Instead of having two copies of the code for device tree cfgdata
downloading, add a function to improve the code.
Reviewed-by: Paul Stewart <pstew@chromium.org>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If cfgdata length exceeds the command buffer size we will end up
getting buffer overflow problem. Fix it by checking the buffer
size less the command header length.
Reviewed-by: Paul Stewart <pstew@chromium.org>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
As soon as skb is ready to be reaped, prefetch 1-st cache line.
This accelerates data access that is performed later, during the
packet classification by the driver and IP stack.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Bit DMA_CFG_DESC_TX_OFFLOAD_CFG_L3T_IPV4_POS should be set for IPv4
only. Don't set it for IPv6
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use hardware capabilities to limit IRQ generation to about 15 per msec
It corresponds to about 7 packets/IRQ when running iperf with default
parameters at 1.3Gbps
Do not enable this feature in the sniffer (monitor) mode, because
interrupt moderation cause timestamp accuracy deterioration.
For the sniffer flow, it is important to get precise timestamp.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds support for the bcm43362 1x1 11n chipset. This
chipset is used in AP6210 wifi module found on Cubieboard [1].
[1] http://cubieboard.org/
Reviewed-by: Franky Lin <frankyl@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add nvs file name to module firmware list
Signed-off-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The firmware doesn't support per packet encryption selection, so disable hw
encryption support completely while a monitor interface is present to support
injection of packets (which shouldn't get encrypted by hw).
To enforce the changed hw encryption support force a disassociation on
non-monitor interfaces.
For disassociation a workaround using hw connection monitor is employed,
which temporary enables hw connection manager flag.
Signed-off-by: David Gnedt <david.gnedt@davizone.at>
Signed-off-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Set the retry limit to 0 and disable the ACK policy for injected packets.
Signed-off-by: David Gnedt <david.gnedt@davizone.at>
Signed-off-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If necessary enable the tx path in monitor mode for packet injection using
the JOIN command with BSS_TYPE_STA_BSS and zero BSSID.
Signed-off-by: David Gnedt <david.gnedt@davizone.at>
Signed-off-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use the ENABLE_RX command for channel switching when no interface is present
(monitor mode only).
The advantage of ENABLE_RX is that it leaves the tx data path disabled in
firmware, whereas the usual JOIN command seems to transmit some frames at
firmware level.
Signed-off-by: David Gnedt <david.gnedt@davizone.at>
Signed-off-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Force power saving off while monitor interface is present.
Signed-off-by: David Gnedt <david.gnedt@davizone.at>
Signed-off-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Port multicast address filtering from wl1271 driver.
It sets up the hardware multicast address filter in configure_filter() with
addresses supplied through prepare_multicast().
Signed-off-by: David Gnedt <david.gnedt@davizone.at>
Signed-off-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Disable hardware encryption (DF_ENCRYPTION_DISABLE) and decryption
(DF_SNIFF_MODE_ENABLE) via wl1251_acx_feature_cfg while monitor interface is
present.
Signed-off-by: David Gnedt <david.gnedt@davizone.at>
Signed-off-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Split up data path initialisation into RX and TX data path initialisation
functions. This change is required for channel switching in monitor mode.
Signed-off-by: David Gnedt <david.gnedt@davizone.at>
Signed-off-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Update hardware ARP filter configuration on BSS_CHANGED_ARP_FILTER
notification from mac80211.
Ported from wl1271 driver.
Signed-off-by: David Gnedt <david.gnedt@davizone.at>
Signed-off-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Port of the power save entry retry code from wl1251 driver version included
in the Maemo Fremantle kernel.
This tries to enable power save mode up to 3 times before failing.
Signed-off-by: David Gnedt <david.gnedt@davizone.at>
Signed-off-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
With a dissasociated card I often encoutered very long scan delays.
My guess is that it has something to do with the cards DTIM handling and
another firmware bug mentioned in the TI WLAN driver, which is described as
the card may never end scanning if the channel is overloaded because it
can't send probe requests. I think the firmware somehow also tries to
receive DTIM messages when the BSSID is not set. Therefore most of the time
it waits for DTIM messages and can't do scanning work.
Anyway we can workaround this misbehaviour by setting the HIGH_PRIORITY
bit for scans in disassociated state.
Signed-off-by: David Gnedt <david.gnedt@davizone.at>
Signed-off-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The driver needs to set the MFP flag earlier in i40e_sw_init
and then can use that flag to decide if other hardware
work-arouds are required.
Change-ID: Ib17ad1e3485f57b28845ab4722294a99f203bd48
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The hardware requires a full packet template to be pointed to when adding
hardware flow filters. This patch adds the template and uses it for
programming filters.
Change-ID: I09db9f4ab0207ca9c520ae36596d74e1a0663ae5
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Fix some badly formatted lines, long lines and a mis-formatted else.
Change-ID: Iac2eef064ae27c55a0c3d9c15c525bf8fed8ab6f
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The alloc_rx_buff_failed and alloc_rx_page_failed variables
are both part of an rx specific structure so just remove
the _rx part of the name. No functional changes.
Change-ID: Icffa2f5d13c6f2b1e09cf45b9472b83c9dae8fc6
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The admin queue can be used to send messages among the physical
function interfaces. This adds the code to handle that case.
Change-ID: I0700fcc47e41433131a381f0eb72fc7b01b6bd87
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Since nearly everything we do is synchronous, using the interrupt-on-error bit
is unnecessary and causing unneeded interrupts. If anyone wants to use the bit
they can turn it on in individual AQ requests using the cmd_details parameter.
Change-ID: I4690a9c561d3e0836aeadb4f88f8a8702b1d1366
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Call AQ to release any reservation held by this PF on the NVM resource
lock on startup, in order to clear anything that might have been left over from
a previous run. The lock is only cleared by the requestor calling for it to be
cleared, on power-on, or firmware reset. This should help limit the need for
rebooting a customer machine if something goes wrong on a firmware update or
some other action.
Change-ID: I8c8473e601d4ef512dda7baa77a6e75f2e5fea49
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
RSS initialization was doing some extra work, remove the extra
work and any bugs it created when managing number of queues.
Change-ID: Iea75b04a70d73ce76947b6a177ce89ab4899d4c6
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The driver and hardware support splitting packets on headers
but with the use of GRO we don't need the extra bus
overhead, so make this driver more like igb and ixgbe and
disable packet split.
Change-ID: Id42f2c3736baa9d5bdfe1f72d64226e7d8ebd737
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The memory barrier used in maybe_stop_tx can use a comment.
Also add checks to VSI->rx_rings to ensure a kernel panic is not induced.
Change-ID: I48cc1bf1d6cf301818155b737edeef77c0d790c7
Change-ID: I1363a8445fbf521a26267849966296ed55f43ad8
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The MAC address format expected by the hardware is in a very specific
format, and the driver was filling in the data incorrectly.
Change-ID: I7bc66505ef459ee347dd3bda68051004c141c689
Signed-off-by: Kamil Krawczyk <kamil.krawczyk@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The GPL header included in each file in the i40e driver doesn't
need to include the "this program" text since this driver
is already part of the larger kernel.
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The hardware can occasionally give an interrupt on the misc
queue for which there is no driver work to do. In that case
the driver was not re-enabling interrupts even though they
were auto masked by hardware. This left interrupts disabled
on this queue.
Re-enable the interrupt whenever leaving this function.
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Pablo Neira Ayuso says:
====================
Netfilter updates for net-next
The following patchset contains three Netfilter updates, they are:
* Fix wrong usage of skb_header_pointer in the DCCP protocol helper that
has been there for quite some time. It was resulting in copying the dccp
header to a pointer allocated in the stack. Fortunately, this pointer
provides room for the dccp header is 4 bytes long, so no crashes have been
reported so far. From Daniel Borkmann.
* Use format string to print in the invocation of nf_log_packet(), again
in the DCCP helper. Also from Daniel Borkmann.
* Revert "netfilter: avoid get_random_bytes call" as prandom32 does not
guarantee enough entropy when being calling this at boot time, that may
happen when reloading the rule.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
If a broadcast packet is coming from a client marked as
isolated, then mark the skb using the isolation mark so
that netfilter (or any other application) can recognise
them.
The mark is written in the skb based on the mask value:
only bits set in the mask are substitued by those in the
mark value
Signed-off-by: Antonio Quartulli <antonio@open-mesh.com>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
The AP isolation status may be evaluated in different spots.
Create an helper function to avoid code duplication.
Signed-off-by: Antonio Quartulli <antonio@open-mesh.com>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Change the AP isolation mechanism to not only "isolate" WIFI
clients but also all those marked with the more generic
"isolation flag" (BATADV_TT_CLIENT_ISOLA).
The result is that when AP isolation is on any unicast
packet originated by an "isolated" client and directed to
another "isolated" client is dropped at the source node.
Signed-off-by: Antonio Quartulli <antonio@open-mesh.com>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Print the new BATADV_TT_CLIENT_ISOLA flag properly in the
Local and Global Translation Table output.
The character 'I' is used in the flags column to indicate
that the entry is marked as isolated.
Signed-off-by: Antonio Quartulli <antonio@open-mesh.com>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
A client sending packets which mark matches the value
configured via sysfs has to be identified as isolated using
the TT_CLIENT_ISOLA flag.
The match is mask based, meaning that only bits set in the
mask are compared with those in the mark value.
If the configured mask is equal to 0 no operation is
performed.
Such flag is then advertised within the classic client
announcement mechanism.
Signed-off-by: Antonio Quartulli <antonio@open-mesh.com>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
This attribute can be used to set and read the value and the
mask of the skb mark which will be used to classify the
source non-mesh client as ISOLATED. In this way a client can
be advertised as such and the mark can potentially be
restored at the receiving node before delivering the skb.
This can be helpful for creating network wide netfilter
policies.
This sysfs file expects a string of the shape "$mark/$mask".
Where $mark has to be a 32-bit number in any base, while
$mask must be a 32bit mask expressed in hex base. Only bits
in $mark covered by the bitmask are really stored.
Signed-off-by: Antonio Quartulli <antonio@open-mesh.com>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
In different situations it is possible that the DHCP server
or client uses broadcast Ethernet frames to send messages
to each other. The GW component in batman-adv takes care of
using bat-unicast packets to bring broadcast DHCP
Discover/Requests to the "best" server.
On the way back the DHCP server usually sends unicasts,
but upon client request it may decide to use broadcasts as
well.
This patch improves the GW component so that it now snoops
and sends as unicast all the DHCP packets, no matter if they
were generated by a DHCP server or client.
Signed-off-by: Antonio Quartulli <antonio@open-mesh.com>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Remove parenthesis around return expression as suggested by
checkpatch.
Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
The function batadv_gw_deselect() is actually not deselecting
anything. It is just informing the GW code to perform a
re-election procedure when possible.
The current gateway is not being touched at all and therefore
the name of this function is rather misleading.
Rename it to batadv_gw_reselect() to batadv_gw_reselect()
to make its behaviour easier to grasp.
Signed-off-by: Antonio Quartulli <antonio@open-mesh.com>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
When switching from gw_mode client to either off or server
the current selected gateway has to be deselected.
In this way when client mode is enabled again a gateway
re-election is forced and a GW_ADD event is consequently
sent.
The current behaviour instead is to keep the current gateway
leading to no GW_ADD event when gw_mode client is selected
for a second time
Signed-off-by: Antonio Quartulli <antonio@open-mesh.com>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
As suggested by checkpatch, remove all the references to the
FSF address since the kernel already has one reference in
its documentation.
In this way it is easier to update it in case of future
changes.
Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
If possible, operations like ntohs/ntohl should not be
performed too often. Use a variable to locally store the
converted value and then use it.
Signed-off-by: Antonio Quartulli <antonio@open-mesh.com>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
Jeff Kirsher says:
====================
Intel Wired LAN Driver Updates
This series contains updates to i40e only.
Anjali adds more functionality to debugfs to assist development and
testing of admin queue commands.
Greg makes sure broadcast promiscuous is disabled by default, otherwise
VLAN tagged packets out of the assigned VLAN domain are received. Also
provides a fix when the 8021q driver is loaded, so that VLAN 0 tagged
packets are accepted so that upper layers can interpret the priority
bits. Then provides a fix to let the VF to request the PF to set its
already assigned MAC address without generating an error. Greg also
adds helper functions to enable or disable internal switch loopback
when VFs are created or destroyed via the sysfs interface.
Shannon provides most of the changes, where he adds code to ensure
that the hardware waits to make sure that the firmware is ready as well
after reset. Also updates the code to use the new features in the
firmware. Provides a fix while in MFP mode where resources are
reduced, so use a smaller range of test registers than when in SFP mode.
Moves the PF ID initialization code to earlier in the driver
initialization function since a few operations need the information
before the first PF reset is called. Shannon adds a check for MAC
type before reading anything from the registers to ensure we dealing
with the correct MAC type. Then reworks Shadow RAM read word/buffer
functions as to not block whole NVM resources for SR read operations.
Mitch lastly provides a fix to correctly setup ARQ descriptors in
the cleanup code.
Catherine bumps the driver version due to all the recent changes.
v2:
- Added blank lines after local variable declarations to patch 01
as suggested by David Miller
- Used the suggested memset() line in patch 15 as suggested by David
Miller
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Bing Zhao
Vladimir Kondratiev
Arend van Spriel
Pavel Machek
David Gnedt
Catherine Sullivan
Jesse Brandeburg
Mitch Williams
Shannon Nelson
Anjali Singhai Jain
Greg Rose
Kamil Krawczyk
David S. Miller
Antonio Quartulli
Antonio Quartulli
John W. Linville