The dma_mapping_error() returns true or false, but we want
to return -ENOMEM if there was an error.
Fixes: 174fd2597b ("amd-xgbe: Implement split header receive support")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ido Schimmel says:
====================
mlxsw: Introduce algorithmic TCAM support
The Spectrum-2 ASIC uses an algorithmic TCAM (A-TCAM) where multiple
exact matches lookups are performed instead of a single lookup as with
standard circuit TCAM (C-TCAM) memory. This allows for higher scale and
reduced power consumption.
The lookups are performed by masking a packet using different masks
(e.g., {dst_ip/24, ethtype}) defined for the region and looking for an
exact match. Eventually, the rule with the highest priority will be
picked.
Since the number of masks per-region is limited, the ASIC includes a
C-TCAM that can be used as a spill area for rules that do not fit into
the A-TCAM.
The driver currently uses a C-TCAM only mode which is similar to
Spectrum-1. However, this mode severely limits both the number of
supported ACL rules and the performance of the ACL lookup.
This patch set introduces initial support for the A-TCAM mode where the
C-TCAM is only used for rule spillage.
The first five patches add the registers and ASIC resources needed in
order to make use of the A-TCAM.
Next three patches are the "meat" and add the eRP core which is used to
manage the masks used by each ACL region. The individual commit messages
are lengthy and aim to thoroughly explain the subject.
The next seven patches perform small adjustments in the code and the
related data structures and are meant to prepare the code base to the
introduction of the A-TCAM in the last two patches.
Various A-TCAM optimization will be the focus of follow-up patch sets:
* Pruning - Used to reduce the number of lookups. Each rule will include
a prune vector that indicates which masks should not be considered for
further lookups as they cannot result in a higher priority match
* Bloom filter - Used to reduce the number of lookups. Before performing
a lookup with a given mask the ASIC will consult a bloom filter
(managed by the driver) that indicates whether a match might exist using
the considered mask
* Masks aggregation - Used to increase scale and reduce lookups. Masks
that only differ by up to eight consecutive bits (delta bits) can be
aggregated into a single mask. The delta bits then become a part of the
rule's key. For example, dst_ip/16 and dst_ip/17 can be represented as
dst_ip/16 with a delta bit of one. Rules using the aggregated mask then
specify whether the 17-th bit should be masked or not and its value
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that all the pieces are in place we can start using the A-TCAM
instead of only using the C-TCAM. This allows for much higher scale and
better performance (to be improved further by follow-up patch sets).
Perform the integration with the A-TCAM and the eRP core by reverting
the changes introduced by "mlxsw: spectrum_acl: Enable C-TCAM only mode
in eRP core" and add calls from the C-TCAM code into the eRP core.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement rule insertion and deletion into the A-TCAM before we flip the
driver to start using the A-TCAM.
Rule insertion into the A-TCAM is very similar to C-TCAM, but there are
subtle differences between regions of different sizes (i.e., different
number of key blocks).
Specifically, as explained in "mlxsw: spectrum_acl: Allow encoding a
partial key", in 12 key blocks regions a rule is split into two and the
two halves of the rule are linked using a "large entry key ID".
Such differences are abstracted away by using different region
operations per region type.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When A-TCAM will be used together with C-TCAM, the C-TCAM code will need
to call into the eRP core in order to get an eRP for an inserted entry.
The eRP core takes an A-TCAM region as one of its arguments, so pass the
C-TCAM region to the insertion function which will later allow us to
derive the A-TCAM region, given it contains the C-TCAM one.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Before we start using the A-TCAM we need to make sure the region is
properly initialized.
This includes the setting of its type (which affects the size of its eRP
table, for example) and its registration with the eRP core.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Each TCAM region currently uses its own resources and there is no
sharing between the different regions.
This is going to change with A-TCAM as each region will need to allocate
an eRP table from the global eRP tables array.
Make the global TCAM resources available to each region by passing the
TCAM private data to the region initialization routine.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In Spectrum-2 the C-TCAM is only used for rules that can't fit in the
A-TCAM due to a limited number of masks per A-TCAM region.
In addition, rules inserted into the C-TCAM may affect rules residing in
the A-TCAM, by clearing their C-TCAM prune bit.
The two regions are thus closely related and can be thought of as if the
C-TCAM region is encapsulated in the A-TCAM one.
Change the data structures to reflect that before introducing A-TCAM
support and make C-TCAM region initialization part of the A-TCAM region
initialization sequence.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Initialize the A-TCAM as part of the driver's initialization routine.
Specifically, initialize the eRP tables so that A-TCAM regions will be
able to perform allocations of eRP tables upon rule insertion in
subsequent patches.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When working with 12 key blocks in the A-TCAM, rules are split into two
records, which constitute two lookups. The two records are linked using
a "large entry key ID". The ID is assigned to key blocks 6 to 11 and
resolved during the first lookup. The second lookup is performed using
the ID and the remaining key blocks.
Allow encoding a partial key so that it can be later used to check if an
ID can be reused.
This is done by adding two arguments to the existing encode function
that specify the range of the block indexes we would like to encode. The
key and mask arguments become optional, as we will not need to encode
both of them all the time.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In a similar fashion to Spectrum-1's region struct, Spectrum-2's struct
needs to store a pointer to the common region struct.
The pointer will be used in follow-up patches that implement rules
insertion and deletion.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The number of eRPs that can be used by a single A-TCAM region is limited
to 16. When more eRPs are needed, an ordinary circuit TCAM (C-TCAM) can
be used to hold the extra eRPs.
Unlike the A-TCAM, only a single (last) lookup is performed in the
C-TCAM and not a lookup per-eRP. However, modeling the C-TCAM as extra
eRPs will allow us to easily introduce support for pruning in a
follow-up patch set and is also logically correct.
The following diagram depicts the relation between both TCAMs:
C-TCAM
+-------------------+ +--------------------+ +-----------+
| | | | | |
| eRP #1 (A-TCAM) +----> ... +----+ eRP #16 (A-TCAM) +----+ eRP #17 |
| | | | | ... |
+-------------------+ +--------------------+ | eRP #N |
| |
+-----------+
Lookup order is from left to right.
Extend the eRP core APIs with a C-TCAM parameter which indicates whether
the requested eRP is to be used with the C-TCAM or not.
Since the C-TCAM is only meant to absorb rules that can't fit in the
A-TCAM due to exceeded number of eRPs or key collision, an error is
returned when a C-TCAM eRP needs to be created when the eRP state
machine is in its initial state (i.e., 'no masks'). This should only
happen in the face of very unlikely errors when trying to push rules
into the A-TCAM.
In order not to perform unnecessary lookups, the eRP core will only
enable a C-TCAM lookup for a given region if it knows there are C-TCAM
eRPs present.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, no calls are performed into the eRP core, but in order to
make review easier we would like to gradually add these calls.
Have the eRP core initialize a region's master mask to all ones and
allow it to use an empty eRP table. This directs the lookup to the
C-TCAM and allows the C-TCAM only mode to continue working.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When rules are inserted into the A-TCAM they are associated with a mask,
which is part of the lookup key: { masked key, mask ID, region ID }.
These masks are called rule patterns (RP) and the aggregation of several
masks into one (to be introduced in follow-up patch sets) is called an
extended RP (eRP).
When a packet undergoes a lookup in an ACL region it is masked by the
current set of eRPs used by the region, looking for an exact match.
Eventually, the rule with the highest priority is picked.
These eRPs are stored in several global banks to allow for lookup to
occur using several eRPs simultaneously.
At first, an ACL region will only require a single mask - upon the
insertion of the first rule. In this case, the region can use the
"master RP" which is composed by OR-ing all the masks used by the
region. This mask is a property of the region and thus there is no need
to use the above mentioned banks.
At some point, a second mask will be needed. In this case, the region
will need to allocate an eRP table from the above mentioned banks and
insert its masks there.
>From now on, upon lookup, the eRP table used by the region will be
fetched from the eRP banks - using {eRP bank, Index within the bank} -
and the eRPs present in the table will be used to mask the packet. Note
that masks with consecutive indexes are inserted into consecutive banks.
When rules are deleted and a region only needs a single mask once again
it can free its eRP table and use the master RP.
The above logic is implemented in the eRP core and represented using the
following state machine:
+------------+ create mask - as master RP +---------------+
| +--------------------------------> |
| no masks | | single mask |
| <--------------------------------+ |
+------------+ delete mask +-----+--^------+
| |
| |
create mask - | | delete mask -
create mask transition to use eRP | | transition to
+--------+ table | | use master RP
| | | |
| | | |
+----v--------+----+ create mask +----v--+-----+
| <-------------------------------+ |
| multiple masks | | two masks |
| +-------------------------------> |
+------------------+ delete mask - if two +-------------+
remaining
The code that actually configures rules in the A-TCAM will interface
with the eRP core by getting or putting an eRP based on the required
mask used by the rule.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the following resources to be used by A-TCAM code:
* Maximum number of eRP banks
* Maximum size of eRP bank
* Number of eRP entries required for a 2/4/8/12 key blocks mask
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a resource to make sure we do not exceed the maximum number of
supported large key IDs in a region.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The register is used to add and delete eRPs from the eRP table.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The register is used to configure rules in the A-TCAM.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Before introducing A-TCAM support we need to make sure all the necessary
fields are configurable and not hard coded to values that worked for the
C-TCAM only use case.
This includes - for example - the ability to configure the eRP table
used by the TCAM region.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes the following sparse warning:
drivers/net/ethernet/microchip/lan743x_main.c:2944:25: warning:
symbol 'lan743x_pm_ops' was not declared. Should it be static?
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Acked-by: Bryan Whitehead <Bryan.Whitehead@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes the following sparse warnings:
net/ipv4/tcp_timer.c:25:5: warning:
symbol 'tcp_retransmit_stamp' was not declared. Should it be static?
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This fixes the following sparse warning:
net/sched/cls_flower.c:1356:36: warning: incorrect type in argument 3 (different base types)
net/sched/cls_flower.c:1356:36: expected unsigned short [unsigned] [usertype] value
net/sched/cls_flower.c:1356:36: got restricted __be16 [usertype] vlan_tpid
Signed-off-by: Jianbo Liu <jianbol@mellanox.com>
Reported-by: Or Gerlitz <ogerlitz@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow obtaining MTTs starting at any index,
thus give a better cache utilization.
For this, allow setting log_mtts_per_seg to 0, and use
this in default.
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Eli Cohen <eli@mellanox.co.il>
Signed-off-by: Anaty Rahamim Bar Kat <anaty@mellanox.com>
Reviewed-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
Or Gerlitz says:
====================
net/mlx5: Offload setting/matching on tunnel tos/ttl
This series enables mlx5 offloading of tc eswitch rules that set
tos/ttl (encap) or match on them (decap) for tunnels.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Enable offloading of TC matching on tos/ttl for ipv4/6 tunnels.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the values provided by user-space for the encapsulation headers.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currnetly, the ttl for the encapsulation headers is taken from the
route lookup result. As a pre-step to allow for an offload case when
the user specifies the ttl, take it from the route lookup only if
not zero. While here, also move to use u8 instead int for the ttl.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The vxge driver doesn't need anything provided by pci_hotplug.h, so remove
the unnecessary include of it.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Jon Mason <jdmason@kudzu.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a helper for checking whether polling is used to detect PHY status
changes.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use generic kernel CRC32 implementation because it:
1. Should be faster (uses lookup tables),
2. Removes duplicated CRC generation code,
3. Uses well-proven algorithm instead of coding it one more time.
Suggested-by: Eric Biggers <ebiggers3@gmail.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use generic kernel CRC32 implementation because it:
1. Should be faster (uses lookup tables),
2. Removes duplicated CRC generation code,
3. Uses well-proven algorithm instead of coding it one more time.
Suggested-by: Eric Biggers <ebiggers3@gmail.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
genphy_config_aneg() should be called only by PHYs that implement
the Clause 22 register set. Prevent Clause 45 PHYs that don't implement
the register set from calling the genphy function.
Signed-off-by: Camelia Groza <camelia.groza@nxp.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Toshiaki Makita says:
====================
virtio_net: Add ethtool stat items
Add some ethtool stat items useful for performance analysis.
====================
Signed-off-by: Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
So we can infer the number of VM-Exits.
Signed-off-by: Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add counters below:
* Tx
- xdp_tx: frames sent by ndo_xdp_xmit or XDP_TX.
- xdp_tx_drops: dropped frames out of xdp_tx ones.
* Rx
- xdp_packets: frames went through xdp program.
- xdp_tx: XDP_TX frames.
- xdp_redirects: XDP_REDIRECT frames.
- xdp_drops: any dropped frames out of xdp_packets ones.
Signed-off-by: Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make sure to use the same logic in all places to determine xdp sq. This
is useful for xdp counters which the following commit will introduce as
well.
Signed-off-by: Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since when XDP was introduced, drop counter has been able to be updated
much more frequently than before, as XDP_DROP increments the counter.
Thus for performance analysis per-queue drop counter would be useful.
Also this avoids cache contention and race on updating the counter. It
is currently racy because napi handlers read-modify-write it without any
locks.
There are more counters in dev->stats that are racy, but I left them
per-device, because they are rarely updated and does not worth being
per-queue counters IMHO. To fix them we need atomic ops or some kind of
locks.
Signed-off-by: Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
The purpose is to keep receive_buf arguments simple when more per-queue
counter items are added later.
Also XDP_TX related sq counters will be updated in the following changes
so create a container struct virtnet_rx_stats which will includes both
rq and sq statistics. For now it only covers rq stats.
Signed-off-by: Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
When received packets are dropped in virtio_net driver, received packets
counter is incremented but bytes counter is not.
As a result, for instance if we drop all packets by XDP, only received
is counted and bytes stays 0, which looks inconsistent.
IMHO received packets/bytes should be counted if packets are produced by
the hypervisor, like what common NICs on physical machines are doing.
So fix the bytes counter.
Signed-off-by: Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
- Fix an off-by-one in reporting PCI resource sizes to userland which
regressed in v3.12.
- Fix writes to DDR controller registers used to flush write buffers,
which regressed with some refactoring in v4.2.
-----BEGIN PGP SIGNATURE-----
iIsEABYIADMWIQRgLjeFAZEXQzy86/s+p5+stXUA3QUCW1eaYhUccGF1bC5idXJ0
b25AbWlwcy5jb20ACgkQPqefrLV1AN3KEQD/R35j0nU28kbNtIG4bDABZmjN42qy
KRwLdryf3eRLVYkA/3QUGskbEKzJjvasM2Ia+hyx0CMmgigjtrr6iK5B+8sJ
=0pT0
-----END PGP SIGNATURE-----
Merge tag 'mips_fixes_4.18_4' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux
Pull MIPS fixes from Paul Burton:
"A couple more MIPS fixes for 4.18:
- Fix an off-by-one in reporting PCI resource sizes to userland which
regressed in v3.12.
- Fix writes to DDR controller registers used to flush write buffers,
which regressed with some refactoring in v4.2"
* tag 'mips_fixes_4.18_4' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux:
MIPS: ath79: fix register address in ath79_ddr_wb_flush()
MIPS: Fix off-by-one in pci_resource_to_user()
Pull networking fixes from David Miller:
1) Handle stations tied to AP_VLANs properly during mac80211 hw
reconfig. From Manikanta Pubbisetty.
2) Fix jump stack depth validation in nf_tables, from Taehee Yoo.
3) Fix quota handling in aRFS flow expiration of mlx5 driver, from Eran
Ben Elisha.
4) Exit path handling fix in powerpc64 BPF JIT, from Daniel Borkmann.
5) Use ptr_ring_consume_bh() in page pool code, from Tariq Toukan.
6) Fix cached netdev name leak in nf_tables, from Florian Westphal.
7) Fix memory leaks on chain rename, also from Florian Westphal.
8) Several fixes to DCTCP congestion control ACK handling, from Yuchunk
Cheng.
9) Missing rcu_read_unlock() in CAIF protocol code, from Yue Haibing.
10) Fix link local address handling with VRF, from David Ahern.
11) Don't clobber 'err' on a successful call to __skb_linearize() in
skb_segment(). From Eric Dumazet.
12) Fix vxlan fdb notification races, from Roopa Prabhu.
13) Hash UDP fragments consistently, from Paolo Abeni.
14) If TCP receives lots of out of order tiny packets, we do really
silly stuff. Make the out-of-order queue ending more robust to this
kind of behavior, from Eric Dumazet.
15) Don't leak netlink dump state in nf_tables, from Florian Westphal.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (76 commits)
net: axienet: Fix double deregister of mdio
qmi_wwan: fix interface number for DW5821e production firmware
ip: in cmsg IP(V6)_ORIGDSTADDR call pskb_may_pull
bnx2x: Fix invalid memory access in rss hash config path.
net/mlx4_core: Save the qpn from the input modifier in RST2INIT wrapper
r8169: restore previous behavior to accept BIOS WoL settings
cfg80211: never ignore user regulatory hint
sock: fix sg page frag coalescing in sk_alloc_sg
netfilter: nf_tables: move dumper state allocation into ->start
tcp: add tcp_ooo_try_coalesce() helper
tcp: call tcp_drop() from tcp_data_queue_ofo()
tcp: detect malicious patterns in tcp_collapse_ofo_queue()
tcp: avoid collapses in tcp_prune_queue() if possible
tcp: free batches of packets in tcp_prune_ofo_queue()
ip: hash fragments consistently
ipv6: use fib6_info_hold_safe() when necessary
can: xilinx_can: fix power management handling
can: xilinx_can: fix incorrect clear of non-processed interrupts
can: xilinx_can: fix RX overflow interrupt not being enabled
can: xilinx_can: keep only 1-2 frames in TX FIFO to fix TX accounting
...
Syzbot reported a read beyond the end of the skb head when returning
IPV6_ORIGDSTADDR:
BUG: KMSAN: kernel-infoleak in put_cmsg+0x5ef/0x860 net/core/scm.c:242
CPU: 0 PID: 4501 Comm: syz-executor128 Not tainted 4.17.0+ #9
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS
Google 01/01/2011
Call Trace:
__dump_stack lib/dump_stack.c:77 [inline]
dump_stack+0x185/0x1d0 lib/dump_stack.c:113
kmsan_report+0x188/0x2a0 mm/kmsan/kmsan.c:1125
kmsan_internal_check_memory+0x138/0x1f0 mm/kmsan/kmsan.c:1219
kmsan_copy_to_user+0x7a/0x160 mm/kmsan/kmsan.c:1261
copy_to_user include/linux/uaccess.h:184 [inline]
put_cmsg+0x5ef/0x860 net/core/scm.c:242
ip6_datagram_recv_specific_ctl+0x1cf3/0x1eb0 net/ipv6/datagram.c:719
ip6_datagram_recv_ctl+0x41c/0x450 net/ipv6/datagram.c:733
rawv6_recvmsg+0x10fb/0x1460 net/ipv6/raw.c:521
[..]
This logic and its ipv4 counterpart read the destination port from
the packet at skb_transport_offset(skb) + 4.
With MSG_MORE and a local SOCK_RAW sender, syzbot was able to cook a
packet that stores headers exactly up to skb_transport_offset(skb) in
the head and the remainder in a frag.
Call pskb_may_pull before accessing the pointer to ensure that it lies
in skb head.
Link: http://lkml.kernel.org/r/CAF=yD-LEJwZj5a1-bAAj2Oy_hKmGygV6rsJ_WOrAYnv-fnayiQ@mail.gmail.com
Reported-by: syzbot+9adb4b567003cac781f0@syzkaller.appspotmail.com
Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rx hash/filter table configuration uses rss_conf_obj to configure filters
in the hardware. This object is initialized only when the interface is
brought up.
This patch adds driver changes to configure rss params only when the device
is in opened state. In port disabled case, the config will be cached in the
driver structure which will be applied in the successive load path.
Please consider applying it to 'net' branch.
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Function mlx4_RST2INIT_QP_wrapper saved the qp number passed in the qp
context, rather than the one passed in the input modifier.
However, the qp number in the qp context is not defined as a
required parameter by the FW. Therefore, drivers may choose to not
specify the qp number in the qp context for the reset-to-init transition.
Thus, we must save the qp number passed in the command input modifier --
which is always present. (This saved qp number is used as the input
modifier for command 2RST_QP when a slave's qp's are destroyed).
Fixes: c82e9aa0a8 ("mlx4_core: resource tracking for HCA resources used by guests")
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Skbprio (SKB Priority Queue) is a queueing discipline that prioritizes packets
according to their skb->priority field. Under congestion, already-enqueued lower
priority packets will be dropped to make space available for higher priority
packets. Skbprio was conceived as a solution for denial-of-service defenses that
need to route packets with different priorities as a means to overcome DoS
attacks.
v5
*Do not reference qdisc_dev(sch)->tx_queue_len for setting limit. Instead set
default sch->limit to 64.
v4
*Drop Documentation/networking/sch_skbprio.txt doc file to move it to tc man
page for Skbprio, in iproute2.
v3
*Drop max_limit parameter in struct skbprio_sched_data and instead use
sch->limit.
*Reference qdisc_dev(sch)->tx_queue_len only once, during initialisation for
qdisc (previously being referenced every time qdisc changes).
*Move qdisc's detailed description from in-code to Documentation/networking.
*When qdisc is saturated, enqueue incoming packet first before dequeueing
lowest priority packet in queue - improves usage of call stack registers.
*Introduce and use overlimit stat to keep track of number of dropped packets.
v2
*Use skb->priority field rather than DS field. Rename queueing discipline as
SKB Priority Queue (previously Gatekeeper Priority Queue).
*Queueing discipline is made classful to expose Skbprio's internal priority
queues.
Signed-off-by: Nishanth Devarajan <ndev2021@gmail.com>
Reviewed-by: Sachin Paryani <sachin.paryani@gmail.com>
Reviewed-by: Cody Doucette <doucette@bu.edu>
Reviewed-by: Michel Machado <michel@digirati.com.br>
Acked-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Certain PHY's have issues when operating in GBit slave mode and can
be forced to master mode. Examples are RTL8211C, also the Micrel PHY
driver has a DT setting to force master mode.
If two such chips are link partners the autonegotiation will fail.
Standard defines a self-clearing on read, latched-high bit to
indicate this error. Check this bit to inform the user.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stephen Hemminger says:
====================
net whitespace cleanups
Ran script that I use to check for trailing whitespace and
blank lines at end of files across all files in net/ directory.
These are errors that checkpatch reports and git flags.
These are the resulting fixes broken up mostly by subsystem.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
