A sysfs function call uses the wrong parameter, and thus breaks a build on
SGI O2.
CC drivers/video/gbefb.o
drivers/video/gbefb.c: In function ‘gbefb_remove’:
drivers/video/gbefb.c:1246: error: ‘dev’ undeclared (first use in this function)
drivers/video/gbefb.c:1246: error: (Each undeclared identifier is reported only once
drivers/video/gbefb.c:1246: error: for each function it appears in.)
make[2]: *** [drivers/video/gbefb.o] Error 1
Signed-off-by: Joshua Kinard <kumba@gentoo.org>
Signed-off-by: Antonino Daplas <adaplas@pol.net>
Signed-off-by: Martin Michlmayr <tbm@cyrius.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch fixes a number of bugs in the authentication process:
1) When falling back to Shared Key authentication mode from Open System,
a missing 'return' would cause the auth request to be sent, but would
drop the card into Management Error state. When falling back, the
driver should also indicate that it is switching to Shared Key mode by
setting exclude_unencrypted.
2) Initial authentication modes were apparently wrong in some cases,
causing the driver to attempt Shared Key authentication mode when in
fact the access point didn't support that mode or even had WEP disabled.
The driver should set the correct initial authentication mode based on
wep_is_on and exclude_unencrypted.
3) Authentication response packets from the access point in Open System
mode were getting ignored because the driver was expecting the sequence
number of a Shared Key mode response. The patch separates the OS and SK
mode handling to provide the correct behavior.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The previous patch that added ENCODEEXT and AUTH support to the atmel
driver contained a slight error which would cause just setting the TX
key index to also set the encryption key again. This patch allows any
combination of setting the TX key index and setting an encryption key.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Below this point, the error path will proceed through
sis190_release_board(). It will happily oops if
pci_set_drvdata() has not been issued.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
If a data transfer is small (less than a FIFO size) we would
hang waiting for the data to be read due to the PIO interrupt
not occuring. We allowed for this in our PIO interrupt handler,
but not when setting up a data transfer.
Apply the "fix" when setting up a data transfer as well.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
We're getting some softlockup false positives during heavy PIO operations. So
poke the lockup detector.
Cc: Bartlomiej Zolnierkiewicz <B.Zolnierkiewicz@elka.pw.edu.pl>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
There were two mistakes in the register-read-on-(un)blank approach.
- First, without proper register (un)locking the value read back will always
be zero, and this is what I missed entirely until just now. Due to this,
the logic could not be verified at all and I tried some bogus checks which
are completely stupid.
- Second, the LCD status bit will always be set to zero when the backlight
has been turned off. Reading the value back during unblank will disable the
LCD unconditionally, regardless of the state it is supposed to be in, since
we set it to zero beforehand.
So this is what we do now:
- create a new variable in struct neofb_par, and use that to determine
whether to read back registers (initialized to true)
- before actually blanking the screen, read back the register to sense any
possible change made through Fn key combo
- use proper neoUnlock() / neoLock() to actually read something
- every call to neofb_blank() determines if we read back next time: blanking
disables readback, unblanking (FB_BLANK_UNBLANK) enables it
This should give us a nice and clean state machine. Has been thoroughly
tested on a Dell Latitude CPiA / NM220 Chip docked to a C/Dock2 with attached
CRT in all possible combinations of LCD/CRT on/off. I changed the config via
Fn key, let the console blank, unblanked by keypress - works flawlessly.
Signed-off-by: Christian Trefzer <ctrefzer@gmx.de>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
In kernel bugzilla #5176 (http://bugzilla.kernel.org/show_bug.cgi?id=5176)
Harry R\374ter <h.rueter@gmx.de> points out Documentation/jsm.txt is missing.
No one at Digi seems to care, so just remove the stale reference.
Signed-off-by: Arthur Othieno <apgo@patchbomb.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
98kbd{,-io} and 98spkr all went out with PC98 subarch. Remove stale Makefile
entries that remained.
Signed-off-by: Arthur Othieno <apgo@patchbomb.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
This updates the ads7846 touchscreen driver:
- to allow faster clocking (this driver doesn't push sample rates);
- bugfixes the conversion of spi_transfer to lists;
- some dma-unsafe command buffers are fixed.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Add Logitech mouse type 99 (Premium Optical Wheel Mouse, model M-BT58,
plain 3 buttons + wheel) to cure the following message: logips2pp: Detected
unknown logitech mouse model 99
Signed-off-by: Meelis Roos <mroos@linux.ee>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Fix issues with the NeoMagic framebuffer driver.
It nicely complements my previous fix already in linus' tree. The only
thing missing now is that the external CRT will not be activated at neofb
init when external-only is selected, either by register read or
module/kernel parameter.
Testing was done on a Dell Latitude CPi-A/NM2200 chip.
Previous behaviour:
- before booting linux, set the preferred display config X via FN+F8
- boot linux, neofb stores the register values in a private
variable
- change the display config to Y via keystroke
- leave the machine in peace until display is blanked
- touching any key will result in display config X being restored
- booting up, the BIOS will acknowledge config Y, though...
Current behaviour:
At the time of unblanking, config Y is honoured because we now read back
register contents instead of just overwriting them with outdated values.
Signed-off by: Christian Trefzer <ctrefzer@gmx.de>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The changes in the tty related code introduced wrong parenthesis in a if
condition in the isdn_tty_at_cout function. This caused access to index -1
in the dev->drv[] array. This patch change it back to the correct
condition from the previous versions.
Signed-off-by: Karsten Keil <kkeil@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
When the _CRS for a single HPET contains multiple EXTENDED_IRQ resources,
we overwrote hdp->hd_nirqs every time we found one.
So the driver worked when all the IRQs were described in a single
EXTENDED_IRQ resource, but failed when multiple resources were used.
(Strictly speaking, I think the latter is actually more correct, but both
styles have been used.)
Someday we should remove all the ACPI stuff from hpet.c and use PNP driver
registration instead. But currently PNP_MAX_IRQ is 2, and HPETs often have
more IRQs. Hint, hint, Adam :-)
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Acked-by: Bob Picco <robert.picco@hp.com>
Cc: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Cc: Len Brown <len.brown@intel.com>
Cc: Adam Belay <ambx1@neo.rr.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix hole where tty structure can be released when reference count is non
zero. Existing code can sleep without tty_sem protection between deciding
to release the tty structure (setting local variables tty_closing and
otty_closing) and setting TTY_CLOSING to prevent further opens. An open
can occur during this interval causing release_dev() to free the tty
structure while it is still referenced.
This should fix bugzilla.kernel.org [Bug 6041] New: Unable to handle kernel
paging request
In Bug 6041, tty_open() oopes on accessing the tty structure it has
successfully claimed. Bug was on SMP machine with the same tty being
opened and closed by multiple processes, and DEBUG_PAGEALLOC enabled.
Signed-off-by: Paul Fulghum <paulkf@microgate.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Jesper Juhl <jesper.juhl@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Reduce stack usage in the pkt_start_write() function. Even though it's not
currently a real problem, the pages and offsets arrays can be eliminated,
which saves approximately 1000 bytes of stack space.
Signed-off-by: Peter Osterlund <petero2@telia.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Unlocking the door when the disc is in use is obviously not good, because then
it's possible to eject the disc at the wrong time and cause severe disc data
corruption.
Signed-off-by: Peter Osterlund <petero2@telia.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
If opening for write fails, the open method should return -EROFS. This makes
"mount" try again with a read-only mount, instead of just giving up.
Signed-off-by: Peter Osterlund <petero2@telia.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Change some messages that don't indicate an error so that they are only
printed when debugging is enabled.
Signed-off-by: Peter Osterlund <petero2@telia.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
There's a bug in releasing scsi_device where the release function
actually frees the block queue. However, the block queue release
calls flush_work(), which requires process context (the scsi_device
structure may release from irq context). Update the release function
to invoke via the execute_in_process_context() API.
Also clean up the scsi_target structure releasing via this API.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
We have several points in the SCSI stack (primarily for our device
functions) where we need to guarantee process context, but (given the
place where the last reference was released) we cannot guarantee this.
This API gets around the issue by executing the function directly if
the caller has process context, but scheduling a workqueue to execute
in process context if the caller doesn't have it. Unfortunately, it
requires memory allocation in interrupt context, but it's better than
what we have previously. The true solution will require a bit of
re-engineering, so isn't appropriate for 2.6.16.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Probe and remove methods are now defined at bus level. No more need to
redefine them at driver level in i2c-isa.
This lets us get rid of these annoying messages:
Driver 'it87-isa' needs updating - please use bus_type methods
Thanks to Nicolas Mailhot for reporting the problem and testing the fix.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fix an oops on it87 module removal when no supported hardware was
found.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Use the real-time status registers of the Winbond W83782D, W83783S and
W83627HF chips, instead of the interrupt status registers. Interrupts
cannot be trusted at least for voltage inputs, as they are two-times
triggers (as opposed to comparator mode, which we want.) The w83627hf
driver was fixed in a similar way some times ago.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The VT8231 low temperature limits are actually hysteresis temperatures
to the high limits.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Roger Lucas <roger@planbit.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The following patch looks good to me. It adds an unusual_devs entry as
well as fixing an ordering bug. Please apply.
From: Bohdan Linda <bohdan.linda@gmail.com>
Signed-off-by: Phil Dibowitz <phil@ipom.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Here is a new entry for unusual_devs.h (as630).
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The switchover to "platform_driver" from "device_driver" missed
one rather essential usage, which broke the sl811_cs driver ...
this resolves the omission.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The patch adds the USB ID (0413:2101) for the Leadtek GPS-Mouse 9531 to
the driver pl2303.
Signed-off-by: Christian Lindner <christian.lindner@gmx.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Disable some dubious "early" USB handoff code that allegedly works around bugs
on some systems (we don't know which ones) but rudely breaks some others.
Also make the kernel warnings reporting BIOS handoff problems be more useful,
reporting the register whose value displays the trouble.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
drivers/net/appletalk/cops.c: In function `cops_load':
drivers/net/appletalk/cops.c:539: warning: assignment discards qualifiers from pointer target type
drivers/net/appletalk/cops.c:547: warning: assignment discards qualifiers from pointer target type
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
I get a machine check exception, triple fault, or NMI watchdog lockup
when DRI gets enabled on this card.
(And Mauro Tassinari <mtassinari@cmanet.it> reports hung kernels too in
http://lkml.org/lkml/2006/1/26/97)
[ Adrian Bunk also states that this is the only RV350 entry for an RV370
in our lists, which implies that it's just buggy ]
Cc: Adrian Bunk <bunk@stusta.de>
Cc: Dave Jones <davej@redhat.com>
Cc: Mauro Tassinari <mtassinari@cmanet.it>
Cc: Dave Airlie <airlied@linux.ie>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Before the PCMCIA subsystem was fully integrated into the device and
driver model, the BT3C driver had to workaround this when loading the
firmware. This workaround is broken and makes the driver oops when
loading the firmware. This patch removes this workaround and uses now
the provided device structure from the PCMCIA subsystem.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The orinoco wireless driver can support the SMC 2532W-B PC Card, so add the
id for it.
Signed-off-by: Jesse Allen <the3dfxdude@gmail.com>
Cc: Pavel Roskin <proski@gnu.org>
Cc: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The previous dev->max_sectors patch made sht->max_sectors meaningless.
Kill all initializations of sht->max_sectors.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
If a low level driver wants to control max_sectors, it had to adjust
ap->host->max_sectors and set ATA_DFLAG_LOCK_SECTORS to tell
ata_scsi_slave_config not to override the limit. This is not only
cumbersome but also incorrect for hosts which support more than one
devices per port.
This patch adds per-device ->max_sectors. If the field is unset
(zero), libata core layer will adjust ->max_sectors according to
default rules. If the field is set, libata honors the setting.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
cdb_len is per-device property. Sharing cdb_len on ap results in
inaccurate configuration on revalidation and hotplugging. This patch
makes cdb_len per-device.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
ata_dev_knobble() unconditionally used the first device of the port to
determine whether a device is bridged or not. This causes bridge
limit to be incorrectly applied or unapplied for hosts with slave
devices (e.g. ata_piix).
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
EDD is never used with ->probe_reset. Don't handle EDD special case
in ata_dev_identify if ->probe_reset is in use.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Make ata_dump_id() take @id instead of @dev. This is preparation for
splitting ata_dev_identify().
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Separate out ATA major version calculation from ata_dev_identify()
into ata_id_major_version(). It's preparation for splitting
ata_dev_identify().
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Separate out n_sectors calculation into ata_id_n_sectors() from
ata_dev_identify(). This will be used by revalidation.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
ata_dev_id_c_string() reads ATA string from the specified offset of
the given IDENTIFY PAGE and puts it in the specified buffer in trimmed
and NULL-terminated form. The caller must supply a buffer which is
one byte larger than the maximum size of the target ID string.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
In piix_sata_probe(), mask gets assigned unnecessarily at the
beginning of the function. Kill the assignment.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
This patch makes ata_bus_probe() normalize classes[] returned by
->probe_reset such that ->probe_reset can return ATA_DEV_UNKNOWN.
This eases implementation of ->probe_reset's which don't directly use
ata_drive_probe_reset().
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
pm->sg.size is set from the Residual Byte Count register. However,
the upper byte of the RBC is the opcode of the instruction that was
executing, so we need to mask it off. This fixes some spurious rejects
of IGNORE WIDE RESIDUE messages.
Signed-off-by: Matthew Wilcox <matthew@wil.cx>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Flush workqueue of a scsi host after a remote port for that host
is registered at the fc transport class. Otherwise immediate
registration of a scsi device on that host is racy.
Signed-off-by: Andreas Herrmann <aherrman@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Avoid access to old fsf_requests if device reset is logged.
Signed-off-by: Maxim Shchetynin <maxim@de.ibm.com>
Signed-off-by: Andreas Herrmann <aherrman@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Remove endless polling for replug of the local link. Just wait for
link up notification.
Signed-off-by: Andreas Herrmann <aherrman@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Remove all remainders of obsolete zfcp adapter attributes physical_wwpn and
physical_s_id.
Signed-off-by: Andreas Herrmann <aherrman@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Attached patch fixes problem that cause kobject_register failure
during loading. Kobject_register would fail when there are more than
1 module with same module name. This patch will change module name of
megaraid_legacy from 'megaraid' to 'megaraid_legacy'.
Signed-Off-by: Seokmann Ju <seokmann.ju@lsil.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Since scsi core is always sending scatterlists now, remove
some code which was written with the bad assumption that
a small transfer would not be sent down in a scatterlist.
Without this fix, the ipr driver ends up sending garbage
data to the adapter following a reset, causing it to
fail the reset and take the adapter offline.
Signed-off-by: Brian King <brking@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Rename get_support function to pcwd_check_temperature_support
so that it is clearer what the function does.
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
The following makes drivers/char/watchdog/sa1100_wdt.c sparse clean.
(similar to the other watchdog drivers)
Signed-off-by: Ian Campbell <icampbell@arcom.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
drivers/video/fbmem.c:1567: warning: 'video_setup' defined but not used
Acked-by: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The BUS_I2C option is neither available (since there is no VISWS option in
the kernel) nor does it have any effect - so why not remove it?
Based on a report by Jean-Luc Leger <reiga@dspnet.fr.eu.org>.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
- tipar_open(): fix unsigned comparison
- tipar_open(): don't permit NULL pardevice (probably unneeded given the
above fix).
- tipar_init_module(): handle the situation where parport_register_driver()
failed to register any devices (parport_register_driver() drops the ->attach
return value on the floor).
This probably makes fixes#1 and #2 unneeded.
- tipar_init_module(): fix various error-path resource leaks.
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
When the sclp interface takes very long to serve a request, the sclp core
driver will report a failed request to the sclp tty driver even though the
request is still being processed by the sclp interface. Eventually the sclp
interface completes the request and updates some fields in the request buffer
which leads to a corrupted tty pages list. The next time function
sclp_tty_write_room is called, the corrupted list will be traversed, resulting
in an oops.
To avoid this remove the busy retry limit and increase retry intervals.
Signed-off-by: Peter Oberparleiter <peter.oberparleiter@de.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix locking in __chp_add() and s390_subchannel_remove_chpid(): Need to
disable/enable because they are always called from a thread (and not
directly from a machine check...)
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch converts all assert(xxx)'s in low-level drivers to
WARN_ON(!xxx)'s. After this patch, there is no in-kernel user of the
libata assert() macro.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
In an effort to kill libata-specific assert() and use generic
WARN_ON(), this patch converts all assert(X)'s in libata core layer to
WARN_ON(!X)'s. Most conversions are straight-forward logical negation
exception for the followings.
* In libata-core.c:ata_fill_sg(),
assert(qc->n_elem > 0) is converted to WARN_ON(qc->n_elem == 0) because
qc->n_elem is unsigned and unsigned <= 0 is weird.
* In libata-scsi.c:ata_gen_ata_desc/fixed_sense(),
assert(NULL != qc->ap->ops->tf_read) is converted to
WARN_ON(qc->ap->ops->tf_read == NULL), as there are no other users of
'constant cond var' style in libata.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Make ahci_fill_cmd_slot() take struct ahci_port_priv *pp instead of
struct ata_port *ap as suggested by Jeff Garzik.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
This patch inlines ata_qc_complete() and uninlines __ata_qc_complete()
as suggested by Jeff Garzik.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Even after the last fix, it's still possible for a send-only join to
start before the join for the broadcast group has finished. This
could cause us to create a multicast group using attributes from the
broadcast group that haven't been initialized yet, so we would use
garbage for the Q_Key, etc. Fix this by waiting until the broadcast
group's attached flag is set before starting send-only joins.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
When debugging is enabled, the mthca_QUERY_DEV_LIM() firmware command
function prints out some of the device limits that it queries.
However the debugging prints happen before all of the fields are
extracted from the firmware response, so some of the values that get
printed are uninitialized junk. Move the prints to the end of the
function to fix this.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Serial drivers in general should not write uart_info->flags - they're
private to serial_core. Serial drivers have no need to fiddle with
tty->alt_speed, nor manipulate TTY_IO_ERROR in tty->flags. Fix the
ioc4 serial driver for both these points by simply removing the
offending code.
Acked-by: pfg@sgi.com
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch contains help text updates including the following:
- XFree86 * -> X
- there is no need for repeating part of the help text of the AGP
option and having "If unsure, say Y/N." in the chip specific
options.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Dave Jones <davej@redhat.com>
Prevent stalled processing of received data when a driver allocates tty
buffer space but does not immediately follow the allocation with more data
and a call to schedule receive tty processing. (example: hvc_console) This
bug was introduced by the first locking patch for the new tty buffering.
Signed-off-by: Paul Fulghum <paulkf@microgate.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Firmware should go into /lib/firmware, not /etc/firmware.
Found by Alejandro Bonilla.
Signed-off-by: Jesper Juhl <jesper.juhl@gmail.com>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Acked-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Now that libata is smart enough to handle both soft and hard resets,
add hardreset method. Note that sil24 hardreset doesn't supply
signature; still, the new reset mechanism can make good use of it.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Convert sata_sil to use new reset mechanism. sata_sil is fairly
generic and can directly use std routine.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Don't clear SError in sata_std_hardreset(). This makes hardreset act
identically to ->phy_reset register-wise.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
This patch makes std component operations act identical to ->phy_reset
register-wise except for SError clearing on sata_std_hardreset.
Note that if a driver only implements/uses hardreset, it should not
use ata_std_probeinit() to avoid extra sata_phy_resume() and
ata_busy_sleep() compared to ->phy_reset.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Separate out ahci_fill_cmd_slot() from ahci_qc_prep().
ahci_fill_cmd_slot() can later be used to issue non-standard commands.
(e.g. softreset)
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
->eng_timeout cannot be invoked with NULL qc anymore. Add an
assertion in ata_scsi_error() and kill NULL qc handling from all
->eng_timeout callbacks.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Implement ata_scsi_timed_out(), to be used as
scsi_host_template->eh_timed_out callback for all libata drivers.
Without this function, the following race exists.
If a qc completes after SCSI timer expires but before libata EH kicks
in, the qc gets completed but the scsicmd still gets passed to libata
EH resulting in ->eng_timeout invocation with NULL qc, which none is
handling properly.
This patch makes sure that scmd and qc share the same lifetime.
Original idea from Jeff Garzik <jgarzik@pobox.com>.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Add ATA_QCFLAG_EH_SCHEDULED. If this flag is set, the qc is owned by
EH and normal completion path is not allowed to finish it. This patch
doesn't actually use this flag.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
This patch implements the off-the-shelf probeinit component operation.
Currently, all it does is waking up the PHY if it's a SATA port.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
This patch adds probeinit component operation to
ata_drive_probe_reset(). If present, this new operation is called
before performing any reset. The operations's roll is to prepare @ap
for following probe-reset operations.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
This patch separates out sata_phy_resume() from sata_std_hardreset().
The function will later be used by probeinit callback.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
ap->cbl is initialized during postreset and thus unknown on entry to
ata_std_probe_reset(). This patch makes ata_std_probe_reset() use
ATA_FLAG_SATA flag instead of ap->cbl to detect SATA port.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
This patch makes sure that pio tasks are flushed before proceeding
with EH.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
ATA_FLAG_IN_EH flag is set on entry to EH and cleared on completion.
This patch just sets and clears the flag. Following patches will
build normal qc execution / EH synchronization aroung this flag.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Use seq_file interface for proc output in sba_iommu. Also
clean up the bus root assignment, and give the proc files
a more logical name. Tested on my J6000.
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
Gut ccio-dma.c of the ugly proc append and snprintf cruft and
just use seq_printf instead. Tested on a K-class.
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
This patch adds new PCI serial card support.
Signed-off-by: Yoichi Yuasa <yoichi_yuasa@tripeaks.co.jp>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This replaces old direct usage of tty->flip stuff with relative flip API
calls.
Signed-off-by: Vitaly Bordug <vbordug@ru.mvista.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The DB1550 actually doesn't have a UART2. Remove it from the list.
Signed-off-by: Jordan Crouse <jordan.crouse@amd.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
On some embedded PowerPC (MPC834x) systems an extra byte would some
times be required to flush data out of the fifo.
serial8250_console_write() was updating the IER in hardware without
also updating the copy in uart_8250_port. This causes issues functions
like serial8250_start_tx() and __stop_tx() to misbehave.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Lucas Correia Villa Real
This patch defines the number of serial ports on the S3C2400.
Signed-off-by: Lucas Correia Villa Real <lucasvr@gobolinux.org>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Quoth BenH:
"Ok, looks like I forgot to update the Kconfig for the new i2c driver,
it should select I2C_POWERMAC instead. Do you want a new patch or
can you just fix it there ?"
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch adds a windfarm module, windfarm_pm112, for the dual core G5s
(both 2 and 4 core models), keeping the machine from getting into
vacuum-cleaner mode ;) For proper credits, the patch was initially
written by Paul Mackerras, and slightly reworked by me to add overtemp
handling among others. The patch also removes the sysfs attributes from
windfarm_pm81 and windfarm_pm91 and instead adds code to the windfarm
core to automagically expose attributes for sensor & controls.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* compat_alloc_user_space() returns __user pointer
* copying between two userland areas is copy_in_user(), not copy_from_user()
* dereferencing userland pointers is bad
* so's get_user() from local variables
... plus usual __user annotations
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
MTD_XIP depends on having working asm/mtd-xip.h; it's not just per-architecture
(arm-only, as current Kconfig would have it), but actually per-subarch as
well. Introduced a new symbol (ARCH_MTD_XIP) set by arch Kconfig; MTD_XIP
depends on it.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
A bunch of asm/bug.h includes are both not needed (since it will get
pulled anyway) and bogus (since they are done too early). Removed.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Further, there's an additional issue that I saw in testing:
ipoib_mcast_send may get called when priv->broadcast is NULL (e.g. if
the device was downed and then upped internally because of a port
event).
If this happends and the send-only join request gets completed before
priv->broadcast is set, we get an oops.
Signed-off-by: Michael S. Tsirkin <mst@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Fix the following race scenario:
- Device is up.
- Port event or set mcast list triggers ipoib_mcast_stop_thread,
this cancels the query and waits on mcast "done" completion.
- Completion is called and "done" is set.
- Meanwhile, ipoib_mcast_send arrives and starts a new query,
re-initializing "done".
Fix this by adding a "multicast started" bit and checking it before
starting a send-only join.
Signed-off-by: Michael S. Tsirkin <mst@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Use the new tty_schedule_flip() instead of the original direct
schedule_work of the flip buffer.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Use the new tty_schedule_flip() instead of the original direct
schedule_work of the flip buffer.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Re-organize the default CONSOLE baud rate define setting so that
it is only set once.
Use the new tty_schedule_flip() instead of the original direct
schedule_work of the flip buffer.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This does not show up unless you #define DEBUG in the file, which most
people wouldn't do. On PPC405, at least, "sector_t" is unsigned long,
which doesn't match %llx/%llu. Since sector# may well be >32 bits, promote
the value to match the format.
Signed-off-by: Michael Richardson <mcr@xelerance.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
drivers/base/bus.c:166: warning: `driver_attr_unbind' defined but not used
drivers/base/bus.c:194: warning: `driver_attr_bind' defined but not used
Looks like these two attributes and supporting functions want to be
#ifdef HOTPLUG'd
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
4gb products require an IOCB's FCP-LUN to be formatted in
wire-format prior to submission.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Recent ISP24xx firmwares require that mailbox register 8 be
set to the maximum number of bytes to transfer during DMA
copying of the list. We safely set this value to zero
(infinite), since the call is *only* made in FCAL
topologies.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Commit 854165f424
inadvertently added some code meant only for testing -- the
driver was ignoring the non-zero function numbers of a
multi-port HBA.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Fcport visibility is recognized during interrupt time, but,
rport removal can only occur during a process
(sleeping)-context. Return a DID_IMM_RETRY status for
commands submitted within this window to insure I/Os do not
prematurely run-out of retries.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
The at76c651 and tda80xx frontends are currently completely unused, IOW
their only effect is making the kernel larger for people accitentially
enabling them.
The current in-kernel drivers differ from the drivers at cvs.tuxbox.org,
and re-adding them when parts of the dbox2 project get merged should be
trivial.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- When a firmware was downloaded dvb_usb_device_init returns NULL for the
dvb_usb_device, then nothing should be done with that pointer and device,
because it will re-enumerate.
- A new firmware should be used with digitv devices.
- It should make "slave"-devices work and others, too.
Signed-off-by: Patrick Boettcher <pb@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Reassigning function pointers in a static led to infinite loops when using
multiple VP7045-based device at the same time on one system. Using kmalloc'd
copies for reassignments is better.
Signed-off-by: Patrick Boettcher <pb@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Use the parallel transport function of the MT352 demodulator in
TH7579 and LGZ201 -based FusionHDTV Bluebird usb boxes.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Use the parallel transport function of the MT352 in USB demodulator of the
Dual Digital board.
Signed-off-by: Chris Pascoe <c.pascoe@itee.uq.edu.au>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
South Korea uses NTSC-M but with A2 audio instead of BTSC. Several audio
chips need this information in order to set the correct audio processing
registers.
Acked-by: Mauro Carvalho Chehab <mauro_chehab@yahoo.com.br>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
add IR support to KWorld DVB-T (cx22702-based)
Signed-off-by: Marco Manenti <marco_manenti@colman.it>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- added signal detection support to tvp5150
Signed-off-by: Markus Rechberger <mrechberger@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Apparently, having the number of lines fixed at 4 reduces (or even kills)
the buzz found in NICAM stereo with analog sound.
Signed-off-by: Marcin Rudowski <mar_rud@poczta.onet.pl>
Signed-off-by: Ricardo Cerqueira <v4l@cerqueira.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- rename DVB_USB_CXUSB one-liner description to:
Conexant USB2.0 hybrid reference design support.
- with the addition of bluebird support to dvb-usb-cxusb,
it now depends on lgdt330x and mt352 modules.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Make the whole netdevices menu depend on NET, rather than having an empty
submenu when networking is disabled.
Indeed, almost the whole body of the menu was surrounded by if NETDEVICES,
and what was outside depended on NETCONSOLE which is inside the menu.
Signed-off-by: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
drivers/net/tulip/uli526x.c: In function `__check_mode':
drivers/net/tulip/uli526x.c:1693: warning: return from incompatible pointer type
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Jeff Garzik
Joshua Kinard
Linus Torvalds
Dan Williams
Francois Romieu
Russell King
Andrew Morton
Christian Trefzer
Jes Sorensen
Herbert Poetzl
Ralf Baechle
Arthur Othieno
David Brownell
Dmitry Torokhov
Meelis Roos
Alessandro Zummo
Karsten Keil
Bjorn Helgaas
Paul Fulghum
Peter Osterlund
Alan Cox
James Bottomley
Jean Delvare
Phil Dibowitz
Alan Stern
David Brownell
Christian Lindner
Michael Hund
David S. Miller
Roland Dreier
Dave Jones
Marcel Holtmann
Jesse Allen
Tejun Heo
Matthew Wilcox
Andreas Herrmann
Maxim Shchetynin
Ju, Seokmann
Brian King
Wim Van Sebroeck
Ian Campbell
Antonino A. Daplas
Adrian Bunk
Peter Oberparleiter
Cornelia Huck
Jesper Juhl
Kyle McMartin
Jordan Crouse
Yoichi Yuasa
Vitaly Bordug
Kumar Gala
Lucas Correia Villa Real
Al Viro
Benjamin Herrenschmidt
Michael S. Tsirkin
Greg Ungerer
Michael Richardson
Russell King
Jens Axboe
andrew.vasquez@qlogic.com
Mauro Carvalho Chehab
Patrick Boettcher
Michael Krufky
Chris Pascoe
Oliver Endriss
Markus Rechberger
Hans Verkuil
Marco Manenti
Manu Abraham
Marcin Rudowski
Paolo 'Blaisorblade' Giarrusso