
2010-05-22 00:10:40 -06:00
Wolfram Sang bf727e016f i2c-mpc: drop NO_IRQ
Drop NO_IRQ as 0 is the preferred way to describe 'no irq'
(http://lkml.org/lkml/2005/11/21/221). This change is safe, as the driver is
only used on powerpc, where NO_IRQ is 0 anyhow.

Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Cc: Ben Dooks <ben-linux@fluff.org>
2010-05-20 00:19:01 +01:00
Grant Likely 61c7a080a5 of: Always use 'struct device.of_node' to get device node pointer.
The following structure elements duplicate the information in
'struct device.of_node' and so are being eliminated.  This patch
makes all readers of these elements use device.of_node instead.

(struct of_device *)->node
(struct dev_archdata *)->prom_node (sparc)
(struct dev_archdata *)->of_node (powerpc & microblaze)

Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
2010-05-18 16:10:44 -06:00
Tejun Heo 5a0e3ad6af include cleanup: Update gfp.h and slab.h includes to prepare for breaking implicit slab.h inclusion from percpu.h
percpu.h is included by sched.h and module.h and thus ends up being
included when building most .c files.  percpu.h includes slab.h which
in turn includes gfp.h making everything defined by the two files
universally available and complicating inclusion dependencies.

percpu.h -> slab.h dependency is about to be removed.  Prepare for
this change by updating users of gfp and slab facilities include those
headers directly instead of assuming availability.  As this conversion
needs to touch large number of source files, the following script is
used as the basis of conversion.

  http://userweb.kernel.org/~tj/misc/slabh-sweep.py

The script does the followings.

* Scan files for gfp and slab usages and update includes such that
  only the necessary includes are there.  ie. if only gfp is used,
  gfp.h, if slab is used, slab.h.

* When the script inserts a new include, it looks at the include
  blocks and try to put the new include such that its order conforms
  to its surrounding.  It's put in the include block which contains
  core kernel includes, in the same order that the rest are ordered -
  alphabetical, Christmas tree, rev-Xmas-tree or at the end if there
  doesn't seem to be any matching order.

* If the script can't find a place to put a new include (mostly
  because the file doesn't have fitting include block), it prints out
  an error message indicating which .h file needs to be added to the
  file.

The conversion was done in the following steps.

1. The initial automatic conversion of all .c files updated slightly
   over 4000 files, deleting around 700 includes and adding ~480 gfp.h
   and ~3000 slab.h inclusions.  The script emitted errors for ~400
   files.

2. Each error was manually checked.  Some didn't need the inclusion,
   some needed manual addition while adding it to implementation .h or
   embedding .c file was more appropriate for others.  This step added
   inclusions to around 150 files.

3. The script was run again and the output was compared to the edits
   from #2 to make sure no file was left behind.

4. Several build tests were done and a couple of problems were fixed.
   e.g. lib/decompress_*.c used malloc/free() wrappers around slab
   APIs requiring slab.h to be added manually.

5. The script was run on all .h files but without automatically
   editing them as sprinkling gfp.h and slab.h inclusions around .h
   files could easily lead to inclusion dependency hell.  Most gfp.h
   inclusion directives were ignored as stuff from gfp.h was usually
   wildly available and often used in preprocessor macros.  Each
   slab.h inclusion directive was examined and added manually as
   necessary.

6. percpu.h was updated not to include slab.h.

7. Build test were done on the following configurations and failures
   were fixed.  CONFIG_GCOV_KERNEL was turned off for all tests (as my
   distributed build env didn't work with gcov compiles) and a few
   more options had to be turned off depending on archs to make things
   build (like ipr on powerpc/64 which failed due to missing writeq).

   * x86 and x86_64 UP and SMP allmodconfig and a custom test config.
   * powerpc and powerpc64 SMP allmodconfig
   * sparc and sparc64 SMP allmodconfig
   * ia64 SMP allmodconfig
   * s390 SMP allmodconfig
   * alpha SMP allmodconfig
   * um on x86_64 SMP allmodconfig

8. percpu.h modifications were reverted so that it could be applied as
   a separate patch and serve as bisection point.

Given the fact that I had only a couple of failures from tests on step
6, I'm fairly confident about the coverage of this conversion patch.
If there is a breakage, it's likely to be something in one of the arch
headers which should be easily discoverable easily on most builds of
the specific arch.

Signed-off-by: Tejun Heo <tj@kernel.org>
Guess-its-ok-by: Christoph Lameter <cl@linux-foundation.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
2010-03-30 22:02:32 +09:00
Wolfgang Grandegger f00d738f04 i2c-mpc: add support for the MPC512x processors from Freescale
As I2C interrupts must  be enabled for the MPC512x by the setup function
as well, "fsl,preserve-clocking" is handled in a slighly different way.
Also, the old settings are now reported calling dev_dbg(). For the
MPC512x the clock setup function of the MPC52xx can be re-used.
Furthermore, the Kconfig help has been updated and corrected.

Signed-off-by: Wolfgang Grandegger <wg@denx.de>
Reviewed-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
2010-03-07 22:03:09 +00:00
Wolfgang Grandegger a93522116e i2c-mpc: rename "setclock" initialization functions to "setup"
To prepare  support for the MPC512x processors from Freescale the
"setclock" initialization functions have been renamed to "setup"
because I2C interrupts must be enabled for the MPC512x by this
function as well.

Signed-off-by: Wolfgang Grandegger <wg@denx.de>
Acked-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
2010-03-07 22:03:09 +00:00
Wolfgang Grandegger 6e56dd3d0e i2c-mpc: use __devinit[data] for initialization functions and data
"__devinit[data]" has not yet been used for all initialization functions
and data. To avoid truncating lines, the struct "mpc_i2c_match_data" has
been renamed to "mpc_i2c_data", which is even the better name.

Signed-off-by: Wolfgang Grandegger <wg@denx.de>
Tested-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
2010-03-07 22:03:09 +00:00
Joakim Tjernlund 45da790ebe i2c-mpc: Do not generate STOP after read.
The driver always ends a read with a STOP condition which
breaks subsequent I2C reads/writes in the same transaction as
these expect to do a repeated START(ReSTART).

This will also help I2C multimaster as the bus will not be released
after the first read, but when the whole transaction ends.

Signed-off-by: Joakim Tjernlund <Joakim.Tjernlund@transmode.se>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
2009-11-02 23:28:47 +00:00
Wolfgang Denk 87c441e54d powerpc/5xxx: Add common mpc5xxx_get_bus_frequency() function
So far, MPC512x used mpc512x_find_ips_freq() to get the bus frequency,
while MPC52xx used mpc52xx_find_ipb_freq().  Despite the different
clock names (IPS vs. IPB) the code was identical.

Use common code for both processor families.

Signed-off-by: Wolfgang Denk <wd@denx.de>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
2009-06-17 00:30:22 -06:00
Wolfgang Grandegger 1904b03430 i2c-mpc: bug fix for MPC52xx clock setting and printout
The clock setting did not work for the MPC52xx due to a stupid bug.
Furthermore, the dev info output "clock=0" for old device trees was
misleading. This patch fixes both issues.

Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
2009-05-12 00:35:56 +01:00