This add the product id of the touch screen found on ACER Aspire 5738PZ. Works
with hid-cando driver.
Signed-off-by: Francois Jaouen<francois.jaouen@laposte.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
... but produce a big warning about the problem as encouragement
for people to fix their drivers.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
When channel_disable() is called, it disables per channel interrupts and
waits until channels state becomes STATE_STALL, and then disables the
channel. Now, if the DMA transfer is disabled while the channel is in
STATE_NEXT we will not wait anything and disable the channel immediately.
This seems to cause weird data corruption for example in audio transfers.
Fix is to wait while we are in STATE_NEXT or STATE_ON and only then
disable the channel.
Signed-off-by: Mika Westerberg <mika.westerberg@iki.fi>
Acked-by: Ryan Mallon <ryan@bluewatersys.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This should pass "buf" to bvec_kunmap_irq() instead of "bv". The api is
like kmap_atomic() instead of kmap().
Signed-off-by: Dan Carpenter <error27@gmail.com>
Acked-by: Geoff Levand <geoff@infradead.org>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
Time stamps for the ring buffer are created by the difference between
two events. Each page of the ring buffer holds a full 64 bit timestamp.
Each event has a 27 bit delta stamp from the last event. The unit of time
is nanoseconds, so 27 bits can hold ~134 milliseconds. If two events
happen more than 134 milliseconds apart, a time extend is inserted
to add more bits for the delta. The time extend has 59 bits, which
is good for ~18 years.
Currently the time extend is committed separately from the event.
If an event is discarded before it is committed, due to filtering,
the time extend still exists. If all events are being filtered, then
after ~134 milliseconds a new time extend will be added to the buffer.
This can only happen till the end of the page. Since each page holds
a full timestamp, there is no reason to add a time extend to the
beginning of a page. Time extends can only fill a page that has actual
data at the beginning, so there is no fear that time extends will fill
more than a page without any data.
When reading an event, a loop is made to skip over time extends
since they are only used to maintain the time stamp and are never
given to the caller. As a paranoid check to prevent the loop running
forever, with the knowledge that time extends may only fill a page,
a check is made that tests the iteration of the loop, and if the
iteration is more than the number of time extends that can fit in a page
a warning is printed and the ring buffer is disabled (all of ftrace
is also disabled with it).
There is another event type that is called a TIMESTAMP which can
hold 64 bits of data in the theoretical case that two events happen
18 years apart. This code has not been implemented, but the name
of this event exists, as well as the structure for it. The
size of a TIMESTAMP is 16 bytes, where as a time extend is only
8 bytes. The macro used to calculate how many time extends can fit on
a page used the TIMESTAMP size instead of the time extend size
cutting the amount in half.
The following test case can easily trigger the warning since we only
need to have half the page filled with time extends to trigger the
warning:
# cd /sys/kernel/debug/tracing/
# echo function > current_tracer
# echo 'common_pid < 0' > events/ftrace/function/filter
# echo > trace
# echo 1 > trace_marker
# sleep 120
# cat trace
Enabling the function tracer and then setting the filter to only trace
functions where the process id is negative (no events), then clearing
the trace buffer to ensure that we have nothing in the buffer,
then write to trace_marker to add an event to the beginning of a page,
sleep for 2 minutes (only 35 seconds is probably needed, but this
guarantees the bug), and then finally reading the trace which will
trigger the bug.
This patch fixes the typo and prevents the false positive of that warning.
Reported-by: Hans J. Koch <hjk@linutronix.de>
Tested-by: Hans J. Koch <hjk@linutronix.de>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Stable Kernel <stable@kernel.org>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
I see the following error message in my kernel log from time to time:
radeon 0000:07:00.0: ffff88007c334000 reserve failed for wait
radeon 0000:07:00.0: ffff88007c334000 reserve failed for wait
After investigation, it turns out that there's nothing to be afraid of
and everything works as intended. So remove the spurious log message.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Reviewed-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Make TV standard and DFP table revisions debug only.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
These bits are used for internal communication and should
be left enabled. This may fix s/r issues on some systems.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
We should not allocate any object into unmappable vram if we
have no means to access them which on all GPU means having the
CP running and on newer GPU having the blit utility working.
This patch limit the vram allocation to visible vram until
we have acceleration up and running.
Note that it's more than unlikely that we run into any issue
related to that as when acceleration is not woring userspace
should allocate any object in vram beside front buffer which
should fit in visible vram.
V2 use real_vram_size as mc_vram_size could be bigger than
the actual amount of vram
[airlied: fixup r700_cp_stop case]
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
perf events: repair incorrect use of copy_from_user
This makes the perf_event_period() return 0 instead of
-EFAULT on success.
Signed-off-by: John Blackwood<john.blackwood@ccur.com>
Signed-off-by: Joe Korty <joe.korty@ccur.com>
Acked-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
LKML-Reference: <20100928220311.GA18145@tsunami.ccur.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This device generates ABS_Z and ABS_RX events, while it should be
generating ABS_X and ABS_Y instead. Using the MULTI_INPUT quirk solves
this issue.
Reference: https://bugs.launchpad.net/ubuntu/+bug/620609/
Signed-off-by: Pierre BAILLY <pierre@substantiel.fr>
Signed-off-by: Anisse Astier <anisse@astier.eu>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This patch disables the fanotify syscalls by just not building them and
letting the cond_syscall() statements in kernel/sys_ni.c redirect them
to sys_ni_syscall().
It was pointed out by Tvrtko Ursulin that the fanotify interface did not
include an explicit prioritization between groups. This is necessary
for fanotify to be usable for hierarchical storage management software,
as they must get first access to the file, before inotify-like notifiers
see the file.
This feature can be added in an ABI compatible way in the next release
(by using a number of bits in the flags field to carry the info) but it
was suggested by Alan that maybe we should just hold off and do it in
the next cycle, likely with an (new) explicit argument to the syscall.
I don't like this approach best as I know people are already starting to
use the current interface, but Alan is all wise and noone on list backed
me up with just using what we have. I feel this is needlessly ripping
the rug out from under people at the last minute, but if others think it
needs to be a new argument it might be the best way forward.
Three choices:
Go with what we got (and implement the new feature next cycle). Add a
new field right now (and implement the new feature next cycle). Wait
till next cycle to release the ABI (and implement the new feature next
cycle). This is number 3.
Signed-off-by: Eric Paris <eparis@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
commit 511d22247b (tg3: 64 bit stats on all arches), overlooked the
rx_dropped accounting.
We use a full "struct rtnl_link_stats64" to hold rx_dropped value, but
forgot to report it in tg3_get_stats64().
Use an "unsigned long" instead to shrink "struct tg3" by 176 bytes, and
report this value to stats readers.
Increment rx_dropped counter for oversized frames.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
CC: Michael Chan <mchan@broadcom.com>
CC: Matt Carlson <mcarlson@broadcom.com>
Acked-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For carrier detection to work properly when binding the driver with a cable
unplugged, netif_carrier_off() should be called after register_netdev(),
not before.
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Russ reported SGI UV is broken recently. He said:
| The SRAT table shows that memory range is spread over two nodes.
|
| SRAT: Node 0 PXM 0 100000000-800000000
| SRAT: Node 1 PXM 1 800000000-1000000000
| SRAT: Node 0 PXM 0 1000000000-1080000000
|
|Previously, the kernel early_node_map[] would show three entries
|with the proper node.
|
|[ 0.000000] 0: 0x00100000 -> 0x00800000
|[ 0.000000] 1: 0x00800000 -> 0x01000000
|[ 0.000000] 0: 0x01000000 -> 0x01080000
|
|The problem is recent community kernel early_node_map[] shows
|only two entries with the node 0 entry overlapping the node 1
|entry.
|
| 0: 0x00100000 -> 0x01080000
| 1: 0x00800000 -> 0x01000000
After looking at the changelog, Found out that it has been broken for a while by
following commit
|commit 8716273cae
|Author: David Rientjes <rientjes@google.com>
|Date: Fri Sep 25 15:20:04 2009 -0700
|
| x86: Export srat physical topology
Before that commit, register_active_regions() is called for every SRAT memory
entry right away.
Use nodememblk_range[] instead of nodes[] in order to make sure we
capture the actual memory blocks registered with each node. nodes[]
contains an extended range which spans all memory regions associated
with a node, but that does not mean that all the memory in between are
included.
Reported-by: Russ Anderson <rja@sgi.com>
Tested-by: Russ Anderson <rja@sgi.com>
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
LKML-Reference: <4CB27BDF.5000800@kernel.org>
Acked-by: David Rientjes <rientjes@google.com>
Cc: <stable@kernel.org> 2.6.33 .34 .35 .36
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Several other ethtool functions leave heap uncleared (potentially) by
drivers. Some interfaces appear safe (eeprom, etc), in that the sizes
are well controlled. In some situations (e.g. unchecked error conditions),
the heap will remain unchanged in areas before copying back to userspace.
Note that these are less of an issue since these all require CAP_NET_ADMIN.
Cc: stable@kernel.org
Signed-off-by: Kees Cook <kees.cook@canonical.com>
Acked-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stanse found that i2400m_rx frees skb, but still uses skb->len even
though it has skb_len defined. So use skb_len properly in the code.
And also define it unsinged int rather than size_t to solve
compilation warnings.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Inaky Perez-Gonzalez <inaky.perez-gonzalez@intel.com>
Cc: linux-wimax@intel.com
Acked-by: Inaky Perez-Gonzalez <inaky.perez-gonzalez@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stanse found that ia_init_one locks a spinlock and inside of that it
calls ia_start which calls:
* request_irq
* tx_init which does kmalloc(GFP_KERNEL)
Both of them can thus sleep and result in a deadlock. I don't see a
reason to have a per-device spinlock there which is used only there
and inited right before the lock location. So remove it completely.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Chas Williams <chas@cmf.nrl.navy.mil>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stanse found that mpc_push frees skb and then it dereferences it. It
is a typo, new_skb should be dereferenced there.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stanse found we do in console_show:
kfree_skb(skb);
return skb->len;
which is not good. Fix that by remembering the len and use it in the
function instead.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Chas Williams <chas@cmf.nrl.navy.mil>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'rc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild-2.6:
kbuild: fix oldnoconfig to do the right thing
kconfig: Temporarily disable dependency warnings
kconfig: delay symbol direct dependency initialization
* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mjg59/platform-drivers-x86:
IPS driver: Fix limit clamping when reducing CPU power
[PATCH 2/2] IPS driver: disable CPU turbo
IPS driver: apply BIOS provided CPU limit if different from default
intel_ips -- ensure we do not enable gpu turbo mode without driver linkage
intel_ips: Print MCP limit exceeded values.
IPS driver: verify BIOS provided limits
IPS driver: don't toggle CPU turbo on unsupported CPUs
NULL pointer might be used in ips_monitor()
Release symbol on error-handling path of ips_get_i915_syms()
old_cpu_power is wrongly divided by 65535 in ips_monitor()
seqno mask of THM_ITV register is 16bit
BugLink: https://bugs.launchpad.net/bugs/653420
Add another HP DV6 notebook (103c:363e) to use STAC_HP_DV5.
Signed-off-by: Luke Yelavich <luke.yelavich@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
We shouldn't return directly here because we're still holding the
&soundcard_mutex.
This bug goes all the way back to the start of git. It's strange that
no one has complained about it as a runtime bug.
CC: stable@kernel.org
Signed-off-by: Dan Carpenter <error27@gmail.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The VMCB is reset whenever we receive a startup IPI, so Linux is setting
TSC back to zero happens very late in the boot process and destabilizing
the TSC. Instead, just set TSC to zero once at VCPU creation time.
Why the separate patch? So git-bisect is your friend.
Signed-off-by: Zachary Amsden <zamsden@redhat.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
On reset, VMCB TSC should be set to zero. Instead, code was setting
tsc_offset to zero, which passes through the underlying TSC.
Signed-off-by: Zachary Amsden <zamsden@redhat.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
This fixes possible cases of not collecting valid error info in
the MCE error thresholding groups on F10h hardware.
The current code contains a subtle problem of checking only the
Valid bit of MSR0000_0413 (which is MC4_MISC0 - DRAM
thresholding group) in its first iteration and breaking out if
the bit is cleared.
But (!), this MSR contains an offset value, BlkPtr[31:24], which
points to the remaining MSRs in this thresholding group which
might contain valid information too. But if we bail out only
after we checked the valid bit in the first MSR and not the
block pointer too, we miss that other information.
The thing is, MC4_MISC0[BlkPtr] is not predicated on
MCi_STATUS[MiscV] or MC4_MISC0[Valid] and should be checked
prior to iterating over the MCI_MISCj thresholding group,
irrespective of the MC4_MISC0[Valid] setting.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
Cc: <stable@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
with hardware slow in negotiation, the system did freeze
while trying to mount root on nfs at boot time.
the link state has not been initialised so network stack
tried to start transmission right away. this caused instant
retries, as the driver solely stated business upon link down,
rendering the system unusable.
notify carrier off initially to prevent transmission until
phylib will report link up.
Signed-off-by: Oskar Schirmer <oskar@linutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently the pressure range in Cintiq 21UX2 is limited to half of the
supported. This patch fixes the problem.
Signed-off-by: Aristeu Rozanski <aris@redhat.com>
Acked-by: Ping Cheng <pingc@wacom.com>
CC: stable@kernel.org
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Commit 861b4ea4 broke oldnoconfig when removed the oldnoconfig checks on
if (input_mode == nonint_oldconfig ||
input_mode == oldnoconfig) {
if (input_mode == nonint_oldconfig &&
sym->name &&
!sym_is_choice_value(sym)) {
to avoid oldnoconfig chugging through the else stanza.
Fix that to restore expected behaviour (which I've confirmed in the
Fedora kernel build that the configs end up looking the same.)
Signed-off-by: Kyle McMartin <kyle@redhat.com>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Michal Marek <mmarek@suse.cz>
After fixing a use-after-free bug in kconfig, a 'make defconfig' or
'make allmodconfig' fills the screen with warnings that were not
detected before. Given that we are close to the release now, disable the
warnings temporarily and deal with them after 2.6.36.
Signed-off-by: Michal Marek <mmarek@suse.cz>
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6:
ACPI: add DMI to disable AML Vista compatibility on MSI GX723 Notebook
ACPI: Handle ACPI0007 Device in acpi_early_set_pdc
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph-client:
ceph: update issue_seq on cap grant
ceph: send cap release message early on failed revoke.
ceph: Update max_len with minimum required size
ceph: Fix return value of encode_fh function
ceph: avoid null deref in osd request error path
ceph: fix list_add usage on unsafe_writes list
* 'drm-intel-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/ickle/drm-intel:
drm/i915: Prevent module unload to avoid random memory corruption
* 's5p-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
ARM: SAMSUNG: Add a workaround for get_clock() for serial driver
ARM: S5P: Bug fix on errors of build with CONFIG_PREEMPT_NONE
ARM: SAMSUNG: Fix build warnings because of unused codes
Define an _addr_lsb field in the mips and ia64 siginfo_ts, following
the asm-generic version. This just puts the field over padding.
This fixes a compilation problem introduced with a337fda.
Cc: ralf@linux-mips.org
Cc: tony.luck@intel.com
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Must drop reference taken by blk_make_request().
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Cc: stable@kernel.org # .35.x
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Use DMA API as PCI equivalents will be deprecated. This change also
allow to allocate with GFP_KERNEL where possible.
Tested-by: Neal Becker <ndbecker2@gmail.com>
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We have fedora bug report where driver fail to initialize after
suspend/resume because of memory allocation errors:
https://bugzilla.redhat.com/show_bug.cgi?id=629158
To fix use GFP_KERNEL allocation where possible.
Tested-by: Neal Becker <ndbecker2@gmail.com>
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
