Since some regulators in the system may not support suspend mode
configuration we need to allow some regulators to have a missing
suspend mode configuration. Do this by requiring that disabled
regulators are explicitly flagged and then skip over regulators
that have no state specified.
Try to avoid surprises by warning the if we could set the state
but no configuration is provided. This also ensures that an all
zeros configuration generates a warning rather than silently
disabling the regulator.
Reported-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
The BuckWise DC-DC convertors in WM831x devices support switching to
a second output voltage using the logic level on one of the device
pins. This is intended to allow rapid voltage switching for uses like
cpufreq, replacing the I2C or SPI write used to configure the voltage
of the regulator with a much faster GPIO status change.
This is implemented by keeping the DVS voltage configured as the
maximum voltage permitted for the regulator. If a request is made
for the maximum voltage then the GPIO is used to switch to the DVS
voltage, otherwise the normal ON voltage is updated and used. This
follows the idiom used by most cpufreq drivers, which drop the
minimum voltage as the core frequency is dropped but use a constant
maximum - raising the voltage should normally be fast, but lowering
it may be slower.
Configuration of the DVS MFP on the device should be done externally,
for example via OTP.
Support is present in the hardware for monitoring the status of the
transition using a second GPIO. This is not currently implemented
but platform data is provided for it - the driver currently assumes
that the device will be configured to transition immediately - but
platform data is provided to reduce merge issues once it is.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Tested with a MX25-based custom board.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
* 'for-linus' of git://oss.sgi.com/xfs/xfs:
XFS: Free buffer pages array unconditionally
xfs: kill xfs_bmbt_rec_32/64 types
xfs: improve metadata I/O merging in the elevator
xfs: check for not fully initialized inodes in xfs_ireclaim
* 'next' of git://git.secretlab.ca/git/linux-2.6: (23 commits)
powerpc: fix up for mmu_mapin_ram api change
powerpc: wii: allow ioremap within the memory hole
powerpc: allow ioremap within reserved memory regions
wii: use both mem1 and mem2 as ram
wii: bootwrapper: add fixup to calc useable mem2
powerpc: gamecube/wii: early debugging using usbgecko
powerpc: reserve fixmap entries for early debug
powerpc: wii: default config
powerpc: wii: platform support
powerpc: wii: hollywood interrupt controller support
powerpc: broadway processor support
powerpc: wii: bootwrapper bits
powerpc: wii: device tree
powerpc: gamecube: default config
powerpc: gamecube: platform support
powerpc: gamecube/wii: flipper interrupt controller support
powerpc: gamecube/wii: udbg support for usbgecko
powerpc: gamecube/wii: do not include PCI support
powerpc: gamecube/wii: declare as non-coherent platforms
powerpc: gamecube/wii: introduce GAMECUBE_COMMON
...
Fix up conflicts in arch/powerpc/mm/fsl_booke_mmu.c.
Hopefully even close to correctly.
* 'drm-vmware-staging' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6:
drm/vmwgfx: Add DRM driver for VMware Virtual GPU
drm/vmwgfx: Add svga headers for vmwgfx driver
drm/ttm: Add more driver type enums
* 'hwpoison' of git://git.kernel.org/pub/scm/linux/kernel/git/ak/linux-mce-2.6: (34 commits)
HWPOISON: Remove stray phrase in a comment
HWPOISON: Try to allocate migration page on the same node
HWPOISON: Don't do early filtering if filter is disabled
HWPOISON: Add a madvise() injector for soft page offlining
HWPOISON: Add soft page offline support
HWPOISON: Undefine short-hand macros after use to avoid namespace conflict
HWPOISON: Use new shake_page in memory_failure
HWPOISON: Use correct name for MADV_HWPOISON in documentation
HWPOISON: mention HWPoison in Kconfig entry
HWPOISON: Use get_user_page_fast in hwpoison madvise
HWPOISON: add an interface to switch off/on all the page filters
HWPOISON: add memory cgroup filter
memcg: add accessor to mem_cgroup.css
memcg: rename and export try_get_mem_cgroup_from_page()
HWPOISON: add page flags filter
mm: export stable page flags
HWPOISON: limit hwpoison injector to known page types
HWPOISON: add fs/device filters
HWPOISON: return 0 to indicate success reliably
HWPOISON: make semantics of IGNORED/DELAYED clear
...
* 'perf-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (52 commits)
perf record: Use per-task-per-cpu events for inherited events
perf record: Properly synchronize child creation
perf events: Allow per-task-per-cpu counters
perf diff: Percent calcs should use double values
perf diff: Change the default sort order to "dso,symbol"
perf diff: Use perf_session__fprintf_hists just like 'perf record'
perf report: Fix cut'n'paste error recently introduced
perf session: Move perf report specific hits out of perf_session__fprintf_hists
perf tools: Move hist entries printing routines from perf report
perf report: Generalize perf_session__fprintf_hists()
perf symbols: Move symbol filtering to event__preprocess_sample()
perf symbols: Adopt the strlists for dso, comm
perf symbols: Make symbol_conf global
perf probe: Fix to show which probe point is not found
perf probe: Check symbols in symtab/kallsyms
perf probe: Check build-id of vmlinux
perf probe: Reject second attempt of adding same-name event
perf probe: Support event name for --add option
perf probe: Add glob matching support on --del
perf probe: Use strlist__for_each macros in probe-event.c
...
* 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs-2.6: (38 commits)
direct I/O fallback sync simplification
ocfs: stop using do_sync_mapping_range
cleanup blockdev_direct_IO locking
make generic_acl slightly more generic
sanitize xattr handler prototypes
libfs: move EXPORT_SYMBOL for d_alloc_name
vfs: force reval of target when following LAST_BIND symlinks (try #7)
ima: limit imbalance msg
Untangling ima mess, part 3: kill dead code in ima
Untangling ima mess, part 2: deal with counters
Untangling ima mess, part 1: alloc_file()
O_TRUNC open shouldn't fail after file truncation
ima: call ima_inode_free ima_inode_free
IMA: clean up the IMA counts updating code
ima: only insert at inode creation time
ima: valid return code from ima_inode_alloc
fs: move get_empty_filp() deffinition to internal.h
Sanitize exec_permission_lite()
Kill cached_lookup() and real_lookup()
Kill path_lookup_open()
...
Trivial conflicts in fs/direct-io.c
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/suspend-2.6:
PM: rwsem.h need not be included into main.c
PM: Remove unnecessary goto from device_resume_noirq()
PM: Add initcall_debug style timing for suspend/resume
PM: allow for usage_count > 0 in pm_runtime_get()
* 'tracing-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
tracing: Fix return of trace_dump_stack()
ksym_tracer: Fix bad cast
tracing/power: Remove two exports
tracing: Change event->profile_count to be int type
tracing: Simplify trace_option_write()
tracing: Remove useless trace option
tracing: Use seq file for trace_clock
tracing: Use seq file for trace_options
function-graph: Allow writing the same val to set_graph_function
ftrace: Call trace_parser_clear() properly
ftrace: Return EINVAL when writing invalid val to set_ftrace_filter
tracing: Move a printk out of ftrace_raw_reg_event_foo()
tracing: Pull up calls to trace_define_common_fields()
tracing: Extract duplicate ftrace_raw_init_event_foo()
ftrace.h: Use common pr_info fmt string
tracing: Add stack trace to irqsoff tracer
tracing: Add trace_dump_stack()
ring-buffer: Move resize integrity check under reader lock
ring-buffer: Use sync sched protection on ring buffer resizing
tracing: Fix wrong usage of strstrip in trace_ksyms
Change all async metadata buffers to use [READ|WRITE]_META I/O types
so that the I/O doesn't get issued immediately. This allows merging of
adjacent metadata requests but still prioritises them over bulk data.
This shows a 10-15% improvement in sequential create speed of small
files.
Don't include the log buffers in this classification - leave them as
sync types so they are issued immediately.
Signed-off-by: Dave Chinner <dgc@sgi.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Alex Elder <aelder@sgi.com>
v2->v1:
.improve debug info as suggedted by Bjorn,Kenji
.API is using uuid string as suggested by Alexey
Add an API to execute _OSC. A lot of devices can have this method, so add a
generic API.
Signed-off-by: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
* 'bugfixes' of git://git.linux-nfs.org/projects/trondmy/nfs-2.6:
NFSv4: Fix a regression in the NFSv4 state manager
NFSv4: Release the sequence id before restarting a CLOSE rpc call
nfs41: fix session fore channel negotiation
nfs41: do not zero seqid portion of stateid on close
nfs: run state manager in privileged mode
nfs: make recovery state manager operations privileged
nfs: enforce FIFO ordering of operations trying to acquire slot
rpc: add a new priority in RPC task
nfs: remove rpc_task argument from nfs4_find_slot
rpc: add rpc_queue_empty function
nfs: change nfs4_do_setlk params to identify recovery type
nfs: do not do a LOOKUP after open
nfs: minor cleanup of session draining
* 'module' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux-2.6-for-linus:
modpost: fix segfault with short symbol names
module: handle ppc64 relocating kcrctabs when CONFIG_RELOCATABLE=y
Kbuild: clear marker out of modpost
module: make MODULE_SYMBOL_PREFIX into a CONFIG option
ARM: unexport symbols used to implement floating point emulation
ARM: use unified discard definition in linker script
x86: don't export inline function
sparc64: don't export static inline pci_ functions
* 'for-2.6.33' of git://linux-nfs.org/~bfields/linux: (42 commits)
nfsd: remove pointless paths in file headers
nfsd: move most of nfsfh.h to fs/nfsd
nfsd: remove unused field rq_reffh
nfsd: enable V4ROOT exports
nfsd: make V4ROOT exports read-only
nfsd: restrict filehandles accepted in V4ROOT case
nfsd: allow exports of symlinks
nfsd: filter readdir results in V4ROOT case
nfsd: filter lookup results in V4ROOT case
nfsd4: don't continue "under" mounts in V4ROOT case
nfsd: introduce export flag for v4 pseudoroot
nfsd: let "insecure" flag vary by pseudoflavor
nfsd: new interface to advertise export features
nfsd: Move private headers to source directory
vfs: nfsctl.c un-used nfsd #includes
lockd: Remove un-used nfsd headers #includes
s390: remove un-used nfsd #includes
sparc: remove un-used nfsd #includes
parsic: remove un-used nfsd #includes
compat.c: Remove dependence on nfsd private headers
...
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (26 commits)
net: sh_eth alignment fix for sh7724 using NET_IP_ALIGN V2
ixgbe: allow tx of pre-formatted vlan tagged packets
ixgbe: Fix 82598 premature copper PHY link indicatation
ixgbe: Fix tx_restart_queue/non_eop_desc statistics counters
bcm63xx_enet: fix compilation failure after get_stats_count removal
packet: dont call sleeping functions while holding rcu_read_lock()
tcp: Revert per-route SACK/DSACK/TIMESTAMP changes.
ipvs: zero usvc and udest
netfilter: fix crashes in bridge netfilter caused by fragment jumps
ipv6: reassembly: use seperate reassembly queues for conntrack and local delivery
sky2: leave PCI config space writeable
sky2: print Optima chip name
x25: Update maintainer.
ipvs: fix synchronization on connection close
netfilter: xtables: document minimal required version
drivers/net/bonding/: : use pr_fmt
can: CAN_MCP251X should depend on HAS_DMA
drivers/net/usb: Correct code taking the size of a pointer
drivers/net/cpmac.c: Correct code taking the size of a pointer
drivers/net/sfc: Correct code taking the size of a pointer
...
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (22 commits)
Input: ALPS - add interleaved protocol support (Dell E6x00 series)
Input: keyboard - don't override beep with a bell
Input: altera_ps2 - fix test of unsigned in altera_ps2_probe()
Input: add mc13783 touchscreen driver
Input: ep93xx_keypad - update driver to new core support
Input: wacom - separate pen from express keys on Graphire
Input: wacom - add defines for data packet report IDs
Input: wacom - add support for new LCD tablets
Input: wacom - add defines for packet lengths of various devices
Input: wacom - ensure the device is initialized properly upon resume
Input: at32psif - do not sleep in atomic context
Input: i8042 - add Gigabyte M1022M to the noloop list
Input: i8042 - allow installing platform filters for incoming data
Input: i8042 - fix locking in interrupt routine
Input: ALPS - do not set REL_X/REL_Y capabilities on the touchpad
Input: document use of input_event() function
Input: sa1111ps2 - annotate probe() and remove() methods
Input: ambakmi - annotate probe() and remove() methods
Input: gscps2 - fix probe() and remove() annotations
Input: altera_ps2 - add annotations to probe and remove methods
...
* git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6: (33 commits)
sh: Fix test of unsigned in se7722_irq_demux()
sh: mach-ecovec24: Add FSI sound support
sh: mach-ecovec24: Add mt9t112 camera support
sh: mach-ecovec24: Add tw9910 support
sh: MSIOF/mmc_spi platform data for the Ecovec24 board
sh: ms7724se: Add ak4642 support
sh: Fix up FPU build for SH5
sh: Remove old early serial console code V2
sh: sh5 scif pdata (sh5-101/sh5-103)
sh: sh4a scif pdata (sh7757/sh7763/sh7770/sh7780/sh7785/sh7786/x3)
sh: sh4a scif pdata (sh7343/sh7366/sh7722/sh7723/sh7724)
sh: sh4 scif pdata (sh7750/sh7760/sh4-202)
sh: sh3 scif pdata (sh7705/sh770x/sh7710/sh7720)
sh: sh2a scif pdata (sh7201/sh7203/sh7206/mxg)
sh: sh2 scif pdata (sh7616)
sh-sci: Extend sh-sci driver with early console V2
sh: Stub in P3 ioremap support for nommu parts.
sh: wire up vmallocinfo support in ioremap() implementations.
sh: Make the unaligned trap handler always obey notification levels.
sh: Couple kernel and user write page perm bits for CONFIG_X2TLB
...
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/djbw/async_tx:
ppc440spe-adma: adds updated ppc440spe adma driver
iop-adma.c: use resource_size()
dmaengine: clarify the meaning of the DMA_CTRL_ACK flag
sh: stylistic improvements for the DMA driver
dmaengine: fix dmatest to verify minimum transfer length and test buffer size
sh: DMA driver has to specify its alignment requirements
Add COH 901 318 DMA block driver v5
* git://git.infradead.org/mtd-2.6: (90 commits)
jffs2: Fix long-standing bug with symlink garbage collection.
mtd: OneNAND: Fix test of unsigned in onenand_otp_walk()
mtd: cfi_cmdset_0002, fix lock imbalance
Revert "mtd: move mxcnd_remove to .exit.text"
mtd: m25p80: add support for Macronix MX25L4005A
kmsg_dump: fix build for CONFIG_PRINTK=n
mtd: nandsim: add support for 4KiB pages
mtd: mtdoops: refactor as a kmsg_dumper
mtd: mtdoops: make record size configurable
mtd: mtdoops: limit the maximum mtd partition size
mtd: mtdoops: keep track of used/unused pages in an array
mtd: mtdoops: several minor cleanups
core: Add kernel message dumper to call on oopses and panics
mtd: add ARM pismo support
mtd: pxa3xx_nand: Fix PIO data transfer
mtd: nand: fix multi-chip suspend problem
mtd: add support for switching old SST chips into QRY mode
mtd: fix M29W800D dev_id and uaddr
mtd: don't use PF_MEMALLOC
mtd: Add bad block table overrides to Davinci NAND driver
...
Fixed up conflicts (mostly trivial) in
drivers/mtd/devices/m25p80.c
drivers/mtd/maps/pcmciamtd.c
drivers/mtd/nand/pxa3xx_nand.c
kernel/printk.c
* git://git.infradead.org/iommu-2.6:
implement early_io{re,un}map for ia64
Revert "Intel IOMMU: Avoid memory allocation failures in dma map api calls"
intel-iommu: ignore page table validation in pass through mode
intel-iommu: Fix oops with intel_iommu=igfx_off
intel-iommu: Check for an RMRR which ends before it starts.
intel-iommu: Apply BIOS sanity checks for interrupt remapping too.
intel-iommu: Detect DMAR in hyperspace at probe time.
dmar: Fix build failure without NUMA, warn on bogus RHSA tables and don't abort
iommu: Allocate dma-remapping structures using numa locality info
intr_remap: Allocate intr-remapping table using numa locality info
dmar: Allocate queued invalidation structure using numa locality info
dmar: support for parsing Remapping Hardware Static Affinity structure
* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-2.6: (116 commits)
V4L/DVB (13698): pms: replace asm/uaccess.h to linux/uaccess.h
V4L/DVB (13690): radio/si470x: #include <sched.h>
V4L/DVB (13688): au8522: modify the attributes of local filter coefficients
V4L/DVB (13687): cx231xx: use NULL when pointer is needed
V4L/DVB: Davinci VPFE Capture: remove unused #include <linux/version.h>
V4L/DVB (13685): Correct code taking the size of a pointer
V4L/DVB (13684): Fix some cut-and-paste noise in dib0090.h
V4L/DVB (13683): sanio-ms: clean up init, exit and id_table
V4L/DVB (13682): dib8000: make some constant static
V4L/DVB: lgs8gxx: Use shifts rather than multiply/divide when possible
V4L/DVB (13680b): DocBook/media: create links for included sources
V4L/DVB (13680a): DocBook/media: copy images after building HTML
V4L/DVB (13678): Add support for yet another DvbWorld, TeVii and Prof USB devices
V4L/DVB (13676): configurable IRQ mode on NetUP Dual DVB-S2 CI; IRQ from CAM processing (CI interface works faster)
V4L/DVB (13674): stv090x: Add DiSEqC envelope mode
V4L/DVB (13673): lnbp21: Implement 22 kHz tone control
V4L/DVB (13671): sh_mobile_ceu_camera: Remove frame size page alignment
V4L/DVB (13670): soc-camera: Add mt9t112 camera driver
V4L/DVB (13669): tw9910: Add sync polarity support
V4L/DVB (13668): tw9910: remove cropping
...
* akpm: (173 commits)
genalloc: use bitmap_find_next_zero_area
ia64: use bitmap_find_next_zero_area
sparc: use bitmap_find_next_zero_area
mlx4: use bitmap_find_next_zero_area
isp1362-hcd: use bitmap_find_next_zero_area
iommu-helper: use bitmap library
bitmap: introduce bitmap_set, bitmap_clear, bitmap_find_next_zero_area
qnx4: use hweight8
qnx4fs: remove remains of the (defunct) write support
resource: constify arg to resource_size() and resource_type()
gru: send cross partition interrupts using the gru
gru: function to generate chipset IPI values
gru: update driver version number
gru: improve GRU TLB dropin statistics
gru: fix GRU interrupt race at deallocate
gru: add hugepage support
gru: fix bug in allocation of kernel contexts
gru: update GRU structures to match latest hardware spec
gru: check for correct GRU chiplet assignment
gru: remove stray local_irq_enable
...
Currently the locking in blockdev_direct_IO is a mess, we have three different
locking types and very confusing checks for some of them. The most
complicated one is DIO_OWN_LOCKING for reads, which happens to not actually be
used.
This patch gets rid of the DIO_OWN_LOCKING - as mentioned above the read case
is unused anyway, and the write side is almost identical to DIO_NO_LOCKING.
The difference is that DIO_NO_LOCKING always sets the create argument for
the get_blocks callback to zero, but we can easily move that to the actual
get_blocks callbacks. There are four users of the DIO_NO_LOCKING mode:
gfs already ignores the create argument and thus is fine with the new
version, ocfs2 only errors out if create were ever set, and we can remove
this dead code now, the block device code only ever uses create for an
error message if we are fully beyond the device which can never happen,
and last but not least XFS will need the new behavour for writes.
Now we can replace the lock_type variable with a flags one, where no flag
means the DIO_NO_LOCKING behaviour and DIO_LOCKING is kept as the first
flag. Separate out the check for not allowing to fill holes into a separate
flag, although for now both flags always get set at the same time.
Also revamp the documentation of the locking scheme to actually make sense.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Now that we cache the ACL pointers in the generic inode all the generic_acl
cruft can go away and generic_acl.c can directly implement xattr handlers
dealing with the full Posix ACL semantics for in-memory filesystems.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Add a flags argument to struct xattr_handler and pass it to all xattr
handler methods. This allows using the same methods for multiple
handlers, e.g. for the ACL methods which perform exactly the same action
for the access and default ACLs, just using a different underlying
attribute. With a little more groundwork it'll also allow sharing the
methods for the regular user/trusted/secure handlers in extN, ocfs2 and
jffs2 like it's already done for xfs in this patch.
Also change the inode argument to the handlers to a dentry to allow
using the handlers mechnism for filesystems that require it later,
e.g. cifs.
[with GFS2 bits updated by Steven Whitehouse <swhiteho@redhat.com>]
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: James Morris <jmorris@namei.org>
Acked-by: Joel Becker <joel.becker@oracle.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Kill the 'update' argument of ima_path_check(), kill
dead code in ima.
Current rules: ima counters are bumped at the same time
when the file switches from put_filp() fodder to fput()
one. Which happens exactly in two places - alloc_file()
and __dentry_open(). Nothing else needs to do that at
all.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
All users outside of fs/ of get_empty_filp() have been removed. This patch
moves the definition from the include/ directory to internal.h so no new
users crop up and removes the EXPORT_SYMBOL. I'd love to see open intents
stop using it too, but that's a problem for another day and a smarter
developer!
Signed-off-by: Eric Paris <eparis@redhat.com>
Acked-by: Miklos Szeredi <miklos@szeredi.hu>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Use bitmap library and kill some unused iommu helper functions.
1. s/iommu_area_free/bitmap_clear/
2. s/iommu_area_reserve/bitmap_set/
3. Use bitmap_find_next_zero_area instead of find_next_zero_area
This cannot be simple substitution because find_next_zero_area
doesn't check the last bit of the limit in bitmap
4. Remove iommu_area_free, iommu_area_reserve, and find_next_zero_area
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Cc: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This introduces new bitmap functions:
bitmap_set: Set specified bit area
bitmap_clear: Clear specified bit area
bitmap_find_next_zero_area: Find free bit area
These are mostly stolen from iommu helper. The differences are:
- Use find_next_bit instead of doing test_bit for each bit
- Rewrite bitmap_set and bitmap_clear
Instead of setting or clearing for each bit.
- Check the last bit of the limit
iommu-helper doesn't want to find such area
- The return value if there is no zero area
find_next_zero_area in iommu helper: returns -1
bitmap_find_next_zero_area: return >= bitmap size
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Cc: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Greg Kroah-Hartman <gregkh@suse.de>
Cc: Lothar Wassmann <LW@KARO-electronics.de>
Cc: Roland Dreier <rolandd@cisco.com>
Cc: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
resource_size() doesn't change the resource it operates on, so the res
parameter can be marked const. Same for resource_type().
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Reviewed-by: WANG Cong <xiyou.wangcong@gmail.com>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Currently the locking in blockdev_direct_IO is a mess, we have three
different locking types and very confusing checks for some of them. The
most complicated one is DIO_OWN_LOCKING for reads, which happens to not
actually be used.
This patch gets rid of the DIO_OWN_LOCKING - as mentioned above the read
case is unused anyway, and the write side is almost identical to
DIO_NO_LOCKING. The difference is that DIO_NO_LOCKING always sets the
create argument for the get_blocks callback to zero, but we can easily
move that to the actual get_blocks callbacks. There are four users of the
DIO_NO_LOCKING mode: gfs already ignores the create argument and thus is
fine with the new version, ocfs2 only errors out if create were ever set,
and we can remove this dead code now, the block device code only ever uses
create for an error message if we are fully beyond the device which can
never happen, and last but not least XFS will need the new behavour for
writes.
Now we can replace the lock_type variable with a flags one, where no flag
means the DIO_NO_LOCKING behaviour and DIO_LOCKING is kept as the first
flag. Separate out the check for not allowing to fill holes into a
separate flag, although for now both flags always get set at the same
time.
Also revamp the documentation of the locking scheme to actually make
sense.
[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Christoph Hellwig <hch@lst.de>
Cc: Dave Chinner <david@fromorbit.com>
Cc: Badari Pulavarty <pbadari@us.ibm.com>
Cc: Jeff Moyer <jmoyer@redhat.com>
Cc: Jens Axboe <jens.axboe@oracle.com>
Cc: Zach Brown <zach.brown@oracle.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Alex Elder <aelder@sgi.com>
Cc: Mark Fasheh <mfasheh@suse.com>
Cc: Joel Becker <joel.becker@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Don't know the reason, but it appears ki_wait field of iocb never gets used.
Signed-off-by: Shaohua Li <shaohua.li@intel.com>
Cc: Jeff Moyer <jmoyer@redhat.com>
Cc: Benjamin LaHaise <bcrl@kvack.org>
Cc: Zach Brown <zach.brown@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Implement shrinking the reserved memory for crash kernel, if it is more
than enough.
For example, if you have already reserved 128M, now you just want 100M,
you can do:
# echo $((100*1024*1024)) > /sys/kernel/kexec_crash_size
Note, you can only do this before loading the crash kernel.
Signed-off-by: WANG Cong <amwang@redhat.com>
Cc: Neil Horman <nhorman@redhat.com>
Acked-by: Eric W. Biederman <ebiederm@xmission.com>
Cc: Andi Kleen <andi@firstfloor.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We have HARD_MSGMAX lower on 64bit than on 32bit, since usually 64bit
machines have more memory than 32bit machines.
Making it higher on 64bit seems reasonable, and keep the original number
on 32bit.
Acked-by: Serge E. Hallyn <serue@us.ibm.com>
Cc: Cedric Le Goater <clg@fr.ibm.com>
Signed-off-by: WANG Cong <amwang@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Based on Nick's findings:
sysv sem has the concept of semaphore arrays that consist out of multiple
semaphores. Atomic operations that affect multiple semaphores are
supported.
The patch is the first step for optimizing simple, single semaphore
operations: In addition to the global list of all pending operations, a
2nd, per-semaphore list with the simple operations is added.
Note: this patch does not make sense by itself, the new list is used
nowhere.
Signed-off-by: Manfred Spraul <manfred@colorfullife.com>
Cc: Nick Piggin <npiggin@suse.de>
Cc: Pierre Peiffer <peifferp@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
No changes in compiled code. The patch adds the new helper, si_fromuser()
and changes check_kill_permission() to use this helper.
The real effect of this patch is that from now we "officially" consider
SEND_SIG_NOINFO signal as "from user-space" signals. This is already true
if we look at the code which uses SEND_SIG_NOINFO, except __send_signal()
has another opinion - see the next patch.
The naming of these special SEND_SIG_XXX siginfo's is really bad
imho. From __send_signal()'s pov they mean
SEND_SIG_NOINFO from user
SEND_SIG_PRIV from kernel
SEND_SIG_FORCED no info
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Cc: Roland McGrath <roland@redhat.com>
Reviewed-by: Sukadev Bhattiprolu <sukadev@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Suggested by Roland.
Change tracehook_report_syscall_exit() to look at step flag and send the
trap signal if needed.
This change affects ia64, microblaze, parisc, powerpc, sh. They pass
nonzero "step" argument to tracehook but since it was ignored the tracee
reports via ptrace_notify(), this is not right and not consistent.
- PTRACE_SETSIGINFO doesn't work
- if the tracer resumes the tracee with signr != 0 the new signal
is generated rather than delivering it
- If PT_TRACESYSGOOD is set the tracee reports the wrong exit_code
I don't have a powerpc machine, but I think this test-case should see the
difference:
#include <unistd.h>
#include <sys/ptrace.h>
#include <sys/wait.h>
#include <assert.h>
#include <stdio.h>
int main(void)
{
int pid, status;
if (!(pid = fork())) {
assert(ptrace(PTRACE_TRACEME) == 0);
kill(getpid(), SIGSTOP);
getppid();
return 0;
}
assert(pid == wait(&status));
assert(ptrace(PTRACE_SETOPTIONS, pid, 0, PTRACE_O_TRACESYSGOOD) == 0);
assert(ptrace(PTRACE_SYSCALL, pid, 0,0) == 0);
assert(pid == wait(&status));
assert(ptrace(PTRACE_SINGLESTEP, pid, 0,0) == 0);
assert(pid == wait(&status));
if (status == 0x57F)
return 0;
printf("kernel bug: status=%X shouldn't have 0x80\n", status);
return 1;
}
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Acked-by: Roland McGrath <roland@redhat.com>
Cc: <linux-arch@vger.kernel.org>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>