When system on the suspend state, Some SoC can't get gpio interrupt.
After system resume, need send extcon uevent to userspace.
Signed-off-by: Rongjun Ying <rongjun.ying@csr.com>
Reviewed-by: Barry Song <Baohua.Song@csr.com>
Acked-by: Myungjoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
This patch supports Maxim MAX14577 MUIC(Micro USB Interface Controller)
device by using EXTCON subsystem to handle various external connectors.
The max14577 device uses regmap method for i2c communication and
supports irq domain.
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
wm5110 rev D is the first chip to use headphone detection IP 2, specify
such and make a small correction as the impedance value is actually read
in 0.5 ohm increments now.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
No point in revisiting ranges the detection will be no more accurate
the second time simply report that the resistance is right on the
range boundry.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
The microphone detection code is run as delayed work to provide
additional debounce, it is possible that the jack could have been
removed by the time we process the microphone detection. Turn this
case into a no op.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
We need to make sure we reset back to our starting state, especially
making sure that we have disabled poll in the register cache.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Improve readability by creating a define for each microphone detection
level.
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Always cross check with the ID state and the source of interrupt.
Also add a case in which ID Source is ID_GND but LATCH state is set
wrongly. This uses the previous Link stat to determine the new state.
Signed-off-by: George Cherian <george.cherian@ti.com>
Acked-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
The Palmas device contains only a USB VBUS-ID detector, so added a
compatible type *ti,palmas-usb-vid*. Didn't remove the existing compatible
types for backward compatibility.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Commit 338de0ca (extcon: gpio: Use gpio driver/chip debounce if supported)
introduced a call to gpio_set_debounce() before actually requesting the
respective gpio pin from the gpio subsystem.
The gpio subsystem expects that a gpio pin was requested before modifying its
state. Not doing so results in a warning from gpiolib, and the gpio pin is
auto-requested. This in turn causes the subsequent devm_gpio_request_one()
to fail. So devm_gpio_request_one() must be called prior to calling
gpio_set_debounce().
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
In the case of a device tree system there will be no pdata attached to
the device, causing us to deference a NULL pointer. Better to take the
pdata from the Arizona structure as this will always exist and we know
will have been populated since it is populated by the MFD device which
binds in the extcon driver.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
This patchset modify extcon core to remove unnecessary allocation sequence for
'dev' instance and change extcon_dev_register() interface. extcon-gpio use
gpiolib API to get debounce time and include small fix of extcon core/device
driver.
Detailed description for patchset:
1. Modify extcon core driver
- The extcon-gpio driver use gpio_set_debounce() API provided from gpiolib
if gpio driver for SoC support gpio_set_debounce() function and support 'gpio_
activ_low' filed to check whether gpio active state is 1(high) or 0(low).
- Change field type of 'dev' in structure extcon_dev and remove the sequence
of allocating memory of 'struct dev' on extcon_dev_register() function because
extcon device must need 'struct device.
- Change extcon_dev_register() prototype to simplify it and remove unnecessary
parameter as below:
2. Fix coding style and typo
- extcon core : Fix indentation coding style and remove unnecessary casting
- extcon-max8997 : Fix checkpatch warning
- extcon-max77693 : Fix checkpatch warning
- extcon-arizona : Fix typo of comment and modify minor issue
- extcon-palmas : Use dev_get_platdata()
3. Modify extcon-arizona driver
- Modify minor issue about micbias and comparision statement
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=8Hr2
-----END PGP SIGNATURE-----
Merge tag 'extcon-next-for-3.13' of git://git.kernel.org/pub/scm/linux/kernel/git/chanwoo/extcon into char-misc-next
Chanwoo writes:
Update extcon for 3.13
This patchset modify extcon core to remove unnecessary allocation sequence for
'dev' instance and change extcon_dev_register() interface. extcon-gpio use
gpiolib API to get debounce time and include small fix of extcon core/device
driver.
Detailed description for patchset:
1. Modify extcon core driver
- The extcon-gpio driver use gpio_set_debounce() API provided from gpiolib
if gpio driver for SoC support gpio_set_debounce() function and support 'gpio_
activ_low' filed to check whether gpio active state is 1(high) or 0(low).
- Change field type of 'dev' in structure extcon_dev and remove the sequence
of allocating memory of 'struct dev' on extcon_dev_register() function because
extcon device must need 'struct device.
- Change extcon_dev_register() prototype to simplify it and remove unnecessary
parameter as below:
2. Fix coding style and typo
- extcon core : Fix indentation coding style and remove unnecessary casting
- extcon-max8997 : Fix checkpatch warning
- extcon-max77693 : Fix checkpatch warning
- extcon-arizona : Fix typo of comment and modify minor issue
- extcon-palmas : Use dev_get_platdata()
3. Modify extcon-arizona driver
- Modify minor issue about micbias and comparision statement
This patch remove extcon_dev_register()'s second parameter which means
the pointer of parent device to simplify prototype of this function.
So, if extcon device has the parent device, it should set the pointer of
parent device to edev.dev.parent in extcon device driver instead of in
extcon_dev_register().
Cc: Graeme Gregory <gg@slimlogic.co.uk>
Cc: Kishon Vijay Abraham I <kishon@ti.com>
Cc: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Cc: Mark Brown <broonie@kernel.org>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Myungjoo Ham <myungjoo.ham@samsung.com>
The extcon device must always need 'struct device' so this patch change
field type of 'dev' instead of allocating memory for 'struct device' on
extcon_dev_register() function.
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Myungjoo Ham <cw00.choi@samsung.com>
Every other pdata field is specified unshifted the patch handles
shifting for the MICBIAS from the microphone detection polarity
configurations in the extcon driver rather than demanding it in
pdata to match other fields.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
We should move range when the measured value is greater than or equal to
the max value not when greater than.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
This patch add 'gpio_active_low' field to 'struct gpio_extcon_data'
to check whether gpio active state is 1(high) or 0(low).
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Use the wrapper function for retrieving the platform data instead of
accessing dev->platform_data directly. This is a cosmetic change
to make the code simpler and enhance the readability.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
This patch use gpio_set_debounce() API provided from gpiolib if SoC or device
driver with gpio support gpio_set_debounce() function.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Casting the return value which is a void pointer is redundant.
The conversion from void pointer to any other pointer type is
guaranteed by the C programming language.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Fixes the following warning:
WARNING: space prohibited before semicolon
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
We want the trig_sts bits to be cleared in all cases where we consider
the jack detection interrupt to have been handled. Specifically, if a
duplicate detection event was suppressed these bits were not cleared
causing the CODEC to not enter a low power state. This patch clears the
bits on the duplicate detection code path.
Reported-by: Ryo Tsutsui <ryo.tsutsui@wolfsonmicro.com>
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Fixes the following warning:
WARNING: space prohibited before semicolon
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
This fixes up braces coding style issue by using checkpatch script.
Cc: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Cc: Mark Brown <broonie@kernel.org>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fix 80 column coding sytle issues by using checkpatch script.
Cc: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Cc: Mark Brown <broonie@kernel.org>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Myungjoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here's the big driver core pull request for 3.12-rc1.
Lots of tiny changes here fixing up the way sysfs attributes are
created, to try to make drivers simpler, and fix a whole class race
conditions with creations of device attributes after the device was
announced to userspace.
All the various pieces are acked by the different subsystem maintainers.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.21 (GNU/Linux)
iEYEABECAAYFAlIlIPcACgkQMUfUDdst+ynUMwCaAnITsxyDXYQ4DqEsz8EcOtMk
718AoLrgnUZs3B+70AT34DVktg4HSThk
=USl9
-----END PGP SIGNATURE-----
Merge tag 'driver-core-3.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core patches from Greg KH:
"Here's the big driver core pull request for 3.12-rc1.
Lots of tiny changes here fixing up the way sysfs attributes are
created, to try to make drivers simpler, and fix a whole class race
conditions with creations of device attributes after the device was
announced to userspace.
All the various pieces are acked by the different subsystem
maintainers"
* tag 'driver-core-3.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (119 commits)
firmware loader: fix pending_fw_head list corruption
drivers/base/memory.c: introduce help macro to_memory_block
dynamic debug: line queries failing due to uninitialized local variable
sysfs: sysfs_create_groups returns a value.
debugfs: provide debugfs_create_x64() when disabled
rbd: convert bus code to use bus_groups
firmware: dcdbas: use binary attribute groups
sysfs: add sysfs_create/remove_groups for when SYSFS is not enabled
driver core: add #include <linux/sysfs.h> to core files.
HID: convert bus code to use dev_groups
Input: serio: convert bus code to use drv_groups
Input: gameport: convert bus code to use drv_groups
driver core: firmware: use __ATTR_RW()
driver core: core: use DEVICE_ATTR_RO
driver core: bus: use DRIVER_ATTR_WO()
driver core: create write-only attribute macros for devices and drivers
sysfs: create __ATTR_WO()
driver-core: platform: convert bus code to use dev_groups
workqueue: convert bus code to use dev_groups
MEI: convert bus code to use dev_groups
...
The debounce timeout is generally quite long and the work not performance
critical so allow the scheduler to run the work anywhere rather than in
the normal per-CPU workqueue.
Signed-off-by: Mark Brown <broonie@linaro.org>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Myungjoo Ham <myungjoo.ham@samsung.com>
The debounce timeout is generally quite long and the work not performance
critical so allow the scheduler to run the work anywhere rather than in
the normal per-CPU workqueue.
Signed-off-by: Mark Brown <broonie@linaro.org>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Myungjoo Ham <myungjoo.ham@samsung.com>
None of the delayed work the driver schedules has particularly short delays
and it is not performance sensitive so let the scheduler run it wherever
is most efficient rather than in a per CPU workqueue by using the system
power efficient workqueue.
Signed-off-by: Mark Brown <broonie@linaro.org>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Myungjoo Ham <myungjoo.ham@samsung.com>
Based on system design, platform needs to detect the VBUS or ID or
both. Provide option to select this through platform data to
disable part of cable detection through palmas-usb.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Acked-by: Graeme Gregory <gg@slimlogic.co.uk>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Myungjoo Ham <myungjoo.ham@samsung.com>
Add suspend/resume callbacks and support for wakeup from
suspend on USB HOST or USB Device cable insertion or removal.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Acked-by: Graeme Gregory <gg@slimlogic.co.uk>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Myungjoo Ham <myungjoo.ham@samsung.com>
When integrating driver with Tegra platform, it is found that
the ID pins get detected only once after booting system and
further removal and re-insert does not detect the ID pin.
Fixing this issue with enabling interrupt on ID_GND and ID_FLOAT
always and clearing the status on LATCH register which actually
occurred.
Also if interrupt occurs with line status as zero then based on
previous status, set the cable state.
Add debug prints to display the cable state when any cable
insertion/removal happen.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Acked-by: Graeme Gregory <gg@slimlogic.co.uk>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Myungjoo Ham <myungjoo.ham@samsung.com>
of_extcon_get_extcon_dev() uses dev_name for getting the reference
to the extcon device. If the extcon driver assigns a different
name other than dev_name, of_extcon_get_extcon_dev() wouldn't
be able to find the reference to the extcon device. Since the
client drivers of extcon-palmas would be using
of_extcon_get_extcon_dev(), removed assigning edev.name
in extcon-palmas.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Myungjoo Ham <myungjoo.ham@samsung.com>
Added an API of_extcon_get_extcon_dev() to be used by drivers to get
extcon device in the case of dt boot (this can be used instead of
extcon_get_extcon_dev()).
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Myungjoo Ham <myungjoo.ham@samsung.com>
The dev_attrs field of struct class is going away soon, dev_groups
should be used instead. This converts the extcon_class code to use the
correct field.
Cc: MyungJoo Ham <myungjoo.ham@samsung.com>
Acked-by: Chanwoo Choi<cw00.choi@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Calling dev_set_name with a single paramter causes it to be handled as a
format string. Many callers are passing potentially dynamic string
content, so use "%s" in those cases to avoid any potential accidents,
including wrappers like device_create*() and bdi_register().
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This is the driver for the USB comparator built into the palmas chip. It
handles the various USB OTG events that can be generated by cable
insertion/removal.
Signed-off-by: Graeme Gregory <gg@slimlogic.co.uk>
Signed-off-by: Moiz Sonasath <m-sonasath@ti.com>
Signed-off-by: Ruchika Kharwar <ruchika@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: George Cherian <george.cherian@ti.com>
[kishon@ti.com: adapted palmas usb driver to use the extcon framework]
Signed-off-by: Sebastien Guiriec <s-guiriec@ti.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Myungjoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Added EXPORT_SYMBOL_GPL() for extcon_register_interest and
extcon_register_notifier in order to avoid undefined reference
error when building the consumer modules of extcon as _modules_.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Myungjoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch change permission from read/write to only read.
The specific process in the user-space couldn't change the state
of cable when cable is attached or detached.
- /sys/class/extcon/[devine name]/state
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Myungjoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
GENERIC_GPIO now synonymous with GPIOLIB. There are no longer any valid
cases for enableing GENERIC_GPIO without GPIOLIB, even though it is
possible to do so which has been causing confusion and breakage. This
branch does the work to completely eliminate GENERIC_GPIO.
However, it is not trivial to just create a branch to remove it. Over
the course of the v3.9 cycle more code referencing GENERIC_GPIO has been
added to linux-next that conflicts with this branch. The following must
be done to resolve the conflicts when merging this branch into mainline:
* "git grep CONFIG_GENERIC_GPIO" should return 0 hits. Matches should be
replaced with CONFIG_GPIOLIB
* "git grep '\bGENERIC_GPIO\b'" should return 1 hit in the Chinese
documentation.
* Selectors of GENERIC_GPIO should be turned into selectors of GPIOLIB
* definitions of the option in architecture Kconfig code should be deleted.
Stephen has 3 merge fixup patches[1] that do the above. They are currently
applicable on mainline as of May 2nd.
[1] http://www.mail-archive.com/linux-kernel@vger.kernel.org/msg428056.html
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=xodc
-----END PGP SIGNATURE-----
Merge tag 'gpio-for-linus' of git://git.secretlab.ca/git/linux
Pull removal of GENERIC_GPIO from Grant Likely:
"GENERIC_GPIO now synonymous with GPIOLIB. There are no longer any
valid cases for enableing GENERIC_GPIO without GPIOLIB, even though it
is possible to do so which has been causing confusion and breakage.
This branch does the work to completely eliminate GENERIC_GPIO."
* tag 'gpio-for-linus' of git://git.secretlab.ca/git/linux:
gpio: update gpio Chinese documentation
Remove GENERIC_GPIO config option
Convert selectors of GENERIC_GPIO to GPIOLIB
blackfin: force use of gpiolib
m68k: coldfire: use gpiolib
mips: pnx833x: remove requirement for GENERIC_GPIO
openrisc: default GENERIC_GPIO to false
avr32: default GENERIC_GPIO to false
xtensa: remove explicit selection of GENERIC_GPIO
sh: replace CONFIG_GENERIC_GPIO by CONFIG_GPIOLIB
powerpc: remove redundant GENERIC_GPIO selection
unicore32: default GENERIC_GPIO to false
unicore32: remove unneeded select GENERIC_GPIO
arm: plat-orion: use GPIO driver on CONFIG_GPIOLIB
arm: remove redundant GENERIC_GPIO selection
mips: alchemy: require gpiolib
mips: txx9: change GENERIC_GPIO to GPIOLIB
mips: loongson: use GPIO driver on CONFIG_GPIOLIB
mips: remove redundant GENERIC_GPIO select
GENERIC_GPIO is now equivalent to GPIOLIB and features that depended on
GENERIC_GPIO can now depend on GPIOLIB to allow removal of this option.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
MAX77693 extcon driver
- Add 'static' keryword to internal data structure
- Fix return value using 'ret' instead of hardcoding
MAX8997 extcon driver
- Use dev_err() instead of pr_err()
- Fix return value using 'ret' instead of hardcoding
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=vnWV
-----END PGP SIGNATURE-----
Merge tag 'extcon-for-3.10' of git://git.kernel.org/pub/scm/linux/kernel/git/chanwoo/extcon into char-misc-next
Chanwoo writes:
This is small fixes for extcon driver.
MAX77693 extcon driver
- Add 'static' keryword to internal data structure
- Fix return value using 'ret' instead of hardcoding
MAX8997 extcon driver
- Use dev_err() instead of pr_err()
- Fix return value using 'ret' instead of hardcoding
Return the value obtained from the function instead of hardcoding.
Fixes the following warnings:
drivers/extcon/extcon-max8997.c:235 max8997_muic_set_path() info:
why not propagate 'ret' from max8997_update_reg() instead of (-11)?
drivers/extcon/extcon-max8997.c:248 max8997_muic_set_path() info:
why not propagate 'ret' from max8997_update_reg() instead of (-11)?
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Myungjoo Ham <myungjoo.ham@samsung.com>
Return the value obtained from the function instead of hardcoding.
Silences the following warnings:
drivers/extcon/extcon-max77693.c:297 max77693_muic_set_path()
info: why not propagate 'ret' from max77693_update_reg() instead of (-11)?
drivers/extcon/extcon-max77693.c:310 max77693_muic_set_path()
info: why not propagate 'ret' from max77693_update_reg() instead of (-11)?
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Myungjoo Ham <myungjoo.ham@samsung.com>
dev_err() is more preferred than pr_err().
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Myungjoo Ham <myungjoo.ham@samsung.com>
Rongjun Ying