Commit Graph

495 Commits

Author SHA1 Message Date
Johannes Berg 18b559d5db mac80211: split TX aggregation stop action
When TX aggregation is stopped, there are a few
different cases:
 - connection with the peer was dropped
 - session stop was requested locally
 - session stop was requested by the peer
 - connection was dropped while a session is stopping

The behaviour in these cases should be different, if
the connection is dropped then the driver should drop
all frames, otherwise the frames may continue to be
transmitted, aggregated in the case of a locally
requested session stop or unaggregated in the case of
the peer requesting session stop.

Split these different cases so that the driver can
act accordingly; however, treat local and remote stop
the same way and ask the driver to not send frames as
aggregated packets any more.

In the case of connection drop, the stop callback the
driver is otherwise supposed to call is no longer
required.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2013-01-03 13:01:42 +01:00
Johannes Berg 8a61af65c6 mac80211: fix channel context iteration
During suspend/resume channel contexts might be
iterated even if they haven't been re-added to
the driver, keep track of this and skip them in
iteration. Also use the new status for sanity
checks.

Also clarify the fact that during HW restart all
contexts are iterated over (thanks Eliad.)

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2013-01-03 13:01:35 +01:00
Stanislaw Gruszka 5b632fe85e mac80211: introduce IEEE80211_HW_TEARDOWN_AGGR_ON_BAR_FAIL
Commit f0425beda4 "mac80211: retry sending
failed BAR frames later instead of tearing down aggr" caused regression
on rt2x00 hardware (connection hangs). This regression was fixed by
commit be03d4a45c "rt2x00: Don't let
mac80211 send a BAR when an AMPDU subframe fails". But the latter
commit caused yet another problem reported in
https://bugzilla.kernel.org/show_bug.cgi?id=42828#c22

After long discussion in this thread:
http://mid.gmane.org/20121018075615.GA18212@redhat.com
and testing various alternative solutions, which failed on one or other
setup, we have no other good fix for the issues like just revert both
mentioned earlier commits.

To do not affect other hardware which benefit from commit
f0425beda4, instead of reverting it,
introduce flag that when used will restore mac80211 behaviour before
the commit.

Cc: stable@vger.kernel.org
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
[replaced link with mid.gmane.org that has message-id]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2012-12-05 09:53:31 +01:00
Simon Wunderlich 5d7fad48ca mac80211: Fix typo in mac80211.h
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2012-12-03 11:21:40 +01:00
Johannes Berg b9a9ada14a mac80211: remove probe response temporary buffer allocation
Instead of allocating a temporary buffer to build IEs
build them right into the SKB.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2012-11-30 13:41:27 +01:00
Johannes Berg 5164892184 mac80211: support (partial) VHT radiotap information
Add some information that we have about VHT to radiotap.
This at least lets one see the MCS and NSS information.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2012-11-27 11:56:18 +01:00
Johannes Berg 8bc83c2463 mac80211: support VHT rates in TX info
To achieve this, limit the number of retries to
31 (instead of 255) and use the three bits that
are then free for VHT flags.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2012-11-26 12:43:00 +01:00
Johannes Berg 5614618ec4 mac80211: support drivers reporting VHT RX
Add support to mac80211 for having drivers report
received VHT MCS information.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2012-11-26 12:42:59 +01:00
Johannes Berg 4bf88530be mac80211: convert to channel definition struct
Convert mac80211 (and where necessary, some drivers a
little bit) to the new channel definition struct.

This will allow extending mac80211 for VHT, which is
currently restricted to channel contexts since there
are no drivers using that which makes it easier. As
I also don't care about VHT for drivers not using the
channel context API, I won't convert the previous API
to VHT support.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2012-11-26 12:42:59 +01:00
Johannes Berg 42d97a599e cfg80211: remove remain-on-channel channel type
As mwifiex (and mac80211 in the software case) are the
only drivers actually implementing remain-on-channel
with channel type, userspace can't be relying on it.
This is the case, as it's used only for P2P operations
right now.

Rather than adding a flag to tell userspace whether or
not it can actually rely on it, simplify all the code
by removing the ability to use different channel types.
Leave only the validation of the attribute, so that if
we extend it again later (with the needed capability
flag), it can't break userspace sending invalid data.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2012-11-26 12:42:58 +01:00
Sujith Manoharan 77d2ece6fd mac80211: Add debugfs callbacks for station addition/removal
Provide drivers with hooks to create debugfs files when
a new station is added. This would help drivers to take
advantage of mac80211's station list infrastructure and not maintain
tedious station management code internally.

Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
[ifdef inline wrapper functions]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2012-11-21 11:46:25 +01:00
Eliad Peller 4988456862 mac80211: make remain_on_channel() op pass vif param
Drivers (e.g. wl12xx) might need to know the vif
to roc on (mainly in order to configure the
rx filters correctly).

Add the vif to the op params, and update the current
users (iwlwifi) to use the new api.

Signed-off-by: Eliad Peller <eliad@wizery.com>
[fix hwsim]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2012-11-19 16:20:37 +01:00
Johannes Berg 90b9e446fb mac80211: support radiotap vendor namespace RX data
In some cases, in particular for experimentation, it
can be useful to be able to add vendor namespace data
to received frames in addition to the normal radiotap
data.

Allow doing this through mac80211 by adding fields to
the RX status descriptor that describe the data while
the data itself is prepended to the frame.

Also add some example code to hwsim, but don't enable
it because it doesn't use a proper OUI identifier.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2012-11-19 15:45:46 +01:00
Thomas Pedersen f4bda337bb mac80211: support RX_FLAG_MACTIME_END
Allow drivers to indicate their mactime is at RX completion and adjust
for this in mac80211. Also rename the existing RX_FLAG_MACTIME_MPDU to
RX_FLAG_MACTIME_START to clarify its intent. Based on similar code by
Johannes Berg.

Signed-off-by: Thomas Pedersen <thomas@cozybit.com>
[fix docs, atheros drivers]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2012-11-13 21:43:55 +01:00
Johannes Berg 8b2c98243e mac80211: clarify interface iteration and make it configurable
During hardware restart, all interfaces are iterated even
though they haven't been re-added to the driver, document
this behaviour. The same also happens during resume, which
is even more confusing since all of the interfaces were
previously removed from the driver. Make this optional so
drivers relying on the current behaviour can still use it,
but to let drivers that don't want this behaviour disable
it.

Also convert all API users, keeping the old semantics
except in hwsim, where the new normal ones are desired.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2012-11-09 17:34:35 +01:00
Johannes Berg 9214ad7f9a mac80211: call driver method when restart completes
When the driver requests a restart (reconfiguration) it
gets all the normal method calls, but can't really tell
why they're happening. Call a new restart_complete op
in the driver when the restart completes, so it could
keep its own state about the restart and clear it there.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2012-11-09 17:34:35 +01:00
Johannes Berg 488dd7b53d mac80211: pass P2P powersave parameters to driver
While connected to a GO, parse the P2P NoA attribute
and pass the CT Window and opportunistic powersave
parameters to the driver.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2012-11-06 13:25:06 +01:00
Johannes Berg 1ea6f9c0d4 mac80211: handle TX power per virtual interface
Even before channel contexts/multi-channel, having a
single global TX power limit was already problematic,
in particular if two managed interfaces connected to
two APs with different power constraints. The channel
context introduction completely broke this though and
in fact I had disabled TX power configuration there
for drivers using channel contexts.

Change everything to track TX power per interface so
that different user settings and different channel
maxima are treated correctly. Also continue tracking
the global TX power though for compatibility with
applications that attempt to configure the wiphy's
TX power globally.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2012-10-30 09:11:34 +01:00
Johannes Berg 1041638f2b mac80211: add explicit AP/GO driver operations
Depending on the driver, a lot of setup may be
necessary to start operating as an AP, some of
which may fail. Add an explicit AP start driver
method to make such failures easier to handle,
and add an AP stop driver method for symmetry.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2012-10-26 12:57:06 +02:00
Assaf Krauss 5d0d04e477 mac80211: expose AES-CMAC subkey calculation
Expose a function for the AES-CMAC subkey calculation
to drivers. This is the first step of the AES-CMAC
cipher key setup and may be required for CMAC hardware
offloading.

Signed-off-by: Assaf Krauss <assaf.krauss@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2012-10-23 19:52:52 +02:00
Sujith Manoharan c13a765bd9 mac80211: Notify new IBSS network creation
Initialization of beacon transmission in IBSS mode depends
on whether a new BSS is being created or joined. When joining
an existing IBSS network, beaconing has to start only after
a TSF-sync has happened - this is explained in 11.1.4.

Introduce a new parameter in the BSS information structure to
indicate creator/joiner mode.

Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2012-10-18 09:01:53 +02:00
Mahesh Palivela 818255ea47 mac80211: VHT peer STA caps
Save the AP's VHT capabilities (in managed
mode) and make them available to the driver
in the station information.

Unlike HT capabilities, they aren't restricted
to the common capabilities, so drivers must be
aware of their own capabilities.

Signed-off-by: Mahesh Palivela <maheshp@posedge.com>
[fix endian conversion bug ...]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2012-10-17 11:02:14 +02:00
Johannes Berg 3448c00583 mac80211: add channel context iterator
Drivers may need to iterate the active channel
contexts, export an iterator function to allow
that. To make it possible, use RCU-safe list
functions.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2012-10-17 11:02:10 +02:00
Johannes Berg 04ecd2578e mac80211: track needed RX chains for channel contexts
On each channel that the device is operating on, it
may need to listen using one or more chains depending
on the SMPS settings of the interfaces using it. The
previous channel context changes completely removed
this ability (before, it was available as the SMPS
mode).

Add per-context tracking of the required static and
dynamic RX chains and notify the driver on changes.
To achieve this, track the chains and SMPS mode used
on each virtual interface and update the channel
context whenever this changes.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2012-10-17 11:02:09 +02:00
Michal Kazior c3645eac47 mac80211: introduce new ieee80211_ops
Introduce channel context driver methods. The channel
on a context channel is immutable, but the channel type
and other properties can change.

Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2012-10-16 20:22:42 +02:00
Michal Kazior d01a1e6586 mac80211: introduce channel context skeleton code
Channel context are the foundation for multi-channel
operation. They are are immutable and are re-created
(or re-used if other interfaces are bound to a certain
channel and a compatible channel type) on channel
switching.

This is an initial implementation and more features
will come in separate patches.

Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
[some changes including RCU protection]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2012-10-16 20:22:41 +02:00
Johannes Berg e548c49e6d mac80211: add key flag for management keys
Mark keys that might be used to receive management
frames so drivers can fall back on software crypto
for them if they don't support hardware offload.
As the new flag is only set correctly for RX keys
and the existing IEEE80211_KEY_FLAG_SW_MGMT flag
can only affect TX, also rename the latter to
IEEE80211_KEY_FLAG_SW_MGMT_TX.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2012-09-10 11:29:17 +02:00
Johannes Berg 6d71117a27 mac80211: add IEEE80211_HW_P2P_DEV_ADDR_FOR_INTF
Some devices like the current iwlwifi implementation
require that the P2P interface address match the P2P
Device address (only one P2P interface is supported.)
Add the HW flag IEEE80211_HW_P2P_DEV_ADDR_FOR_INTF
that allows drivers to request that P2P Interfaces
added while a P2P Device is active get the same MAC
address by default.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2012-08-20 13:58:23 +02:00
Johannes Berg 4c29867790 mac80211: support A-MPDU status reporting
Support getting A-MPDU status information from the
drivers and reporting it to userspace via radiotap
in the standard fields.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2012-08-20 13:53:22 +02:00
Antonio Quartulli e687f61eed mac80211: add supported rates change notification in IBSS
In IBSS it is possible that the supported rates set for a station changes over
time (e.g. it gets first initialised as an empty set because of no available
information about rates and updated later). In this case the driver has to be
notified about the change in order to update its internal table accordingly (if
needed).

This behaviour is needed by all those drivers that handle rc internally but
leave stations management to mac80211

Reported-by: Gui Iribarren <gui@altermundi.net>
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
[Johannes - add docs, validate IBSS mode only, fix compilation]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2012-08-20 13:31:43 +02:00
Thomas Huehn 36323f817a mac80211: move TX station pointer and restructure TX
Remove the control.sta pointer from ieee80211_tx_info to free up
sufficient space in the TX skb control buffer for the upcoming
Transmit Power Control (TPC).
Instead, the pointer is now on the stack in a new control struct
that is passed as a function parameter to the drivers' tx method.

Signed-off-by: Thomas Huehn <thomas@net.t-labs.tu-berlin.de>
Signed-off-by: Alina Friedrichsen <x-alina@gmx.net>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
[reworded commit message]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2012-07-31 16:18:39 +02:00
Eliad Peller ab09587740 mac80211: add PS flag to bss_conf
Currently, ps mode is indicated per device (rather than
per interface), which doesn't make a lot of sense.

Moreover, there are subtle bugs caused by the inability
to indicate ps change along with other changes
(e.g. when the AP deauth us, we'd like to indicate
CHANGED_PS | CHANGED_ASSOC, as changing PS before
notifying about disassociation will result in null-packets
being sent (if IEEE80211_HW_SUPPORTS_DYNAMIC_PS) while
the sta is already disconnected.)

Keep the current per-device notifications, and add
parallel per-vif notifications.

In order to keep it simple, the per-device ps and
the per-vif ps are orthogonal - the per-vif ps
configuration is determined only by the user
configuration (enable/disable) and the connection
state, and is not affected by other vifs state and
(temporary) dynamic_ps/offchannel operations
(unlike per-device ps).

Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2012-07-31 16:11:04 +02:00
Johannes Berg 8c358bcd09 mac80211: add time synchronisation with BSS for assoc
Some drivers (iwlegacy, iwlwifi and rt2x00) today use the
bss_conf.last_tsf value. By itself though that value is
completely worthless since it may be ancient. What really
is needed is synchronisation between some device time and
the TSF.

To clarify this, rename bss_conf.last_tsf to sync_tsf and
add sync_device_ts which is obtained from rx_status which
gets a new field device_timestamp for this purpose. This
is intentionally not using the mactime field since that
is used for other things and in IBSS is expected to sync
with the IBSS's TSF which isn't necessarily true for the
device timestamp.

Also, since we have the information and it's useful even
before the connection has been established, give all the
timing details to the driver before authenticating.

Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2012-07-12 12:10:46 +02:00
Johannes Berg 30f422925c mac80211: optimize ieee80211_rx_status struct layout
We waste a lot of space in this struct because it uses
int values where smaller ones would be sufficient. The
upcoming A-MPDU information needs some space, optimize
the struct now.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2012-07-12 12:10:45 +02:00
Johannes Berg f72b85b8eb mac80211: remove ieee80211_key_removed
This API call was intended to be used by drivers
if they want to optimize key handling by removing
one key when another is added. Remove it since no
driver is using it. If needed, it can always be
added back.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2012-07-09 14:49:15 +02:00
Johannes Berg a1845fc7c5 mac80211: add TX prepare API
Some drivers require setup before being able to send
management frames in managed mode, in particular in
multi-channel cases.

Introduce API to allow the drivers to do such setup
while being able to sleep waiting for the setup to
finish in the device. This isn't possible inside the
TX call since that can't sleep.

A future patch may also restructure the TX retry to
wait for the driver to report the frame status, as
suggested by Arik in
http://mid.gmane.org/CA+XVXffKSEL6ZQPQ98x-zO-NL2=TNF1uN==mprRyUmAaRn254g@mail.gmail.com

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2012-07-03 13:50:34 +02:00
Thomas Huehn e3e1a0bcb3 mac80211: reduce IEEE80211_TX_MAX_RATES
IEEE80211_TX_MAX_RATES can be reduced from 5 to 4 as there
is no current hardware supporting a rate chain with 5 multi
rate stages (mrr), so 4 mrr stages are sufficient.

The memory that is freed within the ieee80211_tx_info struct
will be used in the upcoming Transmission Power Control (TPC)
implementation.

Suggested-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Thomas Huehn <thomas@net.t-labs.tu-berlin.de>
[reword commit message]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2012-07-03 13:48:37 +02:00
Johannes Berg cb831b537d mac80211: remove tx_frags driver callback
The implementation of tx_frags is buggy due to
not handling queue stop, and there's no driver
implementing it so remove it.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2012-07-02 15:40:18 +02:00
Johannes Berg b1fbd46976 Merge remote-tracking branch 'wireless-next/master' into mac80211-next 2012-06-28 13:45:58 +02:00
Johannes Berg fc8a7321d3 mac80211: don't expose ieee80211_add_srates_ie()
This and ieee80211_add_ext_srates_ie() aren't
exported, so can't be used by drivers anyway,
but there's also no reason that they should be
so make them private to mac80211 and use sdata
instead of vif arguments.

Acked-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2012-06-28 10:35:50 +02:00
John W. Linville 2c443443e7 Merge branch 'for-john' of git://git.sipsolutions.net/mac80211-next 2012-06-26 14:27:34 -04:00
Johannes Berg bdcbd8e0e3 mac80211: clean up debugging
There are a few things that make the logging and
debugging in mac80211 less useful than it should
be right now:
 * a lot of messages should be pr_info, not pr_debug
 * wholesale use of pr_debug makes it require *both*
   Kconfig and dynamic configuration
 * there are still a lot of ifdefs
 * the style is very inconsistent, sometimes the
   sdata->name is printed in front

Clean up everything, introducing new macros and
separating out the station MLME debugging into
a new Kconfig symbol.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2012-06-24 11:32:29 +02:00
Victor Goldenshtein 66572cfc30 mac80211: add command to get current rssi
Get current rssi (in dBm) from the driver/FW.

Instead of reporting the signal received in the last
rx packet, which might be inaccurate if rx traffic is
low and beacon filtering is enabled, get the signal
from the driver/FW.

Signed-off-by: Victor Goldenshtein <victorg@ti.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2012-06-21 16:42:17 +02:00
John W. Linville 211c17aaee Merge branch 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless
Conflicts:
	drivers/net/wireless/ath/ath9k/main.c
	net/bluetooth/hci_event.c
2012-06-13 15:35:35 -04:00
Johannes Berg d13e141481 mac80211: add some missing kernel-doc
Add a few kernel-doc descriptions that were missed
during development.

Reported-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2012-06-09 10:31:09 +02:00
Johannes Berg 2eb278e083 mac80211: unify SW/offload remain-on-channel
Redesign all the off-channel code, getting rid of
the generic off-channel work concept, replacing
it with a simple remain-on-channel list.

This fixes a number of small issues with the ROC
implementation:
 * offloaded remain-on-channel couldn't be queued,
   now we can queue it as well, if needed
 * in iwlwifi (the only user) offloaded ROC is
   mutually exclusive with scanning, use the new
   queue to handle that case -- I expect that it
   will later depend on a HW flag

The bigger issue though is that there's a bad bug
in the current implementation: if we get a mgmt
TX request while HW roc is active, and this new
request has a wait time, we actually schedule a
software ROC instead since we can't guarantee the
existing offloaded ROC will still be that long.
To fix this, the queuing mechanism was needed.

The queuing mechanism for offloaded ROC isn't yet
optimal, ideally we should add API to have the HW
extend the ROC if needed. We could add that later
but for now use a software implementation.

Overall, this unifies the behaviour between the
offloaded and software-implemented case as much
as possible.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-06-06 15:31:18 -04:00
Johannes Berg 196ac1c13d mac80211: do remain-on-channel while idle
The IDLE handling in HW off-channel is broken right
now since we turn off IDLE only when the off-channel
period already started. Therefore, all drivers that
use it today (only iwlwifi!) must support off-channel
while idle, so playing with idle isn't needed at all.

Off-channel in general, since it's no longer used for
authentication/association, shouldn't affect PS, so
also remove that logic.

Also document a small caveat for reporting TX status
from off-channel frames in HW remain-on-channel.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-06-06 15:20:33 -04:00
Eliad Peller 51ca9d8db2 mac80211: remove ieee80211_get_operstate()
ieee80211_get_operstate() was used by drivers in order to
know whether the sta link is up, but it's no longer needed
(nor used) as mac80211 notifies the drivers about
authorization changes (via the sta_state callback)

Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-06-05 15:32:10 -04:00
Joe Perches 499f42bb03 net: mac80211: Add and use ibss_vdbg debugging macro
Simplify the use of #ifdef CONFIG_MAC80211_IBSS_DEBUG/#endif
by adding a logging macro to encapsulate the test.

Convert the appropriate uses too.

Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-06-05 15:32:10 -04:00
Joe Perches d63e9ae3b1 net: mac80211: Add and use ht_vdbg debugging macro
Simplify the use of #ifdef CONFIG_MAC80211_HT_DEBUG/#endif
by adding a logging macro to encapsulate the test.

Convert the appropriate uses too.

Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-06-05 15:32:10 -04:00