When btrfs_get_extent is reading inline file items for readpage,
it needs to copy the inline extent into the page. If the
inline extent doesn't cover all of the page, that means there
is a hole in the file, or that our file is smaller than one
page.
readpage does zeroing for the case where the file is smaller than one
page, but nobody is currently zeroing for the case where there is
a hole after the inline item.
This commit changes btrfs_get_extent to zero fill the page past
the end of the inline item.
Signed-off-by: Chris Mason <chris.mason@oracle.com>
This closes a whole where the page may be written before
the page_mkwrite caller has a chance to dirty it
(thanks to Nick Piggin)
Signed-off-by: Chris Mason <chris.mason@oracle.com>
Data COW means that whenever we write to a file, we replace any old
extent pointers with new ones. There was a window where a readpage
might find the old extent pointers on disk and cache them in the
extent_map tree in ram in the middle of a given write replacing them.
Even though both the readpage and the write had their respective bytes
in the file locked, the extent readpage inserts may cover more bytes than
it had locked down.
This commit closes the race by keeping the new extent pinned in the extent
map tree until after the on-disk btree is properly setup with the new
extent pointers.
Signed-off-by: Chris Mason <chris.mason@oracle.com>
Btrfs writes go through delalloc to the data=ordered code. This
makes sure that all of the data is on disk before the metadata
that references it. The tracking means that we have to make sure
each page in an extent is fully written before we add that extent into
the on-disk btree.
This was done in the past by setting the EXTENT_ORDERED bit for the
range of an extent when it was added to the data=ordered code, and then
clearing the EXTENT_ORDERED bit in the extent state tree as each page
finished IO.
One of the reasons we had to do this was because sometimes pages are
magically dirtied without page_mkwrite being called. The EXTENT_ORDERED
bit is checked at writepage time, and if it isn't there, our page become
dirty without going through the proper path.
These bit operations make for a number of rbtree searches for each page,
and can cause considerable lock contention.
This commit switches from the EXTENT_ORDERED bit to use PagePrivate2.
As pages go into the ordered code, PagePrivate2 is set on each one.
This is a cheap operation because we already have all the pages locked
and ready to go.
As IO finishes, the PagePrivate2 bit is cleared and the ordered
accoutning is updated for each page.
At writepage time, if the PagePrivate2 bit is missing, we go into the
writepage fixup code to handle improperly dirtied pages.
Signed-off-by: Chris Mason <chris.mason@oracle.com>
This changes the btrfs code to find delalloc ranges in the extent state
tree to use the new state caching code from set/test bit. It reduces
one of the biggest causes of rbtree searches in the writeback path.
test_range_bit is also modified to take the cached state as a starting
point while searching.
Signed-off-by: Chris Mason <chris.mason@oracle.com>
At writepage time, we have the page locked and we have the
extent_map entry for this extent pinned in the extent_map tree.
So, the page can't go away and its mapping can't change.
There is no need for the extra extent_state lock bits during writepage.
Signed-off-by: Chris Mason <chris.mason@oracle.com>
Many of the btrfs extent state tree users follow the same pattern.
They lock an extent range in the tree, do some operation and then
unlock.
This translates to at least 2 rbtree searches, and maybe more if they
are doing operations on the extent state tree. A locked extent
in the tree isn't going to be merged or changed, and so we can
safely return the extent state structure as a cached handle.
This changes set_extent_bit to give back a cached handle, and also
changes both set_extent_bit and clear_extent_bit to use the cached
handle if it is available.
Signed-off-by: Chris Mason <chris.mason@oracle.com>
Btrfs is currently mirroring some of the page state bits into
its extent state tree. The goal behind this was to use it in supporting
blocksizes other than the page size.
But, we don't currently support that, and we're using quite a lot of CPU
on the rb tree and its spin lock. This commit starts a series of
cleanups to reduce the amount of work done in the extent state tree as
part of each IO.
This commit:
* Adds the ability to lock an extent in the state tree and also set
other bits. The idea is to do locking and delalloc in one call
* Removes the EXTENT_WRITEBACK and EXTENT_DIRTY bits. Btrfs is using
a combination of the page bits and the ordered write code for this
instead.
Signed-off-by: Chris Mason <chris.mason@oracle.com>
As the extent state tree is manipulated, there are call backs
that are used to take extra actions when different state bits are set
or cleared. One example of this is a counter for the total number
of delayed allocation bytes in a single inode and in the whole FS.
When new states are inserted, this callback is being done before we
properly setup the new state. This hasn't caused problems before
because the lock bit was always done first, and the existing call backs
don't care about the lock bit.
This patch makes sure the state is properly setup before using the
callback, which is important for later optimizations that do more work
without using the lock bit.
Signed-off-by: Chris Mason <chris.mason@oracle.com>
There are two main users of the extent_map tree. The
first is regular file inodes, where it is evenly spread
between readers and writers.
The second is the chunk allocation tree, which maps blocks from
logical addresses to phyiscal ones, and it is 99.99% reads.
The mapping tree is a point of lock contention during heavy IO
workloads, so this commit switches things to a rw lock.
Signed-off-by: Chris Mason <chris.mason@oracle.com>
The btrfs io submission thread tries to back off congested devices in
favor of rotating off to another disk.
But, it tries to make sure it submits at least some IO before rotating
on (the others may be congested too), and so it has a magic number of
requests it tries to write before it hops.
This makes the magic number smaller. Testing shows that we're spending
too much time on congested devices and leaving the other devices idle.
Signed-off-by: Chris Mason <chris.mason@oracle.com>
When btrfs fills a large delayed allocation extent, it is a good idea
to try and convince the write_cache_pages caller to go ahead and
write a good chunk of that extent. The extra IO is basically free
because we know it is contiguous.
Signed-off-by: Chris Mason <chris.mason@oracle.com>
This changes the btrfs worker threads to batch work items
into a local list. It allows us to pull work items in
large chunks and significantly reduces the number of times we
need to take the worker thread spinlock.
Signed-off-by: Chris Mason <chris.mason@oracle.com>
The btrfs worker thread spinlock was being used both for the
queueing of IO and for the processing of ordered events.
The ordered events never happen from end_io handlers, and so they
don't need to use the _irq version of spinlocks. This adds a
dedicated lock to the ordered lists so they don't have to run
with irqs off.
Signed-off-by: Chris Mason <chris.mason@oracle.com>
The Btrfs set_extent_bit call currently searches the rbtree
every time it needs to find more extent_state objects to fill
the requested operation.
This adds a simple test with rb_next to see if the next object
in the tree was adjacent to the one we just found. If so,
we skip the search and just use the next object.
Signed-off-by: Chris Mason <chris.mason@oracle.com>
The Btrfs worker threads don't currently die off after they have
been idle for a while, leading to a lot of threads sitting around
doing nothing for each mount.
Also, they are unable to start atomically (from end_io hanlders).
This commit reworks the worker threads so they can be started
from end_io handlers (just setting a flag that asks for a thread
to be added at a later date) and so they can exit if they
have been idle for a long time.
Signed-off-by: Chris Mason <chris.mason@oracle.com>
Get rid of any functions that test for these bits and make callers
use bio_rw_flagged() directly. Then it is at least directly apparent
what variable and flag they check.
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
This enables us to track who does what and print info. Its main use
is catching dirty inodes on the default_backing_dev_info, so we can
fix that up.
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Node may not be inserted over existing node. This causes inode tree
corruption and I was seeing crashes in inode_tree_del which I can not
reproduce after this patch.
The other way to fix this would be to tie inode lifetime in the rbtree
with inode while not in freeing state. I had a look at this but it is
not so trivial at this point. At least this patch gets things working again.
Signed-off-by: Nick Piggin <npiggin@suse.de>
Cc: Chris Mason <chris.mason@oracle.com>
Acked-by: Yan Zheng <zheng.yan@oracle.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
invalidate_inode_pages2_range may return -EBUSY occasionally
which results Oops. This patch fixes the issue by moving
invalidate_inode_pages2_range into a loop and keeping calling
it until the return value is not -EBUSY.
The EBUSY return is temporary, and can happen when the btrfs release page
function is unable to release a page because the EXTENT_LOCK
bit is set.
Signed-off-by: Yan Zheng <zheng.yan@oracle.com>
Signed-off-by: Chris Mason <chris.mason@oracle.com>
find_zlib_workspace returns an ERR_PTR value in an error case instead of NULL.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@match exists@
expression x, E;
statement S1, S2;
@@
x = find_zlib_workspace(...)
... when != x = E
(
* if (x == NULL || ...) S1 else S2
|
* if (x == NULL && ...) S1 else S2
)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Chris Mason <chris.mason@oracle.com>
This takes care of the following entry from Dan's list:
fs/btrfs/inode.c +4788 btrfs_rename(36) warning: variable derefenced before check 'old_inode'
Reported-by: Dan Carpenter <error27@gmail.com>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Eugene Teo <eteo@redhat.com>
Cc: Julia Lawall <julia@diku.dk>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Chris Mason <chris.mason@oracle.com>
The async caching thread can end up looping forever if a given
search puts it at the last key in a leaf. It will end up calling
btrfs_next_leaf and then checking if it needs to politely drop
the read semaphore.
Most of the time this looping isn't noticed because it is able to
make progress the next time around. But, during log replay,
we wait on the async caching thread to finish, and the async thread
is waiting on the commit, and no progress is really made.
The fix used here is to copy the key out of the next leaf,
that way our search lands there properly.
Signed-off-by: Chris Mason <chris.mason@oracle.com>
Yan Zheng hit a problem where we tried to remove some free space but failed
because we couldn't find the free space entry. This is because the free space
was held within a bitmap that had a starting offset well before the actual
offset of the free space, and there were free space extents that were in the
same range as that offset, so tree_search_offset returned with NULL because we
couldn't find a free space extent that had that offset. This is fixed by
making sure that if we fail to find the entry, we re-search again with
bitmap_only set to 1 and do an offset_to_bitmap so we can get the appropriate
bitmap. A similar problem happens in btrfs_alloc_from_bitmap for the
clustering code, but that is not as bad since we will just go and redo our
cluster allocation.
Also this adds some debugging checks to make sure that the free space we are
trying to remove from the bitmap is in fact there. This can probably go away
after a while, but since this code is only used by the tree-logging stuff it
would be nice to run with it for a while to make sure there are no problems.
Signed-off-by: Josef Bacik <jbacik@redhat.com>
Signed-off-by: Chris Mason <chris.mason@oracle.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/mason/btrfs-unstable:
Btrfs: be more polite in the async caching threads
Btrfs: preserve commit_root for async caching
The semaphore used by the async caching threads can prevent a
transaction commit, which can make the FS appear to stall. This
releases the semaphore more often when a transaction commit is
in progress.
Signed-off-by: Chris Mason <chris.mason@oracle.com>
The async block group caching code uses the commit_root pointer
to get a stable version of the extent allocation tree for scanning.
This copy of the tree root isn't going to change and it significantly
reduces the complexity of the scanning code.
During a commit, we have a loop where we update the extent allocation
tree root. We need to loop because updating the root pointer in
the tree of tree roots may allocate blocks which may change the
extent allocation tree.
Right now the commit_root pointer is changed inside this loop. It
is more correct to change the commit_root pointer only after all the
looping is done.
Signed-off-by: Yan Zheng <zheng.yan@oracle.com>
Signed-off-by: Chris Mason <chris.mason@oracle.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/mason/btrfs-unstable: (22 commits)
Btrfs: Fix async caching interaction with unmount
Btrfs: change how we unpin extents
Btrfs: Correct redundant test in add_inode_ref
Btrfs: find smallest available device extent during chunk allocation
Btrfs: clear all space_info->full after removing a block group
Btrfs: make flushoncommit mount option correctly wait on ordered_extents
Btrfs: Avoid delayed reference update looping
Btrfs: Fix ordering of key field checks in btrfs_previous_item
Btrfs: find_free_dev_extent doesn't handle holes at the start of the device
Btrfs: Remove code duplication in comp_keys
Btrfs: async block group caching
Btrfs: use hybrid extents+bitmap rb tree for free space
Btrfs: Fix crash on read failures at mount
Btrfs: remove of redundant btrfs_header_level
Btrfs: adjust NULL test
Btrfs: Remove broken sanity check from btrfs_rmap_block()
Btrfs: convert nested spin_lock_irqsave to spin_lock
Btrfs: make sure all dirty blocks are written at commit time
Btrfs: fix locking issue in btrfs_find_next_key
Btrfs: fix double increment of path->slots[0] in btrfs_next_leaf
...
- don't stop the caching thread until btrfs_commit_super return.
- if caching is interrupted by umount, set last to (u64)-1.
otherwise the un-scanned range of block group will be considered
as free extent.
Signed-off-by: Chris Mason <chris.mason@oracle.com>
We are racy with async block caching and unpinning extents. This patch makes
things much less complicated by only unpinning the extent if the block group is
cached. We check the block_group->cached var under the block_group->lock spin
lock. If it is set to BTRFS_CACHE_FINISHED then we update the pinned counters,
and unpin the extent and add the free space back. If it is not set to this, we
start the caching of the block group so the next time we unpin extents we can
unpin the extent. This keeps us from racing with the async caching threads,
lets us kill the fs wide async thread counter, and keeps us from having to set
DELALLOC bits for every extent we hit if there are caching kthreads going.
One thing that needed to be changed was btrfs_free_super_mirror_extents. Now
instead of just looking for LOCKED extents, we also look for DIRTY extents,
since we could have left some extents pinned in the previous transaction that
will never get freed now that we are unmounting, which would cause us to leak
memory. So btrfs_free_super_mirror_extents has been changed to
btrfs_free_pinned_extents, and it will clear the extents locked for the super
mirror, and any remaining pinned extents that may be present. Thank you,
Signed-off-by: Josef Bacik <jbacik@redhat.com>
Signed-off-by: Chris Mason <chris.mason@oracle.com>
dir has already been tested. It seems that this test should be on the
recently returned value inode.
A simplified version of the semantic match that finds this problem is as
follows: (http://www.emn.fr/x-info/coccinelle/)
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Chris Mason <chris.mason@oracle.com>
Allocating new block group is easy when the disk has plenty of space.
But things get difficult as the disk fills up, especially if
the FS has been run through btrfs-vol -b. The balance operation
is likely to make the total bytes available on the device greater
than the largest extent we'll actually be able to allocate.
But the device extent allocation code incorrectly assumes that a device
with 5G free will be able to allocate a 5G extent. It isn't normally a
problem because device extents don't get freed unless btrfs-vol -b
is run.
This fixes the device extent allocator to remember the largest free
extent it can find, and then uses that value as a fallback.
Signed-off-by: Chris Mason <chris.mason@oracle.com>
Btrfs allocates individual extents from block groups, and each
block group has a specific type. It may hold metadata, data
mirrored or striped etc.
When we balance space (btrfs-vol -b) or remove a drive (btrfs-vol -r)
we free block groups. Once a block group is freed, the space it was
using on the device may be available for use by new block groups.
btrfs_remove_block_group was clearing the flag that said
'our devices are full, don't even try to allocate new block groups',
but it was only clearing that flag for a specific type of block group.
This commit clears the full flag for all of the types of block groups,
making it much more likely that we'll be able to balance space when
the drive is close to full.
Signed-off-by: Chris Mason <chris.mason@oracle.com>
The commit_transaction call to wait_ordered_extents when snap_pending
passes nocow_only=1 to process only NOCOW or PREALLOC extents. This isn't
correct for the 'flushoncommit' mode, as it skips extents we just started
IO on in start_delalloc_inodes.
So, in the flushoncommit case, wait on all ordered extents. Otherwise,
only pass the nocow_only flag to wait_ordered_extents if snap_pending.
Signed-off-by: Sage Weil <sage@newdream.net>
Signed-off-by: Chris Mason <chris.mason@oracle.com>
btrfs_split_leaf and btrfs_del_items can end up in a loop
where one is constantly spliting a given leaf and the other
is constantly merging it back with the adjacent nodes.
There is a better fix for this, but in the interest of something
small, this patch just changes btrfs_del_items back to balancing less
often.
Signed-off-by: Chris Mason <chris.mason@oracle.com>
Check objectid of item before checking the item type, otherwise we may return
zero for a key that is actually too low.
Signed-off-by: Yan Zheng <zheng.yan@oracle.com>
Signed-off-by: Chris Mason <chris.mason@oracle.com>
find_free_dev_extent does not properly handle the case where
the device is not complete free, and there is a free extent
at the beginning of the device.
Signed-off-by: Yan Zheng <zheng.yan@oracle.com>
Signed-off-by: Chris Mason <chris.mason@oracle.com>
comp_keys is duplicating what is done in btrfs_comp_cpu_keys, so just
call it.
Signed-off-by: Diego Calleja <diegocg@gmail.com>
Signed-off-by: Chris Mason <chris.mason@oracle.com>
This patch moves the caching of the block group off to a kthread in order to
allow people to allocate sooner. Instead of blocking up behind the caching
mutex, we instead kick of the caching kthread, and then attempt to make an
allocation. If we cannot, we wait on the block groups caching waitqueue, which
the caching kthread will wake the waiting threads up everytime it finds 2 meg
worth of space, and then again when its finished caching. This is how I tested
the speedup from this
mkfs the disk
mount the disk
fill the disk up with fs_mark
unmount the disk
mount the disk
time touch /mnt/foo
Without my changes this took 11 seconds on my box, with these changes it now
takes 1 second.
Another change thats been put in place is we lock the super mirror's in the
pinned extent map in order to keep us from adding that stuff as free space when
caching the block group. This doesn't really change anything else as far as the
pinned extent map is concerned, since for actual pinned extents we use
EXTENT_DIRTY, but it does mean that when we unmount we have to go in and unlock
those extents to keep from leaking memory.
I've also added a check where when we are reading block groups from disk, if the
amount of space used == the size of the block group, we go ahead and mark the
block group as cached. This drastically reduces the amount of time it takes to
cache the block groups. Using the same test as above, except doing a dd to a
file and then unmounting, it used to take 33 seconds to umount, now it takes 3
seconds.
This version uses the commit_root in the caching kthread, and then keeps track
of how many async caching threads are running at any given time so if one of the
async threads is still running as we cross transactions we can wait until its
finished before handling the pinned extents. Thank you,
Signed-off-by: Josef Bacik <jbacik@redhat.com>
Signed-off-by: Chris Mason <chris.mason@oracle.com>
Currently btrfs has a problem where it can use a ridiculous amount of RAM simply
tracking free space. As free space gets fragmented, we end up with thousands of
entries on an rb-tree per block group, which usually spans 1 gig of area. Since
we currently don't ever flush free space cache back to disk this gets to be a
bit unweildly on large fs's with lots of fragmentation.
This patch solves this problem by using PAGE_SIZE bitmaps for parts of the free
space cache. Initially we calculate a threshold of extent entries we can
handle, which is however many extent entries we can cram into 16k of ram. The
maximum amount of RAM that should ever be used to track 1 gigabyte of diskspace
will be 32k of RAM, which scales much better than we did before.
Once we pass the extent threshold, we start adding bitmaps and using those
instead for tracking the free space. This patch also makes it so that any free
space thats less than 4 * sectorsize we go ahead and put into a bitmap. This is
nice since we try and allocate out of the front of a block group, so if the
front of a block group is heavily fragmented and then has a huge chunk of free
space at the end, we go ahead and add the fragmented areas to bitmaps and use a
normal extent entry to track the big chunk at the back of the block group.
I've also taken the opportunity to revamp how we search for free space.
Previously we indexed free space via an offset indexed rb tree and a bytes
indexed rb tree. I've dropped the bytes indexed rb tree and use only the offset
indexed rb tree. This cuts the number of tree operations we were doing
previously down by half, and gives us a little bit of a better allocation
pattern since we will always start from a specific offset and search forward
from there, instead of searching for the size we need and try and get it as
close as possible to the offset we want.
I've given this a healthy amount of testing pre-new format stuff, as well as
post-new format stuff. I've booted up my fedora box which is installed on btrfs
with this patch and ran with it for a few days without issues. I've not seen
any performance regressions in any of my tests.
Since the last patch Yan Zheng fixed a problem where we could have overlapping
entries, so updating their offset inline would cause problems. Thanks,
Signed-off-by: Josef Bacik <jbacik@redhat.com>
Signed-off-by: Chris Mason <chris.mason@oracle.com>
If the tree roots hit read errors during mount, btrfs is not properly
erroring out. We need to check the uptodate bits after
reading in the tree root node.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Signed-off-by: Chris Mason <chris.mason@oracle.com>
This removes the continues call's of btrfs_header_level. One call of
btrfs_header_level(c) its enough.
Signed-off-by Daniel Cadete <danielncadete10@gmail.com>
Signed-off-by: Chris Mason <chris.mason@oracle.com>
Move the call to BUG_ON to before the dereference of the tested value.
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Chris Mason <chris.mason@oracle.com>
It was never actually doing anything anyway (see the loop condition),
and it would be difficult to make it work for RAID[56].
Even if it was actually working, it's checking for the wrong thing
anyway. Instead of checking whether we list a block which _doesn't_ land
at the relevant physical location, it should be checking that we _have_
listed all the logical blocks which refer to the required physical
location on all devices.
This function is only called from remove_sb_from_cache() to ensure that
we reserve the logical blocks which would reside at the same physical
location as the superblock copies. So listing more blocks than we need
is actually OK.
With RAID[56] we're going to throw away an entire stripe for each block
we have to ignore, so we _are_ going to list blocks other than the
ones which actually contain the superblock.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Signed-off-by: Chris Mason <chris.mason@oracle.com>
If spin_lock_irqsave is called twice in a row with the same second
argument, the interrupt state at the point of the second call overwrites
the value saved by the first call. Indeed, the second call does not need
to save the interrupt state, so it is changed to a simple spin_lock.
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Chris Mason <chris.mason@oracle.com>
Write dirty block groups may allocate new block, and so may add new delayed
back ref. btrfs_run_delayed_refs may make some block groups dirty.
commit_cowonly_roots does not handle the recursion properly, and some dirty
blocks can be left unwritten at commit time. This patch moves
btrfs_run_delayed_refs into the loop that writes dirty block groups, and makes
the code not break out of the loop until there are no dirty block groups or
delayed back refs.
Signed-off-by: Yan Zheng <zheng.yan@oracle.com>
Signed-off-by: Chris Mason <chris.mason@oracle.com>
When walking up the tree, btrfs_find_next_key assumes the upper level tree
block is properly locked. This isn't always true even path->keep_locks is 1.
This is because btrfs_find_next_key may advance path->slots[] several times
instead of only once.
When 'path->slots[level] >= btrfs_header_nritems(path->nodes[level])' is found,
we can't guarantee the original value of 'path->slots[level]' is
'btrfs_header_nritems(path->nodes[level]) - 1'. If it's not, the tree block at
'level + 1' isn't locked.
This patch fixes the issue by explicitly checking the locking state,
re-searching the tree if it's not locked.
Signed-off-by: Yan Zheng <zheng.yan@oracle.com>
Signed-off-by: Chris Mason <chris.mason@oracle.com>
if 1 is returned by btrfs_search_slot, the path already points to the
first item with 'key > searching key'. So increasing path->slots[0] by
one is superfluous in that case.
Signed-off-by: Yan Zheng <zheng.yan@oracle.com>
Signed-off-by: Chris Mason <chris.mason@oracle.com>
Change 'goto done' to 'break' for the case of all device extents have
been freed, so that the code updates space information will be execute.
Signed-off-by: Yan Zheng <zheng.yan@oracle.com>
Signed-off-by: Chris Mason <chris.mason@oracle.com>
use __le64 instead of u64 in on-disk structure definition.
Signed-off-by: Yan Zheng <zheng.yan@oracle.com>
Signed-off-by: Chris Mason <chris.mason@oracle.com>
* Remove smp_lock.h from files which don't need it (including some headers!)
* Add smp_lock.h to files which do need it
* Make smp_lock.h include conditional in hardirq.h
It's needed only for one kernel_locked() usage which is under CONFIG_PREEMPT
This will make hardirq.h inclusion cheaper for every PREEMPT=n config
(which includes allmodconfig/allyesconfig, BTW)
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/mason/btrfs-unstable:
Btrfs: fix error message formatting
Btrfs: fix use after free in btrfs_start_workers fail path
Btrfs: honor nodatacow/sum mount options for new files
Btrfs: update backrefs while dropping snapshot
Btrfs: account for space we may use in fallocate
Btrfs: fix the file clone ioctl for preallocated extents
Btrfs: don't log the inode in file_write while growing the file
Make an error msg look nicer by inserting a space between number and word.
Signed-off-by: Hu Tao <hu.taoo@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Chris Mason <chris.mason@oracle.com>
worker memory is already freed on one fail path in btrfs_start_workers,
but is still dereferenced. Switch the dereference and kfree.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Chris Mason <chris.mason@oracle.com>
The btrfs attr patches unconditionally inherited the inode flags field
without honoring nodatacow and nodatasum. This fix makes sure
we properly record the nodatacow/sum mount options in new inodes.
Signed-off-by: Chris Mason <chris.mason@oracle.com>
The new backref format has restriction on type of backref item. If a tree
block isn't referenced by its owner tree, full backrefs must be used for the
pointers in it. When a tree block loses its owner tree's reference, backrefs
for the pointers in it should be updated to full backrefs. Current
btrfs_drop_snapshot misses the code that updates backrefs, so it's unsafe for
general use.
This patch adds backrefs update code to btrfs_drop_snapshot. It isn't a
problem in the restricted form btrfs_drop_snapshot is used today, but for
general snapshot deletion this update is required.
Signed-off-by: Yan Zheng <zheng.yan@oracle.com>
Signed-off-by: Chris Mason <chris.mason@oracle.com>
Using Eric Sandeen's xfstest for fallocate, you can easily trigger a ENOSPC
panic on btrfs. This is because we do not account for data we may use when
doing the fallocate. This patch fixes the problem by properly reserving space,
and then just freeing it when we are done. The reservation stuff was made with
delalloc in mind, so its a little crude for this case, but it keeps the box
from panicing.
Signed-off-by: Josef Bacik <jbacik@redhat.com>
Signed-off-by: Chris Mason <chris.mason@oracle.com>
helpers: get_cached_acl(inode, type), set_cached_acl(inode, type, acl),
forget_cached_acl(inode, type).
ubifs/xattr.c needed includes reordered, the rest is a plain switchover.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
* 'for-linus' of git://git.kernel.dk/linux-2.6-block:
block: remove some includings of blktrace_api.h
mg_disk: seperate mg_disk.h again
block: Introduce helper to reset queue limits to default values
cfq: remove extraneous '\n' in blktrace output
ubifs: register backing_dev_info
btrfs: properly register fs backing device
block: don't overwrite bdi->state after bdi_init() has been run
cfq: cleanup for last_end_request in cfq_data
btrfs assigns this bdi to all inodes on that file system, so make
sure it's registered. This isn't really important now, but will be
when we put dirty inodes there. Even now, we miss the stats when the
bdi isn't visible.
Also fixes failure to check bdi_init() return value, and bad inherit of
->capabilities flags from the default bdi.
Acked-by: Chris Mason <chris.mason@oracle.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
commit_fs_roots skips updating root items for fs trees that aren't modified.
This is unsafe now that relocation code modifies root item's last_snapshot
field without modifying corresponding fs tree.
Signed-off-by: Yan Zheng <zheng.yan@oracle.com>
Signed-off-by: Chris Mason <chris.mason@oracle.com>
Make sure a superblock really is writeable by checking MS_RDONLY
under s_umount. sync_filesystems needed some re-arragement for
that, but all but one sync_filesystem caller had the correct locking
already so that we could add that check there. cachefiles grew
s_umount locking.
I've also added a WARN_ON to sync_filesystem to assert this for
future callers.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
During tree log replay, we read in the tree log roots,
process them and then free them. A recent change
takes an extra reference on the root node of the tree
when the root is read in, and stores that reference
in root->commit_root.
This reference was not being freed, leaving us with
one buffer pinned in ram for each subvol with
a tree log root after a crash.
Signed-off-by: Chris Mason <chris.mason@oracle.com>
lookup_inline_extent_backref only checks for duplicate backref for data
extents. It assumes backrefs for tree block never conflict.
This patch makes lookup_inline_extent_backref check for duplicate backrefs
for both data and tree block, so that we can detect potential bug earlier.
This is a safety check, strictly speaking it is not required.
Signed-off-by: Yan Zheng <zheng.yan@oracle.com>
Signed-off-by: Chris Mason <chris.mason@oracle.com>
This patch fixes a bug which may result race condition
between btrfs_start_workers() and worker_loop().
btrfs_start_workers() executed in a parent thread writes
on workers->worker and worker_loop() in a child thread
reads workers->worker. However, there is no synchronization
enforcing the order of two operations.
This patch makes btrfs_start_workers() fill workers->worker
before it starts a child thread with worker_loop()
Signed-off-by: Chris Mason <chris.mason@oracle.com>
write_dev_supers is called in sequence. First is it called with wait == 0,
which starts IO on all of the super blocks for a given device. Then it is
called with wait == 1 to make sure they all reach the disk.
It doesn't currently pin the buffers between the two calls, and it also
assumes the buffers won't go away between the two calls, leading to
an oops if the VM manages to free the buffers in the middle of the sync.
This fixes that assumption and updates the code to return an error if things
are not up to date when the wait == 1 run is done.
Signed-off-by: Hisashi Hifumi <hifumi.hisashi@oss.ntt.co.jp>
Signed-off-by: Chris Mason <chris.mason@oracle.com>
On multi-device filesystems, btrfs writes supers to all of the devices
before considering a sync complete. There wasn't any additional
locking between super writeout and the device list management code
because device management was done inside a transaction and
super writeout only happened with no transation writers running.
With the btrfs fsync log and other async transaction updates, this
has been racey for some time. This adds a mutex to protect
the device list. The existing volume mutex could not be reused due to
transaction lock ordering requirements.
Signed-off-by: Chris Mason <chris.mason@oracle.com>
... otherwise generic_permission() will allow *anything* for all
files you don't own and that have some group permissions.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Chris Mason <chris.mason@oracle.com>
In btrfs, fdatasync and fsync are identical, but
fdatasync should skip committing transaction when
inode->i_state is set just I_DIRTY_SYNC and this indicates
only atime or/and mtime updates.
Following patch improves fdatasync throughput.
--file-block-size=4K --file-total-size=16G --file-test-mode=rndwr
--file-fsync-mode=fdatasync run
Results:
-2.6.30-rc8
Test execution summary:
total time: 1980.6540s
total number of events: 10001
total time taken by event execution: 1192.9804
per-request statistics:
min: 0.0000s
avg: 0.1193s
max: 15.3720s
approx. 95 percentile: 0.7257s
Threads fairness:
events (avg/stddev): 625.0625/151.32
execution time (avg/stddev): 74.5613/9.46
-2.6.30-rc8-patched
Test execution summary:
total time: 1695.9118s
total number of events: 10000
total time taken by event execution: 871.3214
per-request statistics:
min: 0.0000s
avg: 0.0871s
max: 10.4644s
approx. 95 percentile: 0.4787s
Threads fairness:
events (avg/stddev): 625.0000/131.86
execution time (avg/stddev): 54.4576/8.98
Signed-off-by: Hisashi Hifumi <hifumi.hisashi@oss.ntt.co.jp>
Signed-off-by: Chris Mason <chris.mason@oracle.com>
There's no need to preserve this abstraction; it used to let us use
hardware crc32c support directly, but libcrc32c is already doing that for us
through the crypto API -- so we're already using the Intel crc32c
acceleration where appropriate.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Signed-off-by: Chris Mason <chris.mason@oracle.com>
Add support for the standard attributes set via chattr and read via
lsattr. Currently we store the attributes in the flags value in
the btrfs inode, but I wonder whether we should split it into two so
that we don't have to keep converting between the two formats.
Remove the btrfs_clear_flag/btrfs_set_flag/btrfs_test_flag macros
as they were confusing the existing code and got in the way of the
new additions.
Also add the FS_IOC_GETVERSION ioctl for getting i_generation as it's
trivial.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Chris Mason <chris.mason@oracle.com>
During mount, btrfs will check the queue nonrot flag
for all the devices found in the FS. If they are all
non-rotating, SSD mode is enabled by default.
If the FS was mounted with -o nossd, the non-rotating
flag is ignored.
Signed-off-by: Chris Mason <chris.mason@oracle.com>
Some SSDs perform best when reusing block numbers often, while
others perform much better when clustering strictly allocates
big chunks of unused space.
The default mount -o ssd will find rough groupings of blocks
where there are a bunch of free blocks that might have some
allocated blocks mixed in.
mount -o ssd_spread will make sure there are no allocated blocks
mixed in. It should perform better on lower end SSDs.
Signed-off-by: Chris Mason <chris.mason@oracle.com>
In SSD mode for data, and all the time for metadata the allocator
will try to find a cluster of nearby blocks for allocations. This
commit adds extra checks to make sure that each free block in the
cluster is close to the last one.
Signed-off-by: Chris Mason <chris.mason@oracle.com>
The btrfs IO submission threads try to service a bunch of devices with a small
number of threads. They do a congestion check to try and avoid waiting
on requests for a busy device.
The checks make sure we've sent a few requests down to a given device just so
that we aren't bouncing between busy devices without actually sending down
any IO. The counter used to decide if we can switch to the next device
is somewhat overloaded. It is also being used to decide if we've done
a good batch of requests between the WRITE_SYNC or regular priority lists.
It may get reset to zero often, leaving us hammering on a busy device
instead of moving on to another disk.
This commit adds a new counter for the number of bios sent while
servicing a device. It doesn't get reset or fiddled with. On
multi-device filesystems, this fixes IO stalls in streaming
write workloads.
Signed-off-by: Chris Mason <chris.mason@oracle.com>
Btrfs uses dedicated threads to submit bios when checksumming is on,
which allows us to make sure the threads dedicated to checksumming don't get
stuck waiting for requests. For each btrfs device, there are
two lists of bios. One list is for WRITE_SYNC bios and the other
is for regular priority bios.
The IO submission threads used to process all of the WRITE_SYNC bios first and
then switch to the regular bios. This commit makes sure we don't completely
starve the regular bios by rotating between the two lists.
WRITE_SYNC bios are still favored 2:1 over the regular bios, and this tries
to run in batches to avoid seeking. Benchmarking shows this eliminates
stalls during streaming buffered writes on both multi-device and
single device filesystems.
If the regular bios starve, the system can end up with a large amount of ram
pinned down in writeback pages. If we are a little more fair between the two
classes, we're able to keep throughput up and make progress on the bulk of
our dirty ram.
Signed-off-by: Chris Mason <chris.mason@oracle.com>
Once a metadata block has been written, it must be recowed, so the
btrfs dirty balancing call has a check to make sure a fair amount of metadata
was actually dirty before it started writing it back to disk.
A previous commit had changed the dirty tracking for metadata without
updating the btrfs dirty balancing checks. This commit switches it
to use the correct counter.
Signed-off-by: Chris Mason <chris.mason@oracle.com>
The block allocator in SSD mode will try to find groups of free blocks
that are close together. This commit makes it loop less on a given
group size before bumping it.
The end result is that we are less likely to fill small holes in the
available free space, but we don't waste as much CPU building the
large cluster used by ssd mode.
Signed-off-by: Chris Mason <chris.mason@oracle.com>
With the new back reference code, the cost of a balance has gone down
in terms of the number of back reference updates done. This commit
makes us more aggressively balance leaves and nodes as they become
less full.
Signed-off-by: Chris Mason <chris.mason@oracle.com>
When the delayed reference code was added, some checks were added
to avoid extra balancing while the delayed references were being flushed.
This made for less efficient btrees, but it reduced the chances of
loops where no forward progress was made because the balances made
more delayed ref updates.
With the new dead root removal code and the mixed back references,
the extent allocation tree is no longer using precise back refs, and
the delayed reference updates don't carry the risk of looping forever
anymore. So, the balance avoidance is no longer required.
Signed-off-by: Chris Mason <chris.mason@oracle.com>
This commit introduces a new kind of back reference for btrfs metadata.
Once a filesystem has been mounted with this commit, IT WILL NO LONGER
BE MOUNTABLE BY OLDER KERNELS.
When a tree block in subvolume tree is cow'd, the reference counts of all
extents it points to are increased by one. At transaction commit time,
the old root of the subvolume is recorded in a "dead root" data structure,
and the btree it points to is later walked, dropping reference counts
and freeing any blocks where the reference count goes to 0.
The increments done during cow and decrements done after commit cancel out,
and the walk is a very expensive way to go about freeing the blocks that
are no longer referenced by the new btree root. This commit reduces the
transaction overhead by avoiding the need for dead root records.
When a non-shared tree block is cow'd, we free the old block at once, and the
new block inherits old block's references. When a tree block with reference
count > 1 is cow'd, we increase the reference counts of all extents
the new block points to by one, and decrease the old block's reference count by
one.
This dead tree avoidance code removes the need to modify the reference
counts of lower level extents when a non-shared tree block is cow'd.
But we still need to update back ref for all pointers in the block.
This is because the location of the block is recorded in the back ref
item.
We can solve this by introducing a new type of back ref. The new
back ref provides information about pointer's key, level and in which
tree the pointer lives. This information allow us to find the pointer
by searching the tree. The shortcoming of the new back ref is that it
only works for pointers in tree blocks referenced by their owner trees.
This is mostly a problem for snapshots, where resolving one of these
fuzzy back references would be O(number_of_snapshots) and quite slow.
The solution used here is to use the fuzzy back references in the common
case where a given tree block is only referenced by one root,
and use the full back references when multiple roots have a reference
on a given block.
This commit adds per subvolume red-black tree to keep trace of cached
inodes. The red-black tree helps the balancing code to find cached
inodes whose inode numbers within a given range.
This commit improves the balancing code by introducing several data
structures to keep the state of balancing. The most important one
is the back ref cache. It caches how the upper level tree blocks are
referenced. This greatly reduce the overhead of checking back ref.
The improved balancing code scales significantly better with a large
number of snapshots.
This is a very large commit and was written in a number of
pieces. But, they depend heavily on the disk format change and were
squashed together to make sure git bisect didn't end up in a
bad state wrt space balancing or the format change.
Signed-off-by: Yan Zheng <zheng.yan@oracle.com>
Signed-off-by: Chris Mason <chris.mason@oracle.com>
There are some 'start = state->end + 1;' like code in set_extent_bit
and clear_extent_bit. They overflow when end == (u64)-1.
Signed-off-by: Yan Zheng <zheng.yan@oracle.com>
Signed-off-by: Chris Mason <chris.mason@oracle.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/mason/btrfs-unstable:
Btrfs: Fix oops and use after free during space balancing
Btrfs: set device->total_disk_bytes when adding new device
The btrfs allocator uses list_for_each to walk the available block
groups when searching for free blocks. It starts off with a hint
to help find the best block group for a given allocation.
The hint is resolved into a block group, but we don't properly check
to make sure the block group we find isn't in the middle of being
freed due to filesystem shrinking or balancing. If it is being
freed, the list pointers in it are bogus and can't be trusted. But,
the code happily goes along and uses them in the list_for_each loop,
leading to all kinds of fun.
The fix used here is to check to make sure the block group we find really
is on the list before we use it. list_del_init is used when removing
it from the list, so we can do a proper check.
The allocation clustering code has a similar bug where it will trust
the block group in the current free space cluster. If our allocation
flags have changed (going from single spindle dup to raid1 for example)
because the drives in the FS have changed, we're not allowed to use
the old block group any more.
The fix used here is to check the current cluster against the
current allocation flags.
Signed-off-by: Chris Mason <chris.mason@oracle.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/mason/btrfs-unstable:
Btrfs: Spelling fix in btrfs_lookup_first_block_group comments
Btrfs: make show_options result match actual option names
Btrfs: remove outdated comment in btrfs_ioctl_resize()
Btrfs: remove some WARN_ONs in the IO failure path
Btrfs: Don't loop forever on metadata IO failures
Btrfs: init inode ordered_data_close flag properly
The notreelog and flushoncommit mount options were being printed slightly
differently.
Signed-off-by: Sage Weil <sage@newdream.net>
Signed-off-by: Chris Mason <chris.mason@oracle.com>
In Li Zefan's commit dae7b665cf,
a combination call of kmalloc() and copy_from_user() is replaced by
memdup_user(). So btrfs_ioctl_resize() doesn't use GFP_NOFS any more.
Signed-off-by: Li Hong <lihong.hi@gmail.com>
Signed-off-by: Chris Mason <chris.mason@oracle.com>
These debugging WARN_ONs make too much console noise during regular
IO failures. An IO failure will still generate a number of messages
as we verify checksums etc, but these two are not needed.
Signed-off-by: Chris Mason <chris.mason@oracle.com>
When a btrfs metadata read fails, the first thing we try to do is find
a good copy on another mirror of the block. If this fails, read_tree_block()
ends up returning a buffer that isn't up to date.
The btrfs btree reading code was reworked to drop locks and repeat
the search when IO was done, but the changes didn't add a check for failed
reads. The end result was looping forever on buffers that were never
going to become up to date.
Signed-off-by: Chris Mason <chris.mason@oracle.com>
This flag is used to decide when we need to send a given file through
the ordered code to make sure it is fully written before a transaction
commits. It was not being properly set to zero when the inode was
being setup.
Signed-off-by: Chris Mason <chris.mason@oracle.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/mason/btrfs-unstable:
Btrfs: look for acls during btrfs_read_locked_inode
Btrfs: fix acl caching
Btrfs: Fix a bunch of printk() warnings.
Btrfs: Fix a trivial warning using max() of u64 vs ULL.
Btrfs: remove unused btrfs_bit_radix slab
Btrfs: ratelimit IO error printks
Btrfs: remove #if 0 code
Btrfs: When shrinking, only update disk size on success
Btrfs: fix deadlocks and stalls on dead root removal
Btrfs: fix fallocate deadlock on inode extent lock
Btrfs: kill btrfs_cache_create
Btrfs: don't export symbols
Btrfs: simplify makefile
Btrfs: try to keep a healthy ratio of metadata vs data block groups
This changes btrfs_read_locked_inode() to peek ahead in the btree for acl items.
If it is certain a given inode has no acls, it will set the in memory acl
fields to null to avoid acl lookups completely.
Signed-off-by: Chris Mason <chris.mason@oracle.com>
Linus noticed the btrfs code to cache acls wasn't properly caching
a NULL acl when the inode didn't have any acls. This meant the common
case of no acls resulted in expensive btree searches every time the
kernel checked permissions (which is quite often).
This is a modified version of Linus' original patch:
Properly set initial acl fields to BTRFS_ACL_NOT_CACHED in the inode.
This forces an acl lookup when permission checks are done.
Fix btrfs_get_acl to avoid lookups and locking when the inode acls fields
are set to null.
Fix btrfs_get_acl to use the right return value from __btrfs_getxattr
when deciding to cache a NULL acl. It was storing a NULL acl when
__btrfs_getxattr return -ENOENT, but __btrfs_getxattr was actually returning
-ENODATA for this case.
Signed-off-by: Chris Mason <chris.mason@oracle.com>
Just happened to notice a bunch of %llu vs u64 warnings. Here's a patch
to cast them all.
Signed-off-by: Joel Becker <joel.becker@oracle.com>
Signed-off-by: Chris Mason <chris.mason@oracle.com>
A small warning popped up on ia64 because inode-map.c was comparing a
u64 object id with the ULL FIRST_FREE_OBJECTID. My first thought was
that all the OBJECTID constants should contain the u64 cast because
btrfs code deals entirely in u64s. But then I saw how large that was,
and figured I'd just fix the max() call.
Signed-off-by: Joel Becker <joel.becker@oracle.com>
Signed-off-by: Chris Mason <chris.mason@oracle.com>
Btrfs has printks for various IO errors, including bad checksums and
mismatches between what we expect the block headers to contain and what
we actually find on the disk.
Longer term we need a real reporting mechanism for this, but for now
printk is going to have to do.
Signed-off-by: Chris Mason <chris.mason@oracle.com>
Previously, we updated a device's size prior to attempting a shrink
operation. This patch moves the device resizing logic to only happen if
the shrink completes successfully. In the process, it introduces a new
field to btrfs_device -- disk_total_bytes -- to track the on-disk size.
Signed-off-by: Chris Ball <cjb@laptop.org>
Signed-off-by: Chris Mason <chris.mason@oracle.com>
After a transaction commit, the old root of the subvol btrees are sent through
snapshot removal. This is what actually frees up any blocks replaced by
COW, and anything the old blocks pointed to.
Snapshot deletion will pause when a transaction commit has started, which
helps to avoid a huge amount of delayed reference count updates piling up
as the transaction is trying to close.
But, this pause happens after the snapshot deletion process has asked other
procs on the system to throttle back a bit so that it can make progress.
We don't want to throttle everyone while we're waiting for the transaction
commit, it leads to deadlocks in the user transaction ioctls used by Ceph
and makes things slower in general.
This patch changes things to avoid the throttling while we sleep.
Signed-off-by: Chris Mason <chris.mason@oracle.com>
The btrfs fallocate call takes an extent lock on the entire range
being fallocated, and then runs through insert_reserved_extent on each
extent as they are allocated.
The problem with this is that btrfs_drop_extents may decide to try
and take the same extent lock fallocate was already holding. The solution
used here is to push down knowledge of the range that is already locked
going into btrfs_drop_extents.
It turns out that at least one other caller had the same bug.
Signed-off-by: Chris Mason <chris.mason@oracle.com>
Currently the extent_map code is only for btrfs so don't export it's
symbols.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Chris Mason <chris.mason@oracle.com>
Get rid of the hacks for building out of tree, and always use += for
assigning to the object lists.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Chris Mason <chris.mason@oracle.com>
This patch makes the chunk allocator keep a good ratio of metadata vs data
block groups. By default for every 8 data block groups, we'll allocate 1
metadata chunk, or about 12% of the disk will be allocated for metadata. This
can be changed by specifying the metadata_ratio mount option.
This is simply the number of data block groups that have to be allocated to
force a metadata chunk allocation. By making sure we allocate metadata chunks
more often, we are less likely to get into situations where the whole disk
has been allocated as data block groups.
Signed-off-by: Josef Bacik <jbacik@redhat.com>
Signed-off-by: Chris Mason <chris.mason@oracle.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/mason/btrfs-unstable:
Btrfs: fix btrfs fallocate oops and deadlock
Btrfs: use the right node in reada_for_balance
Btrfs: fix oops on page->mapping->host during writepage
Btrfs: add a priority queue to the async thread helpers
Btrfs: use WRITE_SYNC for synchronous writes
Btrfs fallocate was incorrectly starting a transaction with a lock held
on the extent_io tree for the file, which could deadlock. Strictly
speaking it was using join_transaction which would be safe, but it is better
to move the transaction outside of the lock.
When preallocated extents are overwritten, btrfs_mark_buffer_dirty was
being called on an unlocked buffer. This was triggering an assertion and
oops because the lock is supposed to be held.
The bug was calling btrfs_mark_buffer_dirty on a leaf after btrfs_del_item had
been run. btrfs_del_item takes care of dirtying things, so the solution is a
to skip the btrfs_mark_buffer_dirty call in this case.
Signed-off-by: Chris Mason <chris.mason@oracle.com>
Remove open-coded memdup_user().
Note this changes some GFP_NOFS to GFP_KERNEL, since copy_from_user() may
cause pagefault, it's pointless to pass GFP_NOFS to kmalloc().
Signed-off-by: Li Zefan <lizf@cn.fujitsu.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
reada_for_balance was using the wrong index into the path node array,
so it wasn't reading the right blocks. We never directly used the
results of the read done by this function because the btree search is
started over at the end.
This fixes reada_for_balance to reada in the correct node and to
avoid searching past the last slot in the node. It also makes sure to
hold the parent lock while we are finding the nodes to read.
Signed-off-by: Chris Mason <chris.mason@oracle.com>
The extent_io writepage call updates the writepage index in the inode
as it makes progress. But, it was doing the update after unlocking the page,
which isn't legal because page->mapping can't be trusted once the page
is unlocked.
This lead to an oops, especially common with compression turned on. The
fix here is to update the writeback index before unlocking the page.
Signed-off-by: Chris Mason <chris.mason@oracle.com>
Btrfs is using WRITE_SYNC_PLUG to send down synchronous IOs with a
higher priority. But, the checksumming helper threads prevent it
from being fully effective.
There are two problems. First, a big queue of pending checksumming
will delay the synchronous IO behind other lower priority writes. Second,
the checksumming uses an ordered async work queue. The ordering makes sure
that IOs are sent to the block layer in the same order they are sent
to the checksumming threads. Usually this gives us less seeky IO.
But, when we start mixing IO priorities, the lower priority IO can delay
the higher priority IO.
This patch solves both problems by adding a high priority list to the async
helper threads, and a new btrfs_set_work_high_prio(), which is used
to make put a new async work item onto the higher priority list.
The ordering is still done on high priority IO, but all of the high
priority bios are ordered separately from the low priority bios. This
ordering is purely an IO optimization, it is not involved in data
or metadata integrity.
Signed-off-by: Chris Mason <chris.mason@oracle.com>
Part of reducing fsync/O_SYNC/O_DIRECT latencies is using WRITE_SYNC for
writes we plan on waiting on in the near future. This patch
mirrors recent changes in other filesystems and the generic code to
use WRITE_SYNC when WB_SYNC_ALL is passed and to use WRITE_SYNC for
other latency critical writes.
Btrfs uses async worker threads for checksumming before the write is done,
and then again to actually submit the bios. The bio submission code just
runs a per-device list of bios that need to be sent down the pipe.
This list is split into low priority and high priority lists so the
WRITE_SYNC IO happens first.
Signed-off-by: Chris Mason <chris.mason@oracle.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/mason/btrfs-unstable:
Btrfs: BUG to BUG_ON changes
Btrfs: remove dead code
Btrfs: remove dead code
Btrfs: fix typos in comments
Btrfs: remove unused ftrace include
Btrfs: fix __ucmpdi2 compile bug on 32 bit builds
Btrfs: free inode struct when btrfs_new_inode fails
Btrfs: fix race in worker_loop
Btrfs: add flushoncommit mount option
Btrfs: notreelog mount option
Btrfs: introduce btrfs_show_options
Btrfs: rework allocation clustering
Btrfs: Optimize locking in btrfs_next_leaf()
Btrfs: break up btrfs_search_slot into smaller pieces
Btrfs: kill the pinned_mutex
Btrfs: kill the block group alloc mutex
Btrfs: clean up find_free_extent
Btrfs: free space cache cleanups
Btrfs: unplug in the async bio submission threads
Btrfs: keep processing bios for a given bdev if our proc is batching
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs-2.6:
Remove two unneeded exports and make two symbols static in fs/mpage.c
Cleanup after commit 585d3bc06f
Trim includes of fdtable.h
Don't crap into descriptor table in binfmt_som
Trim includes in binfmt_elf
Don't mess with descriptor table in load_elf_binary()
Get rid of indirect include of fs_struct.h
New helper - current_umask()
check_unsafe_exec() doesn't care about signal handlers sharing
New locking/refcounting for fs_struct
Take fs_struct handling to new file (fs/fs_struct.c)
Get rid of bumping fs_struct refcount in pivot_root(2)
Kill unsharing fs_struct in __set_personality()
Remove an unneeded return statement and conditional
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Chris Mason <chris.mason@oracle.com>
We get this on 32 builds:
fs/built-in.o: In function `extent_fiemap':
(.text+0x1019f2): undefined reference to `__ucmpdi2'
Happens because of a switch statement with a 64 bit argument.
Convert this to an if statement to fix this.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Chris Mason <chris.mason@oracle.com>
btrfs_new_inode doesn't call iput to free the inode
when it fails.
Signed-off-by: Shen Feng <shen@cn.fujitsu.com>
Signed-off-by: Chris Mason <chris.mason@oracle.com>
Need to check kthread_should_stop after schedule_timeout() before calling
schedule(). This causes threads to sleep with potentially no one to wake them
up causing mount(2) to hang in btrfs_stop_workers waiting for threads to stop.
Signed-off-by: Amit Gud <gud@ksu.edu>
Signed-off-by: Chris Mason <chris.mason@oracle.com>
The 'flushoncommit' mount option forces any data dirtied by a write in a
prior transaction to commit as part of the current commit. This makes
the committed state a fully consistent view of the file system from the
application's perspective (i.e., it includes all completed file system
operations). This was previously the behavior only when a snapshot is
created.
This is used by Ceph to ensure that completed writes make it to the
platter along with the metadata operations they are bound to (by
BTRFS_IOC_TRANS_{START,END}).
Signed-off-by: Sage Weil <sage@newdream.net>
Signed-off-by: Chris Mason <chris.mason@oracle.com>
Add a 'notreelog' mount option to disable the tree log (used by fsync,
O_SYNC writes). This is much slower, but the tree logging produces
inconsistent views into the FS for ceph.
Signed-off-by: Sage Weil <sage@newdream.net>
Signed-off-by: Chris Mason <chris.mason@oracle.com>
btrfs options can change at times other than mount, yet /proc/mounts shows the
options string used when the fs was mounted (an example would be when btrfs
determines that barriers aren't useful and turns them off.) This patch
instead outputs the actual options in use by btrfs.
Signed-off-by: Eric Paris <eparis@redhat.com>
Signed-off-by: Chris Mason <chris.mason@oracle.com>
Because btrfs is copy-on-write, we end up picking new locations for
blocks very often. This makes it fairly difficult to maintain perfect
read patterns over time, but we can at least do some optimizations
for writes.
This is done today by remembering the last place we allocated and
trying to find a free space hole big enough to hold more than just one
allocation. The end result is that we tend to write sequentially to
the drive.
This happens all the time for metadata and it happens for data
when mounted -o ssd. But, the way we record it is fairly racey
and it tends to fragment the free space over time because we are trying
to allocate fairly large areas at once.
This commit gets rid of the races by adding a free space cluster object
with dedicated locking to make sure that only one process at a time
is out replacing the cluster.
The free space fragmentation is somewhat solved by allowing a cluster
to be comprised of smaller free space extents. This part definitely
adds some CPU time to the cluster allocations, but it allows the allocator
to consume the small holes left behind by cow.
Signed-off-by: Chris Mason <chris.mason@oracle.com>
btrfs_next_leaf was using blocking locks when it could have been using
faster spinning ones instead. This adds a few extra checks around
the pieces that block and switches over to spinning locks.
Signed-off-by: Chris Mason <chris.mason@oracle.com>
This patch removes the pinned_mutex. The extent io map has an internal tree
lock that protects the tree itself, and since we only copy the extent io map
when we are committing the transaction we don't need it there. We also don't
need it when caching the block group since searching through the tree is also
protected by the internal map spin lock.
Signed-off-by: Josef Bacik <jbacik@redhat.com>
This patch removes the block group alloc mutex used to protect the free space
tree for allocations and replaces it with a spin lock which is used only to
protect the free space rb tree. This means we only take the lock when we are
directly manipulating the tree, which makes us a touch faster with
multi-threaded workloads.
This patch also gets rid of btrfs_find_free_space and replaces it with
btrfs_find_space_for_alloc, which takes the number of bytes you want to
allocate, and empty_size, which is used to indicate how much free space should
be at the end of the allocation.
It will return an offset for the allocator to use. If we don't end up using it
we _must_ call btrfs_add_free_space to put it back. This is the tradeoff to
kill the alloc_mutex, since we need to make sure nobody else comes along and
takes our space.
Signed-off-by: Josef Bacik <jbacik@redhat.com>
I've replaced the strange looping constructs with a list_for_each_entry on
space_info->block_groups. If we have a hint we just jump into the loop with
the block group and start looking for space. If we don't find anything we
start at the beginning and start looking. We never come out of the loop with a
ref on the block_group _unless_ we found space to use, then we drop it after we
set the trans block_group.
Signed-off-by: Josef Bacik <jbacik@redhat.com>
This patch cleans up the free space cache code a bit. It better documents the
idiosyncrasies of tree_search_offset and makes the code make a bit more sense.
I took out the info allocation at the start of __btrfs_add_free_space and put it
where it makes more sense. This was left over cruft from when alloc_mutex
existed. Also all of the re-searches we do to make sure we inserted properly.
Signed-off-by: Josef Bacik <jbacik@redhat.com>
Btrfs pages being written get set to writeback, and then may go through
a number of steps before they hit the block layer. This includes compression,
checksumming and async bio submission.
The end result is that someone who writes a page and then does
wait_on_page_writeback is likely to unplug the queue before the bio they
cared about got there.
We could fix this by marking bios sync, or by doing more frequent unplugs,
but this commit just changes the async bio submission code to unplug
after it has processed all the bios for a device. The async bio submission
does a fair job of collection bios, so this shouldn't be a huge problem
for reducing merging at the elevator.
For streaming O_DIRECT writes on a 5 drive array, it boosts performance
from 386MB/s to 460MB/s.
Thanks to Hisashi Hifumi for helping with this work.
Signed-off-by: Chris Mason <chris.mason@oracle.com>
Btrfs uses async helper threads to submit write bios so the checksumming
helper threads don't block on the disk.
The submit bio threads may process bios for more than one block device,
so when they find one device congested they try to move on to other
devices instead of blocking in get_request_wait for one device.
This does a pretty good job of keeping multiple devices busy, but the
congested flag has a number of problems. A congested device may still
give you a request, and other procs that aren't backing off the congested
device may starve you out.
This commit uses the io_context stored in current to decide if our process
has been made a batching process by the block layer. If so, it keeps
sending IO down for at least one batch. This helps make sure we do
a good amount of work each time we visit a bdev, and avoids large IO
stalls in multi-device workloads.
It's also very ugly. A better solution is in the works with Jens Axboe.
Signed-off-by: Chris Mason <chris.mason@oracle.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/mason/btrfs-unstable:
Btrfs: try to free metadata pages when we free btree blocks
Btrfs: add extra flushing for renames and truncates
Btrfs: make sure btrfs_update_delayed_ref doesn't increase ref_mod
Btrfs: optimize fsyncs on old files
Btrfs: tree logging unlink/rename fixes
Btrfs: Make sure i_nlink doesn't hit zero too soon during log replay
Btrfs: limit balancing work while flushing delayed refs
Btrfs: readahead checksums during btrfs_finish_ordered_io
Btrfs: leave btree locks spinning more often
Btrfs: Only let very young transactions grow during commit
Btrfs: Check for a blocking lock before taking the spin
Btrfs: reduce stack in cow_file_range
Btrfs: reduce stalls during transaction commit
Btrfs: process the delayed reference queue in clusters
Btrfs: try to cleanup delayed refs while freeing extents
Btrfs: reduce stack usage in some crucial tree balancing functions
Btrfs: do extent allocation and reference count updates in the background
Btrfs: don't preallocate metadata blocks during btrfs_search_slot
page_mkwrite is called with neither the page lock nor the ptl held. This
means a page can be concurrently truncated or invalidated out from
underneath it. Callers are supposed to prevent truncate races themselves,
however previously the only thing they can do in case they hit one is to
raise a SIGBUS. A sigbus is wrong for the case that the page has been
invalidated or truncated within i_size (eg. hole punched). Callers may
also have to perform memory allocations in this path, where again, SIGBUS
would be wrong.
The previous patch ("mm: page_mkwrite change prototype to match fault")
made it possible to properly specify errors. Convert the generic buffer.c
code and btrfs to return sane error values (in the case of page removed
from pagecache, VM_FAULT_NOPAGE will cause the fault handler to exit
without doing anything, and the fault will be retried properly).
This fixes core code, and converts btrfs as a template/example. All other
filesystems defining their own page_mkwrite should be fixed in a similar
manner.
Acked-by: Chris Mason <chris.mason@oracle.com>
Signed-off-by: Nick Piggin <npiggin@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Change the page_mkwrite prototype to take a struct vm_fault, and return
VM_FAULT_xxx flags. There should be no functional change.
This makes it possible to return much more detailed error information to
the VM (and also can provide more information eg. virtual_address to the
driver, which might be important in some special cases).
This is required for a subsequent fix. And will also make it easier to
merge page_mkwrite() with fault() in future.
Signed-off-by: Nick Piggin <npiggin@suse.de>
Cc: Chris Mason <chris.mason@oracle.com>
Cc: Trond Myklebust <trond.myklebust@fys.uio.no>
Cc: Miklos Szeredi <miklos@szeredi.hu>
Cc: Steven Whitehouse <swhiteho@redhat.com>
Cc: Mark Fasheh <mfasheh@suse.com>
Cc: Joel Becker <joel.becker@oracle.com>
Cc: Artem Bityutskiy <dedekind@infradead.org>
Cc: Felix Blyakher <felixb@sgi.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
COW means we cycle though blocks fairly quickly, and once we
free an extent on disk, it doesn't make much sense to keep the pages around.
This commit tries to immediately free the page when we free the extent,
which lowers our memory footprint significantly.
Signed-off-by: Chris Mason <chris.mason@oracle.com>
Renames and truncates are both common ways to replace old data with new
data. The filesystem can make an effort to make sure the new data is
on disk before actually replacing the old data.
This is especially important for rename, which many application use as
though it were atomic for both the data and the metadata involved. The
current btrfs code will happily replace a file that is fully on disk
with one that was just created and still has pending IO.
If we crash after transaction commit but before the IO is done, we'll end
up replacing a good file with a zero length file. The solution used
here is to create a list of inodes that need special ordering and force
them to disk before the commit is done. This is similar to the
ext3 style data=ordering, except it is only done on selected files.
Btrfs is able to get away with this because it does not wait on commits
very often, even for fsync (which use a sub-commit).
For renames, we order the file when it wasn't already
on disk and when it is replacing an existing file. Larger files
are sent to filemap_flush right away (before the transaction handle is
opened).
For truncates, we order if the file goes from non-zero size down to
zero size. This is a little different, because at the time of the
truncate the file has no dirty bytes to order. But, we flag the inode
so that it is added to the ordered list on close (via release method). We
also immediately add it to the ordered list of the current transaction
so that we can try to flush down any writes the application sneaks in
before commit.
Signed-off-by: Chris Mason <chris.mason@oracle.com>
btrfs_update_delayed_ref is optimized to add and remove different
references in one pass through the delayed ref tree. It is a zero
sum on the total number of refs on a given extent.
But, the code was recording an extra ref in the head node. This
never made it down to the disk but was used when deciding if it was
safe to free the extent while dropping snapshots.
The fix used here is to make sure the ref_mod count is unchanged
on the head ref when btrfs_update_delayed_ref is called.
Signed-off-by: Chris Mason <chris.mason@oracle.com>
The fsync log has code to make sure all of the parents of a file are in the
log along with the file. It uses a minimal log of the parent directory
inodes, just enough to get the parent directory on disk.
If the transaction that originally created a file is fully on disk,
and the file hasn't been renamed or linked into other directories, we
can safely skip the parent directory walk. We know the file is on disk
somewhere and we can go ahead and just log that single file.
This is more important now because unrelated unlinks in the parent directory
might make us force a commit if we try to log the parent.
Signed-off-by: Chris Mason <chris.mason@oracle.com>
The tree logging code allows individual files or directories to be logged
without including operations on other files and directories in the FS.
It tries to commit the minimal set of changes to disk in order to
fsync the single file or directory that was sent to fsync or O_SYNC.
The tree logging code was allowing files and directories to be unlinked
if they were part of a rename operation where only one directory
in the rename was in the fsync log. This patch adds a few new rules
to the tree logging.
1) on rename or unlink, if the inode being unlinked isn't in the fsync
log, we must force a full commit before doing an fsync of the directory
where the unlink was done. The commit isn't done during the unlink,
but it is forced the next time we try to log the parent directory.
Solution: record transid of last unlink/rename per directory when the
directory wasn't already logged. For renames this is only done when
renaming to a different directory.
mkdir foo/some_dir
normal commit
rename foo/some_dir foo2/some_dir
mkdir foo/some_dir
fsync foo/some_dir/some_file
The fsync above will unlink the original some_dir without recording
it in its new location (foo2). After a crash, some_dir will be gone
unless the fsync of some_file forces a full commit
2) we must log any new names for any file or dir that is in the fsync
log. This way we make sure not to lose files that are unlinked during
the same transaction.
2a) we must log any new names for any file or dir during rename
when the directory they are being removed from was logged.
2a is actually the more important variant. Without the extra logging
a crash might unlink the old name without recreating the new one
3) after a crash, we must go through any directories with a link count
of zero and redo the rm -rf
mkdir f1/foo
normal commit
rm -rf f1/foo
fsync(f1)
The directory f1 was fully removed from the FS, but fsync was never
called on f1, only its parent dir. After a crash the rm -rf must
be replayed. This must be able to recurse down the entire
directory tree. The inode link count fixup code takes care of the
ugly details.
Signed-off-by: Chris Mason <chris.mason@oracle.com>
During log replay, inodes are copied from the log to the main filesystem
btrees. Sometimes they have a zero link count in the log but they actually
gain links during the replay or have some in the main btree.
This patch updates the link count to be at least one after copying the
inode out of the log. This makes sure the inode is deleted during an
iput while the rest of the replay code is still working on it.
The log replay has fixup code to make sure that link counts are correct
at the end of the replay, so we could use any non-zero number here and
it would work fine.
Signed-off-by: Chris Mason <chris.mason@oracle.com>
The delayed reference mechanism is responsible for all updates to the
extent allocation trees, including those updates created while processing
the delayed references.
This commit tries to limit the amount of work that gets created during
the final run of delayed refs before a commit. It avoids cowing new blocks
unless it is required to finish the commit, and so it avoids new allocations
that were not really required.
The goal is to avoid infinite loops where we are always making more work
on the final run of delayed refs. Over the long term we'll make a
special log for the last delayed ref updates as well.
Signed-off-by: Chris Mason <chris.mason@oracle.com>
This reads in blocks in the checksum btree before starting the
transaction in btrfs_finish_ordered_io. It makes it much more likely
we'll be able to do operations inside the transaction without
needing any btree reads, which limits transaction latencies overall.
Signed-off-by: Chris Mason <chris.mason@oracle.com>
btrfs_mark_buffer dirty would set dirty bits in the extent_io tree
for the buffers it was dirtying. This may require a kmalloc and it
was not atomic. So, anyone who called btrfs_mark_buffer_dirty had to
set any btree locks they were holding to blocking first.
This commit changes dirty tracking for extent buffers to just use a flag
in the extent buffer. Now that we have one and only one extent buffer
per page, this can be safely done without losing dirty bits along the way.
This also introduces a path->leave_spinning flag that callers of
btrfs_search_slot can use to indicate they will properly deal with a
path returned where all the locks are spinning instead of blocking.
Many of the btree search callers now expect spinning paths,
resulting in better btree concurrency overall.
Signed-off-by: Chris Mason <chris.mason@oracle.com>
Commits are fairly expensive, and so btrfs has code to sit around for a while
during the commit and let new writers come in.
But, while we're sitting there, new delayed refs might be added, and those
can be expensive to process as well. Unless the transaction is very very
young, it makes sense to go ahead and let the commit finish without hanging
around.
The commit grow loop isn't as important as it used to be, the fsync logging
code handles most performance critical syncs now.
Signed-off-by: Chris Mason <chris.mason@oracle.com>
This reduces contention on the extent buffer spin locks by testing for a
blocking lock before trying to take the spinlock.
Signed-off-by: Chris Mason <chris.mason@oracle.com>
The fs/btrfs/inode.c code to run delayed allocation during writout
needed some stack usage optimization. This is the first pass, it does
the check for compression earlier on, which allows us to do the common
(no compression) case higher up in the call chain.
Signed-off-by: Chris Mason <chris.mason@oracle.com>
To avoid deadlocks and reduce latencies during some critical operations, some
transaction writers are allowed to jump into the running transaction and make
it run a little longer, while others sit around and wait for the commit to
finish.
This is a bit unfair, especially when the callers that jump in do a bunch
of IO that makes all the others procs on the box wait. This commit
reduces the stalls this produces by pre-reading file extent pointers
during btrfs_finish_ordered_io before the transaction is joined.
It also tunes the drop_snapshot code to politely wait for transactions
that have started writing out their delayed refs to finish. This avoids
new delayed refs being flooded into the queue while we're trying to
close off the transaction.
Signed-off-by: Chris Mason <chris.mason@oracle.com>
The delayed reference queue maintains pending operations that need to
be done to the extent allocation tree. These are processed by
finding records in the tree that are not currently being processed one at
a time.
This is slow because it uses lots of time searching through the rbtree
and because it creates lock contention on the extent allocation tree
when lots of different procs are running delayed refs at the same time.
This commit changes things to grab a cluster of refs for processing,
using a cursor into the rbtree as the starting point of the next search.
This way we walk smoothly through the rbtree.
Signed-off-by: Chris Mason <chris.mason@oracle.com>
When extents are freed, it is likely that we've removed the last
delayed reference update for the extent. This checks the delayed
ref tree when things are freed, and if no ref updates area left it
immediately processes the delayed ref.
Signed-off-by: Chris Mason <chris.mason@oracle.com>
Many of the tree balancing functions follow the same pattern.
1) cow a block
2) do something to the result
This commit breaks them up into two functions so the variables and
code required for part two don't suck down stack during part one.
Signed-off-by: Chris Mason <chris.mason@oracle.com>
The extent allocation tree maintains a reference count and full
back reference information for every extent allocated in the
filesystem. For subvolume and snapshot trees, every time
a block goes through COW, the new copy of the block adds a reference
on every block it points to.
If a btree node points to 150 leaves, then the COW code needs to go
and add backrefs on 150 different extents, which might be spread all
over the extent allocation tree.
These updates currently happen during btrfs_cow_block, and most COWs
happen during btrfs_search_slot. btrfs_search_slot has locks held
on both the parent and the node we are COWing, and so we really want
to avoid IO during the COW if we can.
This commit adds an rbtree of pending reference count updates and extent
allocations. The tree is ordered by byte number of the extent and byte number
of the parent for the back reference. The tree allows us to:
1) Modify back references in something close to disk order, reducing seeks
2) Significantly reduce the number of modifications made as block pointers
are balanced around
3) Do all of the extent insertion and back reference modifications outside
of the performance critical btrfs_search_slot code.
#3 has the added benefit of greatly reducing the btrfs stack footprint.
The extent allocation tree modifications are done without the deep
(and somewhat recursive) call chains used in the past.
These delayed back reference updates must be done before the transaction
commits, and so the rbtree is tied to the transaction. Throttling is
implemented to help keep the queue of backrefs at a reasonable size.
Since there was a similar mechanism in place for the extent tree
extents, that is removed and replaced by the delayed reference tree.
Yan Zheng <yan.zheng@oracle.com> helped review and fixup this code.
Signed-off-by: Chris Mason <chris.mason@oracle.com>
In order to avoid doing expensive extent management with tree locks held,
btrfs_search_slot will preallocate tree blocks for use by COW without
any tree locks held.
A later commit moves all of the extent allocation work for COW into
a delayed update mechanism, and this preallocation will no longer be
required.
Signed-off-by: Chris Mason <chris.mason@oracle.com>
The full flag on the space info structs tells the allocator not to try
and allocate more chunks because the devices in the FS are fully allocated.
When more devices are added, we need to clear the full flag so the allocator
knows it has more space available.
Signed-off-by: Chris Mason <chris.mason@oracle.com>
Storage allocated to different raid levels in btrfs is tracked by
a btrfs_space_info structure, and all of the current space_infos are
collected into a list_head.
Most filesystems have 3 or 4 of these structs total, and the list is
only changed when new raid levels are added or at unmount time.
This commit adds rcu locking on the list head, and properly frees
things at unmount time. It also clears the space_info->full flag
whenever new space is added to the FS.
The locking for the space info list goes like this:
reads: protected by rcu_read_lock()
writes: protected by the chunk_mutex
At unmount time we don't need special locking because all the readers
are gone.
Signed-off-by: Chris Mason <chris.mason@oracle.com>
btrfs_tree_locked was being used to make sure a given extent_buffer was
properly locked in a few places. But, it wasn't correct for UP compiled
kernels.
This switches it to using assert_spin_locked instead, and renames it to
btrfs_assert_tree_locked to better reflect how it was really being used.
Signed-off-by: Chris Mason <chris.mason@oracle.com>
This fixes a problem where we could return -ENOSPC when we may actually have
plenty of space, the space is just pinned. Instead of returning -ENOSPC
immediately, commit the transaction first and then try and do the allocation
again.
This patch also does chunk allocation for metadata if we pass the 80%
threshold for metadata space. This will help with stack usage since the chunk
allocation will happen early on, instead of when the allocation is happening.
Signed-off-by: Josef Bacik <jbacik@redhat.com>
This is a step in the direction of better -ENOSPC handling. Instead of
checking the global bytes counter we check the space_info bytes counters to
make sure we have enough space.
If we don't we go ahead and try to allocate a new chunk, and then if that fails
we return -ENOSPC. This patch adds two counters to btrfs_space_info,
bytes_delalloc and bytes_may_use.
bytes_delalloc account for extents we've actually setup for delalloc and will
be allocated at some point down the line.
bytes_may_use is to keep track of how many bytes we may use for delalloc at
some point. When we actually set the extent_bit for the delalloc bytes we
subtract the reserved bytes from the bytes_may_use counter. This keeps us from
not actually being able to allocate space for any delalloc bytes.
Signed-off-by: Josef Bacik <jbacik@redhat.com>
btrfs_record_root_in_trans needs the trans_mutex held to make sure two
callers don't race to setup the root in a given transaction. This adds
it to all the places that were missing it.
Signed-off-by: Yan Zheng <zheng.yan@oracle.com>
Btrfs is currently using spin_lock_nested with a nested value based
on the tree depth of the block. But, this doesn't quite work because
the max tree depth is bigger than what spin_lock_nested can deal with,
and because locks are sometimes taken before the level field is filled in.
The solution here is to use lockdep_set_class_and_name instead, and to
set the class before unlocking the pages when the block is read from the
disk and just after init of a freshly allocated tree block.
btrfs_clear_path_blocking is also changed to take the locks in the proper
order, and it also makes sure all the locks currently held are properly
set to blocking before it tries to retake the spinlocks. Otherwise, lockdep
gets upset about bad lock orderin.
The lockdep magic cam from Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Chris Mason <chris.mason@oracle.com>
The call to kzalloc is followed by a kmalloc whose result is stored in the
same variable.
The semantic match that finds the problem is as follows:
(http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@r exists@
local idexpression x;
statement S;
expression E;
identifier f,l;
position p1,p2;
expression *ptr != NULL;
@@
(
if ((x@p1 = \(kmalloc\|kzalloc\|kcalloc\)(...)) == NULL) S
|
x@p1 = \(kmalloc\|kzalloc\|kcalloc\)(...);
...
if (x == NULL) S
)
<... when != x
when != if (...) { <+...x...+> }
x->f = E
...>
(
return \(0\|<+...x...+>\|ptr\);
|
return@p2 ...;
)
@script:python@
p1 << r.p1;
p2 << r.p2;
@@
print "* file: %s kmalloc %s return %s" % (p1[0].file,p1[0].line,p2[0].line)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Chris Mason <chris.mason@oracle.com>
btrfs_init_path was initially used when the path objects were on the
stack. Now all the work is done by btrfs_alloc_path and btrfs_init_path
isn't required.
This patch removes it, and just uses kmem_cache_zalloc to zero out the object.
Signed-off-by: Chris Mason <chris.mason@oracle.com>
btrfs_releasepage may call kmem_cache_alloc indirectly,
and provide same GFP flags it gets to kmem_cache_alloc.
So it's possible to use __GFP_HIGHMEM with the slab
allocator.
Signed-off-by: Yan Zheng <zheng.yan@oracle.com>
Cleaning old snapshots can make sync(1) somewhat slow, and some users
and applications still use it in a global fsync kind of workload.
This patch changes btrfs not to clean old snapshots during sync, which is
safe from a FS consistency point of view. The major downside is that it
makes it difficult to tell when old snapshots have been reaped and
the space they were using has been reclaimed. A new ioctl will be added
for this purpose instead.
Signed-off-by: Chris Mason <chris.mason@oracle.com>
Larger metadata clusters can significantly improve writeback performance
on ssd drives with large erasure blocks. The larger clusters make it
more likely a given IO will completely overwrite the ssd block, so it
doesn't have to do an internal rwm cycle.
On spinning media, lager metadata clusters end up spreading out the
metadata more over time, which makes fsck slower, so we don't want this
to be the default.
Signed-off-by: Chris Mason <chris.mason@oracle.com>
Btrfs wasn't parsing any new mount options during remount, making it
difficult to set mount options on a root drive.
Signed-off-by: Chris Mason <chris.mason@oracle.com>
Theres a slight problem with finish_current_insert, if we set all to 1 and then
go through and don't actually skip any of the extents on the pending list, we
could exit right after we've added new extents.
This is a problem because by inserting the new extents we could have gotten new
COW's to happen and such, so we may have some pending updates to do or even
more inserts to do after that.
So this patch will only exit if we have never skipped any of the extents in the
pending list, and we have no extents to insert, this will make sure that all of
the pending work is truly done before we return. I've been running with this
patch for a few days with all of my other testing and have not seen issues.
Thanks,
Signed-off-by: Josef Bacik <jbacik@redhat.com>
Btrfs was using spin_is_contended to see if it should drop locks before
doing extent allocations during btrfs_search_slot. The idea was to avoid
expensive searches in the tree unless the lock was actually contended.
But, spin_is_contended is specific to the ticket spinlocks on x86, so this
is causing compile errors everywhere else.
In practice, the contention could easily appear some time after we started
doing the extent allocation, and it makes more sense to always drop the lock
instead.
Signed-off-by: Chris Mason <chris.mason@oracle.com>
The S_ISGID check in btrfs_new_inode caused an oops during subvol creation
because sometimes the dir is null.
Signed-off-by: Chris Mason <chris.mason@oracle.com>
On fast devices that go from congested to uncongested very quickly, pdflush
is waiting too often in congestion_wait, and the FS is backing off to
easily in write_cache_pages.
For now, fix this on the btrfs side by only checking congestion after
some bios have already gone down. Longer term a real fix is needed
for pdflush, but that is a larger project.
Signed-off-by: Chris Mason <chris.mason@oracle.com>
Whenever an item deletion is done, we need to balance all the nodes
in the tree to make sure we don't end up with an empty node if a pointer
is deleted. This balance prep happens from the root of the tree down
so we can drop our locks as we go.
reada_for_balance was triggering read-ahead on neighboring nodes even
when no balancing was required. This adds an extra check to avoid
calling balance_level() and avoid reada_for_balance() when a balance
won't be required.
Signed-off-by: Chris Mason <chris.mason@oracle.com>
btrfs_unlock_up_safe would break out at the first NULL node entry or
unlocked node it found in the path.
Some of the callers have missing nodes at the lower levels of the path, so this
commit fixes things to check all the nodes in the path before returning.
Signed-off-by: Chris Mason <chris.mason@oracle.com>
btrfs_del_leaf does two things. First it removes the pointer in the
parent, and then it frees the block that has the leaf. It has the
parent node locked for both operations.
But, it only needs the parent locked while it is deleting the pointer.
After that it can safely free the block without the parent locked.
Signed-off-by: Chris Mason <chris.mason@oracle.com>
btrfs_truncate_inode_items is setup to stop doing btree searches when
it has finished removing the items for the inode. It used to detect the
end of the inode by looking for an objectid that didn't match the
one we were searching for.
But, this would result in an extra search through the btree, which
adds extra balancing and cow costs to the operation.
This commit adds a check to see if we found the inode item, which means
we can stop searching early.
Signed-off-by: Chris Mason <chris.mason@oracle.com>
The compression code had some checks to make sure we were only
compressing bytes inside of i_size, but it wasn't catching every
case. To make things worse, some incorrect math about the number
of bytes remaining would make it try to compress more pages than the
file really had.
The fix used here is to fall back to the non-compression code in this
case, which does all the proper cleanup of delalloc and other accounting.
Signed-off-by: Chris Mason <chris.mason@oracle.com>
With selinux on we end up calling __btrfs_setxattr when we create an inode,
which calls btrfs_start_transaction(). The problem is we've already called
that in btrfs_new_inode, and in btrfs_start_transaction we end up doing a
wait_current_trans(). If btrfs-transaction has started committing it will wait
for all handles to finish, while the other process is waiting for the
transaction to commit. This is fixed by using btrfs_join_transaction, which
won't wait for the transaction to commit. Thanks,
Signed-off-by: Josef Bacik <jbacik@redhat.com>
Before this patch, new files/dirs would ignore the SGID bit on their
parent directory and always be owned by the creating user's uid/gid.
Signed-off-by: Chris Ball <cjb@laptop.org>
Signed-off-by: Chris Mason <chris.mason@oracle.com>
Every transaction in btrfs creates a new snapshot, and then schedules the
snapshot from the last transaction for deletion. Snapshot deletion
works by walking down the btree and dropping the reference counts
on each btree block during the walk.
If if a given leaf or node has a reference count greater than one,
the reference count is decremented and the subtree pointed to by that
node is ignored.
If the reference count is one, walking continues down into that node
or leaf, and the references of everything it points to are decremented.
The old code would try to work in small pieces, walking down the tree
until it found the lowest leaf or node to free and then returning. This
was very friendly to the rest of the FS because it didn't have a huge
impact on other operations.
But it wouldn't always keep up with the rate that new commits added new
snapshots for deletion, and it wasn't very optimal for the extent
allocation tree because it wasn't finding leaves that were close together
on disk and processing them at the same time.
This changes things to walk down to a level 1 node and then process it
in bulk. All the leaf pointers are sorted and the leaves are dropped
in order based on their extent number.
The extent allocation tree and commit code are now fast enough for
this kind of bulk processing to work without slowing the rest of the FS
down. Overall it does less IO and is better able to keep up with
snapshot deletions under high load.
Signed-off-by: Chris Mason <chris.mason@oracle.com>
Most of the btrfs metadata operations can be protected by a spinlock,
but some operations still need to schedule.
So far, btrfs has been using a mutex along with a trylock loop,
most of the time it is able to avoid going for the full mutex, so
the trylock loop is a big performance gain.
This commit is step one for getting rid of the blocking locks entirely.
btrfs_tree_lock takes a spinlock, and the code explicitly switches
to a blocking lock when it starts an operation that can schedule.
We'll be able get rid of the blocking locks in smaller pieces over time.
Tracing allows us to find the most common cause of blocking, so we
can start with the hot spots first.
The basic idea is:
btrfs_tree_lock() returns with the spin lock held
btrfs_set_lock_blocking() sets the EXTENT_BUFFER_BLOCKING bit in
the extent buffer flags, and then drops the spin lock. The buffer is
still considered locked by all of the btrfs code.
If btrfs_tree_lock gets the spinlock but finds the blocking bit set, it drops
the spin lock and waits on a wait queue for the blocking bit to go away.
Much of the code that needs to set the blocking bit finishes without actually
blocking a good percentage of the time. So, an adaptive spin is still
used against the blocking bit to avoid very high context switch rates.
btrfs_clear_lock_blocking() clears the blocking bit and returns
with the spinlock held again.
btrfs_tree_unlock() can be called on either blocking or spinning locks,
it does the right thing based on the blocking bit.
ctree.c has a helper function to set/clear all the locked buffers in a
path as blocking.
Signed-off-by: Chris Mason <chris.mason@oracle.com>
Before metadata is written to disk, it is updated to reflect that writeout
has begun. Once this update is done, the block must be cow'd before it
can be modified again.
This update was originally synchronized by using a per-fs spinlock. Today
the buffers for the metadata blocks are locked before writeout begins,
and everyone that tests the flag has the buffer locked as well.
So, the per-fs spinlock (called hash_lock for no good reason) is no
longer required.
Signed-off-by: Chris Mason <chris.mason@oracle.com>
extent_io.c has debugging code to report and free leaked extent_state
and extent_buffer objects at rmmod time. This helps track down
leaks and it saves you from rebooting just to properly remove the
kmem_cache object.
But, the code runs under a fairly expensive spinlock and the checks to
see if it is currently enabled are not entirely consistent. Some use
#ifdef and some #if.
This changes everything to #if and disables the leak checking.
Signed-off-by: Chris Mason <chris.mason@oracle.com>
When a block goes through cow, we update the reference counts of
everything that block points to. The internal pointers of the block
can be in just about any order, and it is likely to have clusters of
things that are close together and clusters of things that are not.
To help reduce the seeks that come with updating all of these reference
counts, sort them by byte number before actual updates are done.
Signed-off-by: Chris Mason <chris.mason@oracle.com>
Tracing shows the delay between when an async thread goes to sleep
and when more work is added is often very short. This commit adds
a little bit of delay and extra checking to the code right before
we schedule out.
It allows more work to be added to the worker
without requiring notifications from other procs.
Signed-off-by: Chris Mason <chris.mason@oracle.com>
Add call to LSM security initialization and save
resulting security xattr for new inodes.
Add xattr support to symlink inode ops.
Set inode->i_op for existing special files.
Signed-off-by: jim owens <jowens@hp.com>
This patch adds a menu entry to kconfig to enable acls for btrfs.
This allows you to enable FS_POSIX_ACL at kernel compile time.
(updated by Jeff Mahoney to make the changes in fs/btrfs/Kconfig instead)
Signed-off-by: Christian Hesse <mail@earthworm.de>
Signed-off-by: Jeff Mahoney <jeffm@suse.com>
The async bio submission thread was missing some bios that were
added after it had decided there was no work left to do.
Signed-off-by: Chris Mason <chris.mason@oracle.com>
After btrfs_readdir has gone through all the directory items, it
sets the directory f_pos to the largest possible int. This way
applications that mix readdir with creating new files don't
end up in an endless loop finding the new directory items as they go.
It was a workaround for a bug in git, but the assumption was that if git
could make this looping mistake than it would be a common problem.
The largest possible int chosen was INT_LIMIT(typeof(file->f_pos),
and it is possible for that to be a larger number than 32 bit glibc
expects to come out of readdir.
This patches switches that to INT_LIMIT(off_t), which should keep
applications happy on 32 and 64 bit machines.
Signed-off-by: Chris Mason <chris.mason@oracle.com>
Just before reading a leaf, btrfs scans the node for blocks that are
close by and reads them too. It tries to build up a large window
of IO looking for blocks that are within a max distance from the top
and bottom of the IO window.
This patch changes things to just look for blocks within 64k of the
target block. It will trigger less IO and make for lower latencies on
the read size.
Signed-off-by: Chris Mason <chris.mason@oracle.com>
Now that bmap support is gone, this is the only way to get extent
mappings for userland. These are still not valid for IO, but they
can tell us if a file has holes or how much fragmentation there is.
Signed-off-by: Yehuda Sadeh <yehuda@hq.newdream.net>
Swapfiles use bmap to build a list of extents belonging to the file,
and they assume these extents won't change over the life of the file.
They also use resulting list to do IO directly to the block device.
This causes problems for btrfs in a few ways:
btrfs returns logical block numbers through bmap, and these are not suitable
for IO. They might translate to different devices, raid etc.
COW means that file block mappings are going to change frequently.
Using swapfiles on btrfs will lead to corruption, so we're avoiding the
problem for now by dropping bmap support entirely. A later commit
will add fiemap support for people that really want to know how
a file is laid out.
Signed-off-by: Chris Mason <chris.mason@oracle.com>
To improve performance, btrfs_sync_log merges tree log sync
requests. But it wrongly merges sync requests for different
tree logs. If multiple tree logs are synced at the same time,
only one of them actually gets synced.
This patch has following changes to fix the bug:
Move most tree log related fields in btrfs_fs_info to
btrfs_root. This allows merging sync requests separately
for each tree log.
Don't insert root item into the log root tree immediately
after log tree is allocated. Root item for log tree is
inserted when log tree get synced for the first time. This
allows syncing the log root tree without first syncing all
log trees.
At tree-log sync, btrfs_sync_log first sync the log tree;
then updates corresponding root item in the log root tree;
sync the log root tree; then update the super block.
Signed-off-by: Yan Zheng <zheng.yan@oracle.com>
replace_one_extent searches tree leaves for references to a given extent. It
stops searching if it goes beyond the last possible position.
The last possible position is computed by adding the starting offset of a found
file extent to the full size of the extent. The code uses physical size of the
extent as the full size. This is incorrect when compression is used.
The fix is get the full size from ram_bytes field of file extent item.
Signed-off-by: Yan Zheng <zheng.yan@oracle.com>
Change one typedef to a regular enum, and remove an unused one.
Signed-off-by: Jan Engelhardt <jengelh@medozas.de>
Signed-off-by: Chris Mason <chris.mason@oracle.com>
btrfs_extent_post_op calls finish_current_insert and del_pending_extents. They
both may enter infinite loops.
finish_current_insert enters infinite loop if it only finds some backrefs to
update. The fix is to check for pending backref updates before restarting the
loop.
The infinite loop in del_pending_extents is due to a the skipped variable
not being properly reset before looping around.
Signed-off-by: Yan Zheng <zheng.yan@oracle.com>
Merge list_for_each* and list_entry to list_for_each_entry*
Signed-off-by: Qinghuang Feng <qhfeng.kernel@gmail.com>
Signed-off-by: Chris Mason <chris.mason@oracle.com>
kthread_run() returns the kthread or ERR_PTR(-ENOMEM), not NULL.
Signed-off-by: Qinghuang Feng <qhfeng.kernel@gmail.com>
Signed-off-by: Chris Mason <chris.mason@oracle.com>
The "devid <xxx> transid <xxx>" printk in btrfs_scan_one_device()
actually follows another printk that doesn't end in a newline (since the
intention is for the two printks to make one line of output), so the
KERN_INFO just ends up messing up the output:
device label exp <6>devid 1 transid 9 /dev/sda5
Fix this by changing the extra KERN_INFO to KERN_CONT.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Signed-off-by: Chris Mason <chris.mason@oracle.com>
Andrew's review of the xattr code revealed some minor issues that this patch
addresses. Just an error return fix, got rid of a useless statement and
commented one of the trickier parts of __btrfs_getxattr.
Signed-off-by: Josef Bacik <jbacik@redhat.com>
Signed-off-by: Chris Mason <chris.mason@oracle.com>
- Remove the unused local variable 'len';
- Check return value of kmalloc().
Signed-off-by: Wang Cong <wangcong@zeuux.org>
Signed-off-by: Chris Mason <chris.mason@oracle.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/mason/btrfs-unstable:
Btrfs: fix ioctl arg size (userland incompatible change!)
Btrfs: Clear the device->running_pending flag before bailing on congestion
The structure used to send device in btrfs ioctl calls was not
properly aligned, and so 32 bit ioctls would not work properly on
64 bit kernels.
We could fix this with compat ioctls, but we're just one byte away
and it doesn't make sense at this stage to carry about the compat ioctls
forever at this stage in the project.
This patch brings the ioctl arg up to an evenly aligned 4k.
Signed-off-by: Chris Mason <chris.mason@oracle.com>
Btrfs maintains a queue of async bio submissions so the checksumming
threads don't have to wait on get_request_wait. In order to avoid
extra wakeups, this code has a running_pending flag that is used
to tell new submissions they don't need to wake the thread.
When the threads notice congestion on a single device, they
may decide to requeue the job and move on to other devices. This
makes sure the running_pending flag is cleared before the
job is requeued.
It should help avoid IO stalls by making sure the task is woken up
when new submissions come in.
Signed-off-by: Chris Mason <chris.mason@oracle.com>
Use the standard magic.h for btrfs and squashfs.
Signed-off-by: Qinghuang Feng <qhfeng.kernel@gmail.com>
Cc: Phillip Lougher <phillip@lougher.demon.co.uk>
Cc: Chris Mason <chris.mason@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit c4be0c1dc4 added the ability for
write_super_lockfs to return errors, and renamed them to match. But
btrfs didn't get converted.
Do the minimal conversion to make it compile again.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Each subvolume has an extent_state_tree used to mark metadata
that needs to be sent to disk while syncing the tree. This is
used in addition to the dirty bits on the pages themselves so that
a single subvolume can be sent to disk efficiently in disk order.
Normally this marking happens in btrfs_alloc_free_block, which also does
special recording of dirty tree blocks for the tree log roots.
Yan Zheng noticed that when the root of the log tree is allocated, it is added
to the wrong writeback list. The fix used here is to explicitly set
it dirty as part of tree log creation.
Signed-off-by: Chris Mason <chris.mason@oracle.com>
Checksum verification happens in a helper thread, and there is no
need to mess with interrupts. This switches to kmap() instead.
Signed-off-by: Chris Mason <chris.mason@oracle.com>
This patch contains following things.
1) Limit the max size of btrfs_ordered_sum structure to PAGE_SIZE. This
struct is kmalloced so we want to keep it reasonable.
2) Replace copy_extent_csums by btrfs_lookup_csums_range. This was
duplicated code in tree-log.c
3) Remove replay_one_csum. csum items are replayed at the same time as
replaying file extents. This guarantees we only replay useful csums.
4) nbytes accounting fix.
Signed-off-by: Yan Zheng <zheng.yan@oracle.com>
btrfs_drop_extents doesn't change file extent's ram_bytes
in the case of booked extent. To be consistent, we should
also not change ram_bytes when truncating existing extent.
Signed-off-by: Yan Zheng <zheng.yan@oracle.com>
Snapshot creation happens at a specific time during transaction commit. We
need to make sure the code called by snapshot creation doesn't wait
for the running transaction to commit.
This changes btrfs_delete_inode and finish_pending_snaps to use
btrfs_join_transaction instead of btrfs_start_transaction to avoid deadlocks.
It would be better if btrfs_delete_inode didn't use the join, but the
call path that triggers it is:
btrfs_commit_transaction->create_pending_snapshots->
create_pending_snapshot->btrfs_lookup_dentry->
fixup_tree_root_location->btrfs_read_fs_root->
btrfs_read_fs_root_no_name->btrfs_orphan_cleanup->iput
This will be fixed in a later patch by moving the orphan cleanup to the
cleaner thread.
Signed-off-by: Chris Mason <chris.mason@oracle.com>
This is a patch to fix discard semantic to make Btrfs work with FTL and SSD.
We can improve FTL's performance by telling it which sectors are freed by file
system. But if we don't tell FTL the information of free sectors in proper
time, the transaction mechanism of Btrfs will be destroyed and Btrfs could not
roll back the previous transaction under the power loss condition.
There are some problems in the old implementation:
1, In __free_extent(), the pinned down extents should not be discarded.
2, In free_extents(), the free extents are all pinned, so they need to
be discarded in transaction committing time instead of free_extents().
3, The reserved extent used by log tree should be discard too.
This patch change discard behavior as follows:
1, For the extents which need to be free at once,
we discard them in update_block_group().
2, Delay discarding the pinned extent in btrfs_finish_extent_commit()
when committing transaction.
3, Remove discarding from free_extents() and __free_extent()
4, Add discard interface into btrfs_free_reserved_extent()
5, Discard sectors before updating the free space cache, otherwise,
FTL will destroy file system data.
drop_one_dir_item does not properly update inode's link count. It can be
reproduced by executing following commands:
#touch test
#sync
#rm -f test
#dd if=/dev/zero bs=4k count=1 of=test conv=fsync
#echo b > /proc/sysrq-trigger
This fixes it by adding an BTRFS_ORPHAN_ITEM_KEY for the inode
Signed-off-by: Yan Zheng <zheng.yan@oracle.com>
The data in fs_info->super_for_commit are zeros before the
first transaction commit. If tree log sync and system crash
both occur before the first transaction commit, super block
will get corrupted.
This fixes it by properly filling in the super_for_commit field at
open time.
Signed-off-by: Yan Zheng <zheng.yan@oracle.com>
In clear_state_cb, we should check 'tree->ops->clear_bit_hook' instead
of 'tree->ops->set_bit_hook'.
Signed-off-by: Chris Mason <chris.mason@oracle.com>
