Add the SANE SENSE flag to indicate that a device is capable of handling
more than 18-bytes of sense data. This functionality is required for
USB-ATA bridges implementing SAT. A future patch will actually enable this
function for several devices.
The logic behind this is that we can detect support for SANE_SENSE in a few ways:
1) ATA PASS THROUGH (12) or (16) execute successfully
2) SPC-3 or higher is in use
3) A previous CHECK CONDITION occurred with sense format 70-73 and had
a length greater than 18-bytes total
Signed-off-by: Ben Efros <ben@pc-doctor.com>
Signed-off-by: Matthew Dharm <mdharm-usb@one-eyed-alien.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1171) removes us->sensebuf, since it isn't used anywhere.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1170) removes some duplicate entries in unusual_devs.h
and rearranges a few others to put the list in proper numerical order.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1163b) adds a "quirks=" module parameter to usb-storage.
This will allow people to make short-term changes to their
unusual_devs list without rebuilding the entire driver. Testing will
become much easier, and less-sophisticated users will be able to
access their buggy devices after a simple config-file change instead
of having to wait for a new kernel release.
The patch also adds a documentation entry for usb-storage's
"delay_use" parameter, which has been around for years but but was
never listed among the kernel parameters.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1161) changes the interface to
usb_lock_device_for_reset(). The existing interface is apparently not
very clear, judging from the fact that several of its callers don't
use it correctly. The new interface always returns 0 for success and
it always requires the caller to unlock the device afterward.
The new routine will not return immediately if it is called while the
driver's probe method is running. Instead it will wait until the
probe is over and the device has been unlocked. This shouldn't cause
any problems; I don't know of any cases where drivers call
usb_lock_device_for_reset() during probe.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Cc: Pete Zaitcev <zaitcev@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch corrects the issue when one connects a Nokia 5200 cell
phone in data storage mode. If one uses an unpatched unusual_devs.h,
the following messages appear on /var/log/messages:
Dec 12 01:03:24 alberich kernel: usb 4-2: new full speed USB device
using uhci_hcd and address 3
Dec 12 01:03:25 alberich kernel: usb 4-2: configuration #1 chosen from 1 choice
Dec 12 01:03:25 alberich kernel: scsi10 : SCSI emulation for USB Mass
Storage devices
Dec 12 01:03:25 alberich kernel: usb 4-2: New USB device found,
idVendor=0421, idProduct=04bd
Dec 12 01:03:25 alberich kernel: usb 4-2: New USB device strings:
Mfr=1, Product=2, SerialNumber=3
Dec 12 01:03:25 alberich kernel: usb 4-2: Product: Nokia 5200
Dec 12 01:03:25 alberich kernel: usb 4-2: Manufacturer: Nokia
Dec 12 01:03:25 alberich kernel: usb 4-2: SerialNumber: 353930018354523
Dec 12 01:03:25 alberich kernel: usbcore: registered new interface driver ub
Dec 12 01:03:30 alberich kernel: scsi 10:0:0:0: Direct-Access
Nokia Nokia 5200 0000 PQ: 0 AN
SI: 4
Dec 12 01:03:30 alberich kernel: sd 10:0:0:0: [sdg] 3985409 512-byte
hardware sectors (2041 MB)
Dec 12 01:03:30 alberich kernel: sd 10:0:0:0: [sdg] Write Protect is off
Dec 12 01:03:30 alberich kernel: sd 10:0:0:0: [sdg] Assuming drive
cache: write through
Dec 12 01:03:30 alberich kernel: sd 10:0:0:0: [sdg] 3985409 512-byte
hardware sectors (2041 MB)
Dec 12 01:03:30 alberich kernel: sd 10:0:0:0: [sdg] Write Protect is off
Dec 12 01:03:30 alberich kernel: sd 10:0:0:0: [sdg] Assuming drive
cache: write through
Dec 12 01:03:30 alberich kernel: sdg: sdg1
Dec 12 01:03:30 alberich kernel: sd 10:0:0:0: [sdg] Attached SCSI removable disk
Dec 12 01:03:30 alberich kernel: sd 10:0:0:0: Attached scsi generic sg9 type 0
Dec 12 01:03:30 alberich kernel: sd 10:0:0:0: [sdg] Sense Key : No
Sense [current]
Dec 12 01:03:30 alberich kernel: sd 10:0:0:0: [sdg] Add. Sense: No
additional sense information
Dec 12 01:03:30 alberich kernel: sd 10:0:0:0: [sdg] Sense Key : No
Sense [current]
Dec 12 01:03:30 alberich kernel: sd 10:0:0:0: [sdg] Add. Sense: No
additional sense information
Dec 12 01:03:30 alberich kernel: sd 10:0:0:0: [sdg] Sense Key : No
Sense [current]
(...)
The MicroSD card in the phone remains inaccessible and finally the
cell phone turns itself off. The patch solves this problem and makes
the cell phone fully accessible:
[root@alberich kernel-linus-2.6.27.5-1mdv]# df -h
Sist. Arq. Tam Usad Disp Uso% Montado em
/dev/sda6 31G 5,2G 26G 17% /
/dev/sda1 92M 27M 61M 31% /boot
/dev/mapper/homevg-homelv 240G 237G 3,5G 99% /home
/dev/sda3 21G 7,9G 13G 40% /mnt/windows
/dev/sdg1 2,0G 287M 1,7G 15% /media/disk <--------
I've found necessary to use the FL_US_CAPACITY_FIX switch, as without
it the cell phone is recognized but it went berserk when performing
low-level functions on it (a fdisk -l /dev/uba for example).
lsusb -v output follows:
Bus 004 Device 004: ID 0421:04bd Nokia Mobile Phones
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 2.00
bDeviceClass 0 (Defined at Interface level)
bDeviceSubClass 0
bDeviceProtocol 0
bMaxPacketSize0 64
idVendor 0x0421 Nokia Mobile Phones
idProduct 0x04bd
bcdDevice 6.03
iManufacturer 1 Nokia
iProduct 2 Nokia 5200
iSerial 3 353930018354523
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 32
bNumInterfaces 1
bConfigurationValue 1
iConfiguration 0
bmAttributes 0xc0
Self Powered
MaxPower 100mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 2
bInterfaceClass 8 Mass Storage
bInterfaceSubClass 6 SCSI
bInterfaceProtocol 80 Bulk (Zip)
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x81 EP 1 IN
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0040 1x 64 bytes
bInterval 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x01 EP 1 OUT
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0040 1x 64 bytes
bInterval 0
Device Status: 0x0001
Self Powered
Signed-off-by: Paulo Afonso Graner Fessel <pfessel@gmail.com>
Signed-off-by: Phil Dibowitz <phil@ipom.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This device has been released in a new revision which is still buggy.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Phil Dibowitz <phil@ipom.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
I have another Argosy USB storage device, which has the same problem
with the Argosy USB storage device already fixed in 2.6.27.7. But this
device has another product ID (840:84), so this patch adds a new entry
into unusual_devs to fix the mount problem.
I enclose here two patches: one against 2.6.27.8, and another against
the latest linus-git tree.
The information about the Argosy device is like below:
#lsusb -v -d 840:84
Bus 005 Device 005: ID 0840:0084 Argosy Research, Inc.
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 2.00
bDeviceClass 0 (Defined at Interface level)
bDeviceSubClass 0
bDeviceProtocol 0
bMaxPacketSize0 64
idVendor 0x0840 Argosy Research, Inc.
idProduct 0x0084
bcdDevice 0.01
iManufacturer 1 Generic
iProduct 2 USB 2.0 Storage Device
iSerial 3 8400000000002549
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 32
bNumInterfaces 1
bConfigurationValue 1
iConfiguration 0
bmAttributes 0xc0
Self Powered
MaxPower 2mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 2
bInterfaceClass 8 Mass Storage
bInterfaceSubClass 6 SCSI
bInterfaceProtocol 80 Bulk (Zip)
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x01 EP 1 OUT
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0200 1x 512 bytes
bInterval 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x82 EP 2 IN
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0200 1x 512 bytes
bInterval 0
Device Qualifier (for other device speed):
bLength 10
bDescriptorType 6
bcdUSB 2.00
bDeviceClass 0 (Defined at Interface level)
bDeviceSubClass 0
bDeviceProtocol 0
bMaxPacketSize0 64
bNumConfigurations 1
Device Status: 0x0000
(Bus Powered)
Before the patch, dmesg returns a lot of information like below (my
dmesg is overflown):
....
[ 138.833390] sd 7:0:0:0: [sdb] Add. Sense: No additional sense information
[ 138.877631] sd 7:0:0:0: [sdb] Sense Key : No Sense [current]
[ 138.877643] sd 7:0:0:0: [sdb] Add. Sense: No additional sense information
[ 138.921906] sd 7:0:0:0: [sdb] Sense Key : No Sense [current]
[ 138.921923] sd 7:0:0:0: [sdb] Add. Sense: No additional sense information
....
After the fix, dmesg returns below information:
....
usb 5-1: new high speed USB device using ehci_hcd and address 5
usb 5-1: configuration #1 chosen from 1 choice
scsi7 : SCSI emulation for USB Mass Storage devices
usb-storage: device found at 5
usb-storage: waiting for device to settle before scanning
usb-storage: device scan complete
scsi 7:0:0:0: Direct-Access HTS54808 0M9AT00 MG4O PQ: 0 ANSI: 0
sd 7:0:0:0: [sdb] 156301488 512-byte hardware sectors (80026 MB)
sd 7:0:0:0: [sdb] Write Protect is off
sd 7:0:0:0: [sdb] Mode Sense: 03 00 00 00
sd 7:0:0:0: [sdb] Assuming drive cache: write through
sd 7:0:0:0: [sdb] 156301488 512-byte hardware sectors (80026 MB)
sd 7:0:0:0: [sdb] Write Protect is off
sd 7:0:0:0: [sdb] Mode Sense: 03 00 00 00
sd 7:0:0:0: [sdb] Assuming drive cache: write through
sdb: sdb1
sd 7:0:0:0: [sdb] Attached SCSI disk
sd 7:0:0:0: Attached scsi generic sg1 type 0
kjournald starting. Commit interval 5 seconds
EXT3 FS on sdb1, internal journal
EXT3-fs: recovery complete.
EXT3-fs: mounted filesystem with ordered data mode.
Cc: Kuniyasu Suzaki <k.suzaki@aist.go.jp>
Signed-off-by: Nguyen Anh Quynh <aquynh@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1179) updates the unusual_devs entry for Nokia's 5310
phone to include a more recent firmware revision.
This fixes Bugzilla #12099.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Tested-by: Robson Roberto Souza Peixoto <robsonpeixoto@gmail.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2.6.26(.x, cannot remember) could handle the microSD card in my Nokia
3109c attached via USB as mass storage, 2.6.27(.x, up to and included
2.6.27.8) cannot. Please find the attached patch which fixes this
regression, and a copy of /proc/bus/usb/devices with my phone plugged in
running with this patch on Frugalware.
T: Bus=02 Lev=01 Prnt=01 Port=01 Cnt=02 Dev#= 4 Spd=12 MxCh= 0
D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
P: Vendor=0421 ProdID=0063 Rev= 6.01
S: Manufacturer=Nokia
S: Product=Nokia 3109c
S: SerialNumber=359561013742570
C:* #Ifs= 1 Cfg#= 1 Atr=c0 MxPwr=100mA
I:* If#= 0 Alt= 0 #EPs= 2 Cls=08(stor.) Sub=06 Prot=50 Driver=usb-storage
E: Ad=81(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms
E: Ad=01(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms
From: CSÉCSY László <boobaa@frugalware.org>
Cc: Phil Dibowitz <phil@ipom.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds an unusual_devs entry for the Nikon D2H camera.
From: Tobias Kunze Briseño <t@fictive.com>,
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1176) adds an unusual_devs entry for the Mio C520 GPS
unit. Other devices also based on the Mitac hardware use the same USB
interface firmware, so the Vendor and Product names are generalized.
This fixes Bugzilla #11583.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Tested-by: Tamas Kerecsen <kerecsen@bigfoot.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1168) updates the unusual_devs entry for the Nokia 5300.
According to Jorge Lucangeli Obes <t4m5yn@gmail.com>, some existing
models have a revision number lower than the lower limit of the
current entry.
The patch also moves the entry for the Nokia 5310 to its correct place
in the file.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1169) modifies the unusual_devs entry for the Nokia
6300. According to Maciej Gierok <mgierok@gmail.com> and David
McBride <dwm@doc.ic.ac.uk>, the revision limits need to be wider.
This fixes Bugzilla #11768.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Additional sectors were reported by the Nokia 7610 Supernova phone in
usb storage mode. The following patch rectifies the aforementioned
problem.
Signed-off-by: Ricky Wong Yung Fei <evilbladewarrior@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Since commit 65934a9 ("Make USB storage depend on SCSI rather than selecting
it [try #6]") the comment at the top of drivers/usb/storage/Kconfig is
incorrect. Adjust it to the current situation.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Matthew Dharm <mdharm-usb@one-eyed-alien.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The camera reports an incorrect size and fails to handle PREVENT-ALLOW
MEDIUM REMOVAL commands. The patch marks the camera as an unusual dev
and adds the flags to enable the workarounds for both shortcomings.
Signed-off-by: Jens Taprogge <jens.taprogge@taprogge.org>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Phil Dibowitz <phil@ipom.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Here is an entry for the unusual_devs.h file to handle a Mio Moov 330 GPS that
stops responding when it is requested to transfer more than 64KB. The patch is
taken against kernel-2.6.27-git3.
Signed-off-by: Frédéric Marchal <frederic.marchal@wowcompany.co
Signed-off-by: Phil Dibowitz <phil@ipom.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
In this patch, we want to do one thing: add more Huawei product IDs into the
USB driver. Then it can support more Huawei data card devices. So to declare
the unusual device for new Huawei data card devices in unusual_devs.h and to
declare more new product IDs in option.c.
To modify the data value and length in the function of
usb_stor_huawei_e220_init in initializers.c That's because based on the USB
standard, while sending SET_FETURE_D to the device, it requires the
corresponding data to be zero, and its sending length also must be zero. In
our old solution, it can be compatible with our WCDMA data card devices, but
can not support our CDMA data card devices. But in this new solution, it can
be compatible with all of our data card devices.
Signed-off-by: fangxiaozhi <huananhu@huawei.com>
Signed-off-by: Phil Dibowitz <phil@ipom.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Here's the patch that implements the fix you suggested to avoid the
I/O errors that I was running into with my new USB enclosure with a
JMicron USB/ATA bridge, while issuing scsi-io USN or other such
queries used by Fedora's mkinitrd.
http://bugzilla.kernel.org/show_bug.cgi?id=9638#c85
/proc/bus/usb/devices:
T: Bus=01 Lev=01 Prnt=01 Port=07 Cnt=04 Dev#= 5 Spd=480 MxCh= 0
D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
P: Vendor=152d ProdID=2329 Rev= 1.00
S: Manufacturer=JMicron
S: Product=USB to ATA/ATAPI Bridge
S: SerialNumber=DE5088854FFF
C:* #Ifs= 1 Cfg#= 1 Atr=c0 MxPwr= 2mA
I:* If#= 0 Alt= 0 #EPs= 2 Cls=08(stor.) Sub=06 Prot=50 Driver=usb-storage
E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
(patch applied and retested on a modified 2.6.27.2-libre.24.rc1.fc10)
Signed-off-by: Phil Dibowitz <phil@ipom.com>
Cc: Alexandre Oliva <oliva@lsd.ic.unicamp.br>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
USB should not be having it's own printk macros, so remove err() and
use the system-wide standard of dev_err() wherever possible. In the
few places that will not work out, use a basic printk().
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1118) addresses a problem with certain USB mass-storage
devices. These devices sometimes return less data than asked for and
then provide no sense data to explain the problem. Currently
usb-storage leaves it up to the SCSI layer to decide how this should
be handled, and the SCSI layer interprets the lack of sense data to
mean that nothing went wrong. But if we got less data than required
then something definitely _did_ go wrong, and we should say so.
The patch tells the SCSI layer to retry the command when this sort of
thing happens. Retrying may not solve the underlying problem, but
it's better than believing that data was transferred when it wasn't.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The Nokia 5310 Music Xpress phone reports one too many sectors in
usb-storage mode. This patch resolves that.
Signed-off-by: David Almaroad <dalmaroad@gmail.com>
Cc: Matthew Dharm <mdharm-usb@one-eyed-alien.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1136) adds an unusual_devs entry for a version of the
RockChip MP3 player which can't handle the MODE SENSE command used for
write-protect detection.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
I had trouble connecting my cell phone as a storage device - so I added
it to the unusual_devs.h list. I had trouble with the bcdDeviceMin and
Max values - so after some experimenting I made it pretty inclusive.
From: Filip Joelsson <filip@blueturtle.nu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch alters the Sierra Mass Storage patch so that it is non-configurable.
Signed-off-by: Kevin Lloyd <klloyd@sierrawireless.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1120) adds an unusual_devs entry for the Nokia 5300.
Maybe once Nokia releases the Symbian code we'll be able to fix all
the problems it has with the USB mass-storage protocol.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Tested-by: Cedric Godin <cedric@belbone.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
add razr v3xx US_FL_FIX_CAPACITY flag to unusual_devs.h in usb-storage
This is another Motorola phone that incorrectly reports the sector count
(off by one).
Problem Description: io errors when mounting phone's sd-card via the
phones usb port
Steps to reproduce: mount Motorola Razr v3xx phones sd-card on Linux Desktop
via usb cable. Phones USB port must be in memory card mode.
DEBUG output:
Jul 9 19:32:41 micky kernel: Buffer I/O error on device sdd, logical block 3970048
Jul 9 19:32:41 micky kernel: sd 11:0:0:0: [sdd] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE,SUGGEST_OK
Jul 9 19:32:41 micky kernel: sd 11:0:0:0: [sdd] Sense Key : Medium Error [current]
Jul 9 19:32:41 micky kernel: sd 11:0:0:0: [sdd] Add. Sense: No additional sense information
Jul 9 19:32:41 micky kernel: end_request: I/O error, dev sdd, sector 3970048
From: Jost Diederichs <jost@qdusa.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch upgrades the support for the Sierra Wireless TRU-Install
feature (i.e. zeroCD) to allow for future support of Linux enabled
TRU-Install devices.
By default all devices that do not have a Linux enabled TRU-Install
device (i.e. the device does not have a Linux package on the virtual CD
partition) will be switched into "modem mode." Devices that do contain a
Linux package in the TRU-Install virtual CD will be allowed to enumerate
as a CD-Rom so that either (a) a user can install the packaged software
or (b) a user-space application (e.g. udev) can switch it to modem mode.
This patch does allow for manual override by adding a usb-storage module
parameter 'swi_tru_install' which can force the modem into either mode
regardless of what packages it contains.
Signed-off-by: Kevin Lloyd <klloyd@sierrawireless.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1115) adds unusual_devs entries with the IGNORE_RESIDE
flag for the iRiver T10 and the Simple Tech/Datafab CF+SM card
reader. Apparently these devices provide reasonable residue values
for READ and WRITE operations, but not for others like INQUIRY or READ
CAPACITY.
This fixes the iRiver T10 problem reported in Bugzilla #11125.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1119) will help to reduce the clutter of usb-storage's
unusual_devs file by automatically detecting some devices that need
the IGNORE_RESIDUE flag. The idea is that devices should never return
a non-zero residue for an INQUIRY or a READ CAPACITY command unless
they failed to transfer all the requested data. So if one of these
commands transfers a standard amount of data but there is a positive
residue, we know that the residue is bogus and we can set the flag.
This fixes the problems reported in Bugzilla #11125.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
usb-storage: quirk around v1.11 firmware on Nikon D40
https://bugzilla.redhat.com/show_bug.cgi?id=454028
Just as in earlier firmware versions, we need to perform this
quirk for the latest version too.
Speculatively do the entry for the D80 too, as they seem to
have the same firmware problems historically.
Signed-off-by: Dave Jones <davej@redhat.com>
Cc: Johannes Berg <johannes@sipsolutions.net>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1110) reverts an earlier patch meant to help with
Wireless USB host controllers. These controllers can have bulk
maxpacket values larger than 512, which puts unusual constraints on
the sizes of scatter-gather list elements. However it turns out that
the block layer does not provide the support we need to enforce these
constraints; merely changing the DMA alignment mask doesn't help.
Hence there's no reason to keep the original patch. The Wireless USB
problem will have to be solved a different way.
In addition, there is a reason to get rid of the earlier patch. By
dereferencing a pointer stored in the ep_in array of struct
usb_device, the current code risks an invalid memory access when it
runs concurrently with device removal. The members of that array are
cleared before the driver's disconnect method is called, so it should
not try to use them.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch renames the existing usb_reset_device in hub.c to
usb_reset_and_verify_device and renames the existing
usb_reset_composite_device to usb_reset_device. Also the new
usb_reset_and_verify_device does't need to be EXPORTED .
The idea of the patch is that external interface driver
should warn the other interfaces' driver of the same
device before and after reseting the usb device. One interface
driver shoud call _old_ usb_reset_composite_device instead of
_old_ usb_reset_device since it can't assume the device contains
only one interface. The _old_ usb_reset_composite_device
is safe for single interface device also. we rename the two
functions to make the change easily.
This patch is under guideline from Alan Stern.
Signed-off-by: Ming Lei <tom.leiming@gmail.com>
From the current implementation of usb_reset_composite_device
function, the iface parameter is no longer useful. This function
doesn't do something special for the iface usb_interface,compared
with other interfaces in the usb_device. So remove the parameter
and fix the related caller.
Signed-off-by: Ming Lei <tom.leiming@gmail.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch removes CVS keywords that weren't updated for a long time
from comments.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1092) implements "soft" unbinding for usb-storage. When
the disconnect routine is called, all commands and reset delays are
allowed to complete normally until after scsi_remove_host() returns.
This means that the commands needed for an orderly shutdown will be
sent through to the device.
Unlike before, the driver will now execute every command that it
accepts. Hence there's no need for special code to catch unexecuted
commands and fail them.
The new sequence of events when disconnect runs goes as follows:
If the device is truly unplugged, set the DISCONNECTING
flag so we won't try to access it any more.
If the SCSI-scanning thread hasn't started up yet, prevent
it from doing anything by setting the new DONT_SCAN flag.
Then wake it up and wait for it to terminate.
Remove the SCSI host. This unbinds the upper-level drivers,
doing an orderly shutdown. Commands sent to quiesce the
device will be transmitted normally, unless the device is
unplugged.
Set the DISCONNECTING flag so that we won't accept any new
commands that might get submitted (there aren't supposed to be
any) and we won't try to access the device for resets.
Tell the control thread to exit by waking it up with no
pending command, and wait for it to terminate.
Go on to do all the other normal stuff: releasing resources,
freeing memory, and so on.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1090) converts the one remaining semaphore in
usb-storage into a completion.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Cc: Matthew Dharm <mdharm-usb@one-eyed-alien.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1089) separates out the dynamic atomic bitflags and the
static bitfields in usb-storage. Until now the two sorts of flags
have been sharing the same word; this has always been awkward.
To help prevent possible confusion, the two new fields each have a
different name from the original. us->fflags contains the fixed
bitfields (mostly taken from the USB ID table in unusual_devs.h), and
us->dflags contains the dynamic atomic bitflags (used with set_bit,
test_bit, and so on).
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Cc: Matthew Dharm <mdharm-usb@one-eyed-alien.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds support for rev 2 of an existing unusual_devs entry
enabling ROKR W5s to work. Greg, please apply.
From: Javier Smaldone <javier@smaldone.com.ar>
Signed-off-by: Phil Dibowitz <phil@ipom.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
It turns out that the unusual_devs entry for the Motorola M600i needs
another flag. This patch adds it. Thanks to Atte André Jensen
<atte@ballbreaker.dk>.
Signed-off-by: Phil Dibowitz <phil@ipom.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1101) updates the unusual_devs entry for the Cypress
ATACB pass-through. The protocol field is changed from US_PR_BULK to
US_PR_DEVICE, since the Cypress devices already set bInterfaceProtocol
to Bulk-only.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch fixes ordering problems with entries in unusual_devs.h.
Signed-off-by: Phil Dibowitz <phil@ipom.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The attached patch allows to bypass the ZeroCD mechanism for the ET502HS
HDSPA modem, so that it can be mounted as a network device.
Signed-off-by: Mauro Andreolini <andreoli@weblab.ing.unimo.it>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6:
[SCSI] aic94xx: fix section mismatch
[SCSI] u14-34f: Fix 32bit only problem
[SCSI] dpt_i2o: sysfs code
[SCSI] dpt_i2o: 64 bit support
[SCSI] dpt_i2o: move from virt_to_bus/bus_to_virt to dma_alloc_coherent
[SCSI] dpt_i2o: use standard __init / __exit code
[SCSI] megaraid_sas: fix suspend/resume sections
[SCSI] aacraid: Add Power Management support
[SCSI] aacraid: Fix jbod operations scan issues
[SCSI] aacraid: Fix warning about macro side-effects
[SCSI] add support for variable length extended commands
[SCSI] Let scsi_cmnd->cmnd use request->cmd buffer
[SCSI] bsg: add large command support
[SCSI] aacraid: Fix down_interruptible() to check the return value correctly
[SCSI] megaraid_sas; Update the Version and Changelog
[SCSI] ibmvscsi: Handle non SCSI error status
[SCSI] bug fix for free list handling
[SCSI] ipr: Rename ipr's state scsi host attribute to prevent collisions
[SCSI] megaraid_mbox: fix Dell CERC firmware problem
drivers/usb/storage/unusual_devs.h lists the address
linux-usb-devel@lists.sourceforge.net for patches to that file. This
address results in a bounce and a pointer to vger. This patch updates
the address in the header file.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
FIX_CAPACITY is all that's needed.
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Phil Dibowitz <phil@ipom.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1088) adds an unusual_devs entry for Samsung's YP-U3.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Cc: Phil Dibowitz <phil@ipom.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch makes the needlessly global onetouch_release_input() static.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
If USB storage is built-in but input subsystem is made modular then
OneTouch button functionality can not be selected.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Cc: Matthew Dharm <mdharm-usb@one-eyed-alien.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
- struct scsi_cmnd had a 16 bytes command buffer of its own.
This is an unnecessary duplication and copy of request's
cmd. It is probably left overs from the time that scsi_cmnd
could function without a request attached. So clean that up.
- Once above is done, few places, apart from scsi-ml, needed
adjustments due to changing the data type of scsi_cmnd->cmnd.
- Lots of drivers still use MAX_COMMAND_SIZE. So I have left
that #define but equate it to BLK_MAX_CDB. The way I see it
and is reflected in the patch below is.
MAX_COMMAND_SIZE - means: The longest fixed-length (*) SCSI CDB
as per the SCSI standard and is not related
to the implementation.
BLK_MAX_CDB. - The allocated space at the request level
- I have audit all ISA drivers and made sure none use ->cmnd in a DMA
Operation. Same audit was done by Andi Kleen.
(*)fixed-length here means commands that their size can be determined
by their opcode and the CDB does not carry a length specifier, (unlike
the VARIABLE_LENGTH_CMD(0x7f) command). This is actually not exactly
true and the SCSI standard also defines extended commands and
vendor specific commands that can be bigger than 16 bytes. The kernel
will support these using the same infrastructure used for VARLEN CDB's.
So in effect MAX_COMMAND_SIZE means the maximum size command
scsi-ml supports without specifying a cmd_len by ULD's
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
__FUNCTION__ is gcc-specific, use __func__
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1060) makes usb-storage set the DMA alignment mask for
SCSI slaves to match the maxpacket size of the bulk-IN endpoint,
rather than always setting it to 511. For full-speed devices that
mask is too restrictive, and wireless USB devices can have maxpacket
sizes larger than 512.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Since there seems to be little reason to mark the current USB storage
features as "EXPERIMENTAL," remove that dependency.
Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
I have got a cypress usb-ide bridge and I would like to tune or monitor
my disk with tools like hdparm, hddtemp or smartctl.
My controller support a way to send raw ATA command to the disk with
something call atacb (see
http://download.cypress.com.edgesuite.net/design_resources/datasheets/contents/cy7c68300c_8.pdf).
Atacb support can be added for each application, but there is some disadvantages :
- all application need to be patched
- A race is possible if there other accesses, because the emulation can
be split in 2 atacb scsi transactions. One for sending the command, one
for reading the register (if ck_cond is set).
I have implemented the emulation in usb-storage with a special proto_handler,
and an unsual entry.
Signed-off-by: Matthieu CASTET <castet.matthieu@free.fr>
Signed-off-by: Matthew Dharm <mdharm-usb@one-eyed-alien.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
As Torsten Kaiser pointed out, it seems the dependency of
USB_STORAGE_ONETOUCH on !PM should have been removed in commit
7931e1c6f8.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Cc: Matthew Dharm <mdharm-usb@one-eyed-alien.net>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Greg Kroah-Hartman <gregkh@suse.de>
Cc: Torsten Kaiser <just.for.lkml@googlemail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
I converted the usu_init_notify semaphore to normal mutex usage, and it
should still prevent the request_module before the init routine is
complete. Before it acted more like a complete, now the mutex protects two
distinct section from running at the same time.
Signed-off-by: Daniel Walker <dwalker@mvista.com>
Cc: Pete Zaitcev <zaitcev@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
- declare the unusal device for Huawei data card devices in
unusual_devs.h
- disable the product ID matching for Huawei data card devices in
usb_match_device function of driver.c
- declare the product IDs in option.c.
Signed-off-by: fangxiaozhi <huananhu@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Motorola ROKR Z6 cellphone has bugs in its USB, so it is impossible to use
it as mass storage. Patch describes new "unusual" USB device for it with
FIX_INQUIRY and FIX_CAPACITY flags and new BULK_IGNORE_TAG flag.
Last flag relaxes check for equality of bcs->Tag and us->tag in
usb_stor_Bulk_transport routine.
Signed-off-by: Constantin Baranov <const@tltsu.ru>
Signed-off-by: Matthew Dharm <mdharm-usb@one-eyed-alien.net>
Signed-off-by: Daniel Drake <dsd@gentoo.org>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
If the inquiry fails then the info structure on us->extra was not freed.
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-rc-fixes-2.6:
[SCSI] a100u2w: fix bitmap lookup routine
[SCSI] fix media change events for polled devices
[SCSI] sd, sr: do not emit change event at device add
[SCSI] mpt fusion: Power Management fixes for MPT SAS PCI-E controllers
[SCSI] gdth: Allocate sense_buffer to prevent NULL pointer dereference
[SCSI] arcmsr: fix iounmap error for Type B adapter
[SCSI] isd200: Allocate sense_buffer for hacked up scsi_cmnd
[SCSI] fix bsg queue oops with iscsi logout
[SCSI] Fix dependency problems in SCSI drivers
[SCSI] advansys: Fix bug in AdvLoadMicrocode
Since the separation of sense_buffer from scsi_cmnd, Drivers that hack their
own struct scsi_cmnd like here isd200, must also take care of their own
sense_buffer.
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
drivers/usb/storage/sddr55.c: In function 'sddr55_transport':
drivers/usb/storage/sddr55.c:526: warning: 'deviceID' may be used uninitialized in this function
drivers/usb/storage/sddr55.c:525: warning: 'manufacturerID' may be used uninitialized in this function
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1037) makes a small update to the earlier as1035 patch.
The minimum-length computation shouldn't be done in
usb_stor_access_xfer_buf(), since that routine can be called multiple
times for a single transfer. It should be done in
usb_stor_set_xfer_buf() instead, which gets called only once.
The way it is now isn't really _wrong_, but it isn't really _right_
either. Moving the statement will be an improvement.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1035) fixes a bug in usb_stor_access_xfer_buf() (the bug
was originally found by Boaz Harrosh): The routine must not attempt to
write beyond the end of a scatter-gather list or beyond the number of
bytes requested. It also fixes up the formatting of a few comments
and similar whitespace issues.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1033) adds a quirks entry and an unusual_devs entry for
the Actions Semiconductor flash drive. This device has a 64-byte
string descriptor, which it doesn't terminate with a 0-length packet.
Oddly enough, the reporter's logs show that when the device was
plugged in at boot time, it changes its behavior completely -- it uses
a different product ID, product string descriptor, and bDeviceClass.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1034) was written by Leonid Petrov, reported by Robert
Spitzenpfeil, and updated by me. It adds an unusual_devs entry with
the IGNORE_RESIDUE flag for the Oracom MP3 player. Together with the
change to the Get-Max-LUN routine in as1032, it makes the player usable.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Phil Dibowitz <phil@ipom.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add new BCD numbers for Nikon D80 Firmware revision v1.10 to the
unusual_devs.h file.
Signed-off-by: Konstantin Kletschke <konsti@ku-gbr.de>
Signed-off-by: Phil Dibowitz <phil@ipom.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1032) removes the Clear-Halt calls in
usb_stor_Bulk_max_lun(). Evidently some devices (such as the Oracom
MP3 player) really don't like to receive these requests when their
bulk endpoints aren't halted.
The only reason for adding them originally was to get an ancient
ZIP-100 drive to work. But since this device has only a single LUN,
we don't need to send it a Get-Max-LUN request at all. Adding an
unusual_devs entry for the ZIP-100 with the SINGLE_LUN flag set will
cause this step to be skipped.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Now that commit 3794ade5b2 removed
incorrect dependency on CONFIG_IDE we can fix the driver to not
include <linux/ide.h>:
* add ATA_REG_{ERROR,LCYL,HCYL,STATUS}_OFFSET defines and use them
instead of IDE_{ERROR,LCYL,HCYL,STATUS}_OFFSET from <linux/ide.h>
* remove no longer needed <linux/ide.h> include
* remove incorrect comment added by the last commit:
- isd200.c is not the only user of struct hd_driveid besides IDE
(see drivers/block/xsysace.c and arch/um/drivers/ubd_kern.c)
Cc: Alan Cox <alan@redhat.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add "FIX_CAPACITY" entry for HP Photosmart r707 Camera in "Disk" mode.
Camera will wedge when /lib/udev/vol_id attempts to access the last sector,
EIO gets reported to dmesg, and block device is marked "offline" (it is).
Reproduced vol_id behavior with:
"dd if=/dev/sda of=/dev/null skip=60800 count=1"
Cc: stable <stable@kernel.org>
Signed-off-by: Grant Grundler <grundler@parisc-linux.org>
Signed-off-by: Phil Dibowitz <phil@ipom.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
In preparation for bidi we abstract all IO members of scsi_cmnd,
that will need to duplicate, into a substructure.
- Group all IO members of scsi_cmnd into a scsi_data_buffer
structure.
- Adjust accessors to new members.
- scsi_{alloc,free}_sgtable receive a scsi_data_buffer instead of
scsi_cmnd. And work on it.
- Adjust scsi_init_io() and scsi_release_buffers() for above
change.
- Fix other parts of scsi_lib/scsi.c to members migration. Use
accessors where appropriate.
- fix Documentation about scsi_cmnd in scsi_host.h
- scsi_error.c
* Changed needed members of struct scsi_eh_save.
* Careful considerations in scsi_eh_prep/restore_cmnd.
- sd.c and sr.c
* sd and sr would adjust IO size to align on device's block
size so code needs to change once we move to scsi_data_buff
implementation.
* Convert code to use scsi_for_each_sg
* Use data accessors where appropriate.
- tgt: convert libsrp to use scsi_data_buffer
- isd200: This driver still bangs on scsi_cmnd IO members,
so need changing
[jejb: rebased on top of sg_table patches fixed up conflicts
and used the synergy to eliminate use_sg and sg_count]
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
This patch sets the last_sector_bug flag to 1 for all USB disks. This is
needed to makes the cardreader on various HP multifunction printers work.
Since the performance impact is negible we set this flag for all USB disks to
avoid an unusual_devs.h nightmare.
Signed-off-by: Hans de Goede <j.w.r.degoede@hhs.nl>
Acked-by: Matthew Dharm <mdharm-usb@one-eyed-alien.net>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
This patch relaxes the default SCSI DMA alignment from 512 bytes to 4
bytes. I remember from previous discussions that usb and firewire have
sector size alignment requirements, so I upped their alignments in the
respective slave allocs.
The reason for doing this is so that we don't get such a huge amount of
copy overhead in bio_copy_user() for udev. (basically all inquiries it
issues can now be directly mapped).
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
- This patch should be commited before:
usb: transport - convert to accessors and !use_sg code path removal
- isd200_action() was still using direct liniar pointers in issuing
commands to the USB transport level. This is no longer supported,
use one-element scatterlist instead.
- Adjustment of command's length in the case of scsi-to-ata translation
is now restored before return to queuecommand, since other wise it can
leak BIOs.
- isd200_action() return Error on unknown requests. Used to print an error
but still try to send garbage cdb.
- convert few places to scsi data accessors.
- Todo: This file will need to be changed when scsi_cmnd changes to
scsi_data_buffer or any other solution.
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
Acked-by: Matthew Dharm <mdharm-scsi@one-eyed-alien.net>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
- This patch depends on:
usb: transport.c use scsi_eh API in REQUEST_SENSE execution
- Use scsi data accessors and remove of !use_sg code path.
- New usb_stor_bulk_srb() for use by drivers
[jejb: updated with corrective fix.
had a bug in residual handling in the new usb_stor_bulk_srb()
function. Found by Gabriel C. in -mm tree.
Tested-by: Gabriel C <nix.or.die@googlemail.com>
]
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
Acked-by: Matthew Dharm <mdharm-scsi@one-eyed-alien.net>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
- functions that received char* but where passed scatterlist* mostly
were changed to receive void*
- Use scsi data accessors and remove of !use_sg code path
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
Acked-by: Matthew Dharm <mdharm-scsi@one-eyed-alien.net>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
- Use scsi data accessors and remove of !use_sg code path
- This patch is dependent on cleanup patch to usb transport.c/h
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
Acked-by: Matthew Dharm <mdharm-scsi@one-eyed-alien.net>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
- Use scsi data accessors and remove of !use_sg code path
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
Acked-by: Matthew Dharm <mdharm-scsi@one-eyed-alien.net>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
This reverts one change from 67fa10627e
that prevented userspace from seing the "driver disk" lun in a san disk
device. The kernel shouldn't do this, it's up to userspace to handle
this properly, if it somehow wants to filter this away.
Cc: Ben Collins <bcollins@ubuntu.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Phil Dibowitz <phil@ipom.com>
Cc: Kyle McMartin <kyle@mcmartin.ca>
Cc: Matthew Dharm <mdharm-usb@one-eyed-alien.net>
Cc: Hans de Goede <j.w.r.degoede@hhs.nl>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When a device cannot handle the smallest previously limited transfer
size (64 blocks) without stalling, limit the device to the amount of
packets that fit in a platform native page.
The lowest possible limit is PAGE_CACHE_SIZE, so if the device is ever
used on a platform that has larger than 8K pages, you lose unless you
can convince the device firmware folks to fix the issue.
Cc: Mathew Dharm <mdharm-scsi@one-eyed-alien.net>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Pete Zaitcev <zaitcev@redhat.com>
Signed-off-by: Doug Maxey <dwm@austin.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1018) adds an unusual_devs entry for the JetFlash
TS1GJF2A. This device doesn't like read requests for more than 188
sectors. Setting max_sectors down to 64 is overkill, but at least
it will work without errors.
For the torturous debugging history, see this thread:
http://marc.info/?t=118745764700005&r=1&w=2
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1000) sets the SCSI allow_restart flag for USB disk
devices. In theory this should never hurt, and there definitely are
devices out there (such as the Seagate 250-GB external drive) which
need the flag to be set.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The ISD200 driver imports a single trivial routine from the IDE layer and
in doing so creates a mess of dependancies that drag in the entire old
IDE layer. Even more sad - it does this for a routine which is usually
(little endian) a null function!
- Copy the function into ISD200
- Rename it so it doesn't clash with the ide header prototype
- Remove all the depend constraints
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Ben Efros