Commit Graph

92 Commits

Author SHA1 Message Date
Maciej Sosnowski 7f1b358a23 I/OAT: I/OAT version 3.0 support
This patch adds to ioatdma and dca modules
support for Intel I/OAT DMA engine ver.3 (aka CB3 device).
The main features of I/OAT ver.3 are:
 * 8 single channel DMA devices (8 channels total)
 * 8 DCA providers, each can accept 2 requesters
 * 8-bit TAG values and 32-bit extended APIC IDs

Signed-off-by: Maciej Sosnowski <maciej.sosnowski@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2008-07-22 17:30:57 -07:00
Maciej Sosnowski 16a37acaaf I/OAT: tcp_dma_copybreak default value dependent on I/OAT version
I/OAT DMA performance tuning showed different optimal values of
tcp_dma_copybreak for different I/OAT versions (4096 for 1.2 and 2048
for 2.0).  This patch lets ioatdma driver set tcp_dma_copybreak value
according to these results.

[dan.j.williams@intel.com: remove some ifdefs]
Signed-off-by: Maciej Sosnowski <maciej.sosnowski@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2008-07-22 17:30:57 -07:00
Maciej Sosnowski 09177e85d6 I/OAT: Add watchdog/reset functionality to ioatdma
Due to occasional DMA channel hangs observed for I/OAT versions 1.2 and 2.0
a watchdog has been introduced to check every 2 seconds
if all channels progress normally.
If stuck channel is detected, driver resets it.
The reset is done in two parts. The second part is scheduled
by the first one to reinitialize the channel after the restart.

Signed-off-by: Maciej Sosnowski <maciej.sosnowski@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2008-07-22 10:07:33 -07:00
Dan Williams 5eb907aaaf iop_adma: document how to calculate the minimum descriptor pool size
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2008-07-17 17:59:56 -07:00
Dan Williams c7141d005a iop_adma: directly reclaim descriptors on allocation failure
Force callers that trigger an "out of descriptors" condition to run the
cleanup loop directly.  Alleviates the requirement to have soft-irqs
enabled when polling for a descriptor in async_xor.

Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2008-07-17 17:59:56 -07:00
Haavard Skinnemoen 3bfb1d20b5 dmaengine: Driver for the Synopsys DesignWare DMA controller
This adds a driver for the Synopsys DesignWare DMA controller (aka
DMACA on AVR32 systems.) This DMA controller can be found integrated
on the AT32AP7000 chip and is primarily meant for peripheral DMA
transfer, but can also be used for memory-to-memory transfers.

This patch is based on a driver from David Brownell which was based on
an older version of the DMA Engine framework. It also implements the
proposed extensions to the DMA Engine API for slave DMA operations.

The dmatest client shows no problems, but there may still be room for
improvement performance-wise. DMA slave transfer performance is
definitely "good enough"; reading 100 MiB from an SD card running at ~20
MHz yields ~7.2 MiB/s average transfer rate.

Full documentation for this controller can be found in the Synopsys
DW AHB DMAC Databook:

http://www.synopsys.com/designware/docs/iip/DW_ahb_dmac/latest/doc/dw_ahb_dmac_db.pdf

The controller has lots of implementation options, so it's usually a
good idea to check the data sheet of the chip it's intergrated on as
well. The AT32AP7000 data sheet can be found here:

http://www.atmel.com/dyn/products/datasheets.asp?family_id=682


Changes since v4:
  * Use client_count instead of dma_chan_is_in_use()
  * Add missing include
  * Unmap buffers unless client told us not to

Changes since v3:
  * Update to latest DMA engine and DMA slave APIs
  * Embed the hw descriptor into the sw descriptor
  * Clean up and update MODULE_DESCRIPTION, copyright date, etc.

Changes since v2:
  * Dequeue all pending transfers in terminate_all()
  * Rename dw_dmac.h -> dw_dmac_regs.h
  * Define and use controller-specific dma_slave data
  * Fix up a few outdated comments
  * Define hardware registers as structs (doesn't generate better
    code, unfortunately, but it looks nicer.)
  * Get number of channels from platform_data instead of hardcoding it
    based on CONFIG_WHATEVER_CPU.
  * Give slave clients exclusive access to the channel

Acked-by: Maciej Sosnowski <maciej.sosnowski@intel.com>,
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2008-07-08 11:59:42 -07:00
Haavard Skinnemoen dc0ee6435c dmaengine: Add slave DMA interface
This patch adds the necessary interfaces to the DMA Engine framework
to use functionality found on most embedded DMA controllers: DMA from
and to I/O registers with hardware handshaking.

In this context, hardware hanshaking means that the peripheral that
owns the I/O registers in question is able to tell the DMA controller
when more data is available for reading, or when there is room for
more data to be written. This usually happens internally on the chip,
but these signals may also be exported outside the chip for things
like IDE DMA, etc.

A new struct dma_slave is introduced. This contains information that
the DMA engine driver needs to set up slave transfers to and from a
slave device. Most engines supporting DMA slave transfers will want to
extend this structure with controller-specific parameters.  This
additional information is usually passed from the platform/board code
through the client driver.

A "slave" pointer is added to the dma_client struct. This must point
to a valid dma_slave structure iff the DMA_SLAVE capability is
requested.  The DMA engine driver may use this information in its
device_alloc_chan_resources hook to configure the DMA controller for
slave transfers from and to the given slave device.

A new operation for preparing slave DMA transfers is added to struct
dma_device. This takes a scatterlist and returns a single descriptor
representing the whole transfer.

Another new operation for terminating all pending transfers is added as
well. The latter is needed because there may be errors outside the scope
of the DMA Engine framework that may require DMA operations to be
terminated prematurely.

DMA Engine drivers may extend the dma_device, dma_chan and/or
dma_slave_descriptor structures to allow controller-specific
operations. The client driver can detect such extensions by looking at
the DMA Engine's struct device, or it can request a specific DMA
Engine device by setting the dma_dev field in struct dma_slave.

dmaslave interface changes since v4:
  * Fix checkpatch errors
  * Fix changelog (there are no slave descriptors anymore)

dmaslave interface changes since v3:
  * Use dma_data_direction instead of a new enum
  * Submit slave transfers as scatterlists
  * Remove the DMA slave descriptor struct

dmaslave interface changes since v2:
  * Add a dma_dev field to struct dma_slave. If set, the client can
    only be bound to the DMA controller that corresponds to this
    device.  This allows controller-specific extensions of the
    dma_slave structure; if the device matches, the controller may
    safely assume its extensions are present.
  * Move reg_width into struct dma_slave as there are currently no
    users that need to be able to set the width on a per-transfer
    basis.

dmaslave interface changes since v1:
  * Drop the set_direction and set_width descriptor hooks. Pass the
    direction and width to the prep function instead.
  * Declare a dma_slave struct with fixed information about a slave,
    i.e. register addresses, handshake interfaces and such.
  * Add pointer to a dma_slave struct to dma_client. Can be NULL if
    the DMA_SLAVE capability isn't requested.
  * Drop the set_slave device hook since the alloc_chan_resources hook
    now has enough information to set up the channel for slave
    transfers.

Acked-by: Maciej Sosnowski <maciej.sosnowski@intel.com>
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2008-07-08 11:59:35 -07:00
Dan Williams e1d181efb1 dmaengine: add DMA_COMPL_SKIP_{SRC,DEST}_UNMAP flags to control dma unmap
In some cases client code may need the dma-driver to skip the unmap of source
and/or destination buffers.  Setting these flags indicates to the driver to
skip the unmap step.  In this regard async_xor is currently broken in that it
allows the destination buffer to be unmapped while an operation is still in
progress, i.e. when the number of sources exceeds the hardware channel's
maximum (fixed in a subsequent patch).

Acked-by: Saeed Bishara <saeed@marvell.com>
Acked-by: Maciej Sosnowski <maciej.sosnowski@intel.com>
Acked-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2008-07-08 11:59:12 -07:00
Haavard Skinnemoen 848c536a37 dmaengine: Add dma_client parameter to device_alloc_chan_resources
A DMA controller capable of doing slave transfers may need to know a
few things about the slave when preparing the channel. We don't want
to add this information to struct dma_channel since the channel hasn't
yet been bound to a client at this point.

Instead, pass a reference to the client requesting the channel to the
driver's device_alloc_chan_resources hook so that it can pick the
necessary information from the dma_client struct by itself.

[dan.j.williams@intel.com: fixed up fsldma and mv_xor]
Acked-by: Maciej Sosnowski <maciej.sosnowski@intel.com>
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2008-07-08 11:58:58 -07:00
Haavard Skinnemoen 4a776f0aa9 dmatest: Simple DMA memcpy test client
This client tests DMA memcpy using various lengths and various offsets
into the source and destination buffers. It will initialize both
buffers with a repeatable pattern and verify that the DMA engine copies
the requested region and nothing more. It will also verify that the
bytes aren't swapped around, and that the source buffer isn't modified.

The dmatest module can be configured to test a specific device, a
specific channel. It can also test multiple channels at the same time,
and it can start multiple threads competing for the same channel.

Changes since v2:
  * Support testing multiple channels at the same time
  * Support testing with multiple threads competing for the same channel
  * Use counting test patterns in order to catch byte ordering issues

Changes since v1:
  * Remove extra dashes around "help"
  * Remove "default n" from Kconfig
  * Turn TEST_BUF_SIZE into a module parameter
  * Return DMA_NAK instead of DMA_DUP
  * Print unhandled events
  * Support testing specific channels and devices
  * Move to the end of the Makefile

Acked-by: Maciej Sosnowski <maciej.sosnowski@intel.com>
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2008-07-08 11:58:45 -07:00
Saeed Bishara ff7b04796d dmaengine: DMA engine driver for Marvell XOR engine
The XOR engine found in Marvell's SoCs and system controllers
provides XOR and DMA operation, iSCSI CRC32C calculation, memory
initialization, and memory ECC error cleanup operation support.

This driver implements the DMA engine API and supports the following
capabilities:
- memcpy
- xor
- memset

The XOR engine can be used by DMA engine clients implemented in the
kernel, one of those clients is the RAID module.  In that case, I
observed 20% improvement in the raid5 write throughput, and 40%
decrease in the CPU utilization when doing array construction, those
results obtained on an 5182 running at 500Mhz.

When enabling the NET DMA client, the performance decreased, so
meanwhile it is recommended to keep this client off.

Signed-off-by: Saeed Bishara <saeed@marvell.com>
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: Nicolas Pitre <nico@marvell.com>
Acked-by: Maciej Sosnowski <maciej.sosnowski@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2008-07-08 11:58:36 -07:00
Kay Sievers ebabe27626 iop-adma: fix platform driver hotplug/coldplug
Since 43cc71eed1, the platform
modalias is prefixed with "platform:". Add MODULE_ALIAS() to most
of the hotpluggable platform drivers, to re-enable auto loading.

Cc: <stable@kernel.org>
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2008-07-08 11:58:28 -07:00
Dan Williams 7cc5bf9a3a dmaengine: track the number of clients using a channel
Haavard's dma-slave interface would like to test for exclusive access to a
channel.  The standard channel refcounting is not sufficient in that it
tracks more than just client references, it is also inaccurate as reference
counts are percpu until the channel is removed.

This change also enables a future fix to deallocate resources when a client
declines to use a capable channel.

Acked-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2008-07-08 11:58:21 -07:00
Dan Williams 9c402f4e19 dmaengine: remove arch dependency from DMADEVICES
The dependency is redundant since all drivers set their specific arch
dependencies.  The NET_DMA option is modified to be enabled only on platforms
where it is known to have a positive effect.  HAS_DMA is added as an explicit
dependency for the DMADEVICES menu.

Acked-by: Adrian Bunk <bunk@kernel.org>
Acked-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2008-07-08 11:58:12 -07:00
Haavard Skinnemoen 1099dc7924 dmaengine: Couple DMA channels to their physical DMA device
Set the 'parent' field of channel class devices to point to the
physical DMA device initialized by the DMA engine driver.

This allows drivers to use chan->dev.parent for syncing DMA buffers
and adds a 'device' symlink to the real device in
/sys/class/dma/dmaXchanY.

Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2008-07-08 11:58:05 -07:00
Li Yang 51ee87f27a fsldma: fix incorrect exit path for initialization
Signed-off-by: Li Yang <leoli@freescale.com>
Acked-by: Zhang Wei <zw@zh-kernel.org>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2008-07-08 11:57:45 -07:00
Christophe Jaillet eccf2144e1 iop-adma: fixup some kzalloc/memset confusions
1) Remove an explicit memset(.., 0, ...) to a variable allocated with
kzalloc (i.e. 'dest').

2) Allocate 'src' with kmalloc instead of kzalloc as all elements of the
'src' buffer are initialized in a 'for(...)' loop just after.

3) remove useless 'sizeof(u8)', which always returns 1, when computing the
size of the memory to be allocated.

Signed-off-by: Christophe Jaillet <christophe.jaillet@wanadoo.fr>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2008-05-20 13:51:20 -07:00
Sebastian Siewior 8a5703f846 DMA engine: typo fixes
Spelling fixes for dmaengine.[ch]

Signed-off-by: Sebastian Siewior <bigeasy@linutronix.de>
Acked-by: Maciej Sosnowski <maciej.sosnowski@intel.com>
Signed-off-by: Jesper Juhl <jesper.juhl@gmail.com>
2008-04-21 22:38:45 +00:00
Dan Williams 636bdeaa12 dmaengine: ack to flags: make use of the unused bits in the 'ack' field
'ack' is currently a simple integer that flags whether or not a client is done
touching fields in the given descriptor.  It is effectively just a single bit
of information.  Converting this to a flags parameter allows the other bits to
be put to use to control completion actions, like dma-unmap, and capture
results, like xor-zero-sum == 0.

Changes are one of:
1/ convert all open-coded ->ack manipulations to use async_tx_ack
   and async_tx_test_ack.
2/ set the ack bit at prep time where possible
3/ make drivers store the flags at prep time
4/ add flags to the device_prep_dma_interrupt prototype

Acked-by: Maciej Sosnowski <maciej.sosnowski@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2008-04-17 13:25:54 -07:00
Dan Williams c4fe15541d iop-adma: remove the workaround for missed interrupts on iop3xx
This workaround was covering the dependency submission bug in async_tx.

Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2008-04-17 13:25:54 -07:00
Dan Williams ce4d65a5db async_tx: kill ->device_dependency_added
DMA drivers no longer need to be notified of dependency submission
events as async_tx_run_dependencies and async_tx_channel_switch will
handle the scheduling and execution of dependent operations.

[sfr@canb.auug.org.au: extend this for fsldma]
Acked-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2008-04-17 13:25:54 -07:00
Dan Williams 19242d7233 async_tx: fix multiple dependency submission
Shrink struct dma_async_tx_descriptor and introduce
async_tx_channel_switch to properly inject a channel switch interrupt in
the descriptor stream.  This simplifies the locking model as drivers no
longer need to handle dma_async_tx_descriptor.lock.

Acked-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2008-04-17 13:25:05 -07:00
Zhang Wei 1c62979ed2 fsldma: Split the MPC83xx event from MPC85xx and refine irq codes.
Split MPC83xx EOCDI event from MPC85xx EOLNI event, which is
also need to update cookie and start the next transfer.
The DMA channel irq handler function code is refined.
The patch is tested on MPC8377MDS board.

Signed-off-by: Zhang Wei <wei.zhang@freescale.com>
Signed-off-by; Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2008-04-17 13:22:16 -07:00
Zhang Wei 411e23dbe9 fsldma: Remove CONFIG_FSL_DMA_SELFTEST, keep fsl_dma_self_test() running always.
Always enabling the fsl_dma_self_test() to ensure the DMA controller
should works well after the driver probed.

Signed-off-by: Zhang Wei <wei.zhang@freescale.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2008-04-17 13:22:15 -07:00
Kumar Gala 049c9d4553 [POWERPC] fsldma: Use compatiable binding as spec
Documentation/powerpc/booting-without-of.txt specifies the
compatiables we should bind to for this driver (elo, eloplus).
Use these instead of the extremely specific 'mpc8540' and 'mpc8349'
compatiables.

Acked-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2008-03-31 11:45:41 -05:00
Al Viro a4e6d5d381 fix the broken annotations in fsldma
a) every bitwise declaration will give a unique type; use typedefs.

 b) no need to bother with the stuff pointed to by iomem pointers,
    unless it's accessed directly.  noderef will force us to use helpers
    anyway.

Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-03-30 14:20:24 -07:00
Al Viro 53a0c98e11 ioat_dca __iomem annotations
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-03-30 14:18:41 -07:00
Zhang Wei f79abb627f fsldma: Fix the DMA halt when using DMA_INTERRUPT async_tx transfer.
The DMA_INTERRUPT async_tx is a NULL transfer, thus the BCR(count register)
is 0. When the transfer started with a byte count of zero, the DMA
controller will triger a PE(programming error) event and halt, not a normal
interrupt. I add special codes for PE event and DMA_INTERRUPT
async_tx testing.

Signed-off-by: Zhang Wei <wei.zhang@freescale.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2008-03-18 17:00:59 -07:00
Harvey Harrison 3d9b525b69 iop-adma.c: replace remaining __FUNCTION__ occurrences
__FUNCTION__ is gcc-specific, use __func__

Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2008-03-13 10:57:09 -07:00
Zhang Wei 9c98718e73 fsldma: Add a completed cookie updated action in DMA finish interrupt.
The patch 'fsldma: do not cleanup descriptors in hardirq context'
(commit 222ccf9ab8) removed descriptors
cleanup function to tasklet but the completed cookie do not updated.
Thus, the DMA controller will get lots of duplicated transfer
interrupts. Just make a completed cookie update in interrupt handler.
And keep other cleanup jobs in tasklet function.

Tested-by: Sebastian Siewior <bigeasy@linutronix.de>
Signed-off-by: Zhang Wei <wei.zhang@freescale.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2008-03-13 10:57:09 -07:00
Zhang Wei 2187c269ad fsldma: Add device_prep_dma_interrupt support to fsldma.c
This is a bug that I assigned DMA_INTERRUPT capability to fsldma
but missing device_prep_dma_interrupt function. For a bug in
dmaengine.c the driver passed BUG_ON() checking. The patch fixes it.

Signed-off-by: Zhang Wei <wei.zhang@freescale.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2008-03-13 10:57:08 -07:00
Zhang Wei 9b941c6660 dmaengine: Fix a bug about BUG_ON() on DMA engine capability DMA_INTERRUPT.
The device->device_prep_dma_interrupt function is used by
DMA_INTERRUPT capability, not DMA_ZERO_SUM.

Signed-off-by: Zhang Wei <wei.zhang@freescale.com>
Acked-by: Maciej Sosnowski <maciej.sosnowski@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2008-03-13 10:57:07 -07:00
Zhang Wei 56822843ff fsldma: Fix fsldma.c warning messages when it's compiled under PPC64.
There are warning messages reported by Stephen Rothwell with
ARCH=powerpc allmodconfig build:

drivers/dma/fsldma.c: In function 'fsl_dma_prep_memcpy':
drivers/dma/fsldma.c:439: warning: comparison of distinct pointer types
lacks a cast
drivers/dma/fsldma.c: In function 'fsl_chan_xfer_ld_queue':
drivers/dma/fsldma.c:584: warning: format '%016llx' expects type 'long long
unsigned int', but argument 4 has type 'dma_addr_t'
drivers/dma/fsldma.c: In function 'fsl_dma_chan_do_interrupt':
drivers/dma/fsldma.c:668: warning: format '%x' expects type 'unsigned int',
but argument 5 has type 'dma_addr_t'
drivers/dma/fsldma.c:684: warning: format '%016llx' expects type 'long long
unsigned int', but argument 4 has type 'dma_addr_t'
drivers/dma/fsldma.c:684: warning: format '%016llx' expects type 'long long
unsigned int', but argument 5 has type 'dma_addr_t'
drivers/dma/fsldma.c:701: warning: format '%02x' expects type 'unsigned
int', but argument 4 has type 'dma_addr_t'
drivers/dma/fsldma.c: In function 'fsl_dma_self_test':
drivers/dma/fsldma.c:840: warning: format '%d' expects type 'int', but
argument 5 has type 'size_t'
drivers/dma/fsldma.c: In function 'of_fsl_dma_probe':
drivers/dma/fsldma.c:1010: warning: format '%08x' expects type 'unsigned
int', but argument 5 has type 'resource_size_t'

This patch fixed the above warning messages.

Signed-off-by: Zhang Wei <wei.zhang@freescale.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2008-03-13 10:57:07 -07:00
Dan Williams 6497dcffe0 ioat: fix 'ack' handling, driver must ensure that 'ack' is zero
Initialize 'ack' to zero in case the descriptor has been recycled.

Prevents "kernel BUG at crypto/async_tx/async_xor.c:185!"

Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Acked-by: Shannon Nelson <shannon.nelson@intel.com>
Cc: stable@kernel.org
2008-03-04 10:16:46 -07:00
Dan Williams 222ccf9ab8 fsldma: do not cleanup descriptors in hardirq context
"Cleaning" descriptors involves calling pending callbacks and clients
assume that their callback will only ever happen in softirq context.
Delay cleanup to the tasklet.

Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Acked-by: Zhang Wei <wei.zhang@freescale.com>
2008-03-04 10:16:46 -07:00
Zhang Wei 173acc7ce8 dmaengine: add driver for Freescale MPC85xx DMA controller
The driver implements DMA engine API for Freescale MPC85xx DMA controller,
which could be used by devices in the silicon.  The driver supports the
Basic mode of Freescale MPC85xx DMA controller.  The MPC85xx processors
supported include MPC8540/60, MPC8555, MPC8548, MPC8641 and so on.

The MPC83xx(MPC8349, MPC8360) are also supported.

[kamalesh@linux.vnet.ibm.com: build fix]
[dan.j.williams@intel.com: merge mm fixes, rebase on async_tx-2.6.25]
Signed-off-by: Zhang Wei <wei.zhang@freescale.com>
Signed-off-by: Ebony Zhu <ebony.zhu@freescale.com>
Acked-by: Kumar Gala <galak@gate.crashing.org>
Cc: Shannon Nelson <shannon.nelson@intel.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2008-03-04 10:16:46 -07:00
Dan Williams d4c56f97ff async_tx: replace 'int_en' with operation preparation flags
Pass a full set of flags to drivers' per-operation 'prep' routines.
Currently the only flag passed is DMA_PREP_INTERRUPT.  The expectation is
that arch-specific async_tx_find_channel() implementations can exploit this
capability to find the best channel for an operation.

Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Acked-by: Shannon Nelson <shannon.nelson@intel.com>
Reviewed-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
2008-02-06 10:12:18 -07:00
Dan Williams 0036731c88 async_tx: kill tx_set_src and tx_set_dest methods
The tx_set_src and tx_set_dest methods were originally implemented to allow
an array of addresses to be passed down from async_xor to the dmaengine
driver while minimizing stack overhead.  Removing these methods allows
drivers to have all transaction parameters available at 'prep' time, saves
two function pointers in struct dma_async_tx_descriptor, and reduces the
number of indirect branches..

A consequence of moving this data to the 'prep' routine is that
multi-source routines like async_xor need temporary storage to convert an
array of linear addresses into an array of dma addresses.  In order to keep
the same stack footprint of the previous implementation the input array is
reused as storage for the dma addresses.  This requires that
sizeof(dma_addr_t) be less than or equal to sizeof(void *).  As a
consequence CONFIG_DMADEVICES now depends on !CONFIG_HIGHMEM64G.  It also
requires that drivers be able to make descriptor resources available when
the 'prep' routine is polled.

Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Acked-by: Shannon Nelson <shannon.nelson@intel.com>
2008-02-06 10:12:17 -07:00
Denis Cheng e73ef9acfd iop-adma: use LIST_HEAD instead of LIST_HEAD_INIT
these three list_head are all local variables, but can also use LIST_HEAD.

Signed-off-by: Denis Cheng <crquan@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2008-02-06 10:12:17 -07:00
Tony Jones 891f78ea83 DMA: Convert from class_device to device for DMA engine
Signed-off-by: Tony Jones <tonyj@suse.de>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Cc: Shannon Nelson <shannon.nelson@intel.com>
Cc: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2008-01-24 20:40:05 -08:00
Shannon Nelson bb8e8bcce7 I/OAT: fix null device in call to dev_err()
We can't use the device in a dev_err() after a kzalloc failure or after the
kfree, so simplify it to the pdev that was originally passed in.

Cc: Eric Sesterhenn <snakebyte@gmx.de>
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-12-17 19:28:17 -08:00
Shannon Nelson 711924b105 I/OAT: fixups from code comments
A few fixups from Andrew's code comments.
  - removed "static inline" forward-declares
  - changed use of min() to min_t()
  - removed some unnecessary NULL initializations
  - removed a couple of BUG() calls

Fixes this:

drivers/dma/ioat_dma.c: In function `ioat1_tx_submit':
drivers/dma/ioat_dma.c:177: sorry, unimplemented: inlining failed in call to '__ioat1_dma_memcpy_issue_pending': function body not available
drivers/dma/ioat_dma.c:268: sorry, unimplemented: called from here

Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Cc: "Williams, Dan J" <dan.j.williams@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-12-17 19:28:17 -08:00
Haavard Skinnemoen 6d4f5879b6 dmaengine: correct invalid assumptions in the Kconfig text
This patch corrects recently changed (and now invalid) Kconfig descriptions
for the DMA engine framework:

 - Non-Intel(R) hardware also has DMA engines;
 - DMA is used for more than memcpy and RAID offloading.

In fact, on most platforms memcpy and RAID aren't factors, and DMA
exists so that peripherals can transfer data to/from memory while
the CPU does other work.

Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-11-29 09:24:53 -08:00
Shannon Nelson 7bb67c14fd I/OAT: Add support for version 2 of ioatdma device
Add support for version 2 of the ioatdma device.  This device handles
the descriptor chain and DCA services slightly differently:
 - Instead of moving the dma descriptors between a busy and an idle chain,
   this new version uses a single circular chain so that we don't have
   rewrite the next_descriptor pointers as we add new requests, and the
   device doesn't need to re-read the last descriptor.
 - The new device has the DCA tags defined internally instead of needing
   them defined statically.

Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Cc: "Williams, Dan J" <dan.j.williams@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-11-14 18:45:41 -08:00
Haavard Skinnemoen 348badf1e8 dmaengine: fix broken device refcounting
When a DMA device is unregistered, its reference count is decremented twice
for each channel: Once dma_class_dev_release() and once in
dma_chan_cleanup().  This may result in the DMA device driver's remove()
function completing before all channels have been cleaned up, causing lots
of use-after-free fun.

Fix it by incrementing the device's reference count twice for each
channel during registration.

[dan.j.williams@intel.com: kill unnecessary client refcounting]
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-11-14 18:45:39 -08:00
Andi Kleen 4138f08d1c Remove bogus default y for DMAR and NET_DMA
No reason I can think of of making them default y Most people don't have
the hardware and with default y they just pollute lots of configs during
make oldconfig.

Signed-off-by: Andi Kleen <ak@suse.de>
Acked-by: Jeff Garzik <jeff@garzik.org>
Acked-by: "Nelson, Shannon" <shannon.nelson@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-10-30 08:06:55 -07:00
Shannon Nelson 952184304f I/OAT: Add completion callback for async_tx interface use
The async_tx interface includes a completion callback.  This adds support
for using that callback, including using interrupts on completion.

[akpm@linux-foundation.org: various fixes]
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-10-18 14:37:32 -07:00
Shannon Nelson 7f2b291f56 I/OAT: Tighten descriptor setup performance
The change to the async_tx interface cost this driver some performance by
spreading the descriptor setup across several functions, including multiple
passes over the new descriptor chain.  Here we bring the work back into one
primary function and only do one pass.

[akpm@linux-foundation.org: cleanups, uninline]
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-10-18 14:37:32 -07:00
Shannon Nelson 5149fd010f I/OAT: clean up error handling and some print messages
Make better use of dev_err(), and catch an error where the transaction
creation might fail.

Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-10-18 14:37:32 -07:00
Shannon Nelson dfe2299e7b I/OAT: clean up of dca provider start and stop
Don't start ioat_dca if ioat_dma didn't start, and then stop ioat_dca
before stopping ioat_dma.  Since the ioat_dma side does the pci device
work, This takes care of ioat_dca trying to use a bad device reference.

Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-10-18 14:37:32 -07:00