with hardware slow in negotiation, the system did freeze
while trying to mount root on nfs at boot time.
the link state has not been initialised so network stack
tried to start transmission right away. this caused instant
retries, as the driver solely stated business upon link down,
rendering the system unusable.
notify carrier off initially to prevent transmission until
phylib will report link up.
Signed-off-by: Oskar Schirmer <oskar@linutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
After the change from mdio polling to irq, it became necessary to
restore the interrupt mask after resetting the chip in fec_stop().
Otherwise, with all irqs disabled, no communication with the PHY will be
possible after e.g. un-/replugging the cable and the device gets
stalled.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The phy_mii_ioctl() function unnecessarily throws away the original ifreq.
We need access to the ifreq in order to support PHYs that can perform
hardware time stamping.
Two maverick drivers filter the ioctl commands passed to phy_mii_ioctl().
This is unnecessary since phylib will check the command in any case.
Signed-off-by: Richard Cochran <richard.cochran@omicron.at>
Signed-off-by: David S. Miller <davem@davemloft.net>
With the move to phylib (commit e6b043d) I was seeing sporadic "MDIO write
timeout" messages. Measure of the actual time spent showed latency times of
more than 1600us.
This patch uses the MII event indication of the FEC hardware to detect
completion of MDIO transactions.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch compile tested only.
Convert legacy PM hooks to dev_pm_ops
Signed-off-by: Denis Kirjanov <dkirjanov@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
* in the actual driver, calling fec_stop and fec_enet_init doesn't
allow to have a working network interface at resume (where a
ifconfig down and up is required to recover the interface)
* by using fec_enet_close and fec_enet_open, this patch solves this
problem and handle the case where the link changed between suspend
and resume
* this patch also disable clock at suspend and reenable it at resume
Signed-off-by: Eric Bénard <eric@eukrea.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
BugLink: http://bugs.launchpad.net/bugs/559065
In fec open/close function, we need to use phy_connect and phy_disconnect
operation before we start/stop phy. Otherwise it will cause system hang.
Only call fec_enet_mii_probe() in open function, because the first open
action will cause NULL pointer error.
Signed-off-by: Bryan Wu <bryan.wu@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The i.MX25 PDK uses RMII to communicate with its PHY. This patch adds
the ability to configure RMII, based on platform data.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Acked-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that core network takes care of trans_start updates, dont do it
in drivers themselves, if possible. Drivers can avoid one cache miss
(on dev->trans_start) in their start_xmit() handler.
Exceptions are NETIF_F_LLTX drivers
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix memory corruption that sometimes result in kernel panic.
Signed-off-by: Mattias Walström <mattias@vmlinux.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Converts the list and the core manipulating with it to be the same as uc_list.
+uses two functions for adding/removing mc address (normal and "global"
variant) instead of a function parameter.
+removes dev_mcast.c completely.
+exposes netdev_hw_addr_list_* macros along with __hw_addr_* functions for
manipulation with lists on a sandbox (used in bonding and 80211 drivers)
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
BugLink: http://bugs.launchpad.net/bugs/457878
v2:
- remove duplicated phy_speed caculation
- fix the phy_speed caculation according to the DataSheet
v1:
- removed old MII phy control code
- add phylib supporting
- add ethtool interface to make user space NetworkManager works
Tested on Freescale i.MX51 Babbage board.
This patch is based on a patch from Frederic Rodo <fred.rodo@gmail.com>
Cc: Frederic Rodo <fred.rodo@gmail.com>
Signed-off-by: Bryan Wu <bryan.wu@canonical.com>
Acked-by: Amit Kucheria <amit.kucheria@canonical.com>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch replaces dev->mc_count in all drivers (hopefully I didn't miss
anything). Used spatch and did small tweaks and conding style changes when
it was suitable.
Jirka
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The i.MX51 babbage board has a FEC ethernet controller with this phy.
In the long term we should resurrect the phylib patches for fec.
Signed-off-by: Amit Kucheria <amit.kucheria@canonical.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>
The fec driver was enabling receive buffer descriptor without allocating
the buffers. Make sure the buffer descriptors are initialized to not
start receiving packets.
Open also calls fec_restart after the rx buffers are allocated. With the code
in fec_restart, it zeroes out the buffer descriptors that have just been
setup.
Signed-off-by: Rob Herring <r.herring@freescale.com>
Signed-off-by: Amit Kucheria <amit.kucheria@canonical.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
fec_enet_init is called by both fec_probe and fec_resume, so it
shouldn't be marked as __init.
Signed-off-by: Steven King <sfking@fdwdc.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/gerg/m68knommu: (53 commits)
m68knommu: Make PAGE_SIZE available to assembly files.
m68knommu: fix ColdFire definition of CLOCK_TICK_RATE
m68knommu: set multi-function pins for ethernet when enabled
m68knommu: remove special interrupt handling code for ne2k support
m68knommu: relax IO_SPACE_LIMIT setting
m68knommu: remove ColdFire direct interrupt register access
m68knommu: create a speciailized ColdFire 5272 interrupt controller
m68knommu: add support for second interrupt controller of ColdFire 5249
m68knommu: clean up old ColdFire timer irq setup
m68knommu: map ColdFire interrupts to correct masking bits
m68knommu: clean up ColdFire 532x CPU timer setup
m68knommu: simplify ColdFire "timers" clock initialization
m68knommu: support code to mask external interrupts on old ColdFire CPU's
m68knommu: merge old ColdFire interrupt controller masking macros
m68knommu: remove duplicate ColdFire mcf_autovector() code
m68knommu: move ColdFire INTC definitions to new include file
m68knommu: mask off all interrupts in ColdFire intc-simr controller
m68knommu: remove timer device interrupt setup for ColdFire 532x
m68knommu: remove interrupt masking from ColdFire pit timer
m68knommu: remove unecessary interrupt level setting in ColdFire 520x setup
...
Now that the ColdFire 5272 has full interrupt controller functionality
we can remove all the interrupt masking and acking code from the FEC
ethernet driver.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
fec_enet_mii, fec_enet_rx and fec_enet_tx are both only called by
fec_enet_interrupt in interrupt context. So they must not use
spin_lock_irq/spin_unlock_irq.
This fixes:
WARNING: at kernel/lockdep.c:2140 trace_hardirqs_on_caller+0x130/0x194()
...
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Cc: Greg Ungerer <gerg@uclinux.org>
Cc: Ben Hutchings <ben@decadent.org.uk>
Cc: Patrick McHardy <kaber@trash.net>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Matt Waddel <Matt.Waddel@freescale.com>
Cc: netdev@vger.kernel.org
Cc: Tim Sander <tim01@vlsi.informatik.tu-darmstadt.de>
Acked-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
mii_discover_phy is only called by fec_enet_mii (via mip->mii_func). So
&fep->mii_lock is already held and mii_discover_phy must not call
mii_queue which locks &fep->mii_lock, too.
This was noticed by lockdep:
=============================================
[ INFO: possible recursive locking detected ]
2.6.31-rc8-00038-g37d0892 #109
---------------------------------------------
swapper/1 is trying to acquire lock:
(&fep->mii_lock){-.....}, at: [<c01569f8>] mii_queue+0x2c/0xcc
but task is already holding lock:
(&fep->mii_lock){-.....}, at: [<c0156328>] fec_enet_interrupt+0x78/0x460
other info that might help us debug this:
2 locks held by swapper/1:
#0: (rtnl_mutex){+.+.+.}, at: [<c0183534>] rtnl_lock+0x18/0x20
#1: (&fep->mii_lock){-.....}, at: [<c0156328>] fec_enet_interrupt+0x78/0x460
stack backtrace:
Backtrace:
[<c00226fc>] (dump_backtrace+0x0/0x108) from [<c01eac14>] (dump_stack+0x18/0x1c)
r6:c781d118 r5:c03e41d8 r4:00000001
[<c01eabfc>] (dump_stack+0x0/0x1c) from [<c005bae4>] (__lock_acquire+0x1a20/0x1a88)
[<c005a0c4>] (__lock_acquire+0x0/0x1a88) from [<c005bbac>] (lock_acquire+0x60/0x74)
[<c005bb4c>] (lock_acquire+0x0/0x74) from [<c01edda8>] (_spin_lock_irqsave+0x54/0x68)
r7:60000093 r6:c01569f8 r5:c785e468 r4:00000000
[<c01edd54>] (_spin_lock_irqsave+0x0/0x68) from [<c01569f8>] (mii_queue+0x2c/0xcc)
r7:c785e468 r6:c0156b24 r5:600a0000 r4:c785e000
[<c01569cc>] (mii_queue+0x0/0xcc) from [<c0156b78>] (mii_discover_phy+0x54/0xa8)
r8:00000002 r7:00000032 r6:c785e000 r5:c785e360 r4:c785e000
[<c0156b24>] (mii_discover_phy+0x0/0xa8) from [<c0156354>] (fec_enet_interrupt+0xa4/0x460)
r5:c785e360 r4:c077a170
[<c01562b0>] (fec_enet_interrupt+0x0/0x460) from [<c0066674>] (handle_IRQ_event+0x48/0x120)
[<c006662c>] (handle_IRQ_event+0x0/0x120) from [<c0068438>] (handle_level_irq+0x94/0x11c)
...
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Cc: Greg Ungerer <gerg@uclinux.org>
Cc: Ben Hutchings <ben@decadent.org.uk>
Cc: Patrick McHardy <kaber@trash.net>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Matt Waddel <Matt.Waddel@freescale.com>
Cc: netdev@vger.kernel.org
Cc: Tim Sander <tim01@vlsi.informatik.tu-darmstadt.de>
Acked-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit f0b3fbeae1 ("FEC Buffer rework")
breaks transmission of packets where the skb data buffer is not memory
aligned according to FEC_ALIGNMENT. It incorrectly passes to
dma_sync_single() the buffer address directly from the skb, instead of
the address calculated for use (which may be the skb address or one of
the bounce buffers).
It seems there is no use converting the cpu address of the buffer to
a physical either, since dma_map_single() expects the cpu address and
will return the dma address to use in the descriptor. So remove the use
of __pa() on the buffer address as well.
This patch is against 2.6.30-rc5. This breakage is a regression over
2.6.30, which does not have this problem.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
alloc_etherdev() used to install a default implementation of this
operation, but it must now be explicitly installed in struct
net_device_ops.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is the result of an automatic spatch transformation to convert
all ndo_start_xmit() return values of 0 to NETDEV_TX_OK.
Some occurences are missed by the automatic conversion, those will be
handled in a seperate patch.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert magic values 1 and -1 to NETDEV_TX_BUSY and NETDEV_TX_LOCKED respectively.
0 (NETDEV_TX_OK) is not changed to keep the noise down, except in very few cases
where its in direct proximity to one of the other values.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
We called fec_stop() in fec_enet_close(), thus we have to call
fec_restart() in fec_enet_open().
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allocate buffers in fec_open and free them again in fec_close. This makes
it possible to use this driver as a module.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
These printks in fec_timeout do not give useful information in
a production kernel.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
fec_enet_init() does the hardware initialisation and then calls
fec_restart() which does the same initialisation again, so we
can safely remove the initialisation from fec_enet_init().
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove the ColdFire CPU specific setup from here. The ColdFire
CPU platform code now sets up all this.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This turns the fec driver into a platform device driver for new
platforms. Old platforms are still supported through a FEC_LEGACY define
till they are also ported.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
flush_dcache_range is not portable across architectures. Use
dma_sync_single instead. Also, the memory must be synchronised in the
receive path aswell.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
