The logic to check for valid device areas is inverted relative to proper
use with iterate_devices.
The iterate_devices method calls its callback for every underlying
device in the target. If any callback returns non-zero, iterate_devices
exits immediately. But the callback device_area_is_valid() returns 0 on
error and 1 on success. The overall effect without is that an error is
issued only if every device is invalid.
This patch renames device_area_is_valid to device_area_is_invalid and
inverts the logic so that one invalid device is sufficient to raise
an error.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Implement the .iterate_devices for the origin and snapshot targets.
dm-snapshot's lack of .iterate_devices resulted in the inability to
properly establish queue_limits for both targets.
With 4K sector drives: an unfortunate side-effect of not establishing
proper limits in either targets' DM device was that IO to the devices
would fail even though both had been created without error.
Commit af4874e03e ("dm target:s introduce
iterate devices fn") in 2.6.31-rc1 should have implemented .iterate_devices
for dm-snap.c's origin and snapshot targets.
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
The function tracing_reset is deprecated for outside use of trace.c.
The new function to reset the the buffers is tracing_reset_online_cpus.
The reason for this is that resetting the buffers while the event
trace points are active can corrupt the buffers, because they may
be writing at the time of reset. The tracing_reset_online_cpus disables
writes and waits for current writers to finish.
This patch replaces all users of tracing_reset except for the latency
tracers. Those changes require more work and will be removed in the
following patches.
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Resetting the ring buffers while traces are happening can corrupt
the ring buffer and disable it (no kernel crash to worry about).
The safest thing to do is disable the ring buffers, call synchronize_sched()
to wait for all current writers to finish and then reset the buffer.
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
When reading the tracer from the trace file, updating the max latency
may corrupt the output. This patch disables the tracing of the max
latency while reading the trace file.
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
During development of the tracer, we would copy information from
the live tracer to the max tracer with one memcpy. Since then we
added a generic ring buffer and we handle the copies differently now.
Unfortunately, we never copied the critical section information, and
we lost the output:
# => started at: kmem_cache_alloc
# => ended at: kmem_cache_alloc
This patch adds back the critical start and end copying as well as
removes the unused "trace_idx" and "overrun" fields of the
trace_array_cpu structure.
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Currently the way RB_WARN_ON works, is to disable either the current
CPU buffer or all CPU buffers, depending on whether a ring_buffer or
ring_buffer_per_cpu struct was passed into the macro.
Most users of the RB_WARN_ON pass in the CPU buffer, so only the one
CPU buffer gets disabled but the rest are still active. This may
confuse users even though a warning is sent to the console.
This patch changes the macro to disable the entire buffer even if
the CPU buffer is passed in.
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
The latency tracers report the number of items in the trace buffer.
This uses the ring buffer data to calculate this. Because discarded
events are also counted, the numbers do not match the number of items
that are printed. The ring buffer also adds a "padding" item to the
end of each buffer page which also gets counted as a discarded item.
This patch decrements the counter to the page entries on a discard.
This allows us to ignore discarded entries while reading the buffer.
Decrementing the counter is still safe since it can only happen while
the committing flag is still set.
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
The function ring_buffer_event_discard can be used on any item in the
ring buffer, even after the item was committed. This function provides
no safety nets and is very race prone.
An item may be safely removed from the ring buffer before it is committed
with the ring_buffer_discard_commit.
Since there are currently no users of this function, and because this
function is racey and error prone, this patch removes it altogether.
Note, removing this function also allows the counters to ignore
all discarded events (patches will follow).
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
When the ring buffer uses an iterator (static read mode, not on the
fly reading), when it crosses a page boundery, it will skip the first
entry on the next page. The reason is that the last entry of a page
is usually padding if the page is not full. The padding will not be
returned to the user.
The problem arises on ring_buffer_read because it also increments the
iterator. Because both the read and peek use the same rb_iter_peek,
the rb_iter_peak will return the padding but also increment to the next
item. This is because the ring_buffer_peek will not incerment it
itself.
The ring_buffer_read will increment it again and then call rb_iter_peek
again to get the next item. But that will be the second item, not the
first one on the page.
The reason this never showed up before, is because the ftrace utility
always calls ring_buffer_peek first and only uses ring_buffer_read
to increment to the next item. The ring_buffer_peek will always keep
the pointer to a valid item and not padding. This just hid the bug.
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
The loops in the ring buffer that use cpu_relax are not dependent on
other CPUs. They simply came across some padding in the ring buffer and
are skipping over them. It is a normal loop and does not require a
cpu_relax.
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
If a commit is taking place on a CPU ring buffer, do not allow it to
be swapped. Return -EBUSY when this is detected instead.
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
The callers of reset must ensure that no commit can be taking place
at the time of the reset. If it does then we may corrupt the ring buffer.
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Functions invoked early when booting up a cpu can't use
tracing because mcount requires a valid 'current_thread_info()'
and TLB mappings to be setup.
The code path of sun4v_register_mondo_queues --> register_one_mondo
is one such case. sun4v_register_mondo_queues already has the
necessary 'notrace' annotation, but register_one_mondo does not.
Normally register_one_mondo is inlined so the bug doesn't trigger,
but with some config/compiler combinations, it won't be so we
must properly mark it notrace.
While we're here, add 'notrace' annoations to prom_printf and
prom_halt so that early error handling won't have the same problem.
Reported-by: Alexander Beregalov <a.beregalov@gmail.com>
Reported-by: Leif Sawyer <lsawyer@gci.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Compaq Presario R4000-series laptops are not sending a "volume up button
release" and "volume down button release" signal in the PS/2 protocol for
atkbd. The URL below has some of confirmed reports:
https://bugs.launchpad.net/ubuntu/+source/linux/+bug/385477
Signed-off-by: Dave Andrews <jetdog330@hotmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
kmem_cache_destroy() should call rcu_barrier() *after* kmem_cache_close() and
*before* sysfs_slab_remove() or risk rcu_free_slab() being called after
kmem_cache is deleted (kfreed).
rmmod nf_conntrack can crash the machine because it has to kmem_cache_destroy()
a SLAB_DESTROY_BY_RCU enabled cache.
Cc: <stable@kernel.org>
Reported-by: Zdenek Kabelac <zdenek.kabelac@gmail.com>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Acked-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Signed-off-by: Pekka Enberg <penberg@cs.helsinki.fi>
The function jffs2_nor_wbuf_flash_setup() doesn't allocate the verify buffer
if CONFIG_JFFS2_FS_WBUF_VERIFY is defined, so causing a kernel panic when
that macro is enabled and the verify function is called. Similarly the
jffs2_nor_wbuf_flash_cleanup() must free the buffer if
CONFIG_JFFS2_FS_WBUF_VERIFY is enabled.
The following patch fixes the problem.
The following patch applies to 2.6.30 kernel.
Signed-off-by: Massimo Cirillo <maxcir@gmail.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Cc: stable@kernel.org
Arithmetic conversion in the mask computation makes the upper word
of the second argument passed down to mtd->read_oob(), be always 0
(assuming 'offs' being a 64-bit signed long long type, and
'mtd->writesize' being a 32-bit unsigned int type).
This patch applies over the other one adding masking in nftl_write,
"nftl: write support is broken".
Signed-off-by: Dimitri Gorokhovik <dimitri.gorokhovik@free.fr>
Cc: Tim Gardner <tim.gardner@canonical.com>
Cc: Scott James Remnant <scott@canonical.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Write support is broken in NFTL. Fix it.
Signed-off-by: <dimitri.gorokhovik@free.fr>
Cc: Tim Gardner <tim.gardner@canonical.com>
Cc: Scott James Remnant <scott@canonical.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This is a compromise and a temporary workaround for bootup NMI
watchdog triggers some people see with qla2xxx devices present.
This happens when, for example:
CPU 0 is in the driver init and looping submitting mailbox commands to
load the firmware, then waiting for completion.
CPU 1 is receiving the device interrupts. CPU 1 is where the NMI
watchdog triggers.
CPU 0 is submitting mailbox commands fast enough that by the time CPU
1 returns from the device interrupt handler, a new one is pending.
This sequence runs for more than 5 seconds.
The problematic case is CPU 1's timer interrupt running when the
barrage of device interrupts begin. Then we have:
timer interrupt
return for softirq checking
pending, thus enable interrupts
qla2xxx interrupt
return
qla2xxx interrupt
return
... 5+ seconds pass
final qla2xxx interrupt for fw load
return
run timer softirq
return
At some point in the multi-second qla2xxx interrupt storm we trigger
the NMI watchdog on CPU 1 from the NMI interrupt handler.
The timer softirq, once we get back to running it, is smart enough to
run the timer work enough times to make up for the missed timer
interrupts.
However, the NMI watchdogs (both x86 and sparc) use the timer
interrupt count to notice the cpu is wedged. But in the above
scenerio we'll receive only one such timer interrupt even if we last
all the way back to running the timer softirq.
The default watchdog trigger point is only 5 seconds, which is pretty
low (the softwatchdog triggers at 60 seconds). So increase it to 30
seconds for now.
Signed-off-by: David S. Miller <davem@davemloft.net>
I had the codes for L1 D-cache load accesses and misses swapped
around, and the wrong codes for LL-cache accesses and misses.
This corrects them.
Reported-by: Corey Ashford <cjashfor@linux.vnet.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: <stable@kernel.org>
LKML-Reference: <19103.8514.709300.585484@cargo.ozlabs.ibm.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Three bytes of uninitialized kernel memory are currently leaked to user
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Reviewed-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The card model detection code introduced in 2.6.30 that tries to work
around partially broken EEPROM contents by reading the EEPROM directly
does not handle cards where the EEPROM has been omitted. In this case,
we have to use the default ID to allow the driver to load.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Reported-and-tested-by: Ozan Çağlayan <ozan@pardus.org.tr>
Cc: <stable@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The 32-bit parameters (len and csum) of csum_ipv6_magic() are passed in 64-bit
registers in2 and in4. The high order 32 bits of the registers were never
cleared, and garbage was sometimes calculated into the checksum.
Fix this by clearing the high order 32 bits of these registers.
Signed-off-by: Jiri Bohac <jbohac@suse.cz>
Signed-off-by: Tony Luck <tony.luck@intel.com>
arch/ia64/kernel/dma-mapping.c:14: warning: control reaches end of non-void function
arch/ia64/kernel/dma-mapping.c:14: warning: no return statement in function returning non-void
This warning was introduced by commit: 390bd132b2
Add dma_debug_init() for ia64
Signed-off-by: Tony Luck <tony.luck@intel.com>
These are full of unresolved problems, mainly that conversions don't
work 1-1 from hrtimers to tasklet_hrtimers because unlike hrtimers
tasklets can't be killed from softirq context.
And when a qdisc gets reset, that's exactly what we need to do here.
We'll work this out in the net-next-2.6 tree and if warranted we'll
backport that work to -stable.
This reverts the following 3 changesets:
a2cb6a4dd4
("pkt_sched: Fix bogon in tasklet_hrtimer changes.")
38acce2d79
("pkt_sched: Convert CBQ to tasklet_hrtimer.")
ee5f9757ea
("pkt_sched: Convert qdisc_watchdog to tasklet_hrtimer")
Signed-off-by: David S. Miller <davem@davemloft.net>
After commit 2b85a34e91
(net: No more expensive sock_hold()/sock_put() on each tx)
sk_free() frees socks conditionally and depends
on sk_wmem_alloc being set e.g. in sock_init_data(). But in some
cases sk_free() is called earlier, usually after other alloc errors.
Fix is to move sk_wmem_alloc initialization from sock_init_data()
to sk_alloc() itself.
Signed-off-by: Jarek Poplawski <jarkao2@gmail.com>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix a small typo in the compat ioctl handler that cause the swapext
compat handler to never be called.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Torsten Kaiser <just.for.lkml@googlemail.com>
Tested-by: Torsten Kaiser <just.for.lkml@googlemail.com>
Reviewed-by: Eric Sandeen <sandeen@sandeen.net>
Reviewed-by: Felix Blyakher <felixb@sgi.com>
Signed-off-by: Felix Blyakher <felixb@sgi.com>
The patch "block: Use accessor functions for queue limits"
(ae03bf639a) changed queue_max_sectors_store()
to use blk_queue_max_sectors() instead of directly assigning the value.
But blk_queue_max_sectors() differs a bit
1. It sets both max_sectors_kb, and max_hw_sectors_kb
2. Never allows one to change max_sectors_kb above BLK_DEF_MAX_SECTORS. If one
specifies a value greater then max_hw_sectors is set to that value but
max_sectors is set to BLK_DEF_MAX_SECTORS
I am not sure whether blk_queue_max_sectors() should be changed, as it seems
to be that way for a long time. And there may be callers dependent on that
behaviour.
This patch simply reverts to the older way of directly assigning the value to
max_sectors as it was before.
Signed-off-by: Nikanth Karthikesan <knikanth@suse.de>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Commit 4bc5d34135 is broken and causes regressions:
(1) cpufreq_driver->resume() and ->suspend() were only called on
__powerpc__, but you could set them on all architectures. In fact,
->resume() was defined and used before the PPC-related commit
42d4dc3f4e complained about in 4bc5d34135.
(2) Therfore, the resume functions in acpi_cpufreq and speedstep-smi
would never be called.
(3) This means speedstep-smi would be unusuable after suspend or resume.
The _real_ problem was calling cpufreq_driver->get() with interrupts
off, but it re-enabling interrupts on some platforms. Why is ->get()
necessary?
Some systems like to change the CPU frequency behind our
back, especially during BIOS-intensive operations like suspend or
resume. If such systems also use a CPU frequency-dependant timing loop,
delays might be off by large factors. Therefore, we need to ascertain
as soon as possible that the CPU frequency is indeed at the speed we
think it is. You can do this two ways: either setting it anew, or trying
to get it. The latter is what was done, the former also has the same IRQ
issue.
So, let's try something different: defer the checking to after interrupts
are re-enabled, by calling cpufreq_update_policy() (via schedule_work()).
Timings may be off until this later stage, so let's watch out for
resume regressions caused by the deferred handling of frequency changes
behind the kernel's back.
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Dave Jones <davej@redhat.com>
percpu incorrectly assumed that cpu0 was always there which led to the
following warning and eventual oops on sparc machines w/o cpu0.
WARNING: at mm/percpu.c:651 pcpu_map+0xdc/0x100()
Modules linked in:
Call Trace:
[000000000045eb70] warn_slowpath_common+0x50/0xa0
[000000000045ebdc] warn_slowpath_null+0x1c/0x40
[00000000004d493c] pcpu_map+0xdc/0x100
[00000000004d59a4] pcpu_alloc+0x3e4/0x4e0
[00000000004d5af8] __alloc_percpu+0x18/0x40
[00000000005b112c] __percpu_counter_init+0x4c/0xc0
...
Unable to handle kernel NULL pointer dereference
...
I7: <sysfs_new_dirent+0x30/0x120>
Disabling lock debugging due to kernel taint
Caller[000000000053c1b0]: sysfs_new_dirent+0x30/0x120
Caller[000000000053c7a4]: create_dir+0x24/0xc0
Caller[000000000053c870]: sysfs_create_dir+0x30/0x80
Caller[00000000005990e8]: kobject_add_internal+0xc8/0x200
...
Kernel panic - not syncing: Attempted to kill the idle task!
This patch fixes the problem by backporting parts from devel branch to
make percpu core not depend on the existence of cpu0.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Meelis Roos <mroos@linux.ee>
Cc: David Miller <davem@davemloft.net>
Do not forget to program the MCLK ratio for the I2S output.
Otherwise, the master clock frequency can be too high for
the DACs at sample frequencies above 96 kHz.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Cc: <stable@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In the recent change by Al Viro that changes verious subsystems
to use "struct path" one case was missed in the autofs4 module
which causes mounts to no longer expire.
Signed-off-by: Ian Kent <raven@themaw.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
My previous patch (commit 4f8ee2c9cc: "lmb: Remove __init from
lmb_end_of_DRAM()") removed __init in lmb.c but missed the fact that it
was also marked as such in the .h
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit log for commit 517d3cc15b
("[libata] ata_piix: Enable parallel scan") says:
This patch turns on parallel scanning for the ata_piix driver.
This driver is used on most netbooks (no AHCI for cheap storage it seems).
The scan is the dominating time factor in the kernel boot for these
devices; with this flag it gets cut in half for the device I used
for testing (eeepc).
Alan took a look at the driver source and concluded that it ought to be safe
to do for this driver. Alan has also checked with the hardware team.
and it is all true but once we put all things together additional
constraints for PATA controllers show up (some hardware registers
have per-host not per-port atomicity) and we risk misprogramming
the controller.
I used the following test to check whether the issue is real:
@@ -736,8 +736,20 @@ static void piix_set_piomode(struct ata_
(timings[pio][1] << 8);
}
pci_write_config_word(dev, master_port, master_data);
- if (is_slave)
+ if (is_slave) {
+ if (ap->port_no == 0) {
+ u8 tmp = slave_data;
+
+ while (slave_data == tmp) {
+ pci_read_config_byte(dev, slave_port, &tmp);
+ msleep(50);
+ }
+
+ dev_printk(KERN_ERR, &dev->dev, "PATA parallel scan "
+ "race detected\n");
+ }
pci_write_config_byte(dev, slave_port, slave_data);
+ }
/* Ensure the UDMA bit is off - it will be turned back on if
UDMA is selected */
and it indeed triggered the error message.
Lets fix all such races by adding an extra locking to ->set_piomode
and ->set_dmamode methods for PATA controllers.
[ Alan: would be better to take the host lock in libata-core for these
cases so that we fix all the adapters in one swoop. "Looks fine as a
temproary quickfix tho" ]
Cc: Arjan van de Ven <arjan@linux.intel.com>
Acked-by: Alan Cox <alan@linux.intel.com>
Cc: Jeff Garzik <jgarzik@redhat.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/anholt/drm-intel:
drm/i915: Improve CRTDDC mapping by using VBT info
drm/i915: Fix CPU-spinning hangs related to fence usage by using an LRU.
drm/i915: Set crtc/clone mask in different output devices
drm/i915: Always use SDVO_B detect bit for SDVO output detection.
drm/i915: Fix typo that broke SVID1 in intel_sdvo_multifunc_encoder()
drm/i915: Check if BIOS enabled dual-channel LVDS on 8xx, not only on 9xx
drm/i915: Set the multiplier for SDVO on G33 platform
init_preds() allocates about 5392 bytes of memory (on x86_32) for
a TRACE_EVENT. With my config, at system boot total memory occupied
is:
5392 * (642 + 15) == 3459KB
642 == cat available_events | wc -l
15 == number of dirs in events/ftrace
That's quite a lot, so we'd better defer memory allocation util
it's needed, that's when filter is used.
Signed-off-by: Li Zefan <lizf@cn.fujitsu.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Tom Zanussi <tzanussi@gmail.com>
Cc: Masami Hiramatsu <mhiramat@redhat.com>
LKML-Reference: <4A9B8EA5.6020700@cn.fujitsu.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This patch fixes the wrong headphone output routing for MacBookPro 3,1/4,1
quirk with ALC889A codec, which caused the silent headphone output.
Also, this gives the individual Headphone and Speaker volume controls.
Reference: kernel bug#14078
http://bugzilla.kernel.org/show_bug.cgi?id=14078
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Cc: <stable@kernel.org>
In patch_vt1708(), the check of MUX nids is missing and this results in
the -EINVAL error in accessing Input Source mixer element. Simpliy
adding the call of get_mux_nids() fixes the problem.
Reference: Novell bnc#534904
https://bugzilla.novell.com/show_bug.cgi?id=534904
Signed-off-by: Takashi Iwai <tiwai@suse.de>
To unsubscribe from this list: send the line "unsubscribe linux-media" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
We should call em28xx_ir_init(dev) only when disable_ir is true.
Signed-off-by: Shine Liu <shinel@foxmail.com>
Reviewed-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The order of indexes is reversed
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Antoine Jacquet <royale@zerezo.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
[mchehab@redhat.com: fix merge conflict and a few CodingStyle issues]
Signed-off-by: Steve Gotthardt <gotthardt@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
