get_cpl requires vcpu_load, so we must cache the result (whether the
vcpu was preempted when its cpl=0) in kvm_vcpu_arch.
Signed-off-by: Longpeng(Mike) <longpeng2@huawei.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
If a vcpu exits due to request a user mode spinlock, then
the spinlock-holder may be preempted in user mode or kernel mode.
(Note that not all architectures trap spin loops in user mode,
only AMD x86 and ARM/ARM64 currently do).
But if a vcpu exits in kernel mode, then the holder must be
preempted in kernel mode, so we should choose a vcpu in kernel mode
as a more likely candidate for the lock holder.
This introduces kvm_arch_vcpu_in_kernel() to decide whether the
vcpu is in kernel-mode when it's preempted. kvm_vcpu_on_spin's
new argument says the same of the spinning VCPU.
Signed-off-by: Longpeng(Mike) <longpeng2@huawei.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
It has been experimentally confirmed that supporting these two MSRs is one
of the necessary conditions for nested Hyper-V to use the TSC page. Modern
Windows guests are noticeably slower when they fall back to reading
timestamps from the HV_X64_MSR_TIME_REF_COUNT MSR instead of using the TSC
page.
The newly supported MSRs are advertised with the AccessFrequencyRegs
partition privilege flag and CPUID.40000003H:EDX[8] "Support for
determining timer frequencies is available" (both outside of the scope of
this KVM patch).
Reviewed-by: Radim Krčmář <rkrcmar@redhat.com>
Signed-off-by: Ladi Prosek <lprosek@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
If the SynIC timer message delivery fails due to SINT message slot being
busy, there's no point to attempt starting the timer again until we're
notified of the slot being released by the guest (via EOM or EOI).
Even worse, when a oneshot timer fails to deliver its message, its
re-arming with an expiration time in the past leads to immediate retry
of the delivery, and so on, without ever letting the guest vcpu to run
and release the slot, which results in a livelock.
To avoid that, only start the timer when there's no timer message
pending delivery. When there is, meaning the slot is busy, the
processing will be restarted upon notification from the guest that the
slot is released.
Signed-off-by: Roman Kagan <rkagan@virtuozzo.com>
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
Hyper-V identifies vCPUs by Virtual Processor Index, which can be
queried via HV_X64_MSR_VP_INDEX msr. It is defined by the spec as a
sequential number which can't exceed the maximum number of vCPUs per VM.
APIC ids can be sparse and thus aren't a valid replacement for VP
indices.
Current KVM uses its internal vcpu index as VP_INDEX. However, to make
it predictable and persistent across VM migrations, the userspace has to
control the value of VP_INDEX.
This patch achieves that, by storing vp_index explicitly on vcpu, and
allowing HV_X64_MSR_VP_INDEX to be set from the host side. For
compatibility it's initialized to KVM vcpu index. Also a few variables
are renamed to make clear distinction betweed this Hyper-V vp_index and
KVM vcpu_id (== APIC id). Besides, a new capability,
KVM_CAP_HYPERV_VP_INDEX, is added to allow the userspace to skip
attempting msr writes where unsupported, to avoid spamming error logs.
Signed-off-by: Roman Kagan <rkagan@virtuozzo.com>
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
There is a flaw in the Hyper-V SynIC implementation in KVM: when message
page or event flags page is enabled by setting the corresponding msr,
KVM zeroes it out. This is problematic because on migration the
corresponding MSRs are loaded on the destination, so the content of
those pages is lost.
This went unnoticed so far because the only user of those pages was
in-KVM hyperv synic timers, which could continue working despite that
zeroing.
Newer QEMU uses those pages for Hyper-V VMBus implementation, and
zeroing them breaks the migration.
Besides, in newer QEMU the content of those pages is fully managed by
QEMU, so zeroing them is undesirable even when writing the MSRs from the
guest side.
To support this new scheme, introduce a new capability,
KVM_CAP_HYPERV_SYNIC2, which, when enabled, makes sure that the synic
pages aren't zeroed out in KVM.
Signed-off-by: Roman Kagan <rkagan@virtuozzo.com>
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
Introduce a trivial, mostly empty <linux/sched/cputime.h> header
to prepare for the moving of cputime functionality out of sched.h.
Update all code that relies on these facilities.
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
200 commits and noteworthy changes for most architectures.
* ARM:
- GICv3 save/restore
- cache flushing fixes
- working MSI injection for GICv3 ITS
- physical timer emulation
* MIPS:
- various improvements under the hood
- support for SMP guests
- a large rewrite of MMU emulation. KVM MIPS can now use MMU notifiers
to support copy-on-write, KSM, idle page tracking, swapping, ballooning
and everything else. KVM_CAP_READONLY_MEM is also supported, so that
writes to some memory regions can be treated as MMIO. The new MMU also
paves the way for hardware virtualization support.
* PPC:
- support for POWER9 using the radix-tree MMU for host and guest
- resizable hashed page table
- bugfixes.
* s390: expose more features to the guest
- more SIMD extensions
- instruction execution protection
- ESOP2
* x86:
- improved hashing in the MMU
- faster PageLRU tracking for Intel CPUs without EPT A/D bits
- some refactoring of nested VMX entry/exit code, preparing for live
migration support of nested hypervisors
- expose yet another AVX512 CPUID bit
- host-to-guest PTP support
- refactoring of interrupt injection, with some optimizations thrown in
and some duct tape removed.
- remove lazy FPU handling
- optimizations of user-mode exits
- optimizations of vcpu_is_preempted() for KVM guests
* generic:
- alternative signaling mechanism that doesn't pound on tsk->sighand->siglock
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iQEcBAABAgAGBQJYral1AAoJEL/70l94x66DbNgH/Rx8YXuidFq2fe3RWOvld3RK
85OM/D5g38cTLpBE0/sJpcvX34iYN8U/l5foCZwpxB+83GHEk2Cr57JyfTogdaAJ
x8dBhHKQCA/HxSQUQLN6nFqRV+yT8WUR92Fhqx82+80BSen5Yzcfee/TDoW6T1IW
g8CYgX9FrRaGOX066ImAuUfdAdUVjyssfs9VttDTX+HiusPeuBPx/wsRe1ZEEPlH
vnltIJQb1ETV2GOZLUojKjzH6aZkjIl29XxjkYii9JTUornClG0DfW+5QT3uLrB5
gJ+G+Zmpsq8ZBx9jNDtAi7sFsoPY1Mzf+JPNCGXBra2sP2GrBAuXcxmgznRYltQ=
=8IIp
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull KVM updates from Paolo Bonzini:
"4.11 is going to be a relatively large release for KVM, with a little
over 200 commits and noteworthy changes for most architectures.
ARM:
- GICv3 save/restore
- cache flushing fixes
- working MSI injection for GICv3 ITS
- physical timer emulation
MIPS:
- various improvements under the hood
- support for SMP guests
- a large rewrite of MMU emulation. KVM MIPS can now use MMU
notifiers to support copy-on-write, KSM, idle page tracking,
swapping, ballooning and everything else. KVM_CAP_READONLY_MEM is
also supported, so that writes to some memory regions can be
treated as MMIO. The new MMU also paves the way for hardware
virtualization support.
PPC:
- support for POWER9 using the radix-tree MMU for host and guest
- resizable hashed page table
- bugfixes.
s390:
- expose more features to the guest
- more SIMD extensions
- instruction execution protection
- ESOP2
x86:
- improved hashing in the MMU
- faster PageLRU tracking for Intel CPUs without EPT A/D bits
- some refactoring of nested VMX entry/exit code, preparing for live
migration support of nested hypervisors
- expose yet another AVX512 CPUID bit
- host-to-guest PTP support
- refactoring of interrupt injection, with some optimizations thrown
in and some duct tape removed.
- remove lazy FPU handling
- optimizations of user-mode exits
- optimizations of vcpu_is_preempted() for KVM guests
generic:
- alternative signaling mechanism that doesn't pound on
tsk->sighand->siglock"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (195 commits)
x86/kvm: Provide optimized version of vcpu_is_preempted() for x86-64
x86/paravirt: Change vcp_is_preempted() arg type to long
KVM: VMX: use correct vmcs_read/write for guest segment selector/base
x86/kvm/vmx: Defer TR reload after VM exit
x86/asm/64: Drop __cacheline_aligned from struct x86_hw_tss
x86/kvm/vmx: Simplify segment_base()
x86/kvm/vmx: Get rid of segment_base() on 64-bit kernels
x86/kvm/vmx: Don't fetch the TSS base from the GDT
x86/asm: Define the kernel TSS limit in a macro
kvm: fix page struct leak in handle_vmon
KVM: PPC: Book3S HV: Disable HPT resizing on POWER9 for now
KVM: Return an error code only as a constant in kvm_get_dirty_log()
KVM: Return an error code only as a constant in kvm_get_dirty_log_protect()
KVM: Return directly after a failed copy_from_user() in kvm_vm_compat_ioctl()
KVM: x86: remove code for lazy FPU handling
KVM: race-free exit from KVM_RUN without POSIX signals
KVM: PPC: Book3S HV: Turn "KVM guest htab" message into a debug message
KVM: PPC: Book3S PR: Ratelimit copy data failure error messages
KVM: Support vCPU-based gfn->hva cache
KVM: use separate generations for each address space
...
Now that most cputime readers use the transition API which return the
task cputime in old style cputime_t, we can safely store the cputime in
nsecs. This will eventually make cputime statistics less opaque and more
granular. Back and forth convertions between cputime_t and nsecs in order
to deal with cputime_t random granularity won't be needed anymore.
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Rik van Riel <riel@redhat.com>
Cc: Stanislaw Gruszka <sgruszka@redhat.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Wanpeng Li <wanpeng.li@hotmail.com>
Link: http://lkml.kernel.org/r/1485832191-26889-8-git-send-email-fweisbec@gmail.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Interrupt to self can be sent without knowing the APIC ID.
Reviewed-by: David Hildenbrand <david@redhat.com>
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Introduce a new mutex to avoid an AB-BA deadlock between kvm->lock and
vcpu->mutex. Protect accesses in kvm_hv_setup_tsc_page too, as suggested
by Roman.
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Reviewed-by: Roman Kagan <rkagan@virtuozzo.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
synic_set_irq is only used in hyperv.c, and should be static to
avoid compiling warning when with -Wmissing-prototypes option.
Signed-off-by: Jiang Biao <jiang.biao2@zte.com.cn>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Lately tsc page was implemented but filled with empty
values. This patch setup tsc page scale and offset based
on vcpu tsc, tsc_khz and HV_X64_MSR_TIME_REF_COUNT value.
The valid tsc page drops HV_X64_MSR_TIME_REF_COUNT msr
reads count to zero which potentially improves performance.
Signed-off-by: Andrey Smetanin <asmetanin@virtuozzo.com>
Reviewed-by: Peter Hornyack <peterhornyack@google.com>
Reviewed-by: Radim Krčmář <rkrcmar@redhat.com>
CC: Paolo Bonzini <pbonzini@redhat.com>
CC: Roman Kagan <rkagan@virtuozzo.com>
CC: Denis V. Lunev <den@openvz.org>
[Computation of TSC page parameters rewritten to use the Linux timekeeper
parameters. - Paolo]
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Introduce a function that reads the exact nanoseconds value that is
provided to the guest in kvmclock. This crystallizes the notion of
kvmclock as a thin veneer over a stable TSC, that the guest will
(hopefully) convert with NTP. In other words, kvmclock is *not* a
paravirtualized host-to-guest NTP.
Drop the get_kernel_ns() function, that was used both to get the base
value of the master clock and to get the current value of kvmclock.
The former use is replaced by ktime_get_boot_ns(), the latter is
the purpose of get_kernel_ns().
This also allows KVM to provide a Hyper-V time reference counter that
is synchronized with the time that is computed from the TSC page.
Reviewed-by: Roman Kagan <rkagan@virtuozzo.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
If SynIC is disabled, there is nothing that userspace can do to
handle these exits; on the other hand, userspace probably will
not know about KVM_EXIT_HYPERV_HCALL and complain about it or
even exit. Just prevent anything bad from happening by handling
the hypercall in KVM and returning an "invalid hypercall" code.
Fixes: 83326e43f2
Cc: Andrey Smetanin <irqlevel@gmail.com>
Reviewed-by: Roman Kagan <rkagan@virtuozzo.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Currently we do not support Hyper-V hypercall continuation
so reject it.
Signed-off-by: Andrey Smetanin <asmetanin@virtuozzo.com>
Reviewed-by: Roman Kagan <rkagan@virtuozzo.com>
CC: Gleb Natapov <gleb@kernel.org>
CC: Paolo Bonzini <pbonzini@redhat.com>
CC: Joerg Roedel <joro@8bytes.org>
CC: "K. Y. Srinivasan" <kys@microsoft.com>
CC: Haiyang Zhang <haiyangz@microsoft.com>
CC: Roman Kagan <rkagan@virtuozzo.com>
CC: Denis V. Lunev <den@openvz.org>
CC: qemu-devel@nongnu.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Pass the return code from kvm_emulate_hypercall on to the caller,
in order to allow it to indicate to the userspace that
the hypercall has to be handled there.
Also adjust all the existing code paths to return 1 to make sure the
hypercall isn't passed to the userspace without setting kvm_run
appropriately.
Signed-off-by: Andrey Smetanin <asmetanin@virtuozzo.com>
Reviewed-by: Roman Kagan <rkagan@virtuozzo.com>
CC: Gleb Natapov <gleb@kernel.org>
CC: Paolo Bonzini <pbonzini@redhat.com>
CC: Joerg Roedel <joro@8bytes.org>
CC: "K. Y. Srinivasan" <kys@microsoft.com>
CC: Haiyang Zhang <haiyangz@microsoft.com>
CC: Roman Kagan <rkagan@virtuozzo.com>
CC: Denis V. Lunev <den@openvz.org>
CC: qemu-devel@nongnu.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Rename HV_X64_HV_NOTIFY_LONG_SPIN_WAIT by HVCALL_NOTIFY_LONG_SPIN_WAIT,
so the name is more consistent with the other hypercalls.
Signed-off-by: Andrey Smetanin <asmetanin@virtuozzo.com>
Reviewed-by: Roman Kagan <rkagan@virtuozzo.com>
CC: Gleb Natapov <gleb@kernel.org>
CC: Paolo Bonzini <pbonzini@redhat.com>
CC: Joerg Roedel <joro@8bytes.org>
CC: "K. Y. Srinivasan" <kys@microsoft.com>
CC: Haiyang Zhang <haiyangz@microsoft.com>
CC: Roman Kagan <rkagan@virtuozzo.com>
CC: Denis V. Lunev <den@openvz.org>
CC: qemu-devel@nongnu.org
[Change name, Andrey used HV_X64_HCALL_NOTIFY_LONG_SPIN_WAIT. - Paolo]
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Trace the following Hyper SynIC events:
* set msr
* set sint irq
* ack sint
* sint irq eoi
Signed-off-by: Andrey Smetanin <asmetanin@virtuozzo.com>
CC: Gleb Natapov <gleb@kernel.org>
CC: Paolo Bonzini <pbonzini@redhat.com>
CC: Roman Kagan <rkagan@virtuozzo.com>
CC: Denis V. Lunev <den@openvz.org>
CC: qemu-devel@nongnu.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Consolidate updating the Hyper-V SynIC timers in a
single place: on guest entry in processing KVM_REQ_HV_STIMER
request. This simplifies the overall logic, and makes sure
the most current state of msrs and guest clock is used for
arming the timers (to achieve that, KVM_REQ_HV_STIMER
has to be processed after KVM_REQ_CLOCK_UPDATE).
Signed-off-by: Andrey Smetanin <asmetanin@virtuozzo.com>
Reviewed-by: Roman Kagan <rkagan@virtuozzo.com>
CC: Gleb Natapov <gleb@kernel.org>
CC: Paolo Bonzini <pbonzini@redhat.com>
CC: Roman Kagan <rkagan@virtuozzo.com>
CC: Denis V. Lunev <den@openvz.org>
CC: qemu-devel@nongnu.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
QEMU zero-inits Hyper-V SynIC vectors. We should allow that,
and don't reject zero values if set by the host.
Signed-off-by: Andrey Smetanin <asmetanin@virtuozzo.com>
Reviewed-by: Roman Kagan <rkagan@virtuozzo.com>
CC: Gleb Natapov <gleb@kernel.org>
CC: Paolo Bonzini <pbonzini@redhat.com>
CC: Roman Kagan <rkagan@virtuozzo.com>
CC: Denis V. Lunev <den@openvz.org>
CC: qemu-devel@nongnu.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Hypervisor Function Specification(HFS) doesn't require
to disable SynIC timer at timer config write if timer->count = 0.
So drop this check, this allow to load timers MSR's
during migration restore, because config are set before count
in QEMU side.
Also fix condition according to HFS doc(15.3.1):
"It is not permitted to set the SINTx field to zero for an
enabled timer. If attempted, the timer will be
marked disabled (that is, bit 0 cleared) immediately."
Signed-off-by: Andrey Smetanin <asmetanin@virtuozzo.com>
Reviewed-by: Roman Kagan <rkagan@virtuozzo.com>
CC: Gleb Natapov <gleb@kernel.org>
CC: Paolo Bonzini <pbonzini@redhat.com>
CC: Roman Kagan <rkagan@virtuozzo.com>
CC: Denis V. Lunev <den@openvz.org>
CC: qemu-devel@nongnu.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Split stimer_expiration() into two parts - timer expiration message
sending and timer restart/cleanup based on timer state(config).
This also fixes a bug where a one-shot timer message whose delivery
failed once would get lost for good.
Signed-off-by: Andrey Smetanin <asmetanin@virtuozzo.com>
Reviewed-by: Roman Kagan <rkagan@virtuozzo.com>
CC: Gleb Natapov <gleb@kernel.org>
CC: Paolo Bonzini <pbonzini@redhat.com>
CC: Roman Kagan <rkagan@virtuozzo.com>
CC: Denis V. Lunev <den@openvz.org>
CC: qemu-devel@nongnu.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This will be used in future to start Hyper-V SynIC timer
in several places by one logic in one function.
Changes v2:
* drop stimer->count == 0 check inside stimer_start()
* comment stimer_start() assumptions
Signed-off-by: Andrey Smetanin <asmetanin@virtuozzo.com>
Reviewed-by: Roman Kagan <rkagan@virtuozzo.com>
CC: Gleb Natapov <gleb@kernel.org>
CC: Paolo Bonzini <pbonzini@redhat.com>
CC: Roman Kagan <rkagan@virtuozzo.com>
CC: Denis V. Lunev <den@openvz.org>
CC: qemu-devel@nongnu.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The function stimer_stop() is called in one place
so remove the function and replace it's call by function
content.
Signed-off-by: Andrey Smetanin <asmetanin@virtuozzo.com>
Reviewed-by: Roman Kagan <rkagan@virtuozzo.com>
CC: Gleb Natapov <gleb@kernel.org>
CC: Paolo Bonzini <pbonzini@redhat.com>
CC: Roman Kagan <rkagan@virtuozzo.com>
CC: Denis V. Lunev <den@openvz.org>
CC: qemu-devel@nongnu.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
It's possible that guest send us Hyper-V EOM at the middle
of Hyper-V SynIC timer running, so we start processing of Hyper-V
SynIC timers in vcpu context and stop the Hyper-V SynIC timer
unconditionally:
host guest
------------------------------------------------------------------------------
start periodic stimer
start periodic timer
timer expires after 15ms
send expiration message into guest
restart periodic timer
timer expires again after 15 ms
msg slot is still not cleared so
setup ->msg_pending
(1) restart periodic timer
process timer msg and clear slot
->msg_pending was set:
send EOM into host
received EOM
kvm_make_request(KVM_REQ_HV_STIMER)
kvm_hv_process_stimers():
...
stimer_stop()
if (time_now >= stimer->exp_time)
stimer_expiration(stimer);
Because the timer was rearmed at (1), time_now < stimer->exp_time
and stimer_expiration is not called. The timer then never fires.
The patch fixes such situation by not stopping Hyper-V SynIC timer
at all, because it's safe to restart it without stop in vcpu context
and timer callback always returns HRTIMER_NORESTART.
Signed-off-by: Andrey Smetanin <asmetanin@virtuozzo.com>
CC: Gleb Natapov <gleb@kernel.org>
CC: Paolo Bonzini <pbonzini@redhat.com>
CC: Roman Kagan <rkagan@virtuozzo.com>
CC: Denis V. Lunev <den@openvz.org>
CC: qemu-devel@nongnu.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Per Hyper-V specification (and as required by Hyper-V-aware guests),
SynIC provides 4 per-vCPU timers. Each timer is programmed via a pair
of MSRs, and signals expiration by delivering a special format message
to the configured SynIC message slot and triggering the corresponding
synthetic interrupt.
Note: as implemented by this patch, all periodic timers are "lazy"
(i.e. if the vCPU wasn't scheduled for more than the timer period the
timer events are lost), regardless of the corresponding configuration
MSR. If deemed necessary, the "catch up" mode (the timer period is
shortened until the timer catches up) will be implemented later.
Changes v2:
* Use remainder to calculate periodic timer expiration time
Signed-off-by: Andrey Smetanin <asmetanin@virtuozzo.com>
Reviewed-by: Roman Kagan <rkagan@virtuozzo.com>
CC: Gleb Natapov <gleb@kernel.org>
CC: Paolo Bonzini <pbonzini@redhat.com>
CC: "K. Y. Srinivasan" <kys@microsoft.com>
CC: Haiyang Zhang <haiyangz@microsoft.com>
CC: Vitaly Kuznetsov <vkuznets@redhat.com>
CC: Roman Kagan <rkagan@virtuozzo.com>
CC: Denis V. Lunev <den@openvz.org>
CC: qemu-devel@nongnu.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The SynIC message protocol mandates that the message slot is claimed
by atomically setting message type to something other than HVMSG_NONE.
If another message is to be delivered while the slot is still busy,
message pending flag is asserted to indicate to the guest that the
hypervisor wants to be notified when the slot is released.
To make sure the protocol works regardless of where the message
sources are (kernel or userspace), clear the pending flag on SINT ACK
notification, and let the message sources compete for the slot again.
Signed-off-by: Andrey Smetanin <asmetanin@virtuozzo.com>
Reviewed-by: Roman Kagan <rkagan@virtuozzo.com>
CC: Gleb Natapov <gleb@kernel.org>
CC: Paolo Bonzini <pbonzini@redhat.com>
CC: "K. Y. Srinivasan" <kys@microsoft.com>
CC: Haiyang Zhang <haiyangz@microsoft.com>
CC: Vitaly Kuznetsov <vkuznets@redhat.com>
CC: Roman Kagan <rkagan@virtuozzo.com>
CC: Denis V. Lunev <den@openvz.org>
CC: qemu-devel@nongnu.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This helper will be used also in Hyper-V SynIC timers implementation.
Signed-off-by: Andrey Smetanin <asmetanin@virtuozzo.com>
Reviewed-by: Roman Kagan <rkagan@virtuozzo.com>
CC: Gleb Natapov <gleb@kernel.org>
CC: Paolo Bonzini <pbonzini@redhat.com>
CC: "K. Y. Srinivasan" <kys@microsoft.com>
CC: Haiyang Zhang <haiyangz@microsoft.com>
CC: Vitaly Kuznetsov <vkuznets@redhat.com>
CC: Roman Kagan <rkagan@virtuozzo.com>
CC: Denis V. Lunev <den@openvz.org>
CC: qemu-devel@nongnu.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
A new vcpu exit is introduced to notify the userspace of the
changes in Hyper-V SynIC configuration triggered by guest writing to the
corresponding MSRs.
Changes v4:
* exit into userspace only if guest writes into SynIC MSR's
Changes v3:
* added KVM_EXIT_HYPERV types and structs notes into docs
Signed-off-by: Andrey Smetanin <asmetanin@virtuozzo.com>
Reviewed-by: Roman Kagan <rkagan@virtuozzo.com>
Signed-off-by: Denis V. Lunev <den@openvz.org>
CC: Gleb Natapov <gleb@kernel.org>
CC: Paolo Bonzini <pbonzini@redhat.com>
CC: Roman Kagan <rkagan@virtuozzo.com>
CC: Denis V. Lunev <den@openvz.org>
CC: qemu-devel@nongnu.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
SynIC (synthetic interrupt controller) is a lapic extension,
which is controlled via MSRs and maintains for each vCPU
- 16 synthetic interrupt "lines" (SINT's); each can be configured to
trigger a specific interrupt vector optionally with auto-EOI
semantics
- a message page in the guest memory with 16 256-byte per-SINT message
slots
- an event flag page in the guest memory with 16 2048-bit per-SINT
event flag areas
The host triggers a SINT whenever it delivers a new message to the
corresponding slot or flips an event flag bit in the corresponding area.
The guest informs the host that it can try delivering a message by
explicitly asserting EOI in lapic or writing to End-Of-Message (EOM)
MSR.
The userspace (qemu) triggers interrupts and receives EOM notifications
via irqfd with resampler; for that, a GSI is allocated for each
configured SINT, and irq_routing api is extended to support GSI-SINT
mapping.
Changes v4:
* added activation of SynIC by vcpu KVM_ENABLE_CAP
* added per SynIC active flag
* added deactivation of APICv upon SynIC activation
Changes v3:
* added KVM_CAP_HYPERV_SYNIC and KVM_IRQ_ROUTING_HV_SINT notes into
docs
Changes v2:
* do not use posted interrupts for Hyper-V SynIC AutoEOI vectors
* add Hyper-V SynIC vectors into EOI exit bitmap
* Hyper-V SyniIC SINT msr write logic simplified
Signed-off-by: Andrey Smetanin <asmetanin@virtuozzo.com>
Reviewed-by: Roman Kagan <rkagan@virtuozzo.com>
Signed-off-by: Denis V. Lunev <den@openvz.org>
CC: Gleb Natapov <gleb@kernel.org>
CC: Paolo Bonzini <pbonzini@redhat.com>
CC: Roman Kagan <rkagan@virtuozzo.com>
CC: Denis V. Lunev <den@openvz.org>
CC: qemu-devel@nongnu.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
HV_X64_MSR_VP_RUNTIME msr used by guest to get
"the time the virtual processor consumes running guest code,
and the time the associated logical processor spends running
hypervisor code on behalf of that guest."
Calculation of this time is performed by task_cputime_adjusted()
for vcpu task.
Necessary to support loading of winhv.sys in guest, which in turn is
required to support Windows VMBus.
Signed-off-by: Andrey Smetanin <asmetanin@virtuozzo.com>
Reviewed-by: Roman Kagan <rkagan@virtuozzo.com>
Signed-off-by: Denis V. Lunev <den@openvz.org>
CC: Paolo Bonzini <pbonzini@redhat.com>
CC: Gleb Natapov <gleb@kernel.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
HV_X64_MSR_RESET msr is used by Hyper-V based Windows guest
to reset guest VM by hypervisor.
Necessary to support loading of winhv.sys in guest, which in turn is
required to support Windows VMBus.
Signed-off-by: Andrey Smetanin <asmetanin@virtuozzo.com>
Reviewed-by: Roman Kagan <rkagan@virtuozzo.com>
Signed-off-by: Denis V. Lunev <den@openvz.org>
CC: Paolo Bonzini <pbonzini@redhat.com>
CC: Gleb Natapov <gleb@kernel.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This patch introduce Hyper-V related source code file - hyperv.c and
per vm and per vcpu hyperv context structures.
All Hyper-V MSR's and hypercall code moved into hyperv.c.
All Hyper-V kvm/vcpu fields moved into appropriate hyperv context
structures. Copyrights and authors information copied from x86.c
to hyperv.c.
Signed-off-by: Andrey Smetanin <asmetanin@virtuozzo.com>
Signed-off-by: Denis V. Lunev <den@openvz.org>
Reviewed-by: Peter Hornyack <peterhornyack@google.com>
CC: Paolo Bonzini <pbonzini@redhat.com>
CC: Gleb Natapov <gleb@kernel.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
