While merging data_xfer prototype change, pata_pcmcia was left out.
Convert it.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
libata-sff code used DRV_NAME which is hardcoded to "libata" when
requesting resources. Use dev_driver_string() such that low level
driver names are used in resource listing.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Kill PIIX_FLAG_SCR, PIIX_PORT_ENABLED and PIIX_PORT_PRESENT. These
are unused.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
ata_port_queue_task() served a single user: ata_pio_task()
Rename to ata_pio_queue_task() and un-export it, as nobody outside of
libata-core.c uses it.
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Some it821x RAID firmwares return 0 for the err return off both devices.
A similar issue occurs with the slave returning 0 not 1 if you plug a
gigabyte sata ramdisk into a controller that fakes two SATA ports as
master/slave on an SFF channel.
The patch does the following
- Allow the 'failed diagnostics' case on both master and slave
- Move the HORKAGE_DIAGNOSTIC check after ->dev_config
This second change also allows IT821x to fix up a problem where we report
drive diagnostic failures when in fact the drive is fine but the
microcontroller firmware doesn't appear to get it right. IT821x clears
the flag again to avoid giving the user bogus warnings about their disk.
The other IT821x change is a bit ugly, we slightly abuse the cable type
hook to fiddle with the identify data for the devices. We could add a new
hook for this but as we have only one offender and no more seeming likely
it seems better to keep libata-core clean.
Please let this sit in -mm briefly, just in case the relaxed checking
breaks some other emulated interface.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
qc->nbytes didn't use to include extra buffers setup by libata core
layer and my be odd. This patch makes qc->nbytes include any extra
buffers setup by libata core layer and guaranteed to be aligned on 4
byte boundary.
This value is to be used to program the host controller. As this
represents the actual length of buffer available to the controller and
the controller must be able to deal with short transfers for ATAPI
commands which can transfer variable length, this shouldn't break any
controllers while making problems like rounding-down and controllers
choking up on odd transfer bytes much less likely.
The unmodified value is stored in new field qc->raw_nbytes.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
libata used private sg iterator to handle padding sg. Now that sg can
be chained, padding can be handled using standard sg ops. Convert to
chained sg.
* s/qc->__sg/qc->sg/
* s/qc->pad_sgent/qc->extra_sg[]/. Because chaining consumes one sg
entry. There need to be two extra sg entries. The renaming is also
for future addition of other extra sg entries.
* Padding setup is moved into ata_sg_setup_extra() which is organized
in a way that future addition of other extra sg entries is easy.
* qc->orig_n_elem is unused and removed.
* qc->n_elem now contains the number of sg entries that LLDs should
map. qc->mapped_n_elem is added to carry the original number of
mapped sgs for unmapping.
* The last sg of the original sg list is used to chain to extra sg
list. The original last sg is pointed to by qc->last_sg and the
content is stored in qc->saved_last_sg. It's restored during
ata_sg_clean().
* All sg walking code has been updated. Unnecessary assertions and
checks for conditions the core layer already guarantees are removed.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Jens Axboe <jens.axboe@oracle.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
ATA_QCFLAG_DMAMAP was a bit peculiar in that it got set during qc
initialization and cleared if DMA mapping wasn't necessary. Make it
more straight forward by making the following changes.
* Don't set it during initialization. Set it after DMA is actually
mapped.
* Add BUG_ON() to guarantee that there is data to transfer if DMAMAP
is set. This always holds for the current code. The BUG_ON() is
for docummentation and sanity check.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
With atapi_request_sense() converted to use sg, there's no user of
non-sg interface. Kill non-sg interface.
* ATA_QCFLAG_SINGLE and ATA_QCFLAG_SG are removed. ATA_QCFLAG_DMAMAP
is used instead. (this way no LLD change is necessary)
* qc->buf_virt is removed.
* ata_sg_init_one() and ata_sg_setup_one() are removed.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Rusty Russel <rusty@rustcorp.com.au>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Depending on how many bytes are transferred as a unit, PIO data
transfer may consume more bytes than requested. Knowing how much
data is consumed is necessary to determine how much is left for
draining. This patch update ->data_xfer such that it returns the
number of consumed bytes.
While at it, it also makes the following changes.
* s/adev/dev/
* use READ/WRITE constants for rw indication
* misc clean ups
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
ATA_PROT_ATAPI_* are ugly and naming schemes between ATA_PROT_* and
ATA_PROT_ATAPI_* are inconsistent causing confusion. Rename them to
ATAPI_PROT_* and make them consistent with ATA counterpart.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Treat zero xfer length as HSM violation. While at it, add
unlikely()'s to ATAPI ireason and transfer length checks.
tj: Formatted patch and added unlikely()'s.
Signed-off-by: Albert Lee <albertcc@tw.ibm.com>
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
atapi_request_sense() is now the only left user of ata_sg_init_one().
Convert it to use sg interface.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Rusty Russel <rusty@rustcorp.com.au>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
I missed one while converting to ata_is_*() protocol test helpers.
Convert it. Pointed out by Jeff Garzik.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
WARNING: line over 80 characters
#70: FILE: drivers/ata/pata_hpt37x.c:850:
+ struct pci_dev *pdev_0 = pci_get_slot(pdev->bus, pdev->devfn - 1);
ERROR: else should follow close brace '}'
#78: FILE: drivers/ata/pata_hpt37x.c:858:
+ }
+ else
total: 1 errors, 1 warnings, 100 lines checked
Your patch has style problems, please review. If any of these errors
are false positives report them to the maintainer, see
CHECKPATCH in MAINTAINERS.
Please run checkpatch prior to sending patches
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
drivers/ata/libata-eh.c: In function `ata_port_pbar_desc':
drivers/ata/libata-eh.c:215: warning: long long unsigned int format, long unsigned int arg (arg 4)
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Cable detection on NV PATA hosts isn't implemented and the CBLID-
cable isn't wired according to the sepc either, so both host-side and
generic drive-side cable detections are broken. Till now,
nv_cable_detect() relied on peeking BIOS and ACPI configurations to
upgrade to 80C but this often results in misdetection of 40C cable as
80C. Also, the original implementation was broken in that by the time
BIOS configuration is read it has already been cleared by programming
PIO0 during reset.
This patch reimplements NV mode selection such that...
* BIOS configuration value is stored during driver attach and restored
on detach.
* Cable type is fixed to ATA_CBL_PATA_IGN and mode selection is soley
done by nv_mode_filter() which peeks both BIOS and ACPI
configurations and filter accordingly.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Reimplement ata_acpi_cbl_80wire() using ata_acpi_gtm_xfermask() and
while at it relocate the function below ata_acpi_gtm_xfermask().
New ata_acpi_cbl_80wire() implementation takes @gtm, in both pata_via
and pata_amd, use the initial GTM value. Both are trying to peek
initial BIOS configuration, so using initial caching value makes
sense. This fixes ACPI part of cable detection in pata_amd which
previously always returned 0 because configuring PIO0 during reset
clears DMA configuration.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
libata-acpi is using separate timing tables for transfer modes
although libata-core has the complete ata_timing table. Implement
ata_timing_cycle2mode() to look for matching mode given transfer type
and cycle duration and use it in libata-acpi and pata_acpi to replace
private timing tables.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
ata_acpi_gtm_xfermask() as separated out from pacpi_discover_modes()
has various bugs. Fix them.
* The wrong comparison operator is used when finding for matching
cycle resulting totally bogus result.
* With the comparion operator fixed, boundary condtion handling is
clumsy.
* Setting of any DMA mask bit set all bits in PIO mask.
* MWDMA and UDMA blocks are swapped.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Finding out matching transfer mode from ACPI GTM values is useful for
other purposes too. Separate out the function and timing tables from
pata_acpi::pacpi_discover_modes().
Other than checking shared-configuration bit after doing
ata_acpi_gtm() in pacpi_discover_modes() which should be safe, this
patch doesn't introduce any behavior change.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Separate controller IDs into a separate enum as Jeff requested.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Make pdc_atapi_pkt() use values from qc->tf instead of creating its
own. This is to ease future ATAPI handling changes.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Mikael Pettersson <mikpe@it.uu.se>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
ATA_CBL_PATA_UNK indicates that the cable type can't be determined
from the host side and might be either 80c or 40c. libata applies
drive or other generic limit in this case. However, there are
controllers where both host and drive side detections are
misimplemented and the driver has to rely solely on private method -
peeking BIOS or ACPI configuration or using some other private
mechanism.
This patch adds ATA_CBL_PATA_IGN which tells libata to ignore the
cable type completely and just let the LLD determine the transfer mode
via host transfer mode masks and ->mode_filter().
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Jeff says xfer_mask is unsigned long not unsigned int. Convert all
xfermask fields and handling functions to deal with unsigned longs.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
ata_id_to_dma_mode() isn't quite generic. The function is basically
privately implemented ata_id_xfermask() combined with hardcoded mode
printing and configuration which are specific to ata_generic.
Kill the function and open code it in generic_set_mode() using generic
xfermode handling functions.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
* s/ATA_BITS_(PIO|MWDMA|UDMA)/ATA_NR_\1_MODES/g
* Consistently use 0xff to indicate invalid transfer mode (0x00 is
valid for PIO_SLOW).
* Make ata_xfer_mode2mask() return proper mode mask instead of just
the highest bit.
* Sort ata_timing table in increasing xfermode order and update
ata_timing_find_mode() accordingly.
This patch doesn't introduce any behavior change.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Export the following xfermode related functions.
* ata_pack_xfermask()
* ata_unpack_xfermask()
* ata_xfer_mask2mode()
* ata_xfer_mode2mask()
* ata_xfer_mode2shift()
* ata_mode_string()
* ata_id_xfermask()
* ata_timing_find_mode()
These functions will be used later by LLD updates. While at it,
change unsigned short @speed to u8 @xfer_mode in
ata_timing_find_mode() for consistency.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Unindent loop body in generic_set_mode(). This is to ease future
change.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
It's very likely that the configured data transfer mode is the wrong
one if device fails data transfers right after initial data transfer
mode configuration (including NCQ on/off and xfermode). libata EH
needs to speed down fast before upper layers give up on probing.
This patch implement fast speed down rules to handle such cases
better. Error occured while data transfer hasn't been verified
trigger fast back-to-back speed down actions until data transfer
works.
This change will make cable mis-detection and other initial
configuration problems corrected before partition scanning code gives
up.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
ATA_DFLAG_DUBIOUS_XFER is set whenever data transfer speed or method
changes and gets cleared when data transfer command succeeds in the
newly configured transfer mode.
This will be used to improve speed down logic.
Signed-off-by: Tejun Heo <htejun@gmail.com<
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Speed down rules were too conservative. Adjust them a bit.
* More than 10 timeouts can't happen in 5 minutes as command timeout
is 30secs. Lower the limit for rule #1 to 6.
* 10 timeouts is too high for rule #3 too. Lower it to 6.
* SATAPI can benefit from falling back to PIO too. Allow SATAPI
devices to fall back to PIO.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Clean up EH speed down implementation.
* is_io boolean variable is replaced eflags. is_io is ATA_EFLAG_IS_IO.
* Error categories now have names.
* Better comments.
* Reorder 5min and 10min rules in ata_eh_speed_down_verdict()
* Use local variable @link to cache @dev->link in ata_eh_speed_down()
These changes are to improve readability and ease further changes.
This patch doesn't introduce any behavior change.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Move ata_set_mode() to libata-eh.c. ata_set_mode() is surely an EH
action and will be more tightly coupled with the rest of error
handling. Move it to libata-eh.c.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Factor out ata_eh_schedule_probe() from ata_eh_handle_dev_fail() and
ata_eh_recover(). This is to improve maintainability and make future
changes easier.
In the previous revision, ata_dev_enabled() test was accidentally
dropped while factoring out. This problem was spotted by Bartlomiej.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Implement protocol tests - ata_is_atapi(), ata_is_nodata(),
ata_is_pio(), ata_is_dma(), ata_is_ncq() and ata_is_data() and use
them to replace is_atapi_taskfile() and hard coded protocol tests.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
For intel ones, ahci unconditionally OR'd 0xf to PCS. This isn't
correct for the following cases.
* ich6/7m's which only implement P0 and P2 (0xf works fine tho)
* ich8/9's which have six ports and needs 0x3f to enable all ports
This patch updates PCS programming such that...
* port_map determined by ahci_save_initial_config() is OR'd instead of 0xf
* PCS is updated only if necessary (there are turned off enable bits)
port_map is determined from PORTS_IMPL PCI register which is
implemented as write or write-once register. If the register isn't
programmed, ahci automatically generates it from number of ports,
which is good enough for PCS programming. ICH6/7M are probably the
only ones where non-contiguous enable bits are necessary && PORTS_IMPL
isn't programmed properly but they're proven to work reliably with 0xf
anyway.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Lots of work needed to bring it up to scratch but it does work so you can
now use the card. That makes it at least useful, especially as the other
cardbus cards are usually INIC162x which aren't yet supported well.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Jeff said he preferred that the SFF tf_load followed the spec and we
documented that anyone who needed different overrode it, rather than it
using the ->check_status methods. No driver relies on the current behaviour.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
I believe this version meets all Sergei's objections
Correct the logic for when we issue a set features for transfer mode
- If the device has IORDY and the controller has IORDY - set the mode
- If the device has IORDY and the controller does not - turn IORDY off
- If neither has IORDY do nothing
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
ACPI spec (ver 3.0a, p289) requires IDE power on/off executes ACPI _PSx
methods. As recently most PATA drivers use libata, this patch adds _PSx
method support in libata. ACPI spec doesn't mention if SATA requires the
same _PSx method.
Signed-off-by: Shaohua Li <shaohua.li@intel.com>
Acked-by: Len Brown <len.brown@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Historically word 48 in the identify data was used to mean 32bit I/O
was supported for VLB IDE etc. ATA8 reassigns this word to the Trusted
Computing Group, where it is used for TCG features. This means that
an ATA8 TCG drive is going to trigger 32bit I/O on some systems which
will be funny.
Anyway we need to sort this out ready for ATA8 so:
- Reorder the ata.h header a bit so the ata_version function occurs early
in it
- Make dword_io check the ATA version
- Add an ATA8 version checking TCG presence test
While we are at it the current drafts have a flaw where it may not be
possible to disable TCG features at boot (and opt out of the trusted
model) as TCG intends because it relies on presence of a different
optional feature (DCS). Handle this in software by refusing the TCG
commands if libata.allow_tpm is not set. (We must make it possible
as some environments such as proprietary VDR devices will doubtless
want to use it to lock up content)
Finally as with CPRM print a warning so that the user knows they may
not be able to full access and use the device.
Signed-off-by: Alan Cox <alan@redhat.com>
Add Toshiba Satellite R20 and Tecra M6 to broken suspend list. Matt
Piermarini reported and provided the M6 patch. This is from OSDL bug 7780.
Signed-off-by: Peter Schwenke <peter@bluetoad.com.au>
Cc: Matt Piermarini <mattpiermarini@yahoo.com>
Acked-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The PDC202xx older devices do not support ATAPI DMA via the usual
interfaces. What documentation I have isn't sufficient to support DMA and
it isn't clear if the Windows drivers do this or it is possible at all.
(Neither do the drivers/ide old drivers)
So turn it ATAPI DMA off, these are disk optimised controllers.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: Tejun Heo <htejun@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
