* 'perf-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
perf evlist: Fix per thread mmap setup
perf tools: Honour the cpu list parameter when also monitoring a thread list
kprobes, x86: Disable irqs during optimized callback
Trying to enable the local APIC timer on early K8 revisions
uncovers a number of other issues with it, in conjunction with
the C1E enter path on AMD. Fixing those causes much more churn
and troubles than the benefit of using that timer brings so
don't enable it on K8 at all, falling back to the original
functionality the kernel had wrt to that.
Reported-and-bisected-by: Nick Bowler <nbowler@elliptictech.com>
Cc: Boris Ostrovsky <Boris.Ostrovsky@amd.com>
Cc: Andreas Herrmann <andreas.herrmann3@amd.com>
Cc: Greg Kroah-Hartman <greg@kroah.com>
Cc: Hans Rosenfeld <hans.rosenfeld@amd.com>
Cc: Nick Bowler <nbowler@elliptictech.com>
Cc: Joerg-Volker-Peetz <jvpeetz@web.de>
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
Link: http://lkml.kernel.org/r/1305636919-31165-3-git-send-email-bp@amd64.org
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This reverts commit e20a2d205c, as it crashes
certain boxes with specific AMD CPU models.
Moving the lower endpoint of the Erratum 400 check to accomodate
earlier K8 revisions (A-E) opens a can of worms which is simply
not worth to fix properly by tweaking the errata checking
framework:
* missing IntPenging MSR on revisions < CG cause #GP:
http://marc.info/?l=linux-kernel&m=130541471818831
* makes earlier revisions use the LAPIC timer instead of the C1E
idle routine which switches to HPET, thus not waking up in
deeper C-states:
http://lkml.org/lkml/2011/4/24/20
Therefore, leave the original boundary starting with K8-revF.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This patch fixes a bug reported by a customer, who found
that many unreasonable error interrupts reported on all
non-boot CPUs (APs) during the system boot stage.
According to Chapter 10 of Intel Software Developer Manual
Volume 3A, Local APIC may signal an illegal vector error when
an LVT entry is set as an illegal vector value (0~15) under
FIXED delivery mode (bits 8-11 is 0), regardless of whether
the mask bit is set or an interrupt actually happen. These
errors are seen as error interrupts.
The initial value of thermal LVT entries on all APs always reads
0x10000 because APs are woken up by BSP issuing INIT-SIPI-SIPI
sequence to them and LVT registers are reset to 0s except for
the mask bits which are set to 1s when APs receive INIT IPI.
When the BIOS takes over the thermal throttling interrupt,
the LVT thermal deliver mode should be SMI and it is required
from the kernel to keep AP's LVT thermal monitoring register
programmed as such as well.
This issue happens when BIOS does not take over thermal throttling
interrupt, AP's LVT thermal monitor register will be restored to
0x10000 which means vector 0 and fixed deliver mode, so all APs will
signal illegal vector error interrupts.
This patch check if interrupt delivery mode is not fixed mode before
restoring AP's LVT thermal monitor register.
Signed-off-by: Youquan Song <youquan.song@intel.com>
Acked-by: Suresh Siddha <suresh.b.siddha@intel.com>
Acked-by: Yong Wang <yong.y.wang@intel.com>
Cc: hpa@linux.intel.com
Cc: joe@perches.com
Cc: jbaron@redhat.com
Cc: trenn@suse.de
Cc: kent.liu@intel.com
Cc: chaohong.guo@intel.com
Cc: <stable@kernel.org> # As far back as possible
Link: http://lkml.kernel.org/r/1303402963-17738-1-git-send-email-youquan.song@intel.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>
b may be added to a list, but is not removed before being freed
in the case of an error. This is done in the corresponding
deallocation function, so the code here has been changed to
follow that.
The sematic match that finds this problem is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@@
expression E,E1,E2;
identifier l;
@@
*list_add(&E->l,E1);
... when != E1
when != list_del(&E->l)
when != list_del_init(&E->l)
when != E = E2
*kfree(E);// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Cc: Borislav Petkov <borislav.petkov@amd.com>
Cc: Robert Richter <robert.richter@amd.com>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Andreas Herrmann <andreas.herrmann3@amd.com>
Cc: <stable@kernel.org>
Link: http://lkml.kernel.org/r/1305294731-12127-1-git-send-email-julia@diku.dk
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This is a fix for the SGI Altix-UV Broadcast Assist Unit code,
which is used for TLB flushing.
Certain hardware configurations (that customers are ordering)
cause nasids (numa address space id's) to be non-consecutive.
Specifically, once you have more than 4 blades in a IRU
(Individual Rack Unit - or 1/2 rack) but less than the maximum
of 16, the nasid numbering becomes non-consecutive. This
currently results in a 'catastrophic error' (CATERR) detected by
the firmware during OS boot. The BAU is generating an 'INTD'
request that is targeting a non-existent nasid value. Such
configurations may also occur when a blade is configured off
because of hardware errors. (There is one UV hub per blade.)
This patch is required to support such configurations.
The problem with the tlb_uv.c code is that is using the
consecutive hub numbers as indices to the BAU distribution bit
map. These are simply the ordinal position of the hub or blade
within its partition. It should be using physical node numbers
(pnodes), which correspond to the physical nasid values. Use of
the hub number only works as long as the nasids in the partition
are consecutive and increase with a stride of 1.
This patch changes the index to be the pnode number, thus
allowing nasids to be non-consecutive.
It also provides a table in local memory for each cpu to
translate target cpu number to target pnode and nasid.
And it improves naming to properly reflect 'node' and 'uvhub'
versus 'nasid'.
Signed-off-by: Cliff Wickman <cpw@sgi.com>
Cc: <stable@kernel.org>
Link: http://lkml.kernel.org/r/E1QJmxX-0002Mz-Fk@eag09.americas.sgi.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>
With CONFIG_DEBUG_SECTION_MISMATCH=y I see these warnings in next-20110415:
LD vmlinux.o
MODPOST vmlinux.o
WARNING: vmlinux.o(.text+0x1ba48): Section mismatch in reference from the function native_pagetable_reserve() to the function .init.text:memblock_x86_reserve_range()
The function native_pagetable_reserve() references
the function __init memblock_x86_reserve_range().
This is often because native_pagetable_reserve lacks a __init
annotation or the annotation of memblock_x86_reserve_range is wrong.
This patch fixes the issue.
Thanks to pipacs from PaX project for help on IRC.
Acked-by: "H. Peter Anvin" <hpa@zytor.com>
Signed-off-by: Sedat Dilek <sedat.dilek@gmail.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Introduce a new x86_init hook called pagetable_reserve that at the end
of init_memory_mapping is used to reserve a range of memory addresses for
the kernel pagetable pages we used and free the other ones.
On native it just calls memblock_x86_reserve_range while on xen it also
takes care of setting the spare memory previously allocated
for kernel pagetable pages from RO to RW, so that it can be used for
other purposes.
A detailed explanation of the reason why this hook is needed follows.
As a consequence of the commit:
commit 4b239f458c
Author: Yinghai Lu <yinghai@kernel.org>
Date: Fri Dec 17 16:58:28 2010 -0800
x86-64, mm: Put early page table high
at some point init_memory_mapping is going to reach the pagetable pages
area and map those pages too (mapping them as normal memory that falls
in the range of addresses passed to init_memory_mapping as argument).
Some of those pages are already pagetable pages (they are in the range
pgt_buf_start-pgt_buf_end) therefore they are going to be mapped RO and
everything is fine.
Some of these pages are not pagetable pages yet (they fall in the range
pgt_buf_end-pgt_buf_top; for example the page at pgt_buf_end) so they
are going to be mapped RW. When these pages become pagetable pages and
are hooked into the pagetable, xen will find that the guest has already
a RW mapping of them somewhere and fail the operation.
The reason Xen requires pagetables to be RO is that the hypervisor needs
to verify that the pagetables are valid before using them. The validation
operations are called "pinning" (more details in arch/x86/xen/mmu.c).
In order to fix the issue we mark all the pages in the entire range
pgt_buf_start-pgt_buf_top as RO, however when the pagetable allocation
is completed only the range pgt_buf_start-pgt_buf_end is reserved by
init_memory_mapping. Hence the kernel is going to crash as soon as one
of the pages in the range pgt_buf_end-pgt_buf_top is reused (b/c those
ranges are RO).
For this reason we need a hook to reserve the kernel pagetable pages we
used and free the other ones so that they can be reused for other
purposes.
On native it just means calling memblock_x86_reserve_range, on Xen it
also means marking RW the pagetable pages that we allocated before but
that haven't been used before.
Another way to fix this is without using the hook is by adding a 'if
(xen_pv_domain)' in the 'init_memory_mapping' code and calling the Xen
counterpart, but that is just nasty.
Signed-off-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
Acked-by: Yinghai Lu <yinghai@kernel.org>
Acked-by: H. Peter Anvin <hpa@zytor.com>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Disable irqs during optimized callback, so we dont miss any in-irq kprobes.
The following commands:
# cd /debug/tracing/
# echo "p mutex_unlock" >> kprobe_events
# echo "p _raw_spin_lock" >> kprobe_events
# echo "p smp_apic_timer_interrupt" >> ./kprobe_events
# echo 1 > events/enable
Cause the optimized kprobes to be missed. None is missed
with the fix applied.
Signed-off-by: Jiri Olsa <jolsa@redhat.com>
Acked-by: Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com>
Link: http://lkml.kernel.org/r/20110511110613.GB2390@jolsa.brq.redhat.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This fixes problems seen on UV systems handling NMIs from the
node controller.
I isolated the "dazed..." messages that I saw earlier to a bug in
the BMC on our platform. It was sending NMIs w/o properly setting
a register that indicated the source of NMI.
So rather than _assuming_ any unhandled NMI came from the UV system
maintenance console (SMC), add a check to verify that the SMC actually
sent the NMI.
Signed-off-by: Jack Steiner <steiner@sgi.com>
Cc: gorcunov@gmail.com
Cc: dzickus@redhat.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>
The Intel Nehalem offcore bits implemented in:
e994d7d23a0b: perf: Fix LLC-* events on Intel Nehalem/Westmere
... are wrong: they implemented _ACCESS as _HIT and counted OTHER_CORE_HIT* as
MISS even though its clearly documented as an L3 hit ...
Fix them and the Westmere definitions as well.
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Lin Ming <ming.m.lin@intel.com>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Steven Rostedt <rostedt@goodmis.org>
Link: http://lkml.kernel.org/r/1299119690-13991-3-git-send-email-ming.m.lin@intel.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>
* 'stable/bug-fixes-for-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen:
xen: mask_rw_pte mark RO all pagetable pages up to pgt_buf_top
xen/mmu: Add workaround "x86-64, mm: Put early page table high"
The use of base for %ebx in this file is arbitrary, *except* that we
also use it to compute the real-mode segment. Therefore, make it so
that r_base really is the true address to which %ebx points.
This resolves kernel bugzilla 33302.
Reported-and-tested-by: Alexey Zaytsev <alexey.zaytsev@gmail.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Link: http://lkml.kernel.org/n/tip-08os5wi3yq1no0y4i5m4z7he@git.kernel.org
mask_rw_pte is currently checking if a pfn is a pagetable page if it
falls in the range pgt_buf_start - pgt_buf_end but that is incorrect
because pgt_buf_end is a moving target: pgt_buf_top is the real
boundary.
Acked-by: "H. Peter Anvin" <hpa@zytor.com>
Signed-off-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
As a consequence of the commit:
commit 4b239f458c
Author: Yinghai Lu <yinghai@kernel.org>
Date: Fri Dec 17 16:58:28 2010 -0800
x86-64, mm: Put early page table high
it causes the Linux kernel to crash under Xen:
mapping kernel into physical memory
Xen: setup ISA identity maps
about to get started...
(XEN) mm.c:2466:d0 Bad type (saw 7400000000000001 != exp 1000000000000000) for mfn b1d89 (pfn bacf7)
(XEN) mm.c:3027:d0 Error while pinning mfn b1d89
(XEN) traps.c:481:d0 Unhandled invalid opcode fault/trap [#6] on VCPU 0 [ec=0000]
(XEN) domain_crash_sync called from entry.S
(XEN) Domain 0 (vcpu#0) crashed on cpu#0:
...
The reason is that at some point init_memory_mapping is going to reach
the pagetable pages area and map those pages too (mapping them as normal
memory that falls in the range of addresses passed to init_memory_mapping
as argument). Some of those pages are already pagetable pages (they are
in the range pgt_buf_start-pgt_buf_end) therefore they are going to be
mapped RO and everything is fine.
Some of these pages are not pagetable pages yet (they fall in the range
pgt_buf_end-pgt_buf_top; for example the page at pgt_buf_end) so they
are going to be mapped RW. When these pages become pagetable pages and
are hooked into the pagetable, xen will find that the guest has already
a RW mapping of them somewhere and fail the operation.
The reason Xen requires pagetables to be RO is that the hypervisor needs
to verify that the pagetables are valid before using them. The validation
operations are called "pinning" (more details in arch/x86/xen/mmu.c).
In order to fix the issue we mark all the pages in the entire range
pgt_buf_start-pgt_buf_top as RO, however when the pagetable allocation
is completed only the range pgt_buf_start-pgt_buf_end is reserved by
init_memory_mapping. Hence the kernel is going to crash as soon as one
of the pages in the range pgt_buf_end-pgt_buf_top is reused (b/c those
ranges are RO).
For this reason, this function is introduced which is called _after_
the init_memory_mapping has completed (in a perfect world we would
call this function from init_memory_mapping, but lets ignore that).
Because we are called _after_ init_memory_mapping the pgt_buf_[start,
end,top] have all changed to new values (b/c another init_memory_mapping
is called). Hence, the first time we enter this function, we save
away the pgt_buf_start value and update the pgt_buf_[end,top].
When we detect that the "old" pgt_buf_start through pgt_buf_end
PFNs have been reserved (so memblock_x86_reserve_range has been called),
we immediately set out to RW the "old" pgt_buf_end through pgt_buf_top.
And then we update those "old" pgt_buf_[end|top] with the new ones
so that we can redo this on the next pagetable.
Acked-by: "H. Peter Anvin" <hpa@zytor.com>
Reviewed-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
[v1: Updated with Jeremy's comments]
[v2: Added the crash output]
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
numa_cleanup_meminfo() trims each memblk between low (0) and
high (max_pfn) limits and discards empty ones. However, the
emptiness detection incorrectly used equality test. If the
start of a memblk is higher than max_pfn, it is empty but fails
the equality test and doesn't get discarded.
The condition triggers when max_pfn is lower than start of a
NUMA node and results in memory misconfiguration - leading to
WARN_ON()s and other funnies. The bug was discovered in devel
branch where 32bit too uses this code path for NUMA init. If a
node is above the addressing limit, max_pfn ends up lower than
the node triggering this problem.
The failure hasn't been observed on x86-64 but is still possible
with broken hardware e820/NUMA info. As the fix is very low
risk, it would be better to apply it even for 64bit.
Fix it by using >= instead of ==.
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
[ Extracted the actual fix from the original patch and rewrote patch description. ]
Signed-off-by: Tejun Heo <tj@kernel.org>
Link: http://lkml.kernel.org/r/20110501171204.GO29280@htj.dyndns.org
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Older AMD K8 processors (Revisions A-E) are affected by erratum
400 (APIC timer interrupts don't occur in C states greater than
C1). This, for example, means that X86_FEATURE_ARAT flag should
not be set for these parts.
This addresses regression introduced by commit
b87cf80af3 ("x86, AMD: Set ARAT
feature on AMD processors") where the system may become
unresponsive until external interrupt (such as keyboard input)
occurs. This results, for example, in time not being reported
correctly, lack of progress on the system and other lockups.
Reported-by: Joerg-Volker Peetz <jvpeetz@web.de>
Tested-by: Joerg-Volker Peetz <jvpeetz@web.de>
Acked-by: Borislav Petkov <borislav.petkov@amd.com>
Signed-off-by: Boris Ostrovsky <Boris.Ostrovsky@amd.com>
Cc: stable@kernel.org
Link: http://lkml.kernel.org/r/1304113663-6586-1-git-send-email-ostr@amd64.org
Signed-off-by: Ingo Molnar <mingo@elte.hu>
* 'perf-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
perf, x86, nmi: Move LVT un-masking into irq handlers
perf events, x86: Work around the Nehalem AAJ80 erratum
perf, x86: Fix BTS condition
ftrace: Build without frame pointers on Microblaze
The USB and SATA ioapic interrrupt pins are configured as edge type,
but need to be level type interrupts to work correctly.
[ tglx: Split out from the combo patch ]
Cc: Torben Hohn <torbenh@linutronix.de>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Link: http://lkml.kernel.org/r/%3C20110427143052.GA15211%40linutronix.de%3E
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
We use io_apic_setup_irq_pin() in order to configure pin's interrupt
number polarity and type. This is done on every irq_create_of_mapping()
which happens for instance during pci enable calls. Level typed
interrupts are masked by default, edge are unmasked.
On the first ->xlate() call the level interrupt is configured and
masked. The driver calls request_irq() and the line is unmasked. Lets
assume the interrupt line is shared with another device and we call
pci_enable_device() for this device. The ->xlate() configures the pin
again and it is masked. request_irq() does not unmask the line because
it _is_ already unmasked according to its internal state. So the
interrupt will never be unmasked again.
This patch is based on an earlier work by Torben Hohn and solves the
problem by configuring the pin only once. Since all devices must agree
on the same type and polarity there is no point in configuring the pin
more than once.
[ tglx: Split out the ce4100 part into a separate patch ]
Cc: Torben Hohn <torbenh@linutronix.de>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Link: http://lkml.kernel.org/r/%3C20110427143052.GA15211%40linutronix.de%3E
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
It was noticed that P4 machines were generating double NMIs for
each perf event. These extra NMIs lead to 'Dazed and confused'
messages on the screen.
I tracked this down to a P4 quirk that said the overflow bit had
to be cleared before re-enabling the apic LVT mask. My first
attempt was to move the un-masking inside the perf nmi handler
from before the chipset NMI handler to after.
This broke Nehalem boxes that seem to like the unmasking before
the counters themselves are re-enabled.
In order to keep this change simple for 2.6.39, I decided to
just simply move the apic LVT un-masking to the beginning of all
the chipset NMI handlers, with the exception of Pentium4's to
fix the double NMI issue.
Later on we can move the un-masking to later in the handlers to
save a number of 'extra' NMIs on those particular chipsets.
I tested this change on a P4 machine, an AMD machine, a Nehalem
box, and a core2quad box. 'perf top' worked correctly along
with various other small 'perf record' runs. Anything high
stress breaks all the machines but that is a different problem.
Thanks to various people for testing different versions of this
patch.
Reported-and-tested-by: Shaun Ruffell <sruffell@digium.com>
Signed-off-by: Don Zickus <dzickus@redhat.com>
Cc: Cyrill Gorcunov <gorcunov@gmail.com>
Link: http://lkml.kernel.org/r/1303900353-10242-1-git-send-email-dzickus@redhat.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>
CC: Cyrill Gorcunov <gorcunov@gmail.com>
On Nehalem CPUs the retired branch-misses event can be completely bogus,
when there are no branch-misses occuring. When there are a lot of branch
misses then the count is pretty accurate. Still, this leaves us with an
event that over-counts a lot.
Detect this erratum and work it around by using BR_MISP_EXEC.ANY events.
These will also count speculated branches but still it's a lot more
precise in practice than the architectural event.
Acked-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Link: http://lkml.kernel.org/n/tip-yyfg0bxo9jsqxd6a0ovfny27@git.kernel.org
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Currently the x86 backend incorrectly assumes that any BRANCH_INSN
with sample_period==1 is a BTS request. This is not true when we do
frequency driven profiling such as 'perf record -e branches'.
Solves this error:
$ perf record -e branches ./array
Error: sys_perf_event_open() syscall returned with 95 (Operation not supported).
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Reported-by: Ingo Molnar <mingo@elte.hu>
Cc: "Metzger, Markus T" <markus.t.metzger@intel.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Link: http://lkml.kernel.org/n/tip-rd2y4ct71hjawzz6fpvsy9hg@git.kernel.org
Signed-off-by: Ingo Molnar <mingo@elte.hu>
When we use BIOS function e801 to probe memory, we should use ax/bx
(or cx/dx) as a pair, not mix and match. This was a typo during the
translation from assembly code, and breaks at least one set of
machines in the field (which return cx = dx = 0).
Reported-and-tested-by: Chris Samuel <chris@csamuel.org>
Fix-proposed-by: Thomas Meyer <thomas@m3y3r.de>
Link: http://lkml.kernel.org/r/1303566747.12067.10.camel@localhost.localdomain
While the tracer accesses ptrace breakpoints, the child task may
concurrently exit due to a SIGKILL and thus release its breakpoints
at the same time. We can then dereference some freed pointers.
To fix this, hold a reference on the child breakpoints before
manipulating them.
Reported-by: Oleg Nesterov <oleg@redhat.com>
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Prasad <prasad@linux.vnet.ibm.com>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: v2.6.33.. <stable@kernel.org>
Link: http://lkml.kernel.org/r/1302284067-7860-3-git-send-email-fweisbec@gmail.com
It's not enough to simply disable event on overflow the
cpuc->active_mask should be cleared as well otherwise counter
may stall in "active" even in real being already disabled (which
potentially may lead to the situation that user may not use this
counter further).
Don pointed out that:
" I also noticed this patch fixed some unknown NMIs
on a P4 when I stressed the box".
Tested-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Cyrill Gorcunov <gorcunov@openvz.org>
Acked-by: Don Zickus <dzickus@redhat.com>
Signed-off-by: Don Zickus <dzickus@redhat.com>
Cc: Cyrill Gorcunov <gorcunov@gmail.com>
Link: http://lkml.kernel.org/r/1303398203-2918-3-git-send-email-dzickus@redhat.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Andi Kleen pointed out that the Intel offcore support patches were merged
without user-space tool support to the functionality:
|
| The offcore_msr perf kernel code was merged into 2.6.39-rc*, but the
| user space bits were not. This made it impossible to set the extra mask
| and actually do the OFFCORE profiling
|
Andi submitted a preliminary patch for user-space support, as an
extension to perf's raw event syntax:
|
| Some raw events -- like the Intel OFFCORE events -- support additional
| parameters. These can be appended after a ':'.
|
| For example on a multi socket Intel Nehalem:
|
| perf stat -e r1b7:20ff -a sleep 1
|
| Profile the OFFCORE_RESPONSE.ANY_REQUEST with event mask REMOTE_DRAM_0
| that measures any access to DRAM on another socket.
|
But this kind of usability is absolutely unacceptable - users should not
be expected to type in magic, CPU and model specific incantations to get
access to useful hardware functionality.
The proper solution is to expose useful offcore functionality via
generalized events - that way users do not have to care which specific
CPU model they are using, they can use the conceptual event and not some
model specific quirky hexa number.
We already have such generalization in place for CPU cache events,
and it's all very extensible.
"Offcore" events measure general DRAM access patters along various
parameters. They are particularly useful in NUMA systems.
We want to support them via generalized DRAM events: either as the
fourth level of cache (after the last-level cache), or as a separate
generalization category.
That way user-space support would be very obvious, memory access
profiling could be done via self-explanatory commands like:
perf record -e dram ./myapp
perf record -e dram-remote ./myapp
... to measure DRAM accesses or more expensive cross-node NUMA DRAM
accesses.
These generalized events would work on all CPUs and architectures that
have comparable PMU features.
( Note, these are just examples: actual implementation could have more
sophistication and more parameter - as long as they center around
similarly simple usecases. )
Now we do not want to revert *all* of the current offcore bits, as they
are still somewhat useful for generic last-level-cache events, implemented
in this commit:
e994d7d23a0b: perf: Fix LLC-* events on Intel Nehalem/Westmere
But we definitely do not yet want to expose the unstructured raw events
to user-space, until better generalization and usability is implemented
for these hardware event features.
( Note: after generalization has been implemented raw offcore events can be
supported as well: there can always be an odd event that is marginally
useful but not useful enough to generalize. DRAM profiling is definitely
*not* such a category so generalization must be done first. )
Furthermore, PERF_TYPE_RAW access to these registers was not intended
to go upstream without proper support - it was a side-effect of the above
e994d7d23a commit, not mentioned in the changelog.
As v2.6.39 is nearing release we go for the simplest approach: disable
the PERF_TYPE_RAW offcore hack for now, before it escapes into a released
kernel and becomes an ABI.
Once proper structure is implemented for these hardware events and users
are offered usable solutions we can revisit this issue.
Reported-by: Andi Kleen <ak@linux.intel.com>
Acked-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Link: http://lkml.kernel.org/r/1302658203-4239-1-git-send-email-andi@firstfloor.org
Signed-off-by: Ingo Molnar <mingo@elte.hu>
The cpu<->node mappings under CONFIG_DEBUG_PER_CPU_MAPS=y
when NUMA emulation is enabled is currently broken because it does
not iterate through every emulated node and bind cpus that have
affinity to it.
NUMA emulation should bind each cpu to every local node to
accurately represent the true NUMA topology of the underlying
machine.
debug_cpumask_set_cpu() needs to be fixed at the same time so
that the debugging information that it emits shows the new
cpumask of the node being assigned when the cpu is being added
or removed.
It can now take responsibility of setting or clearing the cpu
itself to remove the need for duplicate code.
Also change its last parameter, "enable", to have the correct bool
type since it can only be true or false.
-v2: Fix the return statements, by Kosaki Motohiro
Acked-and-Tested-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Signed-off-by: David Rientjes <rientjes@google.com>
Cc: Andreas Herrmann <herrmann.der.user@googlemail.com>
Cc: Tejun Heo <tj@kernel.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Link: http://lkml.kernel.org/r/alpine.DEB.2.00.1104201918470.12634@chino.kir.corp.google.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Andreas Herrmann reported that 7d6b46707f ("x86, NUMA: Fix fakenuma
boot failure") causes certain physical NUMA topologies (for example
AMD Magny-Cours) to move sibling cpus to a single node when in reality
they are in separate domains.
This may result in some nodes being completely void of cpus, which
doesn't accurately represent the correct topology. The system will
boot, but will have suboptimal NUMA performance.
This commit was intended as a fix for NUMA emulation, but should
not cause a regression for real NUMA machines as a side effect.
( There will be a separate fix for the numa-debug code, which
will not affect physical topologies. )
Reported-by: Andreas Herrmann <herrmann.der.user@googlemail.com>
Signed-off-by: David Rientjes <rientjes@google.com>
Acked-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Cc: Tejun Heo <tj@kernel.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Link: http://lkml.kernel.org/r/alpine.DEB.2.00.1104201918110.12634@chino.kir.corp.google.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>
* 'stable/bug-fixes-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen:
xen: mask_rw_pte: do not apply the early_ioremap checks on x86_32
xen: do not create the extra e820 region at an addr lower than 4G
The two "is_early_ioremap_ptep" checks in mask_rw_pte are only used on
x86_64, in fact early_ioremap is not used at all to setup the initial
pagetable on x86_32.
Moreover on x86_32 the two checks are wrong because the range
pgt_buf_start..pgt_buf_end initially should be mapped RW because
the pages in the range are not pagetable pages yet and haven't been
cleared yet. Afterwards considering the pgt_buf_start..pgt_buf_end is
part of the initial mapping, xen_alloc_pte is capable of turning
the ptes RO when they become pagetable pages.
Fix the issue and improve the readability of the code providing two
different implementation of mask_rw_pte for x86_32 and x86_64.
Signed-off-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Do not add the extra e820 region at a physical address lower than 4G
because it breaks e820_end_of_low_ram_pfn().
It is OK for us to move the xen_extra_mem_start up and down because this
is the index of the memory that can be ballooned in/out - it is memory
not available to the kernel during bootup.
Signed-off-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Device suspend/resume infrastructure is used not only by the suspend
and hibernate code in kernel/power, but also by APM, Xen and the
kexec jump feature. However, commit 40dc166cb5
(PM / Core: Introduce struct syscore_ops for core subsystems PM)
failed to add syscore_suspend() and syscore_resume() calls to that
code, which generally leads to breakage when the features in question
are used.
To fix this problem, add the missing syscore_suspend() and
syscore_resume() calls to arch/x86/kernel/apm_32.c, kernel/kexec.c
and drivers/xen/manage.c.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Acked-by: Ian Campbell <ian.campbell@citrix.com>
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86, gart: Make sure GART does not map physmem above 1TB
x86, gart: Set DISTLBWALKPRB bit always
x86, gart: Convert spaces to tabs in enable_gart_translation
* 'perf-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
perf, x86: Fix AMD family 15h FPU event constraints
perf, x86: Fix pre-defined cache-misses event for AMD family 15h cpus
perf evsel: Fix use of inherit
perf hists browser: Fix seg fault when annotate null symbol
Depending on the unit mask settings some FPU events may be scheduled
only on cpu counter #3. This patch fixes this.
Signed-off-by: Robert Richter <robert.richter@amd.com>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Stephane Eranian <eranian@googlemail.com>
Link: http://lkml.kernel.org/r/1302913676-14352-3-git-send-email-robert.richter@amd.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>
With AMD cpu family 15h a unit mask was introduced for the Data Cache
Miss event (0x041/L1-dcache-load-misses). We need to enable bit 0
(first data cache miss or streaming store to a 64 B cache line) of
this mask to proper count data cache misses.
Now we set this bit for all families and models. In case a PMU does
not implement a unit mask for event 0x041 the bit is ignored.
Signed-off-by: Andre Przywara <andre.przywara@amd.com>
Signed-off-by: Robert Richter <robert.richter@amd.com>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/r/1302913676-14352-2-git-send-email-robert.richter@amd.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>
The GART can only map physical memory below 1TB. Make sure
the gart driver in the kernel does not try to map memory
above 1TB.
Cc: <stable@kernel.org>
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Link: http://lkml.kernel.org/r/1303134346-5805-5-git-send-email-joerg.roedel@amd.com
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
The DISTLBWALKPRB bit must be set for the GART because the
gatt table is mapped UC. But the current code does not set
the bit at boot when the BIOS setup the aperture correctly.
Fix that by setting this bit when enabling the GART instead
of the other places.
Cc: <stable@kernel.org>
Cc: Borislav Petkov <borislav.petkov@amd.com>
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Link: http://lkml.kernel.org/r/1303134346-5805-4-git-send-email-joerg.roedel@amd.com
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
* 'core-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
futex: Set FLAGS_HAS_TIMEOUT during futex_wait restart setup
* 'perf-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
perf_event: Fix cgrp event scheduling bug in perf_enable_on_exec()
perf: Fix a build error with some GCC versions
* 'sched-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
sched: Fix erroneous all_pinned logic
sched: Fix sched-domain avg_load calculation
* 'timer-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
RTC: rtc-mrst: follow on to the change of rtc_device_register()
RTC: add missing "return 0" in new alarm func for rtc-bfin.c
RTC: Fix s3c compile error due to missing s3c_rtc_setpie
RTC: Fix early irqs caused by calling rtc_set_alarm too early
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86, amd: Disable GartTlbWlkErr when BIOS forgets it
x86, NUMA: Fix fakenuma boot failure
x86/mrst: Fix boot crash caused by incorrect pin to irq mapping
x86/ce4100: Add reg property to bridges
This patch disables GartTlbWlk errors on AMD Fam10h CPUs if
the BIOS forgets to do is (or is just too old). Letting
these errors enabled can cause a sync-flood on the CPU
causing a reboot.
The AMD BKDG recommends disabling GART TLB Wlk Error completely.
This patch is the fix for
https://bugzilla.kernel.org/show_bug.cgi?id=33012
on my machine.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Link: http://lkml.kernel.org/r/20110415131152.GJ18463@8bytes.org
Tested-by: Alexandre Demers <alexandre.f.demers@gmail.com>
Cc: <stable@kernel.org>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Linus Torvalds
Borislav Petkov
Youquan Song
Julia Lawall
Cliff Wickman
Sedat Dilek
Stefano Stabellini
Konrad Rzeszutek Wilk
Jiri Olsa
Jack Steiner
Peter Zijlstra
Ingo Molnar
H. Peter Anvin
Yinghai Lu
Boris Ostrovsky
Sebastian Andrzej Siewior
Don Zickus
Peter Zijlstra
H. Peter Anvin
Frederic Weisbecker
Cyrill Gorcunov
Andi Kleen
David Rientjes
Rafael J. Wysocki
Robert Richter
Andre Przywara
Joerg Roedel