Commit Graph

84 Commits

Author SHA1 Message Date
Julien Grall 503a62862e KVM: arm/arm64: vgic: Rely on the GIC driver to parse the firmware tables
Currently, the firmware tables are parsed 2 times: once in the GIC
drivers, the other time when initializing the vGIC. It means code
duplication and make more tedious to add the support for another
firmware table (like ACPI).

Use the recently introduced helper gic_get_kvm_info() to get
information about the virtual GIC.

With this change, the virtual GIC becomes agnostic to the firmware
table and KVM will be able to initialize the vGIC on ACPI.

Signed-off-by: Julien Grall <julien.grall@arm.com>
Reviewed-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
2016-05-03 12:54:21 +02:00
Marc Zyngier 1b8e83c04e arm64: KVM: vgic-v3: Avoid accessing ICH registers
Just like on GICv2, we're a bit hammer-happy with GICv3, and access
them more often than we should.

Adopt a policy similar to what we do for GICv2, only save/restoring
the minimal set of registers. As we don't access the registers
linearly anymore (we may skip some), the convoluted accessors become
slightly simpler, and we can drop the ugly indexing macro that
tended to confuse the reviewers.

Reviewed-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
2016-03-09 04:24:04 +00:00
Marc Zyngier 59f00ff9af KVM: arm/arm64: vgic-v2: Avoid accessing GICH registers
GICv2 registers are *slow*. As in "terrifyingly slow". Which is bad.
But we're equaly bad, as we make a point in accessing them even if
we don't have any interrupt in flight.

A good solution is to first find out if we have anything useful to
write into the GIC, and if we don't, to simply not do it. This
involves tracking which LRs actually have something valid there.

Reviewed-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
2016-03-09 04:22:20 +00:00
Marc Zyngier 9b4a300443 KVM: arm/arm64: timer: Add active state caching
Programming the active state in the (re)distributor can be an
expensive operation so it makes some sense to try and reduce
the number of accesses as much as possible. So far, we
program the active state on each VM entry, but there is some
opportunity to do less.

An obvious solution is to cache the active state in memory,
and only program it in the HW when conditions change. But
because the HW can also change things under our feet (the active
state can transition from 1 to 0 when the guest does an EOI),
some precautions have to be taken, which amount to only caching
an "inactive" state, and always programing it otherwise.

With this in place, we observe a reduction of around 700 cycles
on a 2GHz GICv2 platform for a NULL hypercall.

Reviewed-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
2016-02-29 18:34:22 +00:00
Shannon Zhao bb0c70bcca arm64: KVM: Add a new vcpu device control group for PMUv3
To configure the virtual PMUv3 overflow interrupt number, we use the
vcpu kvm_device ioctl, encapsulating the KVM_ARM_VCPU_PMU_V3_IRQ
attribute within the KVM_ARM_VCPU_PMU_V3_CTRL group.

After configuring the PMUv3, call the vcpu ioctl with attribute
KVM_ARM_VCPU_PMU_V3_INIT to initialize the PMUv3.

Signed-off-by: Shannon Zhao <shannon.zhao@linaro.org>
Acked-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Andrew Jones <drjones@redhat.com>
Reviewed-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
2016-02-29 18:34:21 +00:00
Shannon Zhao 808e738142 arm64: KVM: Add a new feature bit for PMUv3
To support guest PMUv3, use one bit of the VCPU INIT feature array.
Initialize the PMU when initialzing the vcpu with that bit and PMU
overflow interrupt set.

Signed-off-by: Shannon Zhao <shannon.zhao@linaro.org>
Acked-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Andrew Jones <drjones@redhat.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
2016-02-29 18:34:21 +00:00
Shannon Zhao 5f0a714a2b arm64: KVM: Free perf event of PMU when destroying vcpu
When KVM frees VCPU, it needs to free the perf_event of PMU.

Signed-off-by: Shannon Zhao <shannon.zhao@linaro.org>
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Reviewed-by: Andrew Jones <drjones@redhat.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
2016-02-29 18:34:21 +00:00
Shannon Zhao 2aa36e9840 arm64: KVM: Reset PMU state when resetting vcpu
When resetting vcpu, it needs to reset the PMU state to initial status.

Signed-off-by: Shannon Zhao <shannon.zhao@linaro.org>
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Reviewed-by: Andrew Jones <drjones@redhat.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
2016-02-29 18:34:21 +00:00
Shannon Zhao b02386eb7d arm64: KVM: Add PMU overflow interrupt routing
When calling perf_event_create_kernel_counter to create perf_event,
assign a overflow handler. Then when the perf event overflows, set the
corresponding bit of guest PMOVSSET register. If this counter is enabled
and its interrupt is enabled as well, kick the vcpu to sync the
interrupt.

On VM entry, if there is counter overflowed and interrupt level is
changed, inject the interrupt with corresponding level. On VM exit, sync
the interrupt level as well if it has been changed.

Signed-off-by: Shannon Zhao <shannon.zhao@linaro.org>
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Reviewed-by: Andrew Jones <drjones@redhat.com>
Reviewed-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
2016-02-29 18:34:21 +00:00
Shannon Zhao 76993739cd arm64: KVM: Add helper to handle PMCR register bits
According to ARMv8 spec, when writing 1 to PMCR.E, all counters are
enabled by PMCNTENSET, while writing 0 to PMCR.E, all counters are
disabled. When writing 1 to PMCR.P, reset all event counters, not
including PMCCNTR, to zero. When writing 1 to PMCR.C, reset PMCCNTR to
zero.

Signed-off-by: Shannon Zhao <shannon.zhao@linaro.org>
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
2016-02-29 18:34:21 +00:00
Shannon Zhao 7a0adc7064 arm64: KVM: Add access handler for PMSWINC register
Add access handler which emulates writing and reading PMSWINC
register and add support for creating software increment event.

Signed-off-by: Shannon Zhao <shannon.zhao@linaro.org>
Reviewed-by: Andrew Jones <drjones@redhat.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
2016-02-29 18:34:20 +00:00
Shannon Zhao 76d883c4e6 arm64: KVM: Add access handler for PMOVSSET and PMOVSCLR register
Since the reset value of PMOVSSET and PMOVSCLR is UNKNOWN, use
reset_unknown for its reset handler. Add a handler to emulate writing
PMOVSSET or PMOVSCLR register.

When writing non-zero value to PMOVSSET, the counter and its interrupt
is enabled, kick this vcpu to sync PMU interrupt.

Signed-off-by: Shannon Zhao <shannon.zhao@linaro.org>
Reviewed-by: Andrew Jones <drjones@redhat.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
2016-02-29 18:34:20 +00:00
Shannon Zhao 7f76635871 arm64: KVM: PMU: Add perf event map and introduce perf event creating function
When we use tools like perf on host, perf passes the event type and the
id of this event type category to kernel, then kernel will map them to
hardware event number and write this number to PMU PMEVTYPER<n>_EL0
register. When getting the event number in KVM, directly use raw event
type to create a perf_event for it.

Signed-off-by: Shannon Zhao <shannon.zhao@linaro.org>
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
2016-02-29 18:34:20 +00:00
Shannon Zhao 96b0eebcc6 arm64: KVM: Add access handler for PMCNTENSET and PMCNTENCLR register
Since the reset value of PMCNTENSET and PMCNTENCLR is UNKNOWN, use
reset_unknown for its reset handler. Add a handler to emulate writing
PMCNTENSET or PMCNTENCLR register.

When writing to PMCNTENSET, call perf_event_enable to enable the perf
event. When writing to PMCNTENCLR, call perf_event_disable to disable
the perf event.

Signed-off-by: Shannon Zhao <shannon.zhao@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
2016-02-29 18:34:20 +00:00
Shannon Zhao 051ff581ce arm64: KVM: Add access handler for event counter register
These kind of registers include PMEVCNTRn, PMCCNTR and PMXEVCNTR which
is mapped to PMEVCNTRn.

The access handler translates all aarch32 register offsets to aarch64
ones and uses vcpu_sys_reg() to access their values to avoid taking care
of big endian.

When reading these registers, return the sum of register value and the
value perf event counts.

Signed-off-by: Shannon Zhao <shannon.zhao@linaro.org>
Reviewed-by: Andrew Jones <drjones@redhat.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
2016-02-29 18:34:20 +00:00
Shannon Zhao ab9468340d arm64: KVM: Add access handler for PMCR register
Add reset handler which gets host value of PMCR_EL0 and make writable
bits architecturally UNKNOWN except PMCR.E which is zero. Add an access
handler for PMCR.

Signed-off-by: Shannon Zhao <shannon.zhao@linaro.org>
Reviewed-by: Andrew Jones <drjones@redhat.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
2016-02-29 18:34:19 +00:00
Shannon Zhao 04fe472615 arm64: KVM: Define PMU data structure for each vcpu
Here we plan to support virtual PMU for guest by full software
emulation, so define some basic structs and functions preparing for
futher steps. Define struct kvm_pmc for performance monitor counter and
struct kvm_pmu for performance monitor unit for each vcpu. According to
ARMv8 spec, the PMU contains at most 32(ARMV8_PMU_MAX_COUNTERS)
counters.

Since this only supports ARM64 (or PMUv3), add a separate config symbol
for it.

Signed-off-by: Shannon Zhao <shannon.zhao@linaro.org>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Reviewed-by: Andrew Jones <drjones@redhat.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
2016-02-29 18:34:19 +00:00
Marc Zyngier 3c13b8f435 KVM: arm/arm64: vgic-v3: Make the LR indexing macro public
We store GICv3 LRs in reverse order so that the CPU can save/restore
them in rever order as well (don't ask why, the design is crazy),
and yet generate memory traffic that doesn't completely suck.

We need this macro to be available to the C version of save/restore.

Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
2015-12-14 11:30:38 +00:00
Christoffer Dall 0e3dfda91d KVM: arm/arm64: arch_timer: Preserve physical dist. active state on LR.active
We were incorrectly removing the active state from the physical
distributor on the timer interrupt when the timer output level was
deasserted.  We shouldn't be doing this without considering the virtual
interrupt's active state, because the architecture requires that when an
LR has the HW bit set and the pending or active bits set, then the
physical interrupt must also have the corresponding bits set.

This addresses an issue where we have been observing an inconsistency
between the LR state and the physical distributor state where the LR
state was active and the physical distributor was not active, which
shouldn't happen.

Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
2015-11-24 18:07:40 +01:00
Linus Torvalds 933425fb00 s390: A bunch of fixes and optimizations for interrupt and time
handling.
 
 PPC: Mostly bug fixes.
 
 ARM: No big features, but many small fixes and prerequisites including:
 - a number of fixes for the arch-timer
 - introducing proper level-triggered semantics for the arch-timers
 - a series of patches to synchronously halt a guest (prerequisite for
   IRQ forwarding)
 - some tracepoint improvements
 - a tweak for the EL2 panic handlers
 - some more VGIC cleanups getting rid of redundant state
 
 x86: quite a few changes:
 
 - support for VT-d posted interrupts (i.e. PCI devices can inject
 interrupts directly into vCPUs).  This introduces a new component (in
 virt/lib/) that connects VFIO and KVM together.  The same infrastructure
 will be used for ARM interrupt forwarding as well.
 
 - more Hyper-V features, though the main one Hyper-V synthetic interrupt
 controller will have to wait for 4.5.  These will let KVM expose Hyper-V
 devices.
 
 - nested virtualization now supports VPID (same as PCID but for vCPUs)
 which makes it quite a bit faster
 
 - for future hardware that supports NVDIMM, there is support for clflushopt,
 clwb, pcommit
 
 - support for "split irqchip", i.e. LAPIC in kernel + IOAPIC/PIC/PIT in
 userspace, which reduces the attack surface of the hypervisor
 
 - obligatory smattering of SMM fixes
 
 - on the guest side, stable scheduler clock support was rewritten to not
 require help from the hypervisor.
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v2.0.22 (GNU/Linux)
 
 iQEcBAABAgAGBQJWO2IQAAoJEL/70l94x66D/K0H/3AovAgYmJQToZlimsktMk6a
 f2xhdIqfU5lIQQh5uNBCfL3o9o8H9Py1ym7aEw3fmztPHHJYc91oTatt2UEKhmEw
 VtZHp/dFHt3hwaIdXmjRPEXiYctraKCyrhaUYdWmUYkoKi7lW5OL5h+S7frG2U6u
 p/hFKnHRZfXHr6NSgIqvYkKqtnc+C0FWY696IZMzgCksOO8jB1xrxoSN3tANW3oJ
 PDV+4og0fN/Fr1capJUFEc/fejREHneANvlKrLaa8ht0qJQutoczNADUiSFLcMPG
 iHljXeDsv5eyjMtUuIL8+MPzcrIt/y4rY41ZPiKggxULrXc6H+JJL/e/zThZpXc=
 =iv2z
 -----END PGP SIGNATURE-----

Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm

Pull KVM updates from Paolo Bonzini:
 "First batch of KVM changes for 4.4.

  s390:
     A bunch of fixes and optimizations for interrupt and time handling.

  PPC:
     Mostly bug fixes.

  ARM:
     No big features, but many small fixes and prerequisites including:

      - a number of fixes for the arch-timer

      - introducing proper level-triggered semantics for the arch-timers

      - a series of patches to synchronously halt a guest (prerequisite
        for IRQ forwarding)

      - some tracepoint improvements

      - a tweak for the EL2 panic handlers

      - some more VGIC cleanups getting rid of redundant state

  x86:
     Quite a few changes:

      - support for VT-d posted interrupts (i.e. PCI devices can inject
        interrupts directly into vCPUs).  This introduces a new
        component (in virt/lib/) that connects VFIO and KVM together.
        The same infrastructure will be used for ARM interrupt
        forwarding as well.

      - more Hyper-V features, though the main one Hyper-V synthetic
        interrupt controller will have to wait for 4.5.  These will let
        KVM expose Hyper-V devices.

      - nested virtualization now supports VPID (same as PCID but for
        vCPUs) which makes it quite a bit faster

      - for future hardware that supports NVDIMM, there is support for
        clflushopt, clwb, pcommit

      - support for "split irqchip", i.e.  LAPIC in kernel +
        IOAPIC/PIC/PIT in userspace, which reduces the attack surface of
        the hypervisor

      - obligatory smattering of SMM fixes

      - on the guest side, stable scheduler clock support was rewritten
        to not require help from the hypervisor"

* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (123 commits)
  KVM: VMX: Fix commit which broke PML
  KVM: x86: obey KVM_X86_QUIRK_CD_NW_CLEARED in kvm_set_cr0()
  KVM: x86: allow RSM from 64-bit mode
  KVM: VMX: fix SMEP and SMAP without EPT
  KVM: x86: move kvm_set_irq_inatomic to legacy device assignment
  KVM: device assignment: remove pointless #ifdefs
  KVM: x86: merge kvm_arch_set_irq with kvm_set_msi_inatomic
  KVM: x86: zero apic_arb_prio on reset
  drivers/hv: share Hyper-V SynIC constants with userspace
  KVM: x86: handle SMBASE as physical address in RSM
  KVM: x86: add read_phys to x86_emulate_ops
  KVM: x86: removing unused variable
  KVM: don't pointlessly leave KVM_COMPAT=y in non-KVM configs
  KVM: arm/arm64: Merge vgic_set_lr() and vgic_sync_lr_elrsr()
  KVM: arm/arm64: Clean up vgic_retire_lr() and surroundings
  KVM: arm/arm64: Optimize away redundant LR tracking
  KVM: s390: use simple switch statement as multiplexer
  KVM: s390: drop useless newline in debugging data
  KVM: s390: SCA must not cross page boundaries
  KVM: arm: Do not indent the arguments of DECLARE_BITMAP
  ...
2015-11-05 16:26:26 -08:00
Pavel Fedin 26caea7693 KVM: arm/arm64: Merge vgic_set_lr() and vgic_sync_lr_elrsr()
Now we see that vgic_set_lr() and vgic_sync_lr_elrsr() are always used
together. Merge them into one function, saving from second vgic_ops
dereferencing every time.

Signed-off-by: Pavel Fedin <p.fedin@samsung.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
2015-11-04 15:29:49 +01:00
Pavel Fedin c4cd4c168b KVM: arm/arm64: Optimize away redundant LR tracking
Currently we use vgic_irq_lr_map in order to track which LRs hold which
IRQs, and lr_used bitmap in order to track which LRs are used or free.

vgic_irq_lr_map is actually used only for piggy-back optimization, and
can be easily replaced by iteration over lr_used. This is good because in
future, when LPI support is introduced, number of IRQs will grow up to at
least 16384, while numbers from 1024 to 8192 are never going to be used.
This would be a huge memory waste.

In its turn, lr_used is also completely redundant since
ae705930fc ("arm/arm64: KVM: Keep elrsr/aisr
in sync with software model"), because together with lr_used we also update
elrsr. This allows to easily replace lr_used with elrsr, inverting all
conditions (because in elrsr '1' means 'free').

Signed-off-by: Pavel Fedin <p.fedin@samsung.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
2015-11-04 15:29:49 +01:00
Michal Marek 5fdf876d30 KVM: arm: Do not indent the arguments of DECLARE_BITMAP
Besides being a coding style issue, it confuses make tags:

ctags: Warning: include/kvm/arm_vgic.h:307: null expansion of name pattern "\1"
ctags: Warning: include/kvm/arm_vgic.h:308: null expansion of name pattern "\1"
ctags: Warning: include/kvm/arm_vgic.h:309: null expansion of name pattern "\1"
ctags: Warning: include/kvm/arm_vgic.h:317: null expansion of name pattern "\1"

Cc: kvmarm@lists.cs.columbia.edu
Signed-off-by: Michal Marek <mmarek@suse.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
2015-10-22 23:01:49 +02:00
Christoffer Dall 4b4b4512da arm/arm64: KVM: Rework the arch timer to use level-triggered semantics
The arch timer currently uses edge-triggered semantics in the sense that
the line is never sampled by the vgic and lowering the line from the
timer to the vgic doesn't have any effect on the pending state of
virtual interrupts in the vgic.  This means that we do not support a
guest with the otherwise valid behavior of (1) disable interrupts (2)
enable the timer (3) disable the timer (4) enable interrupts.  Such a
guest would validly not expect to see any interrupts on real hardware,
but will see interrupts on KVM.

This patch fixes this shortcoming through the following series of
changes.

First, we change the flow of the timer/vgic sync/flush operations.  Now
the timer is always flushed/synced before the vgic, because the vgic
samples the state of the timer output.  This has the implication that we
move the timer operations in to non-preempible sections, but that is
fine after the previous commit getting rid of hrtimer schedules on every
entry/exit.

Second, we change the internal behavior of the timer, letting the timer
keep track of its previous output state, and only lower/raise the line
to the vgic when the state changes.  Note that in theory this could have
been accomplished more simply by signalling the vgic every time the
state *potentially* changed, but we don't want to be hitting the vgic
more often than necessary.

Third, we get rid of the use of the map->active field in the vgic and
instead simply set the interrupt as active on the physical distributor
whenever the input to the GIC is asserted and conversely clear the
physical active state when the input to the GIC is deasserted.

Fourth, and finally, we now initialize the timer PPIs (and all the other
unused PPIs for now), to be level-triggered, and modify the sync code to
sample the line state on HW sync and re-inject a new interrupt if it is
still pending at that time.

Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
2015-10-22 23:01:44 +02:00
Christoffer Dall d35268da66 arm/arm64: KVM: arch_timer: Only schedule soft timer on vcpu_block
We currently schedule a soft timer every time we exit the guest if the
timer did not expire while running the guest.  This is really not
necessary, because the only work we do in the timer work function is to
kick the vcpu.

Kicking the vcpu does two things:
(1) If the vpcu thread is on a waitqueue, make it runnable and remove it
from the waitqueue.
(2) If the vcpu is running on a different physical CPU from the one
doing the kick, it sends a reschedule IPI.

The second case cannot happen, because the soft timer is only ever
scheduled when the vcpu is not running.  The first case is only relevant
when the vcpu thread is on a waitqueue, which is only the case when the
vcpu thread has called kvm_vcpu_block().

Therefore, we only need to make sure a timer is scheduled for
kvm_vcpu_block(), which we do by encapsulating all calls to
kvm_vcpu_block() with kvm_timer_{un}schedule calls.

Additionally, we only schedule a soft timer if the timer is enabled and
unmasked, since it is useless otherwise.

Note that theoretically userspace can use the SET_ONE_REG interface to
change registers that should cause the timer to fire, even if the vcpu
is blocked without a scheduled timer, but this case was not supported
before this patch and we leave it for future work for now.

Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
2015-10-22 23:01:42 +02:00
Jean-Philippe Brucker 4f64cb65bf arm/arm64: KVM: Only allow 64bit hosts to build VGICv3
Hardware virtualisation of GICv3 is only supported by 64bit hosts for
the moment. Some VGICv3 bits are missing from the 32bit side, and this
patch allows to still be able to build 32bit hosts when CONFIG_ARM_GIC_V3
is selected.

To this end, we introduce a new option, CONFIG_KVM_ARM_VGIC_V3, that is
only enabled on the 64bit side. The selection is done unconditionally
because CONFIG_ARM_GIC_V3 is always enabled on arm64.

Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Jean-Philippe Brucker <jean-philippe.brucker@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
2015-10-09 23:11:57 +01:00
Ming Lei ef748917b5 arm/arm64: KVM: Remove 'config KVM_ARM_MAX_VCPUS'
This patch removes config option of KVM_ARM_MAX_VCPUS,
and like other ARCHs, just choose the maximum allowed
value from hardware, and follows the reasons:

1) from distribution view, the option has to be
defined as the max allowed value because it need to
meet all kinds of virtulization applications and
need to support most of SoCs;

2) using a bigger value doesn't introduce extra memory
consumption, and the help text in Kconfig isn't accurate
because kvm_vpu structure isn't allocated until request
of creating VCPU is sent from QEMU;

3) the main effect is that the field of vcpus[] in 'struct kvm'
becomes a bit bigger(sizeof(void *) per vcpu) and need more cache
lines to hold the structure, but 'struct kvm' is one generic struct,
and it has worked well on other ARCHs already in this way. Also,
the world switch frequecy is often low, for example, it is ~2000
when running kernel building load in VM from APM xgene KVM host,
so the effect is very small, and the difference can't be observed
in my test at all.

Cc: Dann Frazier <dann.frazier@canonical.com>
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Reviewed-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
2015-09-17 13:13:27 +01:00
Marc Zyngier f120cd6533 KVM: arm/arm64: timer: Allow the timer to control the active state
In order to remove the crude hack where we sneak the masked bit
into the timer's control register, make use of the phys_irq_map
API control the active state of the interrupt.

This causes some limited changes to allow for potential error
propagation.

Reviewed-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
2015-08-12 11:28:26 +01:00
Marc Zyngier 773299a570 KVM: arm/arm64: vgic: Prevent userspace injection of a mapped interrupt
Virtual interrupts mapped to a HW interrupt should only be triggered
from inside the kernel. Otherwise, you could end up confusing the
kernel (and the GIC's) state machine.

Rearrange the injection path so that kvm_vgic_inject_irq is
used for non-mapped interrupts, and kvm_vgic_inject_mapped_irq is
used for mapped interrupts. The latter should only be called from
inside the kernel (timer, irqfd).

Reviewed-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
2015-08-12 11:28:26 +01:00
Marc Zyngier 6e84e0e067 KVM: arm/arm64: vgic: Add vgic_{get,set}_phys_irq_active
In order to control the active state of an interrupt, introduce
a pair of accessors allowing the state to be set/queried.

This only affects the logical state, and the HW state will only be
applied at world-switch time.

Acked-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
2015-08-12 11:28:26 +01:00
Marc Zyngier 6c3d63c9a2 KVM: arm/arm64: vgic: Allow dynamic mapping of physical/virtual interrupts
In order to be able to feed physical interrupts to a guest, we need
to be able to establish the virtual-physical mapping between the two
worlds.

The mappings are kept in a set of RCU lists, indexed by virtual interrupts.

Reviewed-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
2015-08-12 11:28:25 +01:00
Marc Zyngier 32d2d8010c KVM: arm/arm64: vgic: Convert struct vgic_lr to use bitfields
As we're about to cram more information in the vgic_lr structure
(HW interrupt number and additional state information), we switch
to a layout similar to the HW's:

- use bitfields to save space (we don't need more than 10 bits
  to represent the irq numbers)
- source CPU and HW interrupt can share the same field, as
  a SGI doesn't have a physical line.

Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
2015-08-12 11:28:24 +01:00
Paolo Bonzini bf0fb67cf9 KVM/ARM changes for v4.1:
- fixes for live migration
 - irqfd support
 - kvm-io-bus & vgic rework to enable ioeventfd
 - page ageing for stage-2 translation
 - various cleanups
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v1
 
 iQIcBAABAgAGBQJVHQ0kAAoJECPQ0LrRPXpDHKQQALjw6STaZd7n20OFopNgHd4P
 qVeWYEKBxnsiSvL4p3IOSlZlEul+7x08aZqtyxWQRQcDT4ggTI+3FKKfc+8yeRpH
 WV6YJP0bGqz7039PyMLuIgs48xkSZtntePw69hPJfHZh4C1RBlP5T2SfE8mU8VZX
 fWToiU3W12QfKnmN7JFgxZopnGhrYCrG0EexdTDziAZu0GEMlDrO4wnyTR60WCvT
 4TEF73R0kpAz4yplKuhcDHuxIG7VFhQ4z7b09M1JtR0gQ3wUvfbD3Wqqi49SwHkv
 NQOStcyLsIlDosSRcLXNCwb3IxjObXTBcAxnzgm2Aoc1xMMZX1ZPQNNs6zFZzycb
 2c6QMiQ35zm7ellbvrG+bT+BP86JYWcAtHjWcaUFgqSJjb8MtqcMtsCea/DURhqx
 /kictqbPYBBwKW6SKbkNkisz59hPkuQnv35fuf992MRCbT9LAXLPRLbcirucCzkE
 p1MOotsWoO3ldJMZaVn0KYk3sQf6mCIfbYPEdOcw3fhJlvyy3NdjVkLOFbA5UUg1
 rQ7Ru2rTemBc0ExVrymngNTMpMB4XcEeJzXfhcgMl3DWbDj60Ku/O26sDtZ6bsFv
 JuDYn8FVDHz9gpEQHgiUi1YMsBKXLhnILa1ppaa6AflykU3BRfYjAk1SXmX84nQK
 mJUJEdFuxi6pHN0UKxUI
 =avA4
 -----END PGP SIGNATURE-----

Merge tag 'kvm-arm-for-4.1' of git://git.kernel.org/pub/scm/linux/kernel/git/kvmarm/kvmarm into 'kvm-next'

KVM/ARM changes for v4.1:

- fixes for live migration
- irqfd support
- kvm-io-bus & vgic rework to enable ioeventfd
- page ageing for stage-2 translation
- various cleanups
2015-04-07 18:09:20 +02:00
Andre Przywara 950324ab81 KVM: arm/arm64: rework MMIO abort handling to use KVM MMIO bus
Currently we have struct kvm_exit_mmio for encapsulating MMIO abort
data to be passed on from syndrome decoding all the way down to the
VGIC register handlers. Now as we switch the MMIO handling to be
routed through the KVM MMIO bus, it does not make sense anymore to
use that structure already from the beginning. So we keep the data in
local variables until we put them into the kvm_io_bus framework.
Then we fill kvm_exit_mmio in the VGIC only, making it a VGIC private
structure. On that way we replace the data buffer in that structure
with a pointer pointing to a single location in a local variable, so
we get rid of some copying on the way.
With all of the virtual GIC emulation code now being registered with
the kvm_io_bus, we can remove all of the old MMIO handling code and
its dispatching functionality.

I didn't bother to rename kvm_exit_mmio (to vgic_mmio or something),
because that touches a lot of code lines without any good reason.

This is based on an original patch by Nikolay.

Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Cc: Nikolay Nikolaev <n.nikolaev@virtualopensystems.com>
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
2015-03-30 17:07:19 +01:00
Andre Przywara fb8f61abab KVM: arm/arm64: prepare GICv3 emulation to use kvm_io_bus MMIO handling
Using the framework provided by the recent vgic.c changes, we
register a kvm_io_bus device on mapping the virtual GICv3 resources.
The distributor mapping is pretty straight forward, but the
redistributors need some more love, since they need to be tagged with
the respective redistributor (read: VCPU) they are connected with.
We use the kvm_io_bus framework to register one devices per VCPU.

Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
2015-03-30 17:07:13 +01:00
Andre Przywara a9cf86f62b KVM: arm/arm64: prepare GICv2 emulation to be handled by kvm_io_bus
Using the framework provided by the recent vgic.c changes we register
a kvm_io_bus device when initializing the virtual GICv2.

Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
2015-03-26 21:43:15 +00:00
Andre Przywara 6777f77f0f KVM: arm/arm64: implement kvm_io_bus MMIO handling for the VGIC
Currently we use a lot of VGIC specific code to do the MMIO
dispatching.
Use the previous reworks to add kvm_io_bus style MMIO handlers.

Those are not yet called by the MMIO abort handler, also the actual
VGIC emulator function do not make use of it yet, but will be enabled
with the following patches.

Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
2015-03-26 21:43:14 +00:00
Andre Przywara af669ac6dc KVM: move iodev.h from virt/kvm/ to include/kvm
iodev.h contains definitions for the kvm_io_bus framework. This is
needed both by the generic KVM code in virt/kvm as well as by
architecture specific code under arch/. Putting the header file in
virt/kvm and using local includes in the architecture part seems at
least dodgy to me, so let's move the file into include/kvm, so that a
more natural "#include <kvm/iodev.h>" can be used by all of the code.
This also solves a problem later when using struct kvm_io_device
in arm_vgic.h.
Fixing up the FSF address in the GPL header and a wrong include path
on the way.

Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Christoffer Dall <christoffer.dall@linaro.org>
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Reviewed-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
2015-03-26 21:43:12 +00:00
Christoffer Dall 1a74847885 arm/arm64: KVM: Fix migration race in the arch timer
When a VCPU is no longer running, we currently check to see if it has a
timer scheduled in the future, and if it does, we schedule a host
hrtimer to notify is in case the timer expires while the VCPU is still
not running.  When the hrtimer fires, we mask the guest's timer and
inject the timer IRQ (still relying on the guest unmasking the time when
it receives the IRQ).

This is all good and fine, but when migration a VM (checkpoint/restore)
this introduces a race.  It is unlikely, but possible, for the following
sequence of events to happen:

 1. Userspace stops the VM
 2. Hrtimer for VCPU is scheduled
 3. Userspace checkpoints the VGIC state (no pending timer interrupts)
 4. The hrtimer fires, schedules work in a workqueue
 5. Workqueue function runs, masks the timer and injects timer interrupt
 6. Userspace checkpoints the timer state (timer masked)

At restore time, you end up with a masked timer without any timer
interrupts and your guest halts never receiving timer interrupts.

Fix this by only kicking the VCPU in the workqueue function, and sample
the expired state of the timer when entering the guest again and inject
the interrupt and mask the timer only then.

Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
2015-03-14 13:48:00 +01:00
Christoffer Dall 47a98b15ba arm/arm64: KVM: support for un-queuing active IRQs
Migrating active interrupts causes the active state to be lost
completely. This implements some additional bitmaps to track the active
state on the distributor and export this to user space.

Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
2015-03-14 13:46:44 +01:00
Christoffer Dall ae705930fc arm/arm64: KVM: Keep elrsr/aisr in sync with software model
There is an interesting bug in the vgic code, which manifests itself
when the KVM run loop has a signal pending or needs a vmid generation
rollover after having disabled interrupts but before actually switching
to the guest.

In this case, we flush the vgic as usual, but we sync back the vgic
state and exit to userspace before entering the guest.  The consequence
is that we will be syncing the list registers back to the software model
using the GICH_ELRSR and GICH_EISR from the last execution of the guest,
potentially overwriting a list register containing an interrupt.

This showed up during migration testing where we would capture a state
where the VM has masked the arch timer but there were no interrupts,
resulting in a hung test.

Cc: Marc Zyngier <marc.zyngier@arm.com>
Reported-by: Alex Bennee <alex.bennee@linaro.org>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
2015-03-14 13:42:07 +01:00
Christoffer Dall 662d971584 arm/arm64: KVM: Kill CONFIG_KVM_ARM_{VGIC,TIMER}
We can definitely decide at run-time whether to use the GIC and timers
or not, and the extra code and data structures that we allocate space
for is really negligable with this config option, so I don't think it's
worth the extra complexity of always having to define stub static
inlines.  The !CONFIG_KVM_ARM_VGIC/TIMER case is pretty much an untested
code path anyway, so we're better off just getting rid of it.

Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
2015-03-12 15:15:27 +01:00
Andre Przywara ac3d373564 arm/arm64: KVM: allow userland to request a virtual GICv3
With all of the GICv3 code in place now we allow userland to ask the
kernel for using a virtual GICv3 in the guest.
Also we provide the necessary support for guests setting the memory
addresses for the virtual distributor and redistributors.
This requires some userland code to make use of that feature and
explicitly ask for a virtual GICv3.
Document that KVM_CREATE_IRQCHIP only works for GICv2, but is
considered legacy and using KVM_CREATE_DEVICE is preferred.

Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
2015-01-20 18:25:33 +01:00
Andre Przywara b5d84ff600 arm/arm64: KVM: enable kernel side of GICv3 emulation
With all the necessary GICv3 emulation code in place, we can now
connect the code to the GICv3 backend in the kernel.
The LR register handling is different depending on the emulated GIC
model, so provide different implementations for each.
Also allow non-v2-compatible GICv3 implementations (which don't
provide MMIO regions for the virtual CPU interface in the DT), but
restrict those hosts to support GICv3 guests only.
If the device tree provides a GICv2 compatible GICV resource entry,
but that one is faulty, just disable the GICv2 emulation and let the
user use at least the GICv3 emulation for guests.
To provide proper support for the legacy KVM_CREATE_IRQCHIP ioctl,
note virtual GICv2 compatibility in struct vgic_params and use it
on creating a VGICv2.

Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
2015-01-20 18:25:32 +01:00
Andre Przywara 6d52f35af1 arm64: KVM: add SGI generation register emulation
While the generation of a (virtual) inter-processor interrupt (SGI)
on a GICv2 works by writing to a MMIO register, GICv3 uses the system
register ICC_SGI1R_EL1 to trigger them.
Add a trap handler function that calls the new SGI register handler
in the GICv3 code. As ICC_SRE_EL1.SRE at this point is still always 0,
this will not trap yet, but will only be used later when all the data
structures have been initialized properly.

Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
2015-01-20 18:25:32 +01:00
Andre Przywara a0675c25d6 arm/arm64: KVM: add virtual GICv3 distributor emulation
With everything separated and prepared, we implement a model of a
GICv3 distributor and redistributors by using the existing framework
to provide handler functions for each register group.

Currently we limit the emulation to a model enforcing a single
security state, with SRE==1 (forcing system register access) and
ARE==1 (allowing more than 8 VCPUs).

We share some of the functions provided for GICv2 emulation, but take
the different ways of addressing (v)CPUs into account.
Save and restore is currently not implemented.

Similar to the split-off of the GICv2 specific code, the new emulation
code goes into a new file (vgic-v3-emul.c).

Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
2015-01-20 18:25:31 +01:00
Andre Przywara 2f5fa41a7a arm/arm64: KVM: make the value of ICC_SRE_EL1 a per-VM variable
ICC_SRE_EL1 is a system register allowing msr/mrs accesses to the
GIC CPU interface for EL1 (guests). Currently we force it to 0, but
for proper GICv3 support we have to allow guests to use it (depending
on their selected virtual GIC model).
So add ICC_SRE_EL1 to the list of saved/restored registers on a
world switch, but actually disallow a guest to change it by only
restoring a fixed, once-initialized value.
This value depends on the GIC model userland has chosen for a guest.

Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Christoffer Dall <christoffer.dall@linaro.org>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
2015-01-20 18:25:28 +01:00
Andre Przywara 3caa2d8c3b arm/arm64: KVM: make the maximum number of vCPUs a per-VM value
Currently the maximum number of vCPUs supported is a global value
limited by the used GIC model. GICv3 will lift this limit, but we
still need to observe it for guests using GICv2.
So the maximum number of vCPUs is per-VM value, depending on the
GIC model the guest uses.
Store and check the value in struct kvm_arch, but keep it down to
8 for now.

Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
2015-01-20 18:25:28 +01:00
Andre Przywara b26e5fdac4 arm/arm64: KVM: introduce per-VM ops
Currently we only have one virtual GIC model supported, so all guests
use the same emulation code. With the addition of another model we
end up with different guests using potentially different vGIC models,
so we have to split up some functions to be per VM.
Introduce a vgic_vm_ops struct to hold function pointers for those
functions that are different and provide the necessary code to
initialize them.
Also split up the vgic_init() function to separate out VGIC model
specific functionality into a separate function, which will later be
different for a GICv3 model.

Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
2015-01-20 18:25:26 +01:00
Andre Przywara 59892136c4 arm/arm64: KVM: pass down user space provided GIC type into vGIC code
With the introduction of a second emulated GIC model we need to let
userspace specify the GIC model to use for each VM. Pass the
userspace provided value down into the vGIC code and store it there
to differentiate later.

Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Christoffer Dall <christoffer.dall@linaro.org>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
2015-01-20 18:25:25 +01:00