Commit Graph

7631 Commits

Author SHA1 Message Date
David Sterba 53176dde0a btrfs: dev-replace: remove custom read/write blocking scheme
After the rw semaphore has been added, the custom blocking using
::blocking_readers and ::read_lock_wq is redundant.

The blocking logic in __btrfs_map_block is replaced by extending the
time the semaphore is held, that has the same blocking effect on writes
as the previous custom scheme that waited until ::blocking_readers was
zero.

Signed-off-by: David Sterba <dsterba@suse.com>
2018-12-17 14:51:45 +01:00
David Sterba 129827e300 btrfs: dev-replace: swich locking to rw semaphore
This is the first part of removing the custom locking and waiting scheme
used for device replace. It was probably copied from extent buffer
locking, but there's nothing that would require more than is provided by
the common locking primitives.

The rw spinlock protects waiting tasks counter in case of incompatible
locks and the waitqueue. Same as rw semaphore.

This patch only switches the locking primitive, for better
bisectability.  There should be no functional change other than the
overhead of the locking and potential sleeping instead of spinning when
the lock is contended.

Signed-off-by: David Sterba <dsterba@suse.com>
2018-12-17 14:51:44 +01:00
David Sterba ceb21a8db4 btrfs: reada: reorder dev-replace locks before radix tree preload
The device-replace read lock is going to use rw semaphore in followup
commits. The semaphore might sleep which is not possible in the radix
tree preload section. The lock nesting is now:

* device replace
  * radix tree preload
    * readahead spinlock

Signed-off-by: David Sterba <dsterba@suse.com>
2018-12-17 14:51:44 +01:00
Nikolay Borisov d1051d6ebf btrfs: Fix error handling in btrfs_cleanup_ordered_extents
Running btrfs/124 in a loop hung up on me sporadically with the
following call trace:

	btrfs           D    0  5760   5324 0x00000000
	Call Trace:
	 ? __schedule+0x243/0x800
	 schedule+0x33/0x90
	 btrfs_start_ordered_extent+0x10c/0x1b0 [btrfs]
	 ? wait_woken+0xa0/0xa0
	 btrfs_wait_ordered_range+0xbb/0x100 [btrfs]
	 btrfs_relocate_block_group+0x1ff/0x230 [btrfs]
	 btrfs_relocate_chunk+0x49/0x100 [btrfs]
	 btrfs_balance+0xbeb/0x1740 [btrfs]
	 btrfs_ioctl_balance+0x2ee/0x380 [btrfs]
	 btrfs_ioctl+0x1691/0x3110 [btrfs]
	 ? lockdep_hardirqs_on+0xed/0x180
	 ? __handle_mm_fault+0x8e7/0xfb0
	 ? _raw_spin_unlock+0x24/0x30
	 ? __handle_mm_fault+0x8e7/0xfb0
	 ? do_vfs_ioctl+0xa5/0x6e0
	 ? btrfs_ioctl_get_supported_features+0x30/0x30 [btrfs]
	 do_vfs_ioctl+0xa5/0x6e0
	 ? entry_SYSCALL_64_after_hwframe+0x3e/0xbe
	 ksys_ioctl+0x3a/0x70
	 __x64_sys_ioctl+0x16/0x20
	 do_syscall_64+0x60/0x1b0
	 entry_SYSCALL_64_after_hwframe+0x49/0xbe

This happens because during page writeback it's valid for
writepage_delalloc to instantiate a delalloc range which doesn't belong
to the page currently being written back.

The reason this case is valid is due to find_lock_delalloc_range
returning any available range after the passed delalloc_start and
ignoring whether the page under writeback is within that range.

In turn ordered extents (OE) are always created for the returned range
from find_lock_delalloc_range. If, however, a failure occurs while OE
are being created then the clean up code in btrfs_cleanup_ordered_extents
will be called.

Unfortunately the code in btrfs_cleanup_ordered_extents doesn't consider
the case of such 'foreign' range being processed and instead it always
assumes that the range OE are created for belongs to the page. This
leads to the first page of such foregin range to not be cleaned up since
it's deliberately missed and skipped by the current cleaning up code.

Fix this by correctly checking whether the current page belongs to the
range being instantiated and if so adjsut the range parameters passed
for cleaning up. If it doesn't, then just clean the whole OE range
directly.

Fixes: 524272607e ("btrfs: Handle delalloc error correctly to avoid ordered extent hang")
CC: stable@vger.kernel.org # 4.14+
Reviewed-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: Nikolay Borisov <nborisov@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
2018-12-17 14:51:44 +01:00
Lu Fengqi 3522e90301 btrfs: remove always true if branch in find_delalloc_range
The @found is always false when it comes to the if branch. Besides, the
bool type is more suitable for @found. Change the return value of the
function and its caller to bool as well.

Reviewed-by: Nikolay Borisov <nborisov@suse.com>
Signed-off-by: Lu Fengqi <lufq.fnst@cn.fujitsu.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
2018-12-17 14:51:44 +01:00
Lu Fengqi 27a7ff554e btrfs: skip file_extent generation check for free_space_inode in run_delalloc_nocow
The test case btrfs/001 with inode_cache mount option will encounter the
following warning:

  WARNING: CPU: 1 PID: 23700 at fs/btrfs/inode.c:956 cow_file_range.isra.19+0x32b/0x430 [btrfs]
  CPU: 1 PID: 23700 Comm: btrfs Kdump: loaded Tainted: G        W  O      4.20.0-rc4-custom+ #30
  Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 0.0.0 02/06/2015
  RIP: 0010:cow_file_range.isra.19+0x32b/0x430 [btrfs]
  Call Trace:
   ? free_extent_buffer+0x46/0x90 [btrfs]
   run_delalloc_nocow+0x455/0x900 [btrfs]
   btrfs_run_delalloc_range+0x1a7/0x360 [btrfs]
   writepage_delalloc+0xf9/0x150 [btrfs]
   __extent_writepage+0x125/0x3e0 [btrfs]
   extent_write_cache_pages+0x1b6/0x3e0 [btrfs]
   ? __wake_up_common_lock+0x63/0xc0
   extent_writepages+0x50/0x80 [btrfs]
   do_writepages+0x41/0xd0
   ? __filemap_fdatawrite_range+0x9e/0xf0
   __filemap_fdatawrite_range+0xbe/0xf0
   btrfs_fdatawrite_range+0x1b/0x50 [btrfs]
   __btrfs_write_out_cache+0x42c/0x480 [btrfs]
   btrfs_write_out_ino_cache+0x84/0xd0 [btrfs]
   btrfs_save_ino_cache+0x551/0x660 [btrfs]
   commit_fs_roots+0xc5/0x190 [btrfs]
   btrfs_commit_transaction+0x2bf/0x8d0 [btrfs]
   btrfs_mksubvol+0x48d/0x4d0 [btrfs]
   btrfs_ioctl_snap_create_transid+0x170/0x180 [btrfs]
   btrfs_ioctl_snap_create_v2+0x124/0x180 [btrfs]
   btrfs_ioctl+0x123f/0x3030 [btrfs]

The file extent generation of the free space inode is equal to the last
snapshot of the file root, so the inode will be passed to cow_file_rage.
But the inode was created and its extents were preallocated in
btrfs_save_ino_cache, there are no cow copies on disk.

The preallocated extent is not yet in the extent tree, and
btrfs_cross_ref_exist will ignore the -ENOENT returned by
check_committed_ref, so we can directly write the inode to the disk.

Fixes: 78d4295b1e ("btrfs: lift some btrfs_cross_ref_exist checks in nocow path")
CC: stable@vger.kernel.org # 4.18+
Reviewed-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: Lu Fengqi <lufq.fnst@cn.fujitsu.com>
Signed-off-by: David Sterba <dsterba@suse.com>
2018-12-17 14:51:44 +01:00
Filipe Manana 41bd606769 Btrfs: fix fsync of files with multiple hard links in new directories
The log tree has a long standing problem that when a file is fsync'ed we
only check for new ancestors, created in the current transaction, by
following only the hard link for which the fsync was issued. We follow the
ancestors using the VFS' dget_parent() API. This means that if we create a
new link for a file in a directory that is new (or in an any other new
ancestor directory) and then fsync the file using an old hard link, we end
up not logging the new ancestor, and on log replay that new hard link and
ancestor do not exist. In some cases, involving renames, the file will not
exist at all.

Example:

  mkfs.btrfs -f /dev/sdb
  mount /dev/sdb /mnt

  mkdir /mnt/A
  touch /mnt/foo
  ln /mnt/foo /mnt/A/bar
  xfs_io -c fsync /mnt/foo

  <power failure>

In this example after log replay only the hard link named 'foo' exists
and directory A does not exist, which is unexpected. In other major linux
filesystems, such as ext4, xfs and f2fs for example, both hard links exist
and so does directory A after mounting again the filesystem.

Checking if any new ancestors are new and need to be logged was added in
2009 by commit 12fcfd22fe ("Btrfs: tree logging unlink/rename fixes"),
however only for the ancestors of the hard link (dentry) for which the
fsync was issued, instead of checking for all ancestors for all of the
inode's hard links.

So fix this by tracking the id of the last transaction where a hard link
was created for an inode and then on fsync fallback to a full transaction
commit when an inode has more than one hard link and at least one new hard
link was created in the current transaction. This is the simplest solution
since this is not a common use case (adding frequently hard links for
which there's an ancestor created in the current transaction and then
fsync the file). In case it ever becomes a common use case, a solution
that consists of iterating the fs/subvol btree for each hard link and
check if any ancestor is new, could be implemented.

This solves many unexpected scenarios reported by Jayashree Mohan and
Vijay Chidambaram, and for which there is a new test case for fstests
under review.

Fixes: 12fcfd22fe ("Btrfs: tree logging unlink/rename fixes")
CC: stable@vger.kernel.org # 4.4+
Reported-by: Vijay Chidambaram <vvijay03@gmail.com>
Reported-by: Jayashree Mohan <jayashree2912@gmail.com>
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
2018-12-17 14:51:43 +01:00
David Sterba bbe339cc32 btrfs: drop extra enum initialization where using defaults
The first auto-assigned value to enum is 0, we can use that and not
initialize all members where the auto-increment does the same. This is
used for values that are not part of on-disk format.

Reviewed-by: Omar Sandoval <osandov@fb.com>
Reviewed-by: Qu Wenruo <wqu@suse.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: David Sterba <dsterba@suse.com>
2018-12-17 14:51:43 +01:00
David Sterba 5b840301ac btrfs: switch BTRFS_ORDERED_* to enums
We can use simple enum for values that are not part of on-disk format:
ordered extent flags.

Reviewed-by: Omar Sandoval <osandov@fb.com>
Reviewed-by: Qu Wenruo <wqu@suse.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: David Sterba <dsterba@suse.com>
2018-12-17 14:51:43 +01:00
David Sterba 50b5b6020f btrfs: switch EXTENT_FLAG_* to enums
We can use simple enum for values that are not part of on-disk format:
extent map flags.

Reviewed-by: Omar Sandoval <osandov@fb.com>
Reviewed-by: Qu Wenruo <wqu@suse.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: David Sterba <dsterba@suse.com>
2018-12-17 14:51:43 +01:00
David Sterba 80cb38362d btrfs: switch EXTENT_BUFFER_* to enums
We can use simple enum for values that are not part of on-disk format:
extent buffer flags;

Reviewed-by: Omar Sandoval <osandov@fb.com>
Reviewed-by: Qu Wenruo <wqu@suse.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: David Sterba <dsterba@suse.com>
2018-12-17 14:51:43 +01:00
David Sterba 61fa90c16b btrfs: switch BTRFS_ROOT_* to enums
We can use simple enum for values that are not part of on-disk format:
root tree flags.

Reviewed-by: Omar Sandoval <osandov@fb.com>
Reviewed-by: Qu Wenruo <wqu@suse.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: David Sterba <dsterba@suse.com>
2018-12-17 14:51:42 +01:00
David Sterba eb1a524c95 btrfs: switch BTRFS_FS_* to enums
We can use simple enum for values that are not part of on-disk format:
internal filesystem states.

Reviewed-by: Omar Sandoval <osandov@fb.com>
Reviewed-by: Qu Wenruo <wqu@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
2018-12-17 14:51:42 +01:00
David Sterba 688a75b9a3 btrfs: switch BTRFS_BLOCK_RSV_* to enums
We can use simple enum for values that are not part of on-disk format:
block reserve types.

Reviewed-by: Omar Sandoval <osandov@fb.com>
Reviewed-by: Qu Wenruo <wqu@suse.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: David Sterba <dsterba@suse.com>
2018-12-17 14:51:42 +01:00
David Sterba b00146b5d5 btrfs: switch BTRFS_FS_STATE_* to enums
We can use simple enum for values that are not part of on-disk format:
global filesystem states.

Reviewed-by: Omar Sandoval <osandov@fb.com>
Reviewed-by: Qu Wenruo <wqu@suse.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: David Sterba <dsterba@suse.com>
2018-12-17 14:51:42 +01:00
Nikolay Borisov da12fe5414 btrfs: Refactor btrfs_merge_bio_hook
This function really checks whether adding more data to the bio will
straddle a stripe/chunk. So first let's give it a more appropraite name
- btrfs_bio_fits_in_stripe. Secondly, the offset parameter was never
used to just remove it. Thirdly, pages are submitted to either btree or
data inodes so it's guaranteed that tree->ops is set so replace the
check with an ASSERT. Finally, document the parameters of the function.
No functional changes.

Signed-off-by: Nikolay Borisov <nborisov@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
2018-12-17 14:51:42 +01:00
Lu Fengqi 2ab4fd3135 btrfs: cleanup the useless DEFINE_WAIT in cleanup_transaction
When it was introduced in commit f094ac32ab ("Btrfs: fix NULL pointer
after aborting a transaction"), it was not used.

Signed-off-by: Lu Fengqi <lufq.fnst@cn.fujitsu.com>
Reviewed-by: Nikolay Borisov <nborisov@suse.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: David Sterba <dsterba@suse.com>
2018-12-17 14:51:42 +01:00
Johannes Thumshirn d2e174d5d3 btrfs: document extent mapping assumptions in checksum
Document why map_private_extent_buffer() cannot return '1' (i.e. the map
spans two pages) for the csum_tree_block() case.

The current algorithm for detecting a page boundary crossing in
map_private_extent_buffer() will return a '1' *IFF* the extent buffer's
offset in the page + the offset passed in by csum_tree_block() and the
minimal length passed in by csum_tree_block() - 1 are bigger than
PAGE_SIZE.

We always pass BTRFS_CSUM_SIZE (32) as offset and a minimal length of 32
and the current extent buffer allocator always guarantees page aligned
extends, so the above condition can't be true.

Reviewed-by: Nikolay Borisov <nborisov@suse.com>
Signed-off-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: David Sterba <dsterba@suse.com>
2018-12-17 14:51:41 +01:00
Johannes Thumshirn cc2c39d605 btrfs: don't initialize 'offset' in map_private_extent_buffer()
In map_private_extent_buffer() the 'offset' variable is initialized to a
page aligned version of the 'start' parameter.

But later on it is overwritten with either the offset from the extent
buffer's start or 0.

So get rid of the initial initialization.

Reviewed-by: Nikolay Borisov <nborisov@suse.com>
Signed-off-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: David Sterba <dsterba@suse.com>
2018-12-17 14:51:41 +01:00
Filipe Manana a5fb114291 Btrfs: fix deadlock with memory reclaim during scrub
When a transaction commit starts, it attempts to pause scrub and it blocks
until the scrub is paused. So while the transaction is blocked waiting for
scrub to pause, we can not do memory allocation with GFP_KERNEL from scrub,
otherwise we risk getting into a deadlock with reclaim.

Checking for scrub pause requests is done early at the beginning of the
while loop of scrub_stripe() and later in the loop, scrub_extent() and
scrub_raid56_parity() are called, which in turn call scrub_pages() and
scrub_pages_for_parity() respectively. These last two functions do memory
allocations using GFP_KERNEL. Same problem could happen while scrubbing
the super blocks, since it calls scrub_pages().

We also can not have any of the worker tasks, created by the scrub task,
doing GFP_KERNEL allocations, because before pausing, the scrub task waits
for all the worker tasks to complete (also done at scrub_stripe()).

So make sure GFP_NOFS is used for the memory allocations because at any
time a scrub pause request can happen from another task that started to
commit a transaction.

Fixes: 58c4e17384 ("btrfs: scrub: use GFP_KERNEL on the submission path")
CC: stable@vger.kernel.org # 4.6+
Reviewed-by: Nikolay Borisov <nborisov@suse.com>
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
2018-12-17 14:51:41 +01:00
Nikolay Borisov 78e62c02ab btrfs: Remove extent_io_ops::readpage_io_failed_hook
For data inodes this hook does nothing but to return -EAGAIN which is
used to signal to the endio routines that this bio belongs to a data
inode. If this is the case the actual retrying is handled by
bio_readpage_error. Alternatively, if this bio belongs to the btree
inode then btree_io_failed_hook just does some cleanup and doesn't retry
anything.

This patch simplifies the code flow by eliminating
readpage_io_failed_hook and instead open-coding btree_io_failed_hook in
end_bio_extent_readpage. Also eliminate some needless checks since IO is
always performed on either data inode or btree inode, both of which are
guaranteed to have their extent_io_tree::ops set.

Signed-off-by: Nikolay Borisov <nborisov@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
2018-12-17 14:51:41 +01:00
Johannes Thumshirn 7b41ba71c1 btrfs: remove btrfs_bio_end_io_t
The btrfs_bio_end_io_t typedef was introduced with commit
a1d3c4786a ("btrfs: btrfs_multi_bio replaced with btrfs_bio")
but never used anywhere. This commit also introduced a forward declaration
of 'struct btrfs_bio' which is only needed for btrfs_bio_end_io_t.

Remove both as they're not needed anywhere.

Reviewed-by: Nikolay Borisov <nborisov@suse.com>
Signed-off-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: David Sterba <dsterba@suse.com>
2018-12-17 14:51:40 +01:00
David Sterba b3a0dd50c3 btrfs: replace btrfs_io_bio::end_io with a simple helper
The end_io callback implemented as btrfs_io_bio_endio_readpage only
calls kfree. Also the callback is set only in case the csum buffer is
allocated and not pointing to the inline buffer. We can use that
information to drop the indirection and call a helper that will free the
csums only in the right case.

This shrinks struct btrfs_io_bio by 8 bytes.

Reviewed-by: Nikolay Borisov <nborisov@suse.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: David Sterba <dsterba@suse.com>
2018-12-17 14:51:40 +01:00
David Sterba 31fecccbd7 btrfs: remove redundant csum buffer in btrfs_io_bio
The io_bio tracks checksums and has an inline buffer or an allocated
one. And there's a third member that points to the right one, but we
don't need to use an extra pointer for that. Let btrfs_io_bio::csum
point to the right buffer and check that the inline buffer is not
accidentally freed.

This shrinks struct btrfs_io_bio by 8 bytes.

Reviewed-by: Nikolay Borisov <nborisov@suse.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: David Sterba <dsterba@suse.com>
2018-12-17 14:51:40 +01:00
David Sterba 600b6cf468 btrfs: replace async_cow::root with fs_info
The async_cow::root is used to propagate fs_info to async_cow_submit.
We can't use inode to reach it because it could become NULL after
write without compression in async_cow_start.

Reviewed-by: Nikolay Borisov <nborisov@suse.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: David Sterba <dsterba@suse.com>
2018-12-17 14:51:40 +01:00
David Sterba 06ea01b1ee btrfs: merge btrfs_submit_bio_done to its caller
There's one caller and its code is simple, we can open code it in
run_one_async_done. The errors are passed through bio.

Reviewed-by: Nikolay Borisov <nborisov@suse.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: David Sterba <dsterba@suse.com>
2018-12-17 14:51:40 +01:00
Anand Jain 7333bd02dc btrfs: balance: print to system log when balance ends or is paused
Print a kernel log message when the balance ends, either for cancel or
completed or if it is paused.

Signed-off-by: Anand Jain <anand.jain@oracle.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
2018-12-17 14:51:39 +01:00
Anand Jain 56fc37d936 btrfs: balance: print args during start and resume
The information about balance arguments is important for system audit,
this patch prints the textual representation when balance starts or is
resumed.

Example command:

 $ btrfs balance start -f -mprofiles=raid1,convert=single,soft -dlimit=10..20,usage=50 /btrfs

Example kernel log output:

 BTRFS info (device sdb): balance: start -f -dusage=50,limit=10..20 -mconvert=single,soft,profiles=raid1 -sconvert=single,soft,profiles=raid1

Signed-off-by: Anand Jain <anand.jain@oracle.com>
Reviewed-by: David Sterba <dsterba@suse.com>
[ update changelog, simplify code ]
Signed-off-by: David Sterba <dsterba@suse.com>
2018-12-17 14:51:39 +01:00
Anand Jain f89e09cf45 btrfs: add helper to describe block group flags
Factor out helper that describes block group flags from
describe_relocation. The result will not be longer than the given size.

Signed-off-by: Anand Jain <anand.jain@oracle.com>
Reviewed-by: David Sterba <dsterba@suse.com>
[ add comments ]
Signed-off-by: David Sterba <dsterba@suse.com>
2018-12-17 14:51:39 +01:00
Filipe Manana 9a6f209e36 Btrfs: fix deadlock when enabling quotas due to concurrent snapshot creation
If the quota enable and snapshot creation ioctls are called concurrently
we can get into a deadlock where the task enabling quotas will deadlock
on the fs_info->qgroup_ioctl_lock mutex because it attempts to lock it
twice, or the task creating a snapshot tries to commit the transaction
while the task enabling quota waits for the former task to commit the
transaction while holding the mutex. The following time diagrams show how
both cases happen.

First scenario:

           CPU 0                                    CPU 1

 btrfs_ioctl()
  btrfs_ioctl_quota_ctl()
   btrfs_quota_enable()
    mutex_lock(fs_info->qgroup_ioctl_lock)
    btrfs_start_transaction()

                                             btrfs_ioctl()
                                              btrfs_ioctl_snap_create_v2
                                               create_snapshot()
                                                --> adds snapshot to the
                                                    list pending_snapshots
                                                    of the current
                                                    transaction

    btrfs_commit_transaction()
     create_pending_snapshots()
       create_pending_snapshot()
        qgroup_account_snapshot()
         btrfs_qgroup_inherit()
	   mutex_lock(fs_info->qgroup_ioctl_lock)
	    --> deadlock, mutex already locked
	        by this task at
		btrfs_quota_enable()

Second scenario:

           CPU 0                                    CPU 1

 btrfs_ioctl()
  btrfs_ioctl_quota_ctl()
   btrfs_quota_enable()
    mutex_lock(fs_info->qgroup_ioctl_lock)
    btrfs_start_transaction()

                                             btrfs_ioctl()
                                              btrfs_ioctl_snap_create_v2
                                               create_snapshot()
                                                --> adds snapshot to the
                                                    list pending_snapshots
                                                    of the current
                                                    transaction

                                                btrfs_commit_transaction()
                                                 --> waits for task at
                                                     CPU 0 to release
                                                     its transaction
                                                     handle

    btrfs_commit_transaction()
     --> sees another task started
         the transaction commit first
     --> releases its transaction
         handle
     --> waits for the transaction
         commit to be completed by
         the task at CPU 1

                                                 create_pending_snapshot()
                                                  qgroup_account_snapshot()
                                                   btrfs_qgroup_inherit()
                                                    mutex_lock(fs_info->qgroup_ioctl_lock)
                                                     --> deadlock, task at CPU 0
                                                         has the mutex locked but
                                                         it is waiting for us to
                                                         finish the transaction
                                                         commit

So fix this by setting the quota enabled flag in fs_info after committing
the transaction at btrfs_quota_enable(). This ends up serializing quota
enable and snapshot creation as if the snapshot creation happened just
before the quota enable request. The quota rescan task, scheduled after
committing the transaction in btrfs_quote_enable(), will do the accounting.

Fixes: 6426c7ad69 ("btrfs: qgroup: Fix qgroup accounting when creating snapshot")
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
2018-12-17 14:51:39 +01:00
Filipe Manana 5a8067c0d1 Btrfs: fix access to available allocation bits when starting balance
The available allocation bits members from struct btrfs_fs_info are
protected by a sequence lock, and when starting balance we access them
incorrectly in two different ways:

1) In the read sequence lock loop at btrfs_balance() we use the values we
   read from fs_info->avail_*_alloc_bits and we can immediately do actions
   that have side effects and can not be undone (printing a message and
   jumping to a label). This is wrong because a retry might be needed, so
   our actions must not have side effects and must be repeatable as long
   as read_seqretry() returns a non-zero value. In other words, we were
   essentially ignoring the sequence lock;

2) Right below the read sequence lock loop, we were reading the values
   from avail_metadata_alloc_bits and avail_data_alloc_bits without any
   protection from concurrent writers, that is, reading them outside of
   the read sequence lock critical section.

So fix this by making sure we only read the available allocation bits
while in a read sequence lock critical section and that what we do in the
critical section is repeatable (has nothing that can not be undone) so
that any eventual retry that is needed is handled properly.

Fixes: de98ced9e7 ("Btrfs: use seqlock to protect fs_info->avail_{data, metadata, system}_alloc_bits")
Fixes: 1450612797 ("btrfs: fix a bogus warning when converting only data or metadata")
Reviewed-by: Nikolay Borisov <nborisov@suse.com>
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
2018-12-17 14:51:39 +01:00
Filipe Manana 0e6ec385b5 Btrfs: allow clear_extent_dirty() to receive a cached extent state record
We can have a lot freed extents during the life span of transaction, so
the red black tree that keeps track of the ranges of each freed extent
(fs_info->freed_extents[]) can get quite big. When finishing a
transaction commit we find each range, process it (discard the extents,
unpin them) and then remove it from the red black tree.

We can use an extent state record as a cache when searching for a range,
so that when we clean the range we can use the cached extent state we
passed to the search function instead of iterating the red black tree
again. Doing things as fast as possible when finishing a transaction (in
state TRANS_STATE_UNBLOCKED) is convenient as it reduces the time we
block another task that wants to commit the next transaction.

So change clear_extent_dirty() to allow an optional extent state record to
be passed as an argument, which will be passed down to __clear_extent_bit.

Reviewed-by: Nikolay Borisov <nborisov@suse.com>
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
2018-12-17 14:51:38 +01:00
Nikolay Borisov cc5de4e702 btrfs: Handle final split-brain possibility during fsid change
This patch lands the last case which needs to be handled by the fsid
change code. Namely, this is the case where a multidisk filesystem has
already undergone at least one successful fsid change i.e all disks
have the METADATA_UUID incompat bit and power failure occurs as another
fsid change is in progress. When such an event occurs, disks could be
split in 2 groups. One of the groups will have both METADATA_UUID and
CHANGING_FSID_V2 flags set coupled with old fsid/metadata_uuid pairs.
The other group of disks will have only METADATA_UUID bit set and their
fsid will be different than the one in disks in the first group. Here
we look at the following cases:

  a) A disk from the first group is scanned first, so fs_devices is
  created with stale fsid/metdata_uuid. Then when a disk from the
  second group is scanned it needs to first check whether there exists
  such an fs_devices that has fsid_change set to true (because it was
  created with a disk having the CHANGING_FSID_V2 flag), the
  metadata_uuid and fsid of the fs_devices will be different (since it was
  created by a disk which already has had at least 1 successful fsid change)
  and finally the metadata_uuid of the fs_devices will equal that of the
  currently scanned disk (because metadata_uuid never really changes).
  When the correct fs_devices is found the information from the scanned
  disk will replace the current one in fs_devices since the scanned disk
  will have higher generation number.

  b) A disk from the second group is scanned so fs_devices is created
  as usual with differing fsid/metdata_uid. Then when a disk from the
  first group is scanned the code detects that it has both
  CHANGING_FSID_V2 and METADATA_UUID flags set and will search for
  fs_devices that has differing metadata_uuid/fsid and whose
  metadata_uuid is the same as that of the scanned device.

Signed-off-by: Nikolay Borisov <nborisov@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
2018-12-17 14:51:38 +01:00
Nikolay Borisov 7a62d0f073 btrfs: Handle one more split-brain scenario during fsid change
This commit continues hardening the scanning code to handle cases where
power loss could have caused disks in a multi-disk filesystem to be
in inconsistent state. Namely handle the situation that can occur when
some of the disks in multi-disk fs have completed their fsid change i.e
they have METADATA_UUID incompat flag set, have cleared the
CHANGING_FSID_V2 flag and their fsid/metadata_uuid are different. At
the same time the other half of the disks will have their
fsid/metadata_uuid unchanged and will only have CHANGING_FSID_V2 flag.

This is handled by introducing code in the scan path which:

 a) Handles the case when a device with CHANGING_FSID_V2 flag is
 scanned and as a result btrfs_fs_devices is created with matching
 fsid/metdata_uuid. Subsequently, when a device with completed fsid
 change is scanned it will detect this via the new code in find_fsid
 i.e that such an fs_devices exist that fsid_change flag is set to true,
 it's metadata_uuid/fsid match and the metadata_uuid of the scanned
 device matches that of the fs_devices. In this case, it's important to
 note that the devices which has its fsid change completed will have a
 higher generation number than the device with FSID_CHANGING_V2 flag
 set, so its superblock block will be used during mount. To prevent an
 assertion triggering because the sb used for mounting will have
 differing fsid/metadata_uuid than the ones in the fs_devices struct
 also add code in device_list_add which overwrites the values in
 fs_devices.

 b) Alternatively we can end up with a device that completed its
 fsid change be scanned first which will create the respective
 btrfs_fs_devices struct with differing fsid/metadata_uuid. In this
 case when a device with FSID_CHANGING_V2 flag set is scanned it will
 call the newly added find_fsid_inprogress function which will return
 the correct fs_devices.

Signed-off-by: Nikolay Borisov <nborisov@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
2018-12-17 14:51:38 +01:00
Nikolay Borisov d1a6300282 btrfs: add members to fs_devices to track fsid changes
In order to gracefully handle split-brain scenario during fsid change
(which are very unlikely, yet possible), two more pieces of information
will be necessary:

1. The highest generation number among all devices registered to a
   particular btrfs_fs_devices

2. A boolean flag whether a given btrfs_fs_devices was created by a
   device which had the FSID_CHANGING_V2 flag set.

This is a preparatory patch and just introduces the variables as well
as code which sets them, their actual use is going to happen in a later
patch.

Signed-off-by: Nikolay Borisov <nborisov@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
2018-12-17 14:51:38 +01:00
Nikolay Borisov fbc6feaec9 btrfs: Add handling for disk split-brain scenario during fsid change
Even though fsid change without rewrite is a very quick operation it's
still possible to experience a split-brain scenario if power loss occurs
at the most inconvenient time. This patch handles the case where power
failure occurs while the first transaction (the one setting
CHANGING_FSID_V2) flag is being persisted on disk. This can cause the
btrfs_fs_devices of this filesystem to be created by a device which:

 a) has the CHANGING_FSID_V2 flag set but its fsid value is intact

 b) or a device which doesn't have CHANGING_FSID_V2 flag set and its
    fsid value is intact

This situation is trivially handled by the current find_fsid code since
in both cases the devices are going to be treated like ordinary devices.
Since btrfs is always mounted using the superblock of the latest
device (the one with highest generation number), meaning it will have
the CHANGING_FSID_V2 flag set, ensure it's being cleared on mount. On
the first transaction commit following mount all disks will have it
cleared.

Signed-off-by: Nikolay Borisov <nborisov@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
2018-12-17 14:51:38 +01:00
Nikolay Borisov de37aa5131 btrfs: Remove fsid/metadata_fsid fields from btrfs_info
Currently btrfs_fs_info structure contains a copy of the
fsid/metadata_uuid fields. Same values are also contained in the
btrfs_fs_devices structure which fs_info has a reference to. Let's
reduce duplication by removing the fields from fs_info and always refer
to the ones in fs_devices. No functional changes.

Signed-off-by: Nikolay Borisov <nborisov@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
2018-12-17 14:51:37 +01:00
Nikolay Borisov 56f20f4009 btrfs: Add sysfs support for metadata_uuid feature
Since the metadata_uuid is a new incompat feature it requires the
respective sysfs hooks. This patch adds the 'metdata_uuid' feature to
be shown if it supported by the kernel. Additionally it adds
/sys/fs/btrfs/UUID/metadata_uuid attribute which allows one to read
the current metadata_uuid.

Signed-off-by: Nikolay Borisov <nborisov@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
2018-12-17 14:51:37 +01:00
Nikolay Borisov 7239ff4b2b btrfs: Introduce support for FSID change without metadata rewrite
This field is going to be used when the user wants to change the UUID
of the filesystem without having to rewrite all metadata blocks. This
field adds another level of indirection such that when the FSID is
changed what really happens is the current UUID (the one with which the
fs was created) is copied to the 'metadata_uuid' field in the superblock
as well as a new incompat flag is set METADATA_UUID. When the kernel
detects this flag is set it knows that the superblock in fact has 2
UUIDs:

1. Is the UUID which is user-visible, currently known as FSID.
2. Metadata UUID - this is the UUID which is stamped into all on-disk
   datastructures belonging to this file system.

When the new incompat flag is present device scanning checks whether
both fsid/metadata_uuid of the scanned device match any of the
registered filesystems. When the flag is not set then both UUIDs are
equal and only the FSID is retained on disk, metadata_uuid is set only
in-memory during mount.

Additionally a new metadata_uuid field is also added to the fs_info
struct. It's initialised either with the FSID in case METADATA_UUID
incompat flag is not set or with the metdata_uuid of the superblock
otherwise.

This commit introduces the new fields as well as the new incompat flag
and switches all users of the fsid to the new logic.

Signed-off-by: Nikolay Borisov <nborisov@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
[ minor updates in comments ]
Signed-off-by: David Sterba <dsterba@suse.com>
2018-12-17 14:51:37 +01:00
Johannes Thumshirn ce9f967f31 btrfs: use EXPORT_FOR_TESTS for conditionally exported functions
Several functions in BTRFS are only used inside the source file they are
declared if CONFIG_BTRFS_FS_RUN_SANITY_TESTS is not defined. However if
CONFIG_BTRFS_FS_RUN_SANITY_TESTS is defined these functions are shared
with the unit tests code.

Before the introduction of the EXPORT_FOR_TESTS macro, these functions
could not be declared as static and the compiler had a harder task when
optimizing and inlining them.

As we have EXPORT_FOR_TESTS now, use it where appropriate to support the
compiler.

Reviewed-by: Nikolay Borisov <nborisov@suse.com>
Signed-off-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
2018-12-17 14:51:37 +01:00
Johannes Thumshirn f8f591df7d btrfs: introduce EXPORT_FOR_TESTS macro
Depending on whether CONFIG_BTRFS_FS_RUN_SANITY_TESTS is set, some BTRFS
functions are either local to the file they are implemented in and thus
should be declared static or are called from within the test
implementation defined in a different file.

Introduce an EXPORT_FOR_TESTS macro which depending on
CONFIG_BTRFS_FS_RUN_SANITY_TESTS either adds the 'static' keyword to a
function or not.

Reviewed-by: Nikolay Borisov <nborisov@suse.com>
Signed-off-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: David Sterba <dsterba@suse.com>
2018-12-17 14:51:37 +01:00
Johannes Thumshirn e9a05cf31b btrfs: remove unused drop_on_err in btrfs_mkdir
Up to commit 32955c5422 ("btrfs: switch to discard_new_inode()") the
drop_on_err variable in btrfs_mkdir() was used to check whether the
inode had to be dropped via iput().

After commit 32955c5422 ("btrfs: switch to discard_new_inode()")
discard_new_inode() is called when err is set and inode is non NULL.
Therefore drop_on_err is not used anymore and thus causes a warning when
building with -Wunused-but-set-variable.

Reviewed-by: Omar Sandoval <osandov@fb.com>
Reviewed-by: Nikolay Borisov <nborisov@suse.com>
Reviewed-by: Qu Wenruo <wqu@suse.com>
Signed-off-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: David Sterba <dsterba@suse.com>
2018-12-17 14:51:36 +01:00
Nikolay Borisov 9bfd61d975 btrfs: Replace BUG_ON with ASSERT in find_lock_delalloc_range
lock_delalloc_pages should only return 2 values - 0 in case of success
and -EAGAIN if the range of pages to be locked should be shrunk due to
some of gone. Manual inspections confirms that this is indeed the case
since __process_pages_contig is where lock_delalloc_pages gets its
return value. The latter always returns 0  or -EAGAIN so the invariant
holds. No functional changes.

Reviewed-by: Qu Wenruo <wqu@suse.com>
Reviewed-by: Anand Jain <anand.jain@oracle.com>
Signed-off-by: Nikolay Borisov <nborisov@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
2018-12-17 14:51:36 +01:00
Nikolay Borisov 917aacecc5 btrfs: Sink find_lock_delalloc_range's 'max_bytes' argument
All callers of this function pass BTRFS_MAX_EXTENT_SIZE (128M) so let's
reduce the argument count and make that a local variable. No functional
changes.

Reviewed-by: Qu Wenruo <wqu@suse.com>
Reviewed-by: Anand Jain <anand.jain@oracle.com>
Signed-off-by: Nikolay Borisov <nborisov@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
2018-12-17 14:51:36 +01:00
Nikolay Borisov 64bc6c2a34 btrfs: Remove superfluous check form btrfs_remove_chunk
It's unnecessary to check map->stripes[i].dev for NULL given its value
is already set and dereferenced above the the check. No functional
changes.

Reviewed-by: Qu Wenruo <wqu@suse.com>
Reviewed-by: Anand Jain <anand.jain@oracle.com>
Signed-off-by: Nikolay Borisov <nborisov@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
2018-12-17 14:51:36 +01:00
Anand Jain f9085abfae btrfs: don't report user-requested cancel as an error
As of now only user requested replace cancel can cancel the
replace-scrub so no need to log the error.

Signed-off-by: Anand Jain <anand.jain@oracle.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
2018-12-17 14:51:36 +01:00
Anand Jain 49365e6976 btrfs: silence warning if replace is canceled
When we successfully cancel the device replace, its scrub worker returns
-ECANCELED, which is then passed to btrfs_dev_replace_finishing.

It cleans up based on the returned status and propagates the same
-ECANCELED back the parent function. As of now only user can cancel the
replace-scrub, so its ok to silence the warning here.

Signed-off-by: Anand Jain <anand.jain@oracle.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
2018-12-17 14:51:35 +01:00
Anand Jain 53e62fb5a4 btrfs: dev-replace: add explicit check for replace result "no error"
We recast the replace return status
BTRFS_IOCTL_DEV_REPLACE_RESULT_SCRUB_INPROGRESS to 0, to indicate no
error.
And since BTRFS_IOCTL_DEV_REPLACE_RESULT_NO_ERROR should also return 0,
which is also declared as 0, so we just return. Instead add it to the if
statement so that there is enough clarity while reading the code.

Signed-off-by: Anand Jain <anand.jain@oracle.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
2018-12-17 14:51:35 +01:00
Anand Jain fe97e2e173 btrfs: dev-replace: replace's scrub must not be running in suspended state
When the replace state is in the suspended state, btrfs_scrub_cancel()
should fail with -ENOTCONN as there is no scrub running. As a safety
catch check if btrfs_scrub_cancel() returns -ENOTCONN and assert if it
doesn't.

Signed-off-by: Anand Jain <anand.jain@oracle.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
2018-12-17 14:51:35 +01:00
Anand Jain b47dda2ef6 btrfs: dev-replace: set result code of cancel by status of scrub
The device-replace needs to check the result code of the scrub workers
in btrfs_dev_replace_cancel and distinguish if successful cancel
operation and when the there was no operation running.

If btrfs_scrub_cancel() fails, return
BTRFS_IOCTL_DEV_REPLACE_RESULT_NOT_STARTED so that user can try
to cancel the replace again.

Signed-off-by: Anand Jain <anand.jain@oracle.com>
Reviewed-by: David Sterba <dsterba@suse.com>
[ update changelog ]
Signed-off-by: David Sterba <dsterba@suse.com>
2018-12-17 14:51:35 +01:00
Anand Jain d189dd70e2 btrfs: fix use-after-free due to race between replace start and cancel
The device replace cancel thread can race with the replace start thread
and if fs_info::scrubs_running is not yet set, btrfs_scrub_cancel() will
fail to stop the scrub thread.

The scrub thread continues with the scrub for replace which then will
try to write to the target device and which is already freed by the
cancel thread.

scrub_setup_ctx() warns as tgtdev is NULL.

  struct scrub_ctx *scrub_setup_ctx(struct btrfs_device *dev, int is_dev_replace)
  {
  ...
	  if (is_dev_replace) {
		  WARN_ON(!fs_info->dev_replace.tgtdev);  <===
		  sctx->pages_per_wr_bio = SCRUB_PAGES_PER_WR_BIO;
		  sctx->wr_tgtdev = fs_info->dev_replace.tgtdev;
		  sctx->flush_all_writes = false;
	  }

  [ 6724.497655] BTRFS info (device sdb): dev_replace from /dev/sdb (devid 1) to /dev/sdc started
  [ 6753.945017] BTRFS info (device sdb): dev_replace from /dev/sdb (devid 1) to /dev/sdc canceled
  [ 6852.426700] WARNING: CPU: 0 PID: 4494 at fs/btrfs/scrub.c:622 scrub_setup_ctx.isra.19+0x220/0x230 [btrfs]
  ...
  [ 6852.428928] RIP: 0010:scrub_setup_ctx.isra.19+0x220/0x230 [btrfs]
  ...
  [ 6852.432970] Call Trace:
  [ 6852.433202]  btrfs_scrub_dev+0x19b/0x5c0 [btrfs]
  [ 6852.433471]  btrfs_dev_replace_start+0x48c/0x6a0 [btrfs]
  [ 6852.433800]  btrfs_dev_replace_by_ioctl+0x3a/0x60 [btrfs]
  [ 6852.434097]  btrfs_ioctl+0x2476/0x2d20 [btrfs]
  [ 6852.434365]  ? do_sigaction+0x7d/0x1e0
  [ 6852.434623]  do_vfs_ioctl+0xa9/0x6c0
  [ 6852.434865]  ? syscall_trace_enter+0x1c8/0x310
  [ 6852.435124]  ? syscall_trace_enter+0x1c8/0x310
  [ 6852.435387]  ksys_ioctl+0x60/0x90
  [ 6852.435663]  __x64_sys_ioctl+0x16/0x20
  [ 6852.435907]  do_syscall_64+0x50/0x180
  [ 6852.436150]  entry_SYSCALL_64_after_hwframe+0x49/0xbe

Further, as the replace thread enters scrub_write_page_to_dev_replace()
without the target device it panics:

  static int scrub_add_page_to_wr_bio(struct scrub_ctx *sctx,
				      struct scrub_page *spage)
  {
  ...
	bio_set_dev(bio, sbio->dev->bdev); <======

  [ 6929.715145] BUG: unable to handle kernel NULL pointer dereference at 00000000000000a0
  ..
  [ 6929.717106] Workqueue: btrfs-scrub btrfs_scrub_helper [btrfs]
  [ 6929.717420] RIP: 0010:scrub_write_page_to_dev_replace+0xb4/0x260
  [btrfs]
  ..
  [ 6929.721430] Call Trace:
  [ 6929.721663]  scrub_write_block_to_dev_replace+0x3f/0x60 [btrfs]
  [ 6929.721975]  scrub_bio_end_io_worker+0x1af/0x490 [btrfs]
  [ 6929.722277]  normal_work_helper+0xf0/0x4c0 [btrfs]
  [ 6929.722552]  process_one_work+0x1f4/0x520
  [ 6929.722805]  ? process_one_work+0x16e/0x520
  [ 6929.723063]  worker_thread+0x46/0x3d0
  [ 6929.723313]  kthread+0xf8/0x130
  [ 6929.723544]  ? process_one_work+0x520/0x520
  [ 6929.723800]  ? kthread_delayed_work_timer_fn+0x80/0x80
  [ 6929.724081]  ret_from_fork+0x3a/0x50

Fix this by letting the btrfs_dev_replace_finishing() to do the job of
cleaning after the cancel, including freeing of the target device.
btrfs_dev_replace_finishing() is called when btrfs_scub_dev() returns
along with the scrub return status.

Signed-off-by: Anand Jain <anand.jain@oracle.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
2018-12-17 14:51:35 +01:00
Anand Jain 05c49e6bc1 btrfs: dev-replace: go back to suspend state if another EXCL_OP is running
In a secnario where balance and replace co-exists as below,

  - start balance
  - pause balance
  - start replace
  - reboot

and when system restarts, balance resumes first. Then the replace is
attempted to restart but will fail as the EXCL_OP lock is already held
by the balance. If so place the replace state back to
BTRFS_IOCTL_DEV_REPLACE_STATE_SUSPENDED state.

Fixes: 010a47bde9 ("btrfs: add proper safety check before resuming dev-replace")
CC: stable@vger.kernel.org # 4.18+
Signed-off-by: Anand Jain <anand.jain@oracle.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
2018-12-17 14:51:34 +01:00
Anand Jain 0d228ece59 btrfs: dev-replace: go back to suspended state if target device is missing
At the time of forced unmount we place the running replace to
BTRFS_IOCTL_DEV_REPLACE_STATE_SUSPENDED state, so when the system comes
back and expect the target device is missing.

Then let the replace state continue to be in
BTRFS_IOCTL_DEV_REPLACE_STATE_SUSPENDED state instead of
BTRFS_IOCTL_DEV_REPLACE_STATE_STARTED as there isn't any matching scrub
running as part of replace.

Fixes: e93c89c1aa ("Btrfs: add new sources for device replace code")
CC: stable@vger.kernel.org # 4.4+
Signed-off-by: Anand Jain <anand.jain@oracle.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
2018-12-17 14:51:34 +01:00
Anand Jain 54862d6d28 btrfs: mark btrfs_dev_replace_start as static
There isn't any other consumer other than in its own file dev-replace.c.

Signed-off-by: Anand Jain <anand.jain@oracle.com>
Reviewed-by: Nikolay Borisov <nborisov@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
2018-12-17 14:51:34 +01:00
Anand Jain a9261d4125 btrfs: harden agaist duplicate fsid on scanned devices
It's not that impossible to imagine that a device OR a btrfs image is
copied just by using the dd or the cp command. Which in case both the
copies of the btrfs will have the same fsid. If on the system with
automount enabled, the copied FS gets scanned.

We have a known bug in btrfs, that we let the device path be changed
after the device has been mounted. So using this loop hole the new
copied device would appears as if its mounted immediately after it's
been copied.

For example:

Initially.. /dev/mmcblk0p4 is mounted as /

  $ lsblk
  NAME        MAJ:MIN RM  SIZE RO TYPE MOUNTPOINT
  mmcblk0     179:0    0 29.2G  0 disk
  |-mmcblk0p4 179:4    0    4G  0 part /
  |-mmcblk0p2 179:2    0  500M  0 part /boot
  |-mmcblk0p3 179:3    0  256M  0 part [SWAP]
  `-mmcblk0p1 179:1    0  256M  0 part /boot/efi

  $ btrfs fi show
     Label: none  uuid: 07892354-ddaa-4443-90ea-f76a06accaba
     Total devices 1 FS bytes used 1.40GiB
     devid    1 size 4.00GiB used 3.00GiB path /dev/mmcblk0p4

Copy mmcblk0 to sda

  $ dd if=/dev/mmcblk0 of=/dev/sda

And immediately after the copy completes the change in the device
superblock is notified which the automount scans using btrfs device scan
and the new device sda becomes the mounted root device.

  $ lsblk
  NAME        MAJ:MIN RM  SIZE RO TYPE MOUNTPOINT
  sda           8:0    1 14.9G  0 disk
  |-sda4        8:4    1    4G  0 part /
  |-sda2        8:2    1  500M  0 part
  |-sda3        8:3    1  256M  0 part
  `-sda1        8:1    1  256M  0 part
  mmcblk0     179:0    0 29.2G  0 disk
  |-mmcblk0p4 179:4    0    4G  0 part
  |-mmcblk0p2 179:2    0  500M  0 part /boot
  |-mmcblk0p3 179:3    0  256M  0 part [SWAP]
  `-mmcblk0p1 179:1    0  256M  0 part /boot/efi

  $ btrfs fi show /
    Label: none  uuid: 07892354-ddaa-4443-90ea-f76a06accaba
    Total devices 1 FS bytes used 1.40GiB
    devid    1 size 4.00GiB used 3.00GiB path /dev/sda4

The bug is quite nasty that you can't either unmount /dev/sda4 or
/dev/mmcblk0p4. And the problem does not get solved until you take sda
out of the system on to another system to change its fsid using the
'btrfstune -u' command.

Signed-off-by: Anand Jain <anand.jain@oracle.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
2018-12-17 14:51:34 +01:00
Hans van Kranenburg b50836edf9 btrfs: introduce nparity raid_attr
Instead of hardcoding exceptions for RAID5 and RAID6 in the code, use an
nparity field in raid_attr.

Signed-off-by: Hans van Kranenburg <hans.van.kranenburg@mendix.com>
Signed-off-by: David Sterba <dsterba@suse.com>
2018-12-17 14:51:34 +01:00
Hans van Kranenburg da612e31ae btrfs: fix ncopies raid_attr for RAID56
RAID5 and RAID6 profile store one copy of the data, not 2 or 3. These
values are not yet used anywhere so there's no change.

Reviewed-by: Nikolay Borisov <nborisov@suse.com>
Signed-off-by: Hans van Kranenburg <hans.van.kranenburg@mendix.com>
Signed-off-by: David Sterba <dsterba@suse.com>
2018-12-17 14:51:33 +01:00
Hans van Kranenburg baf92114c7 btrfs: alloc_chunk: fix more DUP stripe size handling
Commit 92e222df7b "btrfs: alloc_chunk: fix DUP stripe size handling"
fixed calculating the stripe_size for a new DUP chunk.

However, the same calculation reappears a bit later, and that one was
not changed yet. The resulting bug that is exposed is that the newly
allocated device extents ('stripes') can have a few MiB overlap with the
next thing stored after them, which is another device extent or the end
of the disk.

The scenario in which this can happen is:
* The block device for the filesystem is less than 10GiB in size.
* The amount of contiguous free unallocated disk space chosen to use for
  chunk allocation is 20% of the total device size, or a few MiB more or
  less.

An example:
- The filesystem device is 7880MiB (max_chunk_size gets set to 788MiB)
- There's 1578MiB unallocated raw disk space left in one contiguous
  piece.

In this case stripe_size is first calculated as 789MiB, (half of
1578MiB).

Since 789MiB (stripe_size * data_stripes) > 788MiB (max_chunk_size), we
enter the if block. Now stripe_size value is immediately overwritten
while calculating an adjusted value based on max_chunk_size, which ends
up as 788MiB.

Next, the value is rounded up to a 16MiB boundary, 800MiB, which is
actually more than the value we had before. However, the last comparison
fails to detect this, because it's comparing the value with the total
amount of free space, which is about twice the size of stripe_size.

In the example above, this means that the resulting raw disk space being
allocated is 1600MiB, while only a gap of 1578MiB has been found. The
second device extent object for this DUP chunk will overlap for 22MiB
with whatever comes next.

The underlying problem here is that the stripe_size is reused all the
time for different things. So, when entering the code in the if block,
stripe_size is immediately overwritten with something else. If later we
decide we want to have the previous value back, then the logic to
compute it was copy pasted in again.

With this change, the value in stripe_size is not unnecessarily
destroyed, so the duplicated calculation is not needed any more.

Signed-off-by: Hans van Kranenburg <hans.van.kranenburg@mendix.com>
Signed-off-by: David Sterba <dsterba@suse.com>
2018-12-17 14:51:33 +01:00
Hans van Kranenburg 23f0ff1ec4 btrfs: alloc_chunk: improve chunk size variable name
The variable num_bytes is really a way too generic name for a variable
in this function. There are a dozen other variables that hold a number
of bytes as value.

Give it a name that actually describes what it does, which is holding
the size of the chunk that we're allocating.

Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: Hans van Kranenburg <hans.van.kranenburg@mendix.com>
Signed-off-by: David Sterba <dsterba@suse.com>
2018-12-17 14:51:33 +01:00
Hans van Kranenburg 2f29df4fc2 btrfs: alloc_chunk: do not refurbish num_bytes
The variable num_bytes is used to store the chunk length of the chunk
that we're allocating. Do not reuse it for something really different in
the same function.

Reviewed-by: Nikolay Borisov <nborisov@suse.com>
Signed-off-by: Hans van Kranenburg <hans.van.kranenburg@mendix.com>
Signed-off-by: David Sterba <dsterba@suse.com>
2018-12-17 14:51:33 +01:00
Ethan Lien 3cd24c6980 btrfs: use tagged writepage to mitigate livelock of snapshot
Snapshot is expected to be fast. But if there are writers steadily
creating dirty pages in our subvolume, the snapshot may take a very long
time to complete. To fix the problem, we use tagged writepage for
snapshot flusher as we do in the generic write_cache_pages(), so we can
omit pages dirtied after the snapshot command.

This does not change the semantics regarding which data get to the
snapshot, if there are pages being dirtied during the snapshotting
operation.  There's a sync called before snapshot is taken in old/new
case, any IO in flight just after that may be in the snapshot but this
depends on other system effects that might still sync the IO.

We do a simple snapshot speed test on a Intel D-1531 box:

fio --ioengine=libaio --iodepth=32 --bs=4k --rw=write --size=64G
--direct=0 --thread=1 --numjobs=1 --time_based --runtime=120
--filename=/mnt/sub/testfile --name=job1 --group_reporting & sleep 5;
time btrfs sub snap -r /mnt/sub /mnt/snap; killall fio

original: 1m58sec
patched:  6.54sec

This is the best case for this patch since for a sequential write case,
we omit nearly all pages dirtied after the snapshot command.

For a multi writers, random write test:

fio --ioengine=libaio --iodepth=32 --bs=4k --rw=randwrite --size=64G
--direct=0 --thread=1 --numjobs=4 --time_based --runtime=120
--filename=/mnt/sub/testfile --name=job1 --group_reporting & sleep 5;
time btrfs sub snap -r /mnt/sub /mnt/snap; killall fio

original: 15.83sec
patched:  10.35sec

The improvement is smaller compared to the sequential write case,
since we omit only half of the pages dirtied after snapshot command.

Reviewed-by: Nikolay Borisov <nborisov@suse.com>
Signed-off-by: Ethan Lien <ethanlien@synology.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
2018-12-17 14:51:33 +01:00
Nikolay Borisov c629732d24 btrfs: Remove unused extent_state argument from btrfs_writepage_endio_finish_ordered
This parameter was never used, yet was part of the interface of the
function ever since its introduction as extent_io_ops::writepage_end_io_hook
in e6dcd2dc9c ("Btrfs: New data=ordered implementation"). Now that
NULL is passed everywhere as a value for this parameter let's remove it
for good. No functional changes.

Signed-off-by: Nikolay Borisov <nborisov@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
2018-12-17 14:51:32 +01:00
Nikolay Borisov 8cc0237abc btrfs: Remove extent_page_data argument from writepage_delalloc
The only remaining use of the 'epd' argument in writepage_delalloc is
to reference the extent_io_tree which was set in extent_writepages. Since
it is guaranteed that page->mapping of any page passed to
writepage_delalloc (and __extent_writepage as the sole caller) to be
equal to that passed in extent_writepages we can directly get the
io_tree via the already passed inode (which is also taken from
page->mapping->host). No functional changes.

Signed-off-by: Nikolay Borisov <nborisov@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
2018-12-17 14:51:32 +01:00
Nikolay Borisov 7789a55aa1 btrfs: Move epd::extent_locked check to writepage_delalloc's caller
If epd::extent_locked is set then writepage_delalloc terminates. Make
this a bit more apparent in the caller by simply bubbling the check up.
This enables to remove epd as an argument to writepage_delalloc in a
future patch. No functional change.

Signed-off-by: Nikolay Borisov <nborisov@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
2018-12-17 14:51:32 +01:00
Nikolay Borisov fc8a168aa9 btrfs: Check for missing device before bio submission in btrfs_map_bio
Before btrfs_map_bio submits all stripe bios it does a number of checks
to ensure the device for every stripe is present. However, it doesn't do
a DEV_STATE_MISSING check, instead this is relegated to the lower level
btrfs_schedule_bio (in the async submission case, sync submission
doesn't check DEV_STATE_MISSING at all). Additionally
btrfs_schedule_bios does the duplicate device->bdev check which has
already been performed in btrfs_map_bio.

This patch moves the DEV_STATE_MISSING check in btrfs_map_bio and
removes the duplicate device->bdev check. Doing so ensures that no bio
cloning/submission happens for both async/sync requests in the face of
missing device. This makes the async io submission path slightly shorter
in terms of instruction count. No functional changes.

Reviewed-by: Josef Bacik <josef@toxicpanda.com>
Reviewed-by: Anand Jain <anand.jain@oracle.com>
Signed-off-by: Nikolay Borisov <nborisov@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
2018-12-17 14:51:32 +01:00
Anand Jain ab457246f8 btrfs: remove redundant replace_state init
dev_replace::replace_state has been set to
BTRFS_DEV_REPLACE_ITEM_STATE_NEVER_STARTED (0) in the same function,
So delete the line which sets replace_state = 0;

Reviewed-by: Nikolay Borisov <nborisov@suse.com>
Signed-off-by: Anand Jain <anand.jain@oracle.com>
Signed-off-by: David Sterba <dsterba@suse.com>
2018-12-17 14:51:32 +01:00
Filipe Manana 6d4cbf7903 Btrfs: remove no longer used io_err from btrfs_log_ctx
The io_err field of struct btrfs_log_ctx is no longer used after the
recent simplification of the fast fsync path, where we now wait for
ordered extents to complete before logging the inode. We did this in
commit b5e6c3e170 ("btrfs: always wait on ordered extents at fsync
time") and commit a2120a473a ("btrfs: clean up the left over
logged_list usage") removed its last use.

Reviewed-by: Nikolay Borisov <nborisov@suse.com>
Reviewed-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
2018-12-17 14:51:31 +01:00
Filipe Manana 59b0713a8a Btrfs: simpler and more efficient cleanup of a log tree's extent io tree
We currently are in a loop finding each range (corresponding to a btree
node/leaf) in a log root's extent io tree and then clean it up. This is a
waste of time since we are traversing the extent io tree's rb_tree more
times then needed (one for a range lookup and another for cleaning it up)
without any good reason.

We free the log trees when we are in the critical section of a transaction
commit (the transaction state is set to TRANS_STATE_COMMIT_DOING), so it's
of great convenience to do everything as fast as possible in order to
reduce the time we block other tasks from starting a new transaction.

So fix this by traversing the extent io tree once and cleaning up all its
records in one go while traversing it.

Reviewed-by: Nikolay Borisov <nborisov@suse.com>
Reviewed-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
2018-12-17 14:51:31 +01:00
Nikolay Borisov 46cc775e29 btrfs: Adjust loop in free_extent_buffer
The loop construct in free_extent_buffer was added in
242e18c7c1 ("Btrfs: reduce lock contention on extent buffer locks")
as means of reducing the times the eb lock is taken, the non-last ref
count is decremented and lock is released. As the special handling
of UNMAPPED extent buffers was removed now there is only one decrement
op which is happening for EXTENT_BUFFER_UNMAPPED case.

This commit modifies the loop condition so that in case of UNMAPPED
buffers the eb's lock is taken only if we are 100% sure the eb is going
to be freed by the current executor of the code. Additionally, remove
superfluous ref count ops in btrfs test.

Signed-off-by: Nikolay Borisov <nborisov@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
2018-12-17 14:51:31 +01:00
Nikolay Borisov 9cfc8ba712 btrfs: Remove special handling of EXTENT_BUFFER_UNMAPPED while freeing
Now that the whole of btrfs code has been audited for eb reference count
management it's time to remove the hunk in free_extent_buffer that
essentially considered the condition

  "eb->ref == 2 && EXTENT_BUFFER_DUMMY"

to equal "eb->ref = 1". Also remove the last location
which takes an extra reference count in alloc_test_extent_buffer.

Signed-off-by: Nikolay Borisov <nborisov@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
2018-12-17 14:51:31 +01:00
Nikolay Borisov df44971468 btrfs: Remove unnecessary tree locking code in qgroup_rescan_leaf
In qgroup_rescan_leaf a copy is made of the target leaf by calling
btrfs_clone_extent_buffer. The latter allocates a new buffer and
attaches a new set of pages and copies the content of the source buffer.
The new scratch buffer is only used to iterate it's items, it's not
published anywhere and cannot be accessed by a third party.

Hence, it's not necessary to perform any locking on it whatsoever.
Furthermore, remove the extra extent_buffer_get call since the new
buffer is always allocated with a reference count of 1 which is
sufficient here.  No functional changes.

Signed-off-by: Nikolay Borisov <nborisov@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
2018-12-17 14:51:31 +01:00
Nikolay Borisov 8c7eeb6557 btrfs: Remove extra reference count bumps in btrfs_compare_trees
When the 2 comparison trees roots are initialised they are private to
the function and already have reference counts of 1 each. There is no
need to further increment the reference count since the cloned buffers
are already accessed via struct btrfs_path. Eventually the 2 paths used
for comparison are going to be released, effectively disposing of the
cloned buffers.

Signed-off-by: Nikolay Borisov <nborisov@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
2018-12-17 14:51:30 +01:00
Nikolay Borisov 24cee18a1c btrfs: Remove extraneous extent_buffer_get from tree_mod_log_rewind
When a rewound buffer is created it already has a ref count of 1 and the
dummy flag set. Then another ref is taken bumping the count to 2.
Finally when this buffer is released from btrfs_release_path the extra
reference is decremented by the special handling code in
free_extent_buffer.

However, this special code is in fact redundant sinca ref count of 1 is
still correct since the buffer is only accessed via btrfs_path struct.
This paves the way forward of removing the special handling in
free_extent_buffer.

Signed-off-by: Nikolay Borisov <nborisov@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
2018-12-17 14:51:30 +01:00
Nikolay Borisov 6c122e2a0c btrfs: Remove redundant extent_buffer_get in get_old_root
get_old_root used used only by btrfs_search_old_slot to initialise the
path structure. The old root is always a cloned buffer (either via alloc
dummy or via btrfs_clone_extent_buffer) and its reference count is 2: 1
from allocation, 1 from extent_buffer_get call in get_old_root.

This latter explicit ref count acquire operation is in fact unnecessary
since the semantic is such that the newly allocated buffer is handed
over to the btrfs_path for lifetime management. Considering this just
remove the extra extent_buffer_get in get_old_root.

Signed-off-by: Nikolay Borisov <nborisov@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
2018-12-17 14:51:30 +01:00
Nikolay Borisov 5c623d334a btrfs: Remove needless tree locking in iterate_inode_extrefs
In iterate_inode_exrefs the eb is cloned via btrfs_clone_extent_buffer
which creates a private extent buffer with the dummy flag set and ref
count of 1. Then this buffer is locked for reading and its ref count is
incremented by 1. Finally it's fed to the passed iterate_irefs_t
function. The actual iterate call back is inode_to_path (coming from
paths_from_inode) which feeds the eb to btrfs_ref_to_path. In this final
function the passed eb is only read by first assigning it to the local
eb variable. This variable is only modified in the case another eb was
referenced from the passed path that is eb != eb_in check triggers.

Considering this there is no point in locking the cloned eb in
iterate_inode_refs since it's never being modified and is not published
anywhere. Furthermore the cloned eb is completely fine having its ref
count be 1.

Signed-off-by: Nikolay Borisov <nborisov@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
2018-12-17 14:51:30 +01:00
Nikolay Borisov e5bba0b0f8 btrfs: Remove needless tree locking in iterate_inode_refs
In iterate_inode_refs the eb is cloned via btrfs_clone_extent_buffer
which creates a private extent buffer with the dummy flag set and ref
count of 1. Then this buffer is locked for reading and its ref count is
incremented by 1. Finally it's fed to the passed iterate_irefs_t
function. The actual iterate call back is inode_to_path (coming from
paths_from_inode) which feeds the eb to btrfs_ref_to_path. In this final
function the passed eb is only read by first assigning it to the local
eb variable. This variable is only modified in the case another eb was
referenced from the passed path that is eb != eb_in check triggers.

Considering this there is no point in locking the cloned eb in
iterate_inode_refs since it's never being modified and is not published
anywhere. Furthermore the cloned eb is completely fine having its ref
count be 1.

Signed-off-by: Nikolay Borisov <nborisov@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
2018-12-17 14:51:30 +01:00
Qu Wenruo d9cb2459b2 btrfs: tests: Use BTRFS_MAX_EXTENT_SIZE to replace the intermediate number
In extent-io self test, we need 2 ordered extents at its maximum size to
do the test.

Instead of using the intermediate numbers, use BTRFS_MAX_EXTENT_SIZE for
@max_bytes, and twice @max_bytes for @total_dirty.  This should explain
why we need all these magic numbers and prevent people to modify them by
accident.

Reviewed-by: Nikolay Borisov <nborisov@suse.com>
Signed-off-by: Qu Wenruo <wqu@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
2018-12-17 14:51:30 +01:00
Omar Sandoval ed46ff3d42 Btrfs: support swap files
Btrfs has not allowed swap files since commit 35054394c4 ("Btrfs: stop
providing a bmap operation to avoid swapfile corruptions"). However, now
that the proper restrictions are in place, Btrfs can support swap files
through the swap file a_ops, similar to iomap in commit 67482129cd
("iomap: add a swapfile activation function").

For Btrfs, activation needs to make sure that the file can be used as a
swap file, which currently means that it must be fully allocated as
NOCOW with no compression on one device. It must also do the proper
tracking so that ioctls will not interfere with the swap file.
Deactivation clears this tracking.

Signed-off-by: Omar Sandoval <osandov@fb.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
2018-12-17 14:51:29 +01:00
Omar Sandoval 60ca842e34 Btrfs: rename and export get_chunk_map
The Btrfs swap code is going to need it, so give it a btrfs_ prefix and
make it non-static.

Reviewed-by: Nikolay Borisov <nborisov@suse.com>
Signed-off-by: Omar Sandoval <osandov@fb.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
2018-12-17 14:51:29 +01:00
Omar Sandoval eede2bf34f Btrfs: prevent ioctls from interfering with a swap file
A later patch will implement swap file support for Btrfs, but before we
do that, we need to make sure that the various Btrfs ioctls cannot
change a swap file.

When a swap file is active, we must make sure that the extents of the
file are not moved and that they don't become shared. That means that
the following are not safe:

- chattr +c (enable compression)
- reflink
- dedupe
- snapshot
- defrag

Don't allow those to happen on an active swap file.

Additionally, balance, resize, device remove, and device replace are
also unsafe if they affect an active swapfile. Add a red-black tree of
block groups and devices which contain an active swapfile. Relocation
checks each block group against this tree and skips it or errors out for
balance or resize, respectively. Device remove and device replace check
the tree for the device they will operate on.

Note that we don't have to worry about chattr -C (disable nocow), which
we ignore for non-empty files, because an active swapfile must be
non-empty and can't be truncated. We also don't have to worry about
autodefrag because it's only done on COW files. Truncate and fallocate
are already taken care of by the generic code. Device add doesn't do
relocation so it's not an issue, either.

Signed-off-by: Omar Sandoval <osandov@fb.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
2018-12-17 14:51:29 +01:00
Nikolay Borisov abbb55f4cd btrfs: Remove extent_io_ops::split_extent_hook callback
This is the counterpart to merge_extent_hook, similarly, it's used only
for data/freespace inodes so let's remove it, rename it and call it
directly where necessary. No functional changes.

Reviewed-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: Nikolay Borisov <nborisov@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
2018-12-17 14:51:29 +01:00
Nikolay Borisov 5c848198aa btrfs: Remove extent_io_ops::merge_extent_hook callback
This callback is used only for data and free space inodes. Such inodes
are guaranteed to have their extent_io_tree::private_data set to the
inode struct. Exploit this fact to directly call the function. Also give
it a more descriptive name. No functional changes.

Reviewed-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: Nikolay Borisov <nborisov@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
2018-12-17 14:51:28 +01:00
Nikolay Borisov a36bb5f9a9 btrfs: Remove extent_io_ops::clear_bit_hook callback
This is the counterpart to ex-set_bit_hook (now btrfs_set_delalloc_extent),
similar to what was done before remove clear_bit_hook and rename the
function. No functional changes.

Reviewed-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: Nikolay Borisov <nborisov@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
2018-12-17 14:51:28 +01:00
Nikolay Borisov e06a1fc99c btrfs: Remove extent_io_ops::set_bit_hook extent_io callback
This callback is used to properly account delalloc extents for data
inodes (ordinary file inodes and freespace v1 inodes). Those can be
easily identified since they have their extent_io trees ->private_data
member point to the inode. Let's exploit this fact to remove the
needless indirection through extent_io_hooks and directly call the
function. Also give the function a name which reflects its purpose -
btrfs_set_delalloc_extent.

This patch also modified test_find_delalloc so that the extent_io_tree
used for testing doesn't have its ->private_data set which would have
caused a crash in btrfs_set_delalloc_extent due to the btrfs_inode->root
member not being initialised. The old version of the code also didn't
call set_bit_hook since the extent_io ops weren't set for the inode.  No
functional changes.

Reviewed-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: Nikolay Borisov <nborisov@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
2018-12-17 14:51:28 +01:00
Nikolay Borisov 65a680f6b7 btrfs: Remove extent_io_ops::check_extent_io_range callback
This callback was only used in debug builds by btrfs_leak_debug_check.
A better approach is to move its implementation in
btrfs_leak_debug_check and ensure the latter is only executed for extent
tree which have ->private_data set i.e. relate to a data node and not
the btree one. No functional changes.

Reviewed-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: Nikolay Borisov <nborisov@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
2018-12-17 14:51:28 +01:00
Nikolay Borisov 7087a9d8db btrfs: Remove extent_io_ops::writepage_end_io_hook
This callback is ony ever called for data page writeout so there is no
need to actually abstract it via extent_io_ops. Lets just export it,
remove the definition of the callback and call it directly in the
functions that invoke the callback. Also rename the function to
btrfs_writepage_endio_finish_ordered since what it really does is
account finished io in the ordered extent data structures.  No
functional changes.

Reviewed-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: Nikolay Borisov <nborisov@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
2018-12-17 14:51:28 +01:00
Nikolay Borisov d75855b451 btrfs: Remove extent_io_ops::writepage_start_hook
This hook is called only from __extent_writepage_io which is already
called only from the data page writeout path. So there is no need to
make an indirect call via extent_io_ops. This patch just removes the
callback definition, exports the callback function and calls it directly
at the only call site. Also give the function a more descriptive name.
No functional changes.

Reviewed-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: Nikolay Borisov <nborisov@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
2018-12-17 14:51:27 +01:00
Nikolay Borisov 5eaad97af8 btrfs: Remove extent_io_ops::fill_delalloc
This callback is called only from writepage_delalloc which in turn is
guaranteed to be called from the data page writeout path. In the end
there is no reason to have the call to this function to be indrected via
the extent_io_ops structure. This patch removes the callback definition,
exports the function and calls it directly. No functional changes.

Reviewed-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: Nikolay Borisov <nborisov@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
[ rename to btrfs_run_delalloc_range ]
Signed-off-by: David Sterba <dsterba@suse.com>
2018-12-17 14:51:27 +01:00
Nikolay Borisov 06f2548f9d btrfs: Add function to distinguish between data and btree inode
This will be used in future patches that remove the optional
extent_io_ops callbacks.

Signed-off-by: Nikolay Borisov <nborisov@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
2018-12-17 14:51:27 +01:00
Qu Wenruo 05a37c4860 btrfs: volumes: Make sure no dev extent is beyond device boundary
Add extra dev extent end check against device boundary.

Signed-off-by: Qu Wenruo <wqu@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
2018-12-17 14:51:27 +01:00
Qu Wenruo 5eb193812a btrfs: volumes: Make sure there is no overlap of dev extents at mount time
Enhance btrfs_verify_dev_extents() to remember previous checked dev
extents, so it can verify no dev extents can overlap.

Analysis from Hans:

"Imagine allocating a DATA|DUP chunk.

 In the chunk allocator, we first set...
   max_stripe_size = SZ_1G;
   max_chunk_size = BTRFS_MAX_DATA_CHUNK_SIZE
 ... which is 10GiB.

 Then...
   /* we don't want a chunk larger than 10% of writeable space */
   max_chunk_size = min(div_factor(fs_devices->total_rw_bytes, 1),
       		 max_chunk_size);

 Imagine we only have one 7880MiB block device in this filesystem. Now
 max_chunk_size is down to 788MiB.

 The next step in the code is to search for max_stripe_size * dev_stripes
 amount of free space on the device, which is in our example 1GiB * 2 =
 2GiB. Imagine the device has exactly 1578MiB free in one contiguous
 piece. This amount of bytes will be put in devices_info[ndevs - 1].max_avail

 Next we recalculate the stripe_size (which is actually the device extent
 length), based on the actual maximum amount of available raw disk space:
   stripe_size = div_u64(devices_info[ndevs - 1].max_avail, dev_stripes);

 stripe_size is now 789MiB

 Next we do...
   data_stripes = num_stripes / ncopies
 ...where data_stripes ends up as 1, because num_stripes is 2 (the amount
 of device extents we're going to have), and DUP has ncopies 2.

 Next there's a check...
   if (stripe_size * data_stripes > max_chunk_size)
 ...which matches because 789MiB * 1 > 788MiB.

 We go into the if code, and next is...
   stripe_size = div_u64(max_chunk_size, data_stripes);
 ...which resets stripe_size to max_chunk_size: 788MiB

 Next is a fun one...
   /* bump the answer up to a 16MB boundary */
   stripe_size = round_up(stripe_size, SZ_16M);
 ...which changes stripe_size from 788MiB to 800MiB.

 We're not done changing stripe_size yet...
   /* But don't go higher than the limits we found while searching
    * for free extents
    */
   stripe_size = min(devices_info[ndevs - 1].max_avail,
       	      stripe_size);

 This is bad. max_avail is twice the stripe_size (we need to fit 2 device
 extents on the same device for DUP).

 The result here is that 800MiB < 1578MiB, so it's unchanged. However,
 the resulting DUP chunk will need 1600MiB disk space, which isn't there,
 and the second dev_extent might extend into the next thing (next
 dev_extent? end of device?) for 22MiB.

 The last shown line of code relies on a situation where there's twice
 the value of stripe_size present as value for the variable stripe_size
 when it's DUP. This was actually the case before commit 92e222df7b
 "btrfs: alloc_chunk: fix DUP stripe size handling", from which I quote:
   "[...] in the meantime there's a check to see if the stripe_size does
 not exceed max_chunk_size. Since during this check stripe_size is twice
 the amount as intended, the check will reduce the stripe_size to
 max_chunk_size if the actual correct to be used stripe_size is more than
 half the amount of max_chunk_size."

 In the previous version of the code, the 16MiB alignment (why is this
 done, by the way?) would result in a 50% chance that it would actually
 do an 8MiB alignment for the individual dev_extents, since it was
 operating on double the size. Does this matter?

 Does it matter that stripe_size can be set to anything which is not
 16MiB aligned because of the amount of remaining available disk space
 which is just taken?

 What is the main purpose of this round_up?

 The most straightforward thing to do seems something like...
   stripe_size = min(
       div_u64(devices_info[ndevs - 1].max_avail, dev_stripes),
       stripe_size
   )
 ..just putting half of the max_avail into stripe_size."

Link: https://lore.kernel.org/linux-btrfs/b3461a38-e5f8-f41d-c67c-2efac8129054@mendix.com/
Reported-by: Hans van Kranenburg <hans.van.kranenburg@mendix.com>
Signed-off-by: Qu Wenruo <wqu@suse.com>
[ add analysis from report ]
Signed-off-by: David Sterba <dsterba@suse.com>
2018-12-17 14:51:27 +01:00
Qu Wenruo e72d79d6bc btrfs: Refactor find_free_extent loops update into find_free_extent_update_loop
We have a complex loop design for find_free_extent(), that has different
behavior for each loop, some even includes new chunk allocation.

Instead of putting such a long code into find_free_extent() and makes it
harder to read, just extract them into find_free_extent_update_loop().

With all the cleanups, the main find_free_extent() should be pretty
barebone:

find_free_extent()
|- Iterate through all block groups
|  |- Get a valid block group
|  |- Try to do clustered allocation in that block group
|  |- Try to do unclustered allocation in that block group
|  |- Check if the result is valid
|  |  |- If valid, then exit
|  |- Jump to next block group
|
|- Push harder to find free extents
   |- If not found, re-iterate all block groups

Signed-off-by: Qu Wenruo <wqu@suse.com>
Reviewed-by: Su Yue <suy.fnst@cn.fujitsu.com>
[ copy callchain from changelog to function comment ]
Signed-off-by: David Sterba <dsterba@suse.com>
2018-12-17 14:51:26 +01:00
Qu Wenruo e1a4184815 btrfs: Refactor unclustered extent allocation into find_free_extent_unclustered()
This patch will extract unclsutered extent allocation code into
find_free_extent_unclustered().

And this helper function will use return value to indicate what to do
next.

This should make find_free_extent() a little easier to read.

Signed-off-by: Qu Wenruo <wqu@suse.com>
Reviewed-by: Su Yue <suy.fnst@cn.fujitsu.com>
Reviewed-by: Josef Bacik <josef@toxicpanda.com>
[Update merge conflict with fb5c39d7a8 ("btrfs: don't use ctl->free_space for max_extent_size")]
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
2018-12-17 14:51:26 +01:00
Qu Wenruo d06e3bb690 btrfs: Refactor clustered extent allocation into find_free_extent_clustered
We have two main methods to find free extents inside a block group:

1) clustered allocation
2) unclustered allocation

This patch will extract the clustered allocation into
find_free_extent_clustered() to make it a little easier to read.

Instead of jumping between different labels in find_free_extent(), the
helper function will use return value to indicate different behavior.

Signed-off-by: Qu Wenruo <wqu@suse.com>
Reviewed-by: Su Yue <suy.fnst@cn.fujitsu.com>
Reviewed-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: David Sterba <dsterba@suse.com>
2018-12-17 14:51:26 +01:00
Qu Wenruo b4bd745d12 btrfs: Introduce find_free_extent_ctl structure for later rework
Instead of tons of different local variables in find_free_extent(),
extract them into find_free_extent_ctl structure, and add better
explanation for them.

Some modification may looks redundant, but will later greatly simplify
function parameter list during find_free_extent() refactor.

Also add two comments to co-operate with fb5c39d7a8 ("btrfs: don't use
ctl->free_space for max_extent_size"), to make ffe_ctl->max_extent_size
update more reader-friendly.

Signed-off-by: Qu Wenruo <wqu@suse.com>
Reviewed-by: Su Yue <suy.fnst@cn.fujitsu.com>
Reviewed-by: Josef Bacik <josef@toxicpanda.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
2018-12-17 14:51:26 +01:00
Lu Fengqi e2907c1a6a btrfs: extent-tree: Detect bytes_pinned underflow earlier
Introduce a new wrapper update_bytes_pinned to replace open coded
bytes_pinned modifiers. Now the underflows of space_info::bytes_pinned
get detected and reported.

Reviewed-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: Lu Fengqi <lufq.fnst@cn.fujitsu.com>
Signed-off-by: David Sterba <dsterba@suse.com>
2018-12-17 14:51:26 +01:00
Qu Wenruo 9f9b8e8d0e btrfs: extent-tree: Detect bytes_may_use underflow earlier
Although we have space_info::bytes_may_use underflow detection in
btrfs_free_reserved_data_space_noquota(), we have more callers who are
subtracting number from space_info::bytes_may_use.

So instead of doing underflow detection for every caller, introduce a
new wrapper update_bytes_may_use() to replace open coded bytes_may_use
modifiers.

This also introduce a macro to declare more wrappers, but currently
space_info::bytes_may_use is the mostly interesting one.

Reviewed-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: Qu Wenruo <wqu@suse.com>
Signed-off-by: Lu Fengqi <lufq.fnst@cn.fujitsu.com>
Signed-off-by: David Sterba <dsterba@suse.com>
2018-12-17 14:51:25 +01:00
Filipe Manana 85dd506c8e Btrfs: remove no longer used stuff for tracking pending ordered extents
Tracking pending ordered extents per transaction was introduced in commit
50d9aa99bd ("Btrfs: make sure logged extents complete in the current
transaction V3") and later updated in commit 161c3549b4 ("Btrfs: change
how we wait for pending ordered extents").

However now that on fsync we always wait for ordered extents to complete
before logging, done in commit 5636cf7d6d ("btrfs: remove the logged
extents infrastructure"), we no longer need the stuff to track for pending
ordered extents, which was not completely removed in the mentioned commit.
So remove the remaining of the pending ordered extents infrastructure.

Reviewed-by: Liu Bo <bo.liu@linux.alibaba.com>
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
2018-12-17 14:51:25 +01:00
Filipe Manana ce02f03266 Btrfs: remove no longer used logged range variables when logging extents
The logged_start and logged_end variables, at btrfs_log_changed_extents,
were added in commit 8c6c592831 ("btrfs: log csums for all modified
extents"). However since the recent simplification for fsync, which makes
us wait for all ordered extents to complete before logging extents, we
no longer need those variables. Commit a2120a473a ("btrfs: clean up the
left over logged_list usage") forgot to remove them.

Reviewed-by: Nikolay Borisov <nborisov@suse.com>
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
2018-12-17 14:51:25 +01:00
Linus Torvalds d089709045 for-4.20-rc5-tag
-----BEGIN PGP SIGNATURE-----
 
 iQIzBAABCgAdFiEE8rQSAMVO+zA4DBdWxWXV+ddtWDsFAlwH0k8ACgkQxWXV+ddt
 WDtmVg/+Kgvk7laQI9bLEr1/30eG1JfBUMHcVE1F8+g99l28m1Yihjd21j9norVd
 YexBz53jgKou+zV+37CKWBYT1uDPq7CIoxctkdE2j9U0s+RmsqDrhech0dsBsfMR
 jo9VnHJFuJSxGMhjfGnFV+wMtAr4q5aQptNGBl+hR1MvMneroktFv+0WiLmp0Vhj
 +6Iq9WAClJYpgk//cI7nhKkscdzWwRyN3V9RUtdNeYklk1D7l1WprlaPzw22WA9u
 VjQVMICjEaJeIixIwT/D8lz05QgjKlqy1z6faYG5JuJxoYQikuNv/xe2dhZVm35A
 aNsBR0byf3zzuXKQZAlvXJ6/gYPvep+KI7epPyBOdycaqoZza7rQ+/MkSAgQ77Vk
 yBnQuhqiw9Srjh6LDWFkNclVln2wymRKd1SqpZmFPRZre/8L+DU+I8RRaeS2/WcE
 M2k+awRD0oVofbB+hxkFIoR+I1Ggkp2rxQlTT/41tGx0geWC3AGX+TlKSW6ZM5HD
 lRmRXIsVocfighKEnI3Zy7ecZuwCI4/4D6+PQtyhCJb3tDigZ/a4UEYdSVucG8CG
 SuQ5YMn+MyyKT0wH8xkGKDGT15YZ+u9Q/BmPHZRL6sSouFpiCQHA5miD1YA+t1d9
 qMjH6Ycz46Y3j2M0BDfDcm714zoD5/bgeSy5SPC3Zh5lQCGpeIk=
 =VW/F
 -----END PGP SIGNATURE-----

Merge tag 'for-4.20-rc5-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux

Pull btrfs fix from David Sterba:
 "A patch in 4.19 introduced a sanity check that was too strict and a
  filesystem cannot be mounted.

  This happens for filesystems with more than 10 devices and has been
  reported by a few users so we need the fix to propagate to stable"

* tag 'for-4.20-rc5-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux:
  btrfs: tree-checker: Don't check max block group size as current max chunk size limit is unreliable
2018-12-05 09:58:17 -08:00