It's useful to know the MAC address when being
disassociated; fix a typo (missing colon) and
move some messages so we get them only when they
are actually taking effect.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When the queued management work items are processed in
ieee80211_sta_work() an item could be removed. This could change the
anybusy from true to false, so we better check whether we can start a
new scan only after having processed the pending work first.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
After being disassociated by the AP, mac80211 currently
reports this to cfg80211, and then goes to delete the
association. That's fine, but cfg80211 assumes that it's
still authenticated, however, mac80211 throws away all
state.
This fixes mac80211 to keep track of the authentication
in that case so that cfg80211 can request a deauth or
new association properly.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Do a probe request every 30 seconds, and wait for probe response,
half a second This should lower the traffic that card sends, thus save
power Wainting longer for response makes probe more robust against
'slow' access points
Signed-off-by: Maxim Levitsky <maximlevitsky@gmail.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Tested-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Retry 5 times (chosen arbitary ), before assuming
that station is out of range.
Fixes frequent disassociations while connected to weak,
and sometimes even strong access points.
Signed-off-by: Maxim Levitky <maximlevitsky@gmail.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since the bss is always set now once we are connected, if the
bss has its own information element we refer to it and pass that
instead of relying on mac80211's parsing.
Now all cfg80211 drivers get country IE support, automatically and
we reduce the call overhead that we had on mac80211 which called this
upon every beacon and instead now call this only upon a successfull
connection by a STA on cfg80211.
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Some of the recent MLME rework I did broke powersave
because the ps_sdata isn't assigned at the right time,
and the work item wasn't removed from the list before
calling ieee80211_recalc_ps(). To be more specific,
this broke the case where you'd enabled PS before
associating, either automatically or with iwconfig.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The mac80211 workqueue exists to enable mac80211 and drivers
to queue their own work on a single threaded workqueue. mac80211
takes care to flush the workqueue during suspend but we never
really had requirements on drivers for how they should use
the workqueue in consideration for suspend.
We extend mac80211 to document how the mac80211 workqueue should
be used, how it should not be used and finally move raw access to
the workqueue to mac80211 only. Drivers and mac80211 use helpers
to queue work onto the mac80211 workqueue:
* ieee80211_queue_work()
* ieee80211_queue_delayed_work()
These helpers will now warn if mac80211 already completed its
suspend cycle and someone is trying to queue work. mac80211
flushes the mac80211 workqueue prior to suspend a few times,
but we haven't taken the care to ensure drivers won't add more
work after suspend. To help with this we add a warning when
someone tries to add work and mac80211 already completed the
suspend cycle.
Drivers should ensure they cancel any work or delayed work
in the mac80211 stop() callback.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Marcel reported a warning, which quite obviously comes
from an oversight in the code handling deauth frames,
and which resulted in multiple follow-up warnings due
to this missing handling. This patch adds the missing
deauth handling (telling cfg80211 about it) and also
removes the follow-up warnings since they could happen
due to races even if nothing is wrong. I've explained
the races in the comments.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Reported-by: Marcel Holtmann <marcel@holtmann.org>
Tested-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We were issuing probe requests to the associated AP on the wrong
band by having our beacon timer loss trigger while we are scanning.
When we would scan the timer could hit and force us to send a
probe request to the AP but with a chance we'd be on the wrong band.
This leads to finding no usable bitrate but we should not get so
far on the xmit path. We should not be trying to send these probe
request frames so prevent ieee80211_mgd_probe_ap() from sending
these.
As it turns out all callers of ieee80211_mgd_probe_ap() need this
check so we just move the scan check there. This means we can remove
the recenlty added check during ieee80211_sta_monitor_work().
Additionally we now fix a race condition added by the patch
"mac80211: do not monitor the connection while scanning" which
had the same check in ieee80211_sta_conn_mon_timer(). The race
happens because the timer routine *does* a valid check for
scanning but after it queues work into the mac80211 workqueue
the work callback can kick off with scanning enabled and cause
the same issue we were trying to avoid.
The more appropriate solution would be to disable the respective
timers during scan and re-enable them after scan but requires more
complex code and testing.
Cc: Christian Lamparter <chunkeey@web.de>
Cc: Larry Finger <Larry.Finger@lwfinger.net>
Reported-by: Fabio Rossi <rossi.f@inwind.it>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When a new MLME work is created, its timeout is initialised
to 0. This is wrong, it could then be thought of as having
an actual timeout in the future (time_is_after_jiffies() can
return true). Instead, it should be initialised to jiffies
so that it will run right away as soon as the mlme work is
executed.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Reported-by: Luciano Roth Coelho <luciano.coelho@nokia.com>
Reported-by: Alban Browaeys <prahal@yahoo.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use a bitfield to store the current scan mode instead of two boolean
variables {sw,hw}_scanning. This patch does not introduce functional
changes but allows us to enhance the scan flags later (for example
for background scanning).
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
mac80211 constantly monitors the connection to the associated AP
in order to check if it is out of reach/dead.
This is absolutely fine most of the time.
Except when there is a scheduled scan for the whole neighborhood.
After all this path could trigger while scanning on different channel.
Or even worse: this AP probing triggers a WARN_ON in rate_lowest_index
when the scan code did a band transition!
( http://www.kerneloops.org/raw.php?rawid=449304 )
Reported-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Tested-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In "mac80211: monitor the connection" I forgot to
add code to cancel the new timers & work when the
interface is brought down, which isn't a problem
if you just bring it down, but _is_ a problem when
you destroy the interface. Correct this lapse.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
With the recent MLME rework I accidentally removed the connection
monitoring code. In order to add it back, this patch will add new
code to monitor both for beacon loss and for the connection actually
working, with possibly separate triggers.
When no unicast frames have been received from the AP for (currently)
two seconds, we will send the AP a probe request. Also, when we don't
see beacons from the AP for two seconds, we do the same (but those
times need not be the same due to the way the code is now written).
Additionally, clean up the parameters to the ieee80211_set_disassoc()
function that I need here, those are all useless except sdata.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We have, sometimes, multiple things that want to
run but don't have their own timer. Introduce a
new function to mac80211's mlme run_again() that
makes sure that the timer will run again at the
_first_ needed time, use that function and also
properly reprogram the timer once it fired.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This reworks the key operation in cfg80211, and now only
allows, from userspace, configuring keys (via nl80211)
after the connection has been established (in managed
mode), the IBSS been joined (in IBSS mode), at any time
(in AP[_VLAN] modes) or never for all the other modes.
In order to do shared key authentication correctly, it
is now possible to give a WEP key to the AUTH command.
To configure static WEP keys, these are given to the
CONNECT or IBSS_JOIN command directly, for a userspace
SME it is assumed it will configure it properly after
the connection has been established.
Since mac80211 used to check the default key in IBSS
mode to see whether or not the network is protected,
it needs an update in that area, as well as an update
to make use of the WEP key passed to auth() for shared
key authentication.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Over time, a lot of locking issues have crept into
the smarts of cfg80211, so e.g. scan completion can
race against a new scan, IBSS join can race against
leaving an IBSS, etc.
Introduce a new per-interface lock that protects
most of the per-interface data that we need to keep
track of, and sprinkle assertions about that lock
everywhere. Some things now need to be offloaded to
work structs so that we don't require being able to
sleep in functions the drivers call. The exception
to that are the MLME callbacks (rx_auth etc.) that
currently only mac80211 calls because it was easier
to do that there instead of in cfg80211, and future
drivers implementing those calls will, if they ever
exist, probably need to use a similar scheme like
mac80211 anyway...
In order to be able to handle _deauth and _disassoc
properly, introduce a cookie passed to it that will
determine locking requirements.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
After the mac80211 mlme cleanup, we can require that
the MLME functions in cfg80211 can sleep. This will
simplify future work in cfg80211 a lot.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Sit tight. This shakes up the world as you know
it. Let go of your spaghetti tongs, they will no
longer be required, the horrible statemachine in
net/mac80211/mlme.c is no more...
With the cfg80211 SME mac80211 now has much less
to keep track of, but, on the other hand, for FT
it needs to be able to keep track of at least one
authentication being in progress while associated.
So convert from a single state machine to having
small ones for all the different things we need to
do. For real FT it will still need work wrt. PS,
but this should be a good step.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The ap_capab and last_probe struct members are unused.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since we don't really know that well in the kernel,
let's let the SME control whether it wants to use
reassociation or not, by allowing it to give the
previous BSSID in the associate() parameters.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In order to avoid problems with BSS structs going away
while they're in use, I've long wanted to make cfg80211
keep track of them. Without the SME, that wasn't doable
but now that we have the SME we can do this too. It can
keep track of up to four separate authentications and
one association, regardless of whether it's controlled
by the cfg80211 SME or the userspace SME.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This function from mac80211 seems generally useful, and
I will need it in cfg80211 soon.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
With mac80211 now always controlled by an external SME,
a lot of code is dead -- SSID, BSSID, channel selection
is always done externally, etc. Additionally, rename
IEEE80211_STA_TKIP_WEP_USED to IEEE80211_STA_DISABLE_11N
and clean up the code a bit.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The automatic auth algorithm issue is now solved in
cfg80211, so mac80211 no longer needs code to try
different algorithms -- just using whatever cfg80211
asked for is good.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Just on/off and timeout, and with a hacky cfg80211 method
until we figure out what we want, though this is probably
sufficient as we want to use pm_qos for wifi everywhere.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This adds code to make it possible to use the cfg80211
connect() API with wireless extensions, and because the
previous patch added emulation of that API with auth()
and assoc(), by extension also supports wext on that.
At the same time, removes code from mac80211 for wext,
but doesn't yet clean up mac80211's mlme code more.
Signed-off-by: Samuel Ortiz <samuel.ortiz@intel.com>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When the auth algorithm is rejected, but we don't have
another one to try, we will eventually retry but that
isn't useful -- we'll then do it again and again until
we eventually give up. Instead, we should let the SME
know and go into disabled state. The same applies for
situations where the AP rejects with any other status
code.
Additionally, when trying the next auth algorithm, we
should reset the auth_tries so that just a single lost
frame doesn't lead to us giving up on the third auth
algorithm.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Instead of hardcoding GFP_ATOMIC everywhere, add a
new function parameter that gets the flags from the
caller. Obviously then I need to update all callers
(all of them in mac80211), and it turns out that now
it's ok to use GFP_KERNEL in almost all places.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Within mac80211, we often need to copy the rx status into
skb->cb. This is wasteful, as drivers could be building it
in there to start with. This patch changes the API so that
drivers are expected to pass the RX status in skb->cb, now
accessible as IEEE80211_SKB_RXCB(skb). It also updates all
drivers to pass the rx status in there, but only by making
them memcpy() it into place before the call to the receive
function (ieee80211_rx(_irqsafe)). Each driver can now be
optimised on its own schedule.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When changing to a new BSSID or SSID, the code in
ieee80211_set_disassoc() needs to have the old data
still valid to be able to disconnect and clean up
properly. Currently, however, the old data is thrown
away before ieee80211_set_disassoc() is ever called,
so fix that by calling the function _before_ the old
data is overwritten.
This is (one of) the issue(s) causing mac80211 to hold
cfg80211's BSS structs forever, and them thus being
returned in scan results after they're long gone.
http://www.intellinuxwireless.org/bugzilla/show_bug.cgi?id=2015
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If we do not disconnect when a channel switch is requested,
we end up eventually detection beacon loss from the AP and
then disconnecting, without ever really telling the AP, so
we might just as well disconnect right away.
Additionally, this fixes a problem with iwlwifi where the
driver will clear some internal state on channel changes
like this and then get confused when we actually go clear
that state from mac80211.
It may look like this patch drops the no-IBSS check, but
that is already handled by cfg80211 in the wext handler it
provides for IBSS (cfg80211_ibss_wext_siwfreq).
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It looks like some programs (e.g., NM) are setting an empty SSID with
SIOCSIWESSID in some cases. This seems to trigger mac80211 to try to
associate with an invalid configuration (wildcard SSID) which will
result in failing associations (or odd issues, potentially including
kernel panic with some drivers) if the AP were to actually accept this
anyway).
Only start association process if the SSID is actually set. This
speeds up connection with NM in number of cases and avoids sending out
broken association request frames.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When associated, but probing the AP because we detected
beacon loss, we need to disable powersave to be able to
receive the probe response. Change the code to do that by
checking whether we're trying to probe when determining
the possibility of going into PS, and recalculate the PS
ability at the necessary spots.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We don't want to trigger moving between PS mode during scan,
because then we will sometimes end up sending nullfunc frames
during scan. We're supposed to only send one prior to scan
and after scan.
This fixes an oops which occured due to an assert in ath9k:
http://marc.info/?l=linux-wireless&m=124277331319024
The assert was happening because the rate control algorithm
figures it should find at least one valid dual stream or
single stream rate. Since we allow mac80211 to send nullfunc
frames during scan and dynamic PS was enabled at times we ended
up trying to send nullfunc frames for the target sta on the
wrong band for which we have no valid rate to communicate with
it. This breaks the assumptions in rate control.
We determine we also need to disable moving between PS modes
when not associated so lets just add that now as well, and we
should not have a ps_sdata when that interface cannot actually
go into PS because it's not associated.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
My first patch submission used 200ms, which I then somehow
managed to revert back to the earlier 50ms I had used for
some tests in the second patch submission -- but that was
wrong, I should have used 200ms here. Correct that.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In "mac80211: split out and decrease probe wait time" I tried
to reduce the time waiting for a probe response, but failed to
take into account the case where we are detecting beacon loss
in software -- in that case we still wait the monitoring time
rather than the probe wait time. Fix this by refactoring the
mod_timer() calls in ieee80211_associated().
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently, we will ask the driver to configure right away
when somebody changes the desired BSSID. That's totally
strange because then we will configure the driver without
even knowing whether the BSS exists. Change this to only
configure the BSSID when associated, and configure a zero
BSSID when not associated.
As a side effect, this fixes an issue with the iwlwifi
driver which doesn't implement sta_notify properly and
uses the BSSID instead and gets very confused if the
BSSID is cleared before we disassociate, which results
in the warning Marcel posted [1] and iwlwifi bug 1995 [2].
[1] http://thread.gmane.org/gmane.linux.kernel.wireless.general/32598
[2] http://www.intellinuxwireless.org/bugzilla/show_bug.cgi?id=1995
Cc: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When the genIE hasn't changed there's no reason to kick
the state machine since it won't be able to do anything
new -- doing this decreases the useless work we do for
reassociating because if we do kick the state machine
it will try to find a usable BSS but there might not be
one because wpa_supplicant will only change the BSSID
a little later.
In a sense this is a workaround for userspace behaviour,
but on the other hand userspace cannot really keep track
of what the kernel currently has for genIE since any
process could have changed that while wpa_supplicant
wasn't looking.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If the AP includes our AID in the TIM IE, we need to process the
Beacon frame as far as PS is concerned (send PS-Poll or nullfunc data
with PM=0). The previous code skipped this in cases where the CRC
value did not change and it would not change if the AP continues
including our AID in the TIM..
There is no need to count the crc32 value for directed_tim with this
change, so we can remove that part. In order not to change the order
of operations (i.e., update WMM parameters prior to sending PS-Poll),
the CRC match is checked twice as only after the PS processing step,
the rest of the function is skipped if nothing changed in the Beacon.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We forgot to cancel all timers in mac80211 when suspending.
In particular we forgot to deal with some things that can
cause hardware reconfiguration -- while it is down.
While at it we go ahead and add a warning in ieee80211_sta_work()
if its run while the suspend->resume cycle is in effect. This
should not happen and if it does it would indicate there is
a bug lurking in either mac80211 or mac80211 drivers.
With this now wpa_supplicant doesn't blink when I go to suspend
and resume where as before there where issues with some timers
running during the suspend->resume cycle. This caused a lot of
incorrect assumptions and would at times bring back the device
in an incoherent, but mostly recoverable, state.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The channel switch code is currently in the spectrum
management file, where arguably it belongs. However,
it is for managed mode only and uses the structures
for that mode only so having it in a more generic
file can be confusing. Additionally, my next patch
gets simpler with the code here.
When/if we ever implement this for IBSS or mesh then
we will need to rework the structures it uses anyway
at which point we could move the code back.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
While the probe request poll is expected to work, it looks like it
does not always result in getting a response. The exact reason for
this is unclear, but anyway, if we do receive a Beacon frame from our
AP, there is no need to disconnect based on the probereq poll. This
seems to help keep the connection bit more stable in cases where
beacon loss is occurring semi-frequently.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is more consistent with our nl80211 naming convention
for HT40-/+.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg