Commit Graph

1946 Commits

Author SHA1 Message Date
Linus Torvalds 477558d7e8 SCSI misc on 20190315
This is the final round of mostly small fixes and performance
 improvements to our initial submit.  The main regression fix is the
 ia64 simscsi build failure which was missed in the serial number
 elimination conversion.
 
 Signed-off-by: James E.J. Bottomley <jejb@linux.ibm.com>
 -----BEGIN PGP SIGNATURE-----
 
 iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCXIxBayYcamFtZXMuYm90
 dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pisherpAP4rxLpX
 bcUnQnEsvoxys/JyoK08Qfv1JebZo1B2MAZ62wD/VZ7LpOuzVLhsM2KhLFGRrs1/
 7D2K4tgtO2dQsFix7H0=
 =pcHl
 -----END PGP SIGNATURE-----

Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi

Pull more SCSI updates from James Bottomley:
 "This is the final round of mostly small fixes and performance
  improvements to our initial submit.

  The main regression fix is the ia64 simscsi build failure which was
  missed in the serial number elimination conversion"

* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (24 commits)
  scsi: ia64: simscsi: use request tag instead of serial_number
  scsi: aacraid: Fix performance issue on logical drives
  scsi: lpfc: Fix error codes in lpfc_sli4_pci_mem_setup()
  scsi: libiscsi: Hold back_lock when calling iscsi_complete_task
  scsi: hisi_sas: Change SERDES_CFG init value to increase reliability of HiLink
  scsi: hisi_sas: Send HARD RESET to clear the previous affiliation of STP target port
  scsi: hisi_sas: Set PHY linkrate when disconnected
  scsi: hisi_sas: print PHY RX errors count for later revision of v3 hw
  scsi: hisi_sas: Fix a timeout race of driver internal and SMP IO
  scsi: hisi_sas: Change return variable type in phy_up_v3_hw()
  scsi: qla2xxx: check for kstrtol() failure
  scsi: lpfc: fix 32-bit format string warning
  scsi: lpfc: fix unused variable warning
  scsi: target: tcmu: Switch to bitmap_zalloc()
  scsi: libiscsi: fall back to sendmsg for slab pages
  scsi: qla2xxx: avoid printf format warning
  scsi: lpfc: resolve static checker warning in lpfc_sli4_hba_unset
  scsi: lpfc: Correct __lpfc_sli_issue_iocb_s4 lockdep check
  scsi: ufs: hisi: fix ufs_hba_variant_ops passing
  scsi: qla2xxx: Fix panic in qla_dfs_tgt_counters_show
  ...
2019-03-16 12:51:50 -07:00
Linus Torvalds 92fff53b71 SCSI misc on 20190306
This is mostly update of the usual drivers: arcmsr, qla2xxx, lpfc,
 hisi_sas, target/iscsi and target/core.  Additionally Christoph
 refactored gdth as part of the dma changes.  The major mid-layer
 change this time is the removal of bidi commands and with them the
 whole of the osd/exofs driver and filesystem.
 
 Signed-off-by: James E.J. Bottomley <jejb@linux.ibm.com>
 -----BEGIN PGP SIGNATURE-----
 
 iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCXIC54SYcamFtZXMuYm90
 dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pishT1GAPwJEV23
 ExPiPsnuVgKj49nLTagZ3rILRQcYNbL+MNYqxQEA0cT8FHzSDBfWY5OKPNE+RQ8z
 f69LpXGmMpuagKGvvd4=
 =Fhy1
 -----END PGP SIGNATURE-----

Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi

Pull SCSI updates from James Bottomley:
 "This is mostly update of the usual drivers: arcmsr, qla2xxx, lpfc,
  hisi_sas, target/iscsi and target/core.

  Additionally Christoph refactored gdth as part of the dma changes. The
  major mid-layer change this time is the removal of bidi commands and
  with them the whole of the osd/exofs driver and filesystem. This is a
  major simplification for block and mq in particular"

* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (240 commits)
  scsi: cxgb4i: validate tcp sequence number only if chip version <= T5
  scsi: cxgb4i: get pf number from lldi->pf
  scsi: core: replace GFP_ATOMIC with GFP_KERNEL in scsi_scan.c
  scsi: mpt3sas: Add missing breaks in switch statements
  scsi: aacraid: Fix missing break in switch statement
  scsi: kill command serial number
  scsi: csiostor: drop serial_number usage
  scsi: mvumi: use request tag instead of serial_number
  scsi: dpt_i2o: remove serial number usage
  scsi: st: osst: Remove negative constant left-shifts
  scsi: ufs-bsg: Allow reading descriptors
  scsi: ufs: Allow reading descriptor via raw upiu
  scsi: ufs-bsg: Change the calling convention for write descriptor
  scsi: ufs: Remove unused device quirks
  Revert "scsi: ufs: disable vccq if it's not needed by UFS device"
  scsi: megaraid_sas: Remove a bunch of set but not used variables
  scsi: clean obsolete return values of eh_timed_out
  scsi: sd: Optimal I/O size should be a multiple of physical block size
  scsi: MAINTAINERS: SCSI initiator and target tweaks
  scsi: fcoe: make use of fip_mode enum complete
  ...
2019-03-09 16:53:47 -08:00
Andy Shevchenko 98effe4746 scsi: target: tcmu: Switch to bitmap_zalloc()
Switch to bitmap_zalloc() to show clearly what we are allocating.  Besides
that it returns pointer of bitmap type instead of opaque void *.

Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Acked-by: Mike Christie <mchristi@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2019-03-06 19:26:46 -05:00
Cathy Avery 2ff717cdc6 scsi: target: tcmu: wait for nl reply only if there are listeners or during an add
genlmsg_multicast_allns now returns the correct statuses when a message is
sent to a listener. However in the case of adding a device we want to wait
for the listener otherwise we may miss the the device during startup.

Signed-off-by: Cathy Avery <cavery@redhat.com>
Acked-by: Mike Christie <mchristi@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2019-03-06 19:26:13 -05:00
Christoph Hellwig ae3d56d815 scsi: remove bidirectional command support
No real need for bidi support once the OSD code is gone.

Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2019-02-05 21:29:21 -05:00
David Disseldorp b6cd7f34ba scsi: target: make the pi_prot_format ConfigFS path readable
pi_prot_format conversion to write-only caused userspace breakage. Make the
ConfigFS path readable again and hardcode the "0\n" content, matching
previous output.

Fixes: 6baca7601b ("scsi: target: drop unused pi_prot_format attribute storage")
Link: https://bugzilla.redhat.com/show_bug.cgi?id=1667505
Reported-by: Lee Duncan <lduncan@suse.com>
Reported-by: Laura Abbott <labbott@redhat.com>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: David Disseldorp <ddiss@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2019-02-04 21:40:32 -05:00
Bart Van Assche 47eefded1f scsi: target/iscsi: Simplify iscsit_handle_text_cmd()
Treat text_in and padding as a single buffer instead of two buffers.

Cc: Nicholas Bellinger <nab@linux-iscsi.org>
Cc: Mike Christie <mchristi@redhat.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Hannes Reinecke <hare@suse.de>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2019-02-04 21:37:50 -05:00
Bart Van Assche 658c31224d scsi: target/iscsi: Simplify iscsit_dump_data_payload()
Use a single loop to dump immediate data, padding and digest instead of
using separate rx_data() calls for each type of data.

Cc: Nicholas Bellinger <nab@linux-iscsi.org>
Cc: Mike Christie <mchristi@redhat.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Hannes Reinecke <hare@suse.de>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2019-02-04 21:36:54 -05:00
Bart Van Assche 32e36bfbcf scsi: target/iscsi: Avoid iscsit_release_commands_from_conn() deadlock
When using SCSI passthrough in combination with the iSCSI target driver
then cmd->t_state_lock may be obtained from interrupt context. Hence, all
code that obtains cmd->t_state_lock from thread context must disable
interrupts first. This patch avoids that lockdep reports the following:

WARNING: inconsistent lock state
4.18.0-dbg+ #1 Not tainted
--------------------------------
inconsistent {HARDIRQ-ON-W} -> {IN-HARDIRQ-W} usage.
iscsi_ttx/1800 [HC1[1]:SC0[2]:HE0:SE0] takes:
000000006e7b0ceb (&(&cmd->t_state_lock)->rlock){?...}, at: target_complete_cmd+0x47/0x2c0 [target_core_mod]
{HARDIRQ-ON-W} state was registered at:
 lock_acquire+0xd2/0x260
 _raw_spin_lock+0x32/0x50
 iscsit_close_connection+0x97e/0x1020 [iscsi_target_mod]
 iscsit_take_action_for_connection_exit+0x108/0x200 [iscsi_target_mod]
 iscsi_target_rx_thread+0x180/0x190 [iscsi_target_mod]
 kthread+0x1cf/0x1f0
 ret_from_fork+0x24/0x30
irq event stamp: 1281
hardirqs last  enabled at (1279): [<ffffffff970ade79>] __local_bh_enable_ip+0xa9/0x160
hardirqs last disabled at (1281): [<ffffffff97a008a5>] interrupt_entry+0xb5/0xd0
softirqs last  enabled at (1278): [<ffffffff977cd9a1>] lock_sock_nested+0x51/0xc0
softirqs last disabled at (1280): [<ffffffffc07a6e04>] ip6_finish_output2+0x124/0xe40 [ipv6]

other info that might help us debug this:
Possible unsafe locking scenario:

      CPU0
      ----
 lock(&(&cmd->t_state_lock)->rlock);
 <Interrupt>
   lock(&(&cmd->t_state_lock)->rlock);

*** DEADLOCK ***

3 locks held by iscsi_ttx/1800:
*0: 00000000c3b711b7 (sk_lock-AF_INET6){+.+.}, at: tcp_sendmsg+0x1e/0x50
*1: 00000000fa81046f (rcu_read_lock){....}, at: inet6_csk_xmit+0xc7/0x2e0 [ipv6]
*2: 00000000c091d70d (rcu_read_lock_bh){....}, at: ip6_finish_output2+0x124/0xe40 [ipv6]

stack backtrace:
CPU: 0 PID: 1800 Comm: iscsi_ttx Not tainted 4.18.0-dbg+ #1
Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 1.0.0-prebuilt.qemu-project.org 04/01/2014
Call Trace:
<IRQ>
dump_stack+0xa4/0xf5
print_usage_bug+0x25b/0x27b
mark_lock+0x70f/0x7b0
__lock_acquire+0xbc2/0x1b50
lock_acquire+0xd2/0x260
_raw_spin_lock_irqsave+0x4a/0x60
target_complete_cmd+0x47/0x2c0 [target_core_mod]
target_complete_cmd_with_length+0x70/0xa0 [target_core_mod]
pscsi_req_done+0x335/0x530 [target_core_pscsi]
__blk_mq_end_request+0xa5/0x140
scsi_end_request+0x112/0x320 [scsi_mod]
scsi_io_completion+0x183/0xa30 [scsi_mod]
scsi_finish_command+0x1c0/0x280 [scsi_mod]
scsi_softirq_done+0x19a/0x230 [scsi_mod]
__blk_mq_complete_request_remote+0x2f/0x40
flush_smp_call_function_queue+0x12a/0x220
generic_smp_call_function_single_interrupt+0x13/0x30
smp_call_function_single_interrupt+0x7a/0x350
call_function_single_interrupt+0xf/0x20
</IRQ>
RIP: 0010:__asan_load4+0x1e/0x80
debug_lockdep_rcu_enabled+0x26/0x40
ip6_finish_output2+0x15a/0xe40 [ipv6]
ip6_finish_output+0x308/0x440 [ipv6]
ip6_output+0x11d/0x3b0 [ipv6]
ip6_xmit+0x639/0xc50 [ipv6]
inet6_csk_xmit+0x198/0x2e0 [ipv6]
__tcp_transmit_skb+0xc1b/0x15b0
tcp_write_xmit+0x42e/0x1f20
__tcp_push_pending_frames+0x59/0x150
tcp_push+0x189/0x270
tcp_sendmsg_locked+0x7b9/0x1680
tcp_sendmsg+0x2c/0x50
inet_sendmsg+0x71/0x250
sock_sendmsg+0x4c/0x60
tx_data+0x12b/0x1f0 [iscsi_target_mod]
iscsit_send_tx_data+0x77/0xe0 [iscsi_target_mod]
iscsit_xmit_pdu+0x2c5/0x740 [iscsi_target_mod]
iscsit_response_queue+0x941/0xd40 [iscsi_target_mod]
iscsi_target_tx_thread+0x23b/0x350 [iscsi_target_mod]
kthread+0x1cf/0x1f0
ret_from_fork+0x24/0x30

Fixes: 064cdd2d91 ("target: Fix race between iscsi-target connection shutdown + ABORT_TASK")
Cc: Nicholas Bellinger <nab@linux-iscsi.org>
Cc: Mike Christie <mchristi@redhat.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Hannes Reinecke <hare@suse.de>
Cc: <stable@vger.kernel.org>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2019-02-04 21:35:44 -05:00
Bart Van Assche 1e65cc1631 scsi: target/iscsi: Rename a function and a function pointer
Having both a function and a function pointer member with the same
name (iscsit_release_cmd) is confusing. Hence rename the function pointer
member.

Cc: Nicholas Bellinger <nab@linux-iscsi.org>
Cc: Mike Christie <mchristi@redhat.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Hannes Reinecke <hare@suse.de>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2019-02-04 21:34:49 -05:00
Bart Van Assche 0300b1147e scsi: target/iscsi: Fix spelling of "unsolicited"
Change "unsoliticed" into "unsolicited".

Cc: Nicholas Bellinger <nab@linux-iscsi.org>
Cc: Mike Christie <mchristi@redhat.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Hannes Reinecke <hare@suse.de>
Cc: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2019-02-04 21:33:59 -05:00
Bart Van Assche 618baaf788 scsi: target/iscsi: Convert comments about locking into runtime checks
Cc: Nicholas Bellinger <nab@linux-iscsi.org>
Cc: Mike Christie <mchristi@redhat.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Hannes Reinecke <hare@suse.de>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2019-02-04 21:33:08 -05:00
Bart Van Assche b53655b80c scsi: target/iscsi: Remove an incorrect comment
The single iscsit_start_nopin_response_timer() caller does not hold any
locks. Hence remove the comment above this function.

Cc: Nicholas Bellinger <nab@linux-iscsi.org>
Cc: Mike Christie <mchristi@redhat.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Hannes Reinecke <hare@suse.de>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2019-02-04 21:32:38 -05:00
Bart Van Assche 94ebb47160 scsi: target/core: Add target_send_busy()
Introduce a function that sends the SCSI status "BUSY" back to the
initiator. The next patch will add a call to this function in the srpt
target driver.

Reviewed-by: Hannes Reinecke <hare@suse.com>
Cc: Nicholas Bellinger <nab@linux-iscsi.org>
Cc: Mike Christie <mchristi@redhat.com>
Cc: Christoph Hellwig <hch@lst.de>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2019-02-04 21:28:48 -05:00
Bart Van Assche 83f85b8ec3 scsi: target/core: Inline transport_lun_remove_cmd()
Remove the code that clears .se_lun from transport_cmd_check_stop_to_fabric()
such that the transport_lun_remove_cmd() call can be moved into
target_release_cmd_kref(). Because this guarantees that
transport_lun_remove_cmd() will be called exactly once, it is safe to change
the cmpxchg() call into a test of se_cmd.lun_ref_active. Inline
transport_lun_remove_cmd() because it is not worth to keep it as a separate
function.

Reviewed-by: Hannes Reinecke <hare@suse.com>
Cc: Nicholas Bellinger <nab@linux-iscsi.org>
Cc: Mike Christie <mchristi@redhat.com>
Cc: Christoph Hellwig <hch@lst.de>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2019-02-04 21:27:20 -05:00
Bart Van Assche 2281c95fe7 scsi: target/core: Simplify the LUN RESET implementation
Due to the task management handling rework it is safe to wait for a TMF
that is not in the active state. Hence remove the CMD_T_ACTIVE test from
core_tmr_drain_tmr_list(). Additionally, call __target_check_io_state()
instead of open coding it.

Reviewed-by: Hannes Reinecke <hare@suse.com>
Cc: Nicholas Bellinger <nab@linux-iscsi.org>
Cc: Mike Christie <mchristi@redhat.com>
Cc: Christoph Hellwig <hch@lst.de>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2019-02-04 21:26:24 -05:00
Bart Van Assche 3f0661a492 scsi: target/core: Remove several state tests from the TMF code
Whether or not a session is being torn down does not affect whether or not
SCSI commands are in the task set. Hence remove the "tearing down" checks
from the TMF code. The TRANSPORT_ISTATE_PROCESSING check is left out
because it is now safe to wait for a command that is in that state. The
CMD_T_PRE_EXECUTE is left out because abort processing is postponed until
after commands have left the pre-execute state since the patch that makes
TMF processing synchronous.

See also commit 1c21a48055 ("target: Avoid early CMD_T_PRE_EXECUTE
failures during ABORT_TASK").

Cc: Nicholas Bellinger <nab@linux-iscsi.org>
Cc: Mike Christie <mchristi@redhat.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Hannes Reinecke <hare@suse.de>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2019-02-04 21:25:13 -05:00
Bart Van Assche f80d2f0846 scsi: target/core: Remove the write_pending_status() callback function
Due to the patch that makes TMF handling synchronous the
write_pending_status() callback function is no longer called.  Hence remove
it.

Acked-by: Felipe Balbi <balbi@ti.com>
Reviewed-by: Sagi Grimberg <sagig@mellanox.com>
Reviewed-by: Andy Grover <agrover@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Bryant G. Ly <bryantly@linux.vnet.ibm.com>
Cc: Nicholas Bellinger <nab@linux-iscsi.org>
Cc: Mike Christie <mchristi@redhat.com>
Cc: Himanshu Madhani <himanshu.madhani@qlogic.com>
Cc: Quinn Tran <quinn.tran@qlogic.com>
Cc: Saurav Kashyap <saurav.kashyap@qlogic.com>
Cc: Michael S. Tsirkin <mst@redhat.com>
Cc: Juergen Gross <jgross@suse.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2019-02-04 21:23:59 -05:00
Xiubo Li 40d883b091 scsi: tcmu: fix use after free
Fixes: a94a2572b9 ("scsi: tcmu: avoid cmd/qfull timers updated whenever a new cmd comes")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Cc: Mike Christie <mchristi@redhat.com>
Signed-off-by: Xiubo Li <xiubli@redhat.com>
Reviewed-by: Mike Christie <mchristi@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2019-01-22 20:54:00 -05:00
Xiubo Li a94a2572b9 scsi: tcmu: avoid cmd/qfull timers updated whenever a new cmd comes
Currently there is one cmd timeout timer and one qfull timer for each udev,
and whenever any new command is coming in we will update the cmd timer or
qfull timer. For some corner cases the timers are always working only for
the ringbuffer's and full queue's newest cmd. That's to say the timer won't
be fired even if one cmd has been stuck for a very long time and the
deadline is reached.

This fix will keep the cmd/qfull timers to be pended for the oldest cmd in
ringbuffer and full queue, and will update them with the next cmd's
deadline only when the old cmd's deadline is reached or removed from the
ringbuffer and full queue.

Signed-off-by: Xiubo Li <xiubli@redhat.com>
Acked-by: Mike Christie <mchristi@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2019-01-11 20:58:52 -05:00
Leo Zhang 621a4367d6 scsi: target/iscsi: fix error msg typo when create lio_qr_cache failed
Signed-off-by: Leo Zhang <nguzcf@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2019-01-08 21:57:25 -05:00
Linus Torvalds 938edb8a31 SCSI misc on 20181224
This is mostly update of the usual drivers: smarpqi, lpfc, qedi,
 megaraid_sas, libsas, zfcp, mpt3sas, hisi_sas.  Additionally, we have
 a pile of annotation, unused variable and minor updates.  The big API
 change is the updates for Christoph's DMA rework which include
 removing the DISABLE_CLUSTERING flag.  And finally there are a couple
 of target tree updates.
 
 Signed-off-by: James E.J. Bottomley <jejb@linux.ibm.com>
 -----BEGIN PGP SIGNATURE-----
 
 iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCXCEUNiYcamFtZXMuYm90
 dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pishdjKAP9vrTTv
 qFaYmAoRSbPq9ZiixaXLMy0K/6o76Uay0gnBqgD/fgn3jg/KQ6alNaCjmfeV3wAj
 u1j3H7tha9j1it+4pUw=
 =GDa+
 -----END PGP SIGNATURE-----

Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi

Pull SCSI updates from James Bottomley:
 "This is mostly update of the usual drivers: smarpqi, lpfc, qedi,
  megaraid_sas, libsas, zfcp, mpt3sas, hisi_sas.

  Additionally, we have a pile of annotation, unused variable and minor
  updates.

  The big API change is the updates for Christoph's DMA rework which
  include removing the DISABLE_CLUSTERING flag.

  And finally there are a couple of target tree updates"

* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (259 commits)
  scsi: isci: request: mark expected switch fall-through
  scsi: isci: remote_node_context: mark expected switch fall-throughs
  scsi: isci: remote_device: Mark expected switch fall-throughs
  scsi: isci: phy: Mark expected switch fall-through
  scsi: iscsi: Capture iscsi debug messages using tracepoints
  scsi: myrb: Mark expected switch fall-throughs
  scsi: megaraid: fix out-of-bound array accesses
  scsi: mpt3sas: mpt3sas_scsih: Mark expected switch fall-through
  scsi: fcoe: remove set but not used variable 'port'
  scsi: smartpqi: call pqi_free_interrupts() in pqi_shutdown()
  scsi: smartpqi: fix build warnings
  scsi: smartpqi: update driver version
  scsi: smartpqi: add ofa support
  scsi: smartpqi: increase fw status register read timeout
  scsi: smartpqi: bump driver version
  scsi: smartpqi: add smp_utils support
  scsi: smartpqi: correct lun reset issues
  scsi: smartpqi: correct volume status
  scsi: smartpqi: do not offline disks for transient did no connect conditions
  scsi: smartpqi: allow for larger raid maps
  ...
2018-12-28 14:48:06 -08:00
Linus Torvalds 0e9da3fbf7 for-4.21/block-20181221
-----BEGIN PGP SIGNATURE-----
 
 iQJEBAABCAAuFiEEwPw5LcreJtl1+l5K99NY+ylx4KYFAlwb7R8QHGF4Ym9lQGtl
 cm5lbC5kawAKCRD301j7KXHgpjiID/97oDjMhNT7rwpuMbHw855h62j1hEN/m+N3
 FI0uxivYoYZLD+eJRnMcBwHlKjrCX8iJQAcv9ffI3ThtFW7dnZT3atUacaZVR/Dt
 IrxdymdBP3qsmuaId5NYBug7rJ+AiqFJKjEvCcSPu5X397J4I3SEbzhfvYLJ/aZX
 16o0HJlVVIrcbmq1IP4HwiIIOaKXvPaw04L4z4fpeynRSWG7EAi8NLSnhlR4Rxbb
 BTiMkCTsjRCFdyO6da4fvNQKWmPGPa3bJkYy3qR99cvJCeIbQjRyCloQlWNJRRgi
 3eJpCHVxqFmN0/+DNTJVQEEr4H8o0AVucrLVct1Jc4pessenkpoUniP8vELqwlng
 Z2VHLkhTfCEmvFlk82grrYdNvGATRsrbswt/PlP4T7rBfr1IpDk8kXDWF59EL2dy
 ly35Sk3wJGHBl8qa+vEPXOAnaWdqJXuVGpwB4ifOIatOls8mOxwfZjiRc7x05/fC
 1O4rR2IfLwRqwoYHs0AJ+h6ohOSn1mkGezl2Tch1VSFcJUOHmuYvraTaUi6hblpA
 SslaAoEhO39hRBL0HsvsMeqVWM9uzqvFkLDCfNPdiA81H1258CIbo4vF8z6czCIS
 eeXnTJxVhPVbZgb3a1a93SPwM6KIDZFoIijyd+NqjpU94thlnhYD0QEcKJIKH7os
 2p4aHs6ktw==
 =TRdW
 -----END PGP SIGNATURE-----

Merge tag 'for-4.21/block-20181221' of git://git.kernel.dk/linux-block

Pull block updates from Jens Axboe:
 "This is the main pull request for block/storage for 4.21.

  Larger than usual, it was a busy round with lots of goodies queued up.
  Most notable is the removal of the old IO stack, which has been a long
  time coming. No new features for a while, everything coming in this
  week has all been fixes for things that were previously merged.

  This contains:

   - Use atomic counters instead of semaphores for mtip32xx (Arnd)

   - Cleanup of the mtip32xx request setup (Christoph)

   - Fix for circular locking dependency in loop (Jan, Tetsuo)

   - bcache (Coly, Guoju, Shenghui)
      * Optimizations for writeback caching
      * Various fixes and improvements

   - nvme (Chaitanya, Christoph, Sagi, Jay, me, Keith)
      * host and target support for NVMe over TCP
      * Error log page support
      * Support for separate read/write/poll queues
      * Much improved polling
      * discard OOM fallback
      * Tracepoint improvements

   - lightnvm (Hans, Hua, Igor, Matias, Javier)
      * Igor added packed metadata to pblk. Now drives without metadata
        per LBA can be used as well.
      * Fix from Geert on uninitialized value on chunk metadata reads.
      * Fixes from Hans and Javier to pblk recovery and write path.
      * Fix from Hua Su to fix a race condition in the pblk recovery
        code.
      * Scan optimization added to pblk recovery from Zhoujie.
      * Small geometry cleanup from me.

   - Conversion of the last few drivers that used the legacy path to
     blk-mq (me)

   - Removal of legacy IO path in SCSI (me, Christoph)

   - Removal of legacy IO stack and schedulers (me)

   - Support for much better polling, now without interrupts at all.
     blk-mq adds support for multiple queue maps, which enables us to
     have a map per type. This in turn enables nvme to have separate
     completion queues for polling, which can then be interrupt-less.
     Also means we're ready for async polled IO, which is hopefully
     coming in the next release.

   - Killing of (now) unused block exports (Christoph)

   - Unification of the blk-rq-qos and blk-wbt wait handling (Josef)

   - Support for zoned testing with null_blk (Masato)

   - sx8 conversion to per-host tag sets (Christoph)

   - IO priority improvements (Damien)

   - mq-deadline zoned fix (Damien)

   - Ref count blkcg series (Dennis)

   - Lots of blk-mq improvements and speedups (me)

   - sbitmap scalability improvements (me)

   - Make core inflight IO accounting per-cpu (Mikulas)

   - Export timeout setting in sysfs (Weiping)

   - Cleanup the direct issue path (Jianchao)

   - Export blk-wbt internals in block debugfs for easier debugging
     (Ming)

   - Lots of other fixes and improvements"

* tag 'for-4.21/block-20181221' of git://git.kernel.dk/linux-block: (364 commits)
  kyber: use sbitmap add_wait_queue/list_del wait helpers
  sbitmap: add helpers for add/del wait queue handling
  block: save irq state in blkg_lookup_create()
  dm: don't reuse bio for flushes
  nvme-pci: trace SQ status on completions
  nvme-rdma: implement polling queue map
  nvme-fabrics: allow user to pass in nr_poll_queues
  nvme-fabrics: allow nvmf_connect_io_queue to poll
  nvme-core: optionally poll sync commands
  block: make request_to_qc_t public
  nvme-tcp: fix spelling mistake "attepmpt" -> "attempt"
  nvme-tcp: fix endianess annotations
  nvmet-tcp: fix endianess annotations
  nvme-pci: refactor nvme_poll_irqdisable to make sparse happy
  nvme-pci: only set nr_maps to 2 if poll queues are supported
  nvmet: use a macro for default error location
  nvmet: fix comparison of a u16 with -1
  blk-mq: enable IO poll if .nr_queues of type poll > 0
  blk-mq: change blk_mq_queue_busy() to blk_mq_queue_inflight()
  blk-mq: skip zero-queue maps in blk_mq_map_swqueue
  ...
2018-12-28 13:19:59 -08:00
Linus Torvalds e0c38a4d1f Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next
Pull networking updates from David Miller:

 1) New ipset extensions for matching on destination MAC addresses, from
    Stefano Brivio.

 2) Add ipv4 ttl and tos, plus ipv6 flow label and hop limit offloads to
    nfp driver. From Stefano Brivio.

 3) Implement GRO for plain UDP sockets, from Paolo Abeni.

 4) Lots of work from Michał Mirosław to eliminate the VLAN_TAG_PRESENT
    bit so that we could support the entire vlan_tci value.

 5) Rework the IPSEC policy lookups to better optimize more usecases,
    from Florian Westphal.

 6) Infrastructure changes eliminating direct manipulation of SKB lists
    wherever possible, and to always use the appropriate SKB list
    helpers. This work is still ongoing...

 7) Lots of PHY driver and state machine improvements and
    simplifications, from Heiner Kallweit.

 8) Various TSO deferral refinements, from Eric Dumazet.

 9) Add ntuple filter support to aquantia driver, from Dmitry Bogdanov.

10) Batch dropping of XDP packets in tuntap, from Jason Wang.

11) Lots of cleanups and improvements to the r8169 driver from Heiner
    Kallweit, including support for ->xmit_more. This driver has been
    getting some much needed love since he started working on it.

12) Lots of new forwarding selftests from Petr Machata.

13) Enable VXLAN learning in mlxsw driver, from Ido Schimmel.

14) Packed ring support for virtio, from Tiwei Bie.

15) Add new Aquantia AQtion USB driver, from Dmitry Bezrukov.

16) Add XDP support to dpaa2-eth driver, from Ioana Ciocoi Radulescu.

17) Implement coalescing on TCP backlog queue, from Eric Dumazet.

18) Implement carrier change in tun driver, from Nicolas Dichtel.

19) Support msg_zerocopy in UDP, from Willem de Bruijn.

20) Significantly improve garbage collection of neighbor objects when
    the table has many PERMANENT entries, from David Ahern.

21) Remove egdev usage from nfp and mlx5, and remove the facility
    completely from the tree as it no longer has any users. From Oz
    Shlomo and others.

22) Add a NETDEV_PRE_CHANGEADDR so that drivers can veto the change and
    therefore abort the operation before the commit phase (which is the
    NETDEV_CHANGEADDR event). From Petr Machata.

23) Add indirect call wrappers to avoid retpoline overhead, and use them
    in the GRO code paths. From Paolo Abeni.

24) Add support for netlink FDB get operations, from Roopa Prabhu.

25) Support bloom filter in mlxsw driver, from Nir Dotan.

26) Add SKB extension infrastructure. This consolidates the handling of
    the auxiliary SKB data used by IPSEC and bridge netfilter, and is
    designed to support the needs to MPTCP which could be integrated in
    the future.

27) Lots of XDP TX optimizations in mlx5 from Tariq Toukan.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1845 commits)
  net: dccp: fix kernel crash on module load
  drivers/net: appletalk/cops: remove redundant if statement and mask
  bnx2x: Fix NULL pointer dereference in bnx2x_del_all_vlans() on some hw
  net/net_namespace: Check the return value of register_pernet_subsys()
  net/netlink_compat: Fix a missing check of nla_parse_nested
  ieee802154: lowpan_header_create check must check daddr
  net/mlx4_core: drop useless LIST_HEAD
  mlxsw: spectrum: drop useless LIST_HEAD
  net/mlx5e: drop useless LIST_HEAD
  iptunnel: Set tun_flags in the iptunnel_metadata_reply from src
  net/mlx5e: fix semicolon.cocci warnings
  staging: octeon: fix build failure with XFRM enabled
  net: Revert recent Spectre-v1 patches.
  can: af_can: Fix Spectre v1 vulnerability
  packet: validate address length if non-zero
  nfc: af_nfc: Fix Spectre v1 vulnerability
  phonet: af_phonet: Fix Spectre v1 vulnerability
  net: core: Fix Spectre v1 vulnerability
  net: minor cleanup in skb_ext_add()
  net: drop the unused helper skb_ext_get()
  ...
2018-12-27 13:04:52 -08:00
Christoph Hellwig 4af14d113b scsi: remove the use_clustering flag
The same effects can be achieved by setting the dma_boundary to
PAGE_SIZE - 1 and the max_segment_size to PAGE_SIZE, so shift those
settings into the drivers.  Note that in many cases the setting might
be bogus, but this keeps the status quo.

[mkp: fix myrs and myrb]

Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2018-12-18 23:19:21 -05:00
Wei Yongjun 8b2db98e81 scsi: target/core: Use kmem_cache_free() instead of kfree()
memory allocated by kmem_cache_alloc() should be freed using
kmem_cache_free(), not kfree().

Fixes: ad669505c4 ("scsi: target/core: Make sure that target_wait_for_sess_cmds() waits long enough")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2018-12-18 22:52:14 -05:00
Varun Prakash 9e6371d3c6 scsi: target: iscsi: cxgbit: add missing spin_lock_init()
Add missing spin_lock_init() for cdev->np_lock.

Signed-off-by: Varun Prakash <varun@chelsio.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2018-12-12 19:49:35 -05:00
Varun Prakash ed076c55b3 scsi: target: iscsi: cxgbit: fix csk leak
In case of arp failure call cxgbit_put_csk() to free csk.

Signed-off-by: Varun Prakash <varun@chelsio.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2018-12-12 19:49:17 -05:00
David Disseldorp 3beeabd5f2 scsi: target: perform t10_wwn ID initialisation in target_alloc_device()
Initialise the t10_wwn vendor, model and revision defaults when a device is
allocated instead of when it's enabled. This ensures that custom vendor or
model strings set prior to enablement are not later overwritten with
default values.

The TRANSPORT_FLAG_PASSTHROUGH conditional can be dropped for the following
reasons:

 - target_core_pscsi overwrites the defaults in the
   pscsi_configure_device() callback.
   + the contents is then only used for ConfigFS via
     $pscsi_dev/statistics/scsi_lu/vend, etc.

 - target_core_user doesn't touch the defaults, nor are they used for
   anything outside of ConfigFS.

Signed-off-by: David Disseldorp <ddiss@suse.de>
Reviewed-by: Roman Bolshakov <r.bolshakov@yadro.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2018-12-07 21:54:33 -05:00
David Disseldorp 2d88284728 scsi: target: remove hardcoded T10 Vendor ID in INQUIRY response
Use the value stored in t10_wwn.vendor, which defaults to "LIO-ORG", but
can be reconfigured via the vendor_id ConfigFS attribute.

Signed-off-by: David Disseldorp <ddiss@suse.de>
Reviewed-by: Bryant G. Ly <bly@catalogicsoftware.com>
Reviewed-by: Lee Duncan <lduncan@suse.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Roman Bolshakov <r.bolshakov@yadro.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2018-12-07 21:54:33 -05:00
David Disseldorp 54a6f3f6a4 scsi: target: add device vendor_id configfs attribute
The vendor_id attribute will allow for the modification of the T10 Vendor
Identification string returned in inquiry responses. Its value can be
viewed and modified via the ConfigFS path at:

target/core/$backstore/$name/wwn/vendor_id

"LIO-ORG" remains the default value, which is set when the backstore device
is enabled.

[mkp: corrected VPD page number]

Signed-off-by: David Disseldorp <ddiss@suse.de>
Reviewed-by: Roman Bolshakov <r.bolshakov@yadro.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2018-12-07 21:54:33 -05:00
David Disseldorp b2da4abf26 scsi: target: consistently null-terminate t10_wwn strings
In preparation for supporting user provided vendor strings, add an extra
byte to the vendor, model and revision arrays in struct t10_wwn. This
ensures that the full INQUIRY data can be carried in the arrays along with
a null-terminator.

Change a number of array readers and writers so that they account for
explicit null-termination:

- The pscsi_set_inquiry_info() and emulate_model_alias_store() codepaths
  don't currently explicitly null-terminate; fix this.

- Existing t10_wwn field dumps use for-loops which step over
  null-terminators for right-padding.
  + Use printf with width specifiers instead.

Signed-off-by: David Disseldorp <ddiss@suse.de>
Reviewed-by: Roman Bolshakov <r.bolshakov@yadro.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2018-12-07 21:54:33 -05:00
David Disseldorp 0de263577d scsi: target: use consistent left-aligned ASCII INQUIRY data
spc5r17.pdf specifies:

  4.3.1 ASCII data field requirements
  ASCII data fields shall contain only ASCII printable characters (i.e.,
  code values 20h to 7Eh) and may be terminated with one or more ASCII null
  (00h) characters.  ASCII data fields described as being left-aligned
  shall have any unused bytes at the end of the field (i.e., highest
  offset) and the unused bytes shall be filled with ASCII space characters
  (20h).

LIO currently space-pads the T10 VENDOR IDENTIFICATION and PRODUCT
IDENTIFICATION fields in the standard INQUIRY data. However, the PRODUCT
REVISION LEVEL field in the standard INQUIRY data as well as the T10 VENDOR
IDENTIFICATION field in the INQUIRY Device Identification VPD Page are
zero-terminated/zero-padded.

Fix this inconsistency by using space-padding for all of the above fields.

Signed-off-by: David Disseldorp <ddiss@suse.de>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Bryant G. Ly <bly@catalogicsoftware.com>
Reviewed-by: Lee Duncan <lduncan@suse.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Roman Bolshakov <r.bolshakov@yadro.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2018-12-07 21:54:33 -05:00
Bart Van Assche 3ad9800231 scsi: target/core: Reduce the amount of code executed with a spinlock held
Due to the "make ABORT and LUN RESET handling synchronous" patch, cmd->work
is only modified from the regular command execution path and no longer
asynchronously by the code that executes task management functions. Since
the regular command execution code is sequential per command, no locking is
required to manipulate cmd->work. Hence stop protecting cmd->work
manipulations with locking.

Cc: Nicholas Bellinger <nab@linux-iscsi.org>
Cc: Mike Christie <mchristi@redhat.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: David Disseldorp <ddiss@suse.de>
Cc: Hannes Reinecke <hare@suse.de>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2018-12-07 21:22:55 -05:00
Bart Van Assche 2c9fa49e10 scsi: target/core: Make ABORT and LUN RESET handling synchronous
Instead of invoking target driver callback functions from the context that
handles an abort or LUN RESET task management function, only set the abort
flag from that context and perform the actual abort handling from the
context of the regular command processing flow. This approach has the
advantage that the task management code becomes much easier to read and to
verify since the number of potential race conditions against the command
processing flow is strongly reduced.

This patch has been tested by running the following two shell commands
concurrently for about ten minutes for both the iSCSI and the SRP target
drivers ($dev is an initiator device node connected with storage provided
by the target driver under test):

 * fio with data verification enabled on a filesystem mounted on top of
   $dev.

 * while true; do sg_reset -d $dev; echo -n .; sleep .1; done

Cc: Nicholas Bellinger <nab@linux-iscsi.org>
Cc: Mike Christie <mchristi@redhat.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: David Disseldorp <ddiss@suse.de>
Cc: Hannes Reinecke <hare@suse.de>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2018-12-07 21:22:55 -05:00
Bart Van Assche aaa00cc93c scsi: target/core: Fix TAS handling for aborted commands
The TASK ABORTED STATUS (TAS) bit is defined as follows in SAM:
"TASK_ABORTED: this status shall be returned if a command is aborted by a
command or task management function on another I_T nexus and the control
mode page TAS bit is set to one". TAS handling is spread over the target
core and the iSCSI target driver. If a LUN RESET is received, the target
core will send the TASK_ABORTED response for all commands for which such a
response has to be sent. If an ABORT TASK is received, only the iSCSI
target driver will send the TASK_ABORTED response for the commands for
which that response has to be sent.  That is a bug since all target drivers
have to honor the TAS bit. Fix this by moving the code that handles TAS
from the iSCSI target driver into the target core. Additionally, if a
command has been aborted, instead of sending the TASK_ABORTED status from
the context that processes the SCSI command send it from the context of the
ABORT TMF.  The core_tmr_abort_task() change in this patch causes the
CMD_T_TAS flag to be set if a TASK_ABORTED status has to be sent back to
the initiator that submitted the command. If that flag has been set
transport_cmd_finish_abort() will send the TASK_ABORTED response.

Cc: Nicholas Bellinger <nab@linux-iscsi.org>
Cc: Mike Christie <mchristi@redhat.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: David Disseldorp <ddiss@suse.de>
Cc: Hannes Reinecke <hare@suse.de>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2018-12-07 21:22:15 -05:00
Bart Van Assche fbbd492355 scsi: target/core: Simplify the code for aborting SCSI commands
Instead of allowing the code that aborts a SCSI command to finish before
all iSCSI data frames have been received, make that code wait until all
iSCSI data frames have been received. Introduce a new member variable in
the target driver template to communicate that information from the iSCSI
target driver to the target core. This change allows to leave out the check
whether or not it is already safe to send the TASK_ABORTED reply from
transport_send_task_abort().

Cc: Nicholas Bellinger <nab@linux-iscsi.org>
Cc: Mike Christie <mchristi@redhat.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: David Disseldorp <ddiss@suse.de>
Cc: Hannes Reinecke <hare@suse.de>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2018-12-07 21:20:07 -05:00
Bart Van Assche a014c3647a scsi: target/core: Make it possible to wait from more than one context for command completion
This patch does not change any functionality but makes the patch that makes
TMF handling synchronous easier to read.

Cc: Nicholas Bellinger <nab@linux-iscsi.org>
Cc: Mike Christie <mchristi@redhat.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: David Disseldorp <ddiss@suse.de>
Cc: Hannes Reinecke <hare@suse.de>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2018-12-07 21:20:07 -05:00
Bart Van Assche db5b21a24e scsi: target/core: Use system workqueues for TMF
A quote from SAM-5: "The order in which task management requests are
processed is not specified by the SCSI architecture model.  The SCSI
architecture model does not require in-order delivery of such task
management requests or processing by the task manager in the order
received. To guarantee the processing order of task management requests
referencing sent to a specific logical unit, an application client should
not have more than one such task management request pending to that logical
unit." This means that it is safe to use the system workqueues instead of
tmr_wq for processing TMFs. An intended side effect of this patch is that
it enables concurrent processing of TMFs.

Reviewed-by: Christoph Hellwig <hch@lst.de>
Cc: Nicholas Bellinger <nab@linux-iscsi.org>
Cc: Mike Christie <mchristi@redhat.com>
Cc: David Disseldorp <ddiss@suse.de>
Cc: Hannes Reinecke <hare@suse.de>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2018-12-07 21:20:07 -05:00
Bart Van Assche ad669505c4 scsi: target/core: Make sure that target_wait_for_sess_cmds() waits long enough
A session must only be released after all code that accesses the session
structure has finished. Make sure that this is the case by introducing a
new command counter per session that is only decremented after the
.release_cmd() callback has finished. This patch fixes the following crash:

BUG: KASAN: use-after-free in do_raw_spin_lock+0x1c/0x130
Read of size 4 at addr ffff8801534b16e4 by task rmdir/14805
CPU: 16 PID: 14805 Comm: rmdir Not tainted 4.18.0-rc2-dbg+ #5
Call Trace:
dump_stack+0xa4/0xf5
print_address_description+0x6f/0x270
kasan_report+0x241/0x360
__asan_load4+0x78/0x80
do_raw_spin_lock+0x1c/0x130
_raw_spin_lock_irqsave+0x52/0x60
srpt_set_ch_state+0x27/0x70 [ib_srpt]
srpt_disconnect_ch+0x1b/0xc0 [ib_srpt]
srpt_close_session+0xa8/0x260 [ib_srpt]
target_shutdown_sessions+0x170/0x180 [target_core_mod]
core_tpg_del_initiator_node_acl+0xf3/0x200 [target_core_mod]
target_fabric_nacl_base_release+0x25/0x30 [target_core_mod]
config_item_release+0x9c/0x110 [configfs]
config_item_put+0x26/0x30 [configfs]
configfs_rmdir+0x3b8/0x510 [configfs]
vfs_rmdir+0xb3/0x1e0
do_rmdir+0x262/0x2c0
do_syscall_64+0x77/0x230
entry_SYSCALL_64_after_hwframe+0x49/0xbe

Cc: Nicholas Bellinger <nab@linux-iscsi.org>
Cc: Mike Christie <mchristi@redhat.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: David Disseldorp <ddiss@suse.de>
Cc: Hannes Reinecke <hare@suse.de>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2018-12-07 21:20:07 -05:00
Bart Van Assche a95be3842c scsi: target/core: Simplify transport_clear_lun_ref()
Since transport_clear_lun_ref() already waits until the percpu-refcount
.release() method is called, it is not necessary to wait first until
percpu_ref_kill_and_confirm() has finished transitioning the refcount into
atomic mode. Remove the code that waits for percpu_ref_kill_and_confirm()
to complete and also the completion object that is used by that code.  This
patch does not change the behavior of the SCSI target code.

Cc: Nicholas Bellinger <nab@linux-iscsi.org>
Cc: Mike Christie <mchristi@redhat.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: David Disseldorp <ddiss@suse.de>
Cc: Hannes Reinecke <hare@suse.de>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2018-12-07 21:20:07 -05:00
Bart Van Assche 5d6cd9fe31 scsi: target/core: Use kvcalloc() instead of open-coding it
This patch does not change any functionality. Note: the code that frees
sess_cmd_map already uses kvfree() so that code does not need to be
modified.

Reviewed-by: David Disseldorp <ddiss@suse.de>
Cc: Nicholas Bellinger <nab@linux-iscsi.org>
Cc: Mike Christie <mchristi@redhat.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Hannes Reinecke <hare@suse.de>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2018-12-07 21:20:07 -05:00
Bart Van Assche e7f411049f scsi: target/tcmu: Fix queue_cmd_ring() declaration
This patch does not change any functionality but avoids that sparse
complains about the queue_cmd_ring() function and its callers.

Fixes: 6fd0ce7972 ("tcmu: prep queue_cmd_ring to be used by unmap wq")
Reviewed-by: David Disseldorp <ddiss@suse.de>
Cc: Nicholas Bellinger <nab@linux-iscsi.org>
Cc: Mike Christie <mchristi@redhat.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Hannes Reinecke <hare@suse.de>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2018-12-07 21:20:07 -05:00
Jens Axboe 5d2ee7122c sbitmap: optimize wakeup check
Even if we have no waiters on any of the sbitmap_queue wait states, we
still have to loop every entry to check. We do this for every IO, so
the cost adds up.

Shift a bit of the cost to the slow path, when we actually have waiters.
Wrap prepare_to_wait_exclusive() and finish_wait(), so we can maintain
an internal count of how many are currently active. Then we can simply
check this count in sbq_wake_ptr() and not have to loop if we don't
have any sleepers.

Convert the two users of sbitmap with waiting, blk-mq-tag and iSCSI.

Reviewed-by: Omar Sandoval <osandov@fb.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
2018-11-30 14:48:04 -07:00
David Disseldorp 59a206b449 scsi: target: replace fabric_ops.name with fabric_alias
iscsi_target_mod is the only LIO fabric where fabric_ops.name differs from
the fabric_ops.fabric_name string.  fabric_ops.name is used when matching
target/$fabric ConfigFS create paths, so rename it .fabric_alias and
fallback to target/$fabric vs .fabric_name comparison if .fabric_alias
isn't initialised.  iscsi_target_mod is the only fabric module to set
.fabric_alias . All other fabric modules rely on .fabric_name matching and
can drop the duplicate string.

Signed-off-by: David Disseldorp <ddiss@suse.de>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2018-11-28 18:50:59 -05:00
David Disseldorp 30c7ca9350 scsi: target: drop unnecessary get_fabric_name() accessor from fabric_ops
All fabrics return a const string. In all cases *except* iSCSI the
get_fabric_name() string matches fabric_ops.name.

Both fabric_ops.get_fabric_name() and fabric_ops.name are user-facing, with
the former being used for PR/ALUA state and the latter for ConfigFS
(config/target/$name), so we unfortunately need to keep both strings around
for now.  Replace the useless .get_fabric_name() accessor function with a
const string fabric_name member variable.

Signed-off-by: David Disseldorp <ddiss@suse.de>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2018-11-28 18:50:58 -05:00
David Disseldorp 6baca7601b scsi: target: drop unused pi_prot_format attribute storage
On write, the pi_prot_format configfs attribute invokes the device
format_prot() callback if present. Read dumps the contents of
se_dev_attrib.pi_prot_format which is always zero.  Make the configfs
attribute write-only, and drop the always zero se_dev_attrib.pi_prot_format
storage.

Signed-off-by: David Disseldorp <ddiss@suse.de>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2018-11-28 18:50:53 -05:00
Santosh Rastapur 02d805dc5f cxgb4: use new fw interface to get the VIN and smt index
If the fw supports returning VIN/VIVLD in FW_VI_CMD save it
in port_info structure else retrieve these from viid and save
them  in port_info structure. Do the same for smt_idx from
FW_VI_MAC_CMD

Signed-off-by: Santosh Rastapur <santosh@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2018-11-23 11:11:15 -08:00
David Disseldorp b49d6f7885 scsi: target: add emulate_pr backstore attr to toggle PR support
The new emulate_pr backstore attribute allows for Persistent Reservation
and SCSI2 RESERVE/RELEASE support to be completely disabled. This can be
useful for scenarios such as:

- Ensuring ATS (Compare & Write) usage on recent VMware ESXi initiators.

- Allowing clustered (e.g. tcm-user) backends to block such requests,
  avoiding the multi-node reservation state propagation.

When explicitly disabled, PR and RESERVE/RELEASE requests receive Invalid
Command Operation Code response sense data.

Signed-off-by: David Disseldorp <ddiss@suse.de>
Reviewed-by: Mike Christie <mchristi@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2018-11-21 22:10:36 -05:00
Jens Axboe a78b03bc73 Linux 4.20-rc3
-----BEGIN PGP SIGNATURE-----
 
 iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAlvx2sAeHHRvcnZhbGRz
 QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiGycgIAIuxobwt0RRKa0zO
 ROS+34JGoC2yU2P9VdEGWdtxS6ANMVQgKPBhWL6s+xR89Kd+V4xSdJLD1pNTxxqP
 0DCva0np1/Q4juH+JbU50v/lykoLgteZ0P0LBRGf1y8p3WiLPv45IbnNsMDNYhB2
 7a8rOmZYakRY9CPznRDw3X8cJt3sddKgFJHIOGz1OQJVWtCD0KPGcJmQNsbDSagY
 Zx6Z5BKSIdjRqaAdN5gDa1Pft3WQo7TpaQGl80lSsgr5LcjmscXA3sClOCy+25Mo
 FZLx0PcwP+Efq8RTGzNK51WSOMa6d37hvjDqUAdQBOR0KbyjRyXQwyQVw/MGbPJs
 7J3Pzm0=
 =56Mt
 -----END PGP SIGNATURE-----

Merge tag 'v4.20-rc3' into for-4.21/block

Merge in -rc3 to resolve a few conflicts, but also to get a few
important fixes that have gone into mainline since the block
4.21 branch was forked off (most notably the SCSI queue issue,
which is both a conflict AND needed fix).

Signed-off-by: Jens Axboe <axboe@kernel.dk>
2018-11-18 15:46:03 -07:00