Commit Graph

24 Commits

Author SHA1 Message Date
Paul Walmsley d9a16f9ab9 ARM: OMAP2+: PRCM: split and relocate the PRM/CM globals setup
Split omap2_set_globals_prcm() into PRM, CM, and PRCM_MPU variants, since
these are all separate IP blocks.  This should make it easier to move the
PRM, CM, PRCM_MPU code into drivers/ in future patchsets.

At this point arch/arm/plat-omap/include/plat/prcm.h is empty; a
subsequent patch will remove it, and remove the #include from all the
files that #include it.

Signed-off-by: Paul Walmsley <paul@pwsan.com>
Tested-by: Vaibhav Hiremath <hvaibhav@ti.com>
2012-11-08 15:09:26 -07:00
Paul Walmsley c4ceedcb18 ARM: OMAP2+: CM/clock: convert _omap2_module_wait_ready() to use SoC-independent CM functions
Convert the OMAP clock code's _omap2_module_wait_ready() to use
SoC-independent CM functions that are provided by the CM code, rather
than using a deprecated function from mach-omap2/prcm.c.

This facilitates the future conversion of the CM code to a driver, and
also removes a mach-omap2/prcm.c user.  mach-omap2/prcm.c will be removed
by a subsequent patch.

Some modules have IDLEST registers that aren't in the CM module, such
as the AM3517 IDLEST bits.  So we also need a fallback function for
these non-CM odd cases.  Create a temporary one in mach-omap2/clock.c,
intended to exist until the SCM drivers are ready.

Signed-off-by: Paul Walmsley <paul@pwsan.com>
Tested-by: Vaibhav Hiremath <hvaibhav@ti.com>
2012-11-08 12:33:08 -07:00
Paul Walmsley 21325b25f4 ARM: OMAP2+: CM: prepare for use of cm_ll_data function pointers
There are several CM operations which behave similarly across OMAP2+
SoCs, but which have slight differences in their underlying
implementations.

This patch creates the support code for this function pointer
registration process.  No function pointers are included yet, but a
subsequent patch will create these for the module IDLEST registers.

This patch allows other code to use CM-provided data and operations
without needing to know which SoC is currently in use.  A further
description of the concept is provided in the patch entitled
"ARM: OMAP2+: PRM: prepare for use of prm_ll_data function pointers".

Signed-off-by: Paul Walmsley <paul@pwsan.com>
2012-10-21 01:01:12 -06:00
Paul Walmsley b8f15b7e1d ARM: OMAP2+: CM: increase the module disable timeout
Increase the timeout for disabling an IP block to five milliseconds.
This is to handle the usb_host_fs idle latency, which takes almost
four milliseconds after a host controller reset.

This is the second of two patches needed to resolve the following
boot warning:

omap_hwmod: usb_host_fs: _wait_target_disable failed

Thanks to Sergei Shtylyov <sshtylyov@mvista.com> for finding
an unrelated hunk in a previous version of this patch.

Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Sergei Shtylyov <sshtylyov@mvista.com>
Cc: Tero Kristo <t-kristo@ti.com>
2012-06-21 18:08:47 -06:00
Paul Walmsley 59fb659b06 OMAP2/3: PRCM: split OMAP2/3-specific PRCM code into OMAP2/3-specific files
In preparation for adding OMAP4-specific PRCM accessor/mutator
functions, split the existing OMAP2/3 PRCM code into OMAP2/3-specific
files.  Most of what was in mach-omap2/{cm,prm}.{c,h} has now been
moved into mach-omap2/{cm,prm}2xxx_3xxx.{c,h}, since it was
OMAP2xxx/3xxx-specific.

This process also requires the #includes in each of these files to be
changed to reference the new file name.  As part of doing so, add some
comments into plat-omap/sram.c and plat-omap/mcbsp.c, which use
"sideways includes", to indicate that these users of the PRM/CM includes
should not be doing so.

Thanks to Felipe Contreras <felipe.contreras@gmail.com> for comments on this
patch.

Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Jarkko Nikula <jhnikula@gmail.com>
Cc: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Cc: Liam Girdwood <lrg@slimlogic.co.uk>
Cc: Omar Ramirez Luna <omar.ramirez@ti.com>
Acked-by: Omar Ramirez Luna <omar.ramirez@ti.com>
Cc: Felipe Contreras <felipe.contreras@gmail.com>
Acked-by: Felipe Contreras <felipe.contreras@gmail.com>
Cc: Greg Kroah-Hartman <greg@kroah.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Reviewed-by: Kevin Hilman <khilman@deeprootsystems.com>
Tested-by: Kevin Hilman <khilman@deeprootsystems.com>
Tested-by: Rajendra Nayak <rnayak@ti.com>
Tested-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
2010-12-21 20:01:55 -07:00
Paul Walmsley d198b514bd OMAP4: PRCM: reorganize existing OMAP4 PRCM header files
Split the existing cm44xx.h file into cm1_44xx.h and cm2_44xx.h files
so they match their underlying OMAP hardware modules.  Add clockdomain
offset information.

Add header files for the MPU local PRCM, prcm_mpu44xx.h, and for the
SCRM, scrm44xx.h.  SCRM register offsets still need to be added; TI
should do this.

Move the "_MOD" macros out of the prcm-common.h header file, into the
header file of the hardware module that they belong to.  For example,
OMAP4430_PRM_*_MOD macros have been moved into the prm44xx.h header.

Adjust #includes of all files that used the old PRCM header file names
to point to the new filenames.

The autogeneration scripts have been updated accordingly.

Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Benoît Cousson <b-cousson@ti.com>
Cc: Rajendra Nayak <rnayak@ti.com>
Reviewed-by: Kevin Hilman <khilman@deeprootsystems.com>
Tested-by: Kevin Hilman <khilman@deeprootsystems.com>
Tested-by: Rajendra Nayak <rnayak@ti.com>
Tested-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
2010-12-21 20:01:54 -07:00
Benoit Cousson 9a23dfe128 OMAP4: hwmod & CM: Implement the omap4_cm_wait_module_ready function
The return of the omap4_cm_wait_module_ready function is checked
in order to avoid accessing the sysconfig register if the module is
not in the correct state.
In that case the _setup will exit without trying to reset
using sysconfig.
For the moment a warning is printed. A proper management of fclk
and module reset will have to be done in order to init correctly
the problematic IPs listed below.

  <4>omap_hwmod: ivahd: cannot be enabled (3)
  <4>omap_hwmod: iss: cannot be enabled (3)
  <4>omap_hwmod: tesla: cannot be enabled (3)
  <4>omap_hwmod: sdma: cannot be enabled (3)
  <4>omap_hwmod: sl2: cannot be enabled (3)
  <4>omap_hwmod: sad2d: cannot be enabled (3)
  <4>omap_hwmod: ducati: cannot be enabled (3)

Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
2010-05-20 12:31:08 -06:00
Benoit Cousson d9e6625c70 OMAP: CM: Move MAX_MODULE_READY_TIME to cm.h
The maximum timeout to wait for the PRCM to request that a module
exit idle or reach functionnal state is common to OMAP2/3/4 SoCs,
so, move it to the chip family-common cm.h include file.

Reduce the timeout from 20 ms to 2 ms.

Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
2010-05-20 12:31:08 -06:00
Paul Walmsley 2fd0f75cb3 OMAP2+ PRCM: convert remaining PRCM macros to the _SHIFT/_MASK suffixes
Fix all of the remaining PRCM register shift/bitmask macros that did not
use the _SHIFT/_MASK suffixes to use them.  This makes the use of these
macros consistent.  It is intended to reduce error, as code can be inspected
visually by reviewers to ensure that bitshifts and bitmasks are used in
the appropriate places.

Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
2010-05-20 12:31:05 -06:00
Ranjith Lohithakshan 419cc97d36 OMAP2/3 clock: Extend find_idlest() to pass back idle state value
Current implementation defines clock idle state indicators based on the
cpu information (cpu_is_omap24xx() or cpu_is_omap34xx()) in a system wide
manner. This patch extends the find_idlest() function in clkops to pass
back the idle state indicator for that clock, thus allowing idle state
indicators to be defined on a per clock basis if required.

This is specifically needed on AM35xx devices as the new IPSS clocks
indicates the idle status (0 is idle, 1 is ready) in a way just
opposite to how its handled in OMAP3 (0 is ready, 1 is idle).

Signed-off-by: Ranjith Lohithakshan <ranjithl@ti.com>
[paul@pwsan.com: updated to apply after commit 98c45457 et seq.]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
2010-02-24 12:05:54 -07:00
Abhijit Pagare 84c0c39aec ARM: OMAP4: PM: Make OMAP3 Clock-domain framework compatible for OMAP4.
Here the ".clkstctrl_reg" field is added to the clockdomain stucture
as the module offsets for OMAP4 do not map one to one for powerdomains
and clockdomains as it used to for OMAP3. Hence we need to use absolute
addresses to access the control registers. Some of the clock domains have
modules falling in the address space of PRM partition. Hence  necessitating
the use of absolute adresses.

Signed-off-by: Abhijit Pagare <abhijitpagare@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Benoit Cousson <b-cousson@ti.com>
Cc: Rajendra Nayak <rnayak@ti.com>
2010-01-26 20:12:53 -07:00
Rajendra Nayak d79b126724 ARM: OMAP4: PM: Add dummy hooks for OMAP4 dpll api's
This patch adds dummy hooks for OMAP4 dpll api's. Removes
dummy hooks for clkdev api's and enables CLKDEV
for OMAP4.
Also comments clockdomain calls from within the clock
framework as its not supported yet for OMAP4.

Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Benoit Cousson <b-cousson@ti.com>
2009-12-11 17:00:46 -07:00
Rajendra Nayak 9b47267f3e ARM: OMAP4: PM: Adds CM1/2 register defs for OMAP4
This patch adds OMAP4 specific CM1 and CM2 module
register defs. Autogenerated using a python scripts
(gen_cm1_4430_h.py,gen_cm2_4430_h.py) developed
by Paul Walmsley and Benoit Cousson.

Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Benoit Cousson <b-cousson@ti.com>
2009-12-11 17:00:45 -07:00
Santosh Shilimkar 233fd64e7f omap: Split OMAP2_IO_ADDRESS to L3 and L4
This patch splits OMAP2_IO_ADDRESS to OMAP2_L3_IO_ADDRESS and
OMAP2_L4_IO_ADDRESS to reclaim more IO space.

The omap_read*() and omap_write*() functions will work only over
L4 address space. Current omap kernel stack uses these functions
only to access registers over L4 io address space

Note that these macros should only be used when ioremap does
not work. Please use ioremap instead in all new code.

Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
2009-10-19 15:25:31 -07:00
Paul Walmsley 71348bcaac OMAP2/3/4 PRCM: add module IDLEST wait code
After a hardware module's clocks are enabled, Linux must wait for it
to indicate readiness via its IDLEST bit before attempting to access
the device, otherwise register accesses to the device may trigger an
abort.  This has traditionally been implemented in the clock
framework, but this is the wrong place for it: the clock framework
doesn't know which module clocks must be enabled for a module to leave
idle; and if a module is not in smart-idle mode, it may never leave
idle at all.  This type of information is best stored in a
per-hardware module data structure (coming in a following patch),
rather than a per-clock data structure.  The new code will use these new
functions to handle waiting for modules to enable.

Once hardware module data is filled in for all of the on-chip devices,
the clock framework code to handle IDLEST waiting can be removed.

Signed-off-by: Paul Walmsley <paul@pwsan.com>
2009-09-03 20:14:02 +03:00
Tony Lindgren 941132606c OMAP: Remove OMAP_IO_ADDRESS, use OMAP1_IO_ADDRESS and OMAP2_IO_ADDRESS instead
Search and replace OMAP_IO_ADDRESS with OMAP1_IO_ADDRESS and OMAP2_IO_ADDRESS,
and convert omap_read/write into a functions instead of a macros.

Also rename OMAP_MPUIO_VBASE to OMAP1_MPUIO_VBASE.

In the long run, most code should use ioremap + __raw_read/write instead.

Signed-off-by: Tony Lindgren <tony@atomide.com>
2009-08-28 10:50:33 -07:00
Kevin Hilman 364dd47466 OMAP3: PM: CM_REGADDR macros using wrong name
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
2009-08-05 09:10:50 -07:00
Tony Lindgren ef6685a6de ARM: OMAP2/3: Remove OMAP_CM_REGADDR
Processor specific macros should be used instead.

Signed-off-by: Tony Lindgren <tony@atomide.com>
2009-05-25 11:26:46 -07:00
Tony Lindgren 8e3bd351d1 ARM: OMAP2/3: Remove OMAP_PRM_REGADDR and OMAP2_PRM_BASE
Remove OMAP_PRM_REGADDR and use processor specific defines instead.

Also fold in a patch from Kevin Hilman to add _OFFSET #defines
for the PRCM registers to be used with the prm_[read|write]_* macros.
These are used extensively in the forthcoming OMAP PM support.

Also remove now unused OMAP2_PRM_BASE.

Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
2009-05-25 11:26:42 -07:00
Russell King e8a91c953f [ARM] omap: Fix IO_ADDRESS() macros
OMAP1_IO_ADDRESS(), OMAP2_IO_ADDRESS() and IO_ADDRESS() returns cookies
for use with __raw_{read|write}* for accessing registers.  Therefore,
these macros should return (void __iomem *) cookies, not integer values.

Doing this improves typechecking, and means we can find those places
where, eg, DMA controllers are incorrectly given virtual addresses to
DMA to, or physical addresses are thrown through a virtual to physical
address translation.

Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2008-09-05 17:02:31 +01:00
Paul Walmsley 542313cc98 ARM: OMAP2: Clock: Add OMAP3 DPLL autoidle functions
This patch adds support for DPLL autoidle control to the OMAP3 clock
framework.  These functions will be used by the noncore DPLL enable
and disable code - this is because, according to the CDP code, the
DPLL autoidle status must be saved and restored across DPLL
lock/bypass/off transitions.

N.B.: the CORE DPLL (DPLL3) has three autoidle mode options, rather
than just two.  This code currently does not support the third option,
low-power bypass autoidle.

Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
2008-07-03 12:24:45 +03:00
Tony Lindgren ff00fcc9ca ARM: OMAP: Turn CM and PRM access into functions
Otherwise compiling in omap2 and omap3 will not work.

Signed-off-by: Tony Lindgren <tony@atomide.com>
2008-07-03 12:24:44 +03:00
Tony Lindgren a58caad113 ARM: OMAP: Introduce omap_globals and prcm access functions for multi-omap
New struct omap_globals contains the omap processor specific
module bases. Use omap_globals to set the various base addresses
to make detecting omap chip type simpler.

Also introduce OMAP1_IO_ADDRESS and OMAP2_IO_ADDRESS for future multi-omap
patches.

Signed-off-by: Tony Lindgren <tony@atomide.com>
2008-07-03 12:24:44 +03:00
Paul Walmsley 69d88a00a2 ARM: OMAP2: Add common register access for 24xx and 34xx
This patch adds common register access for 24xx and 34xx power
and clock management in order to share code between 24xx and 34xx.

Only change USB platform init code to use new register access, other
access will be changed in later patches.

Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
2008-04-14 10:27:25 -07:00