This patch (as1223) removes a bunch of unnecessary "inline"
annotations from the usbfs driver.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1221) changes the way usbcore reinitializes a device
following a reset or a reset-resume. Currently we call
usb_set_interface() for every interface in the active configuration;
this is to put the interface into the same altsetting as before the
reset and to make sure that the host's endpoint state matches the
device's endpoint state.
However, sending a Set-Interface request is a waste of time if an
interface was already in altsetting 0 before the reset, since it is
certainly in altsetting 0 afterward. In addition, many devices can't
handle Set-Interface requests -- they crash when they receive them.
So instead, the patch adds code to check each interface. If the
interface wasn't in altsetting 0 before the reset, we go head with the
Set-Interface request as before. But if it was then we skip sending
the Set-Interface request, and we clear out the host-side endpoint
state by calling usb_disable_interface() followed by
usb_enable_interface().
The patch also adds a couple of new comments to explain what's going
on.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
actual_length should also be a u32 and not a signed value. This patch
changes this field to be 'u32' to prevent any potential negative
conversion and comparison errors.
This triggered a few compiler warning messages when these fields were
being used with the min macro, so they have also been fixed up in this
patch.
Cc: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Roel Kluin pointed out that transfer_buffer_lengths in struct urb was
declared as an 'int'. This patch changes this field to be 'u32' to
prevent any potential negative conversion and comparison errors.
This triggered a few compiler warning messages when these fields were
being used with the min macro, so they have also been fixed up in this
patch.
Cc: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The code in uhci-q.c doesn't have to use pseudo-negative values. I did
it that way because it was easy and because it would give the expected
output during debugging. But it doesn't have to work that way. Here's
another approach.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Cc: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch disables USB regulators VUSB1V5, VUSB1V8, and VUSB3V1
when the USB cable is unplugged to reduce power consumption.
Added a depencency from twl4030 usb driver to TWL_REGULATOR.
Signed-off-by: Jouni Hogander <jouni.hogander@nokia.com>
Signed-off-by: Kalle Jokiniemi <kalle.jokiniemi@digia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds an extension to the binary API so it reaches parity with
existing text API (so-called "1u"). The extension delivers additional data,
such as ISO descriptors and the interrupt interval.
Signed-Off-By: Pete Zaitcev <zaitcev@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch fixes the following bug:
.plug ch341 usb serial port into a hub port;
.ch341 driver bound to the device and /dev/ttyUSB0 comes
.open /dev/ttyUSB0 by minicom and we can use the serial successfully
.suspend the ch341 usb serial device(such as: echo suspend > power/level)
.resume the ch341 usb serial device (such as: echo on > power/level)
.new port /dev/ttyUSB1 comes ,and the original /dev/ttyUSB0 still exists,
but is no longer usable by minicom
The patch adds suspend and resume callback to ch341 usb driver to prevent it
from unbinding during suspend. The /dev/ttyUSB0 is not released until being
closed, so /dev/ttyUSB1 comes after resume, and the original /dev/ttyUSB0 is
no longer usable by minicom. It is really a mess for a minicom user.
This patch also adds the reset_resume callback to make it usable after resuming
from STR or hibernation, for generally STR or hibernation will make the vbus
of root-hub lost.
Finally enable the driver's supports_autosuspend, for the device is in working
order with it.
Signed-off-by: Ming Lei <tom.leiming@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Partial support for DaVinci DM355, on the EVM board; peripheral
mode should work, once mainline merges DM355 support. Missing:
(a) renumbering the GPIO for DRVVBUS on the DM6446 EVM,
when DAVINCI_N_GPIO increases;
(b) disabling DM355_DEEPSLEEP.DRVVBUS_OVERRIDE so VBUS is
driven according to the ID signal, if cpu_is_..._dm355()
The new PHY control bits are ignored on DM6446.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Except on DaVinci, VBUS is now switched off as part of idling the
USB link (after a_wait_bcon) whenever a device is disconnected
from host. This is correct for OTG hosts, where either SRP or
an ID interrupt could turn VBUS on again.
However, for non-OTG hosts there's no way to turn VBUS on again,
so the host becomes unusable. And the procfs entry which once
allowed a manual workaround for this is now gone.
This patch adds an is_otg_enabled() check before scheduling the
switch-off timer in disconnect path, supporting a "classic host"
mode where SRP is unavailable.
[ dbrownell@users.sourceforge.net: tweak patch description ]
Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Correct musb_read_fifosize() and musb_configure_ep0() functions
for the #ifndef BLACKFIN branch when the silicon uses static FIFO
configuration. (Most current silicon configures this controller
to use dynamic FIFO configuration; some parts from ST don't, like
the STM STA2062.)
Signed-off-by: Giuseppe GORGOGLIONE <giuseppe.gorgoglione@st.com>
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fixes endpoint starvation issue when more than one bulk QH is
multiplexed on the reserved bulk RX endpoint, which is normal
for cases like serial and ethernet adapters.
This patch sets the NAK timeout interval for such QHs, and when
a timeout triggers the next QH will be scheduled. (This resembles
the bulk scheduling done in hardware by EHCI, OHCI, and UHCI.)
This scheme doesn't work for devices which are connected to a
high to full speed tree (transaction translator) as there is
no NAK timeout interrupt from the musb controller from such
devices.
Tested with PIO, Inventra DMA, CPPI DMA.
[ dbrownell@users.sourceforge.net: fold in start_urb() update;
clarify only for bulk RX; don't accidentally clear WZC bits ]
Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com>
Cc: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The current MUSB host code doesn't make use of all the available
FIFOs in for periodic transfers since it wrongly assumes the RX
and TX sides of any given hw_ep always share one FIFO.
Change: use 'in_qh' and 'out_qh' fields of the 'struct musb_hw_ep'
to check the endpoint's business; get rid of the now-unused 'periodic'
array in the 'struct musb'. Also optimize a loop induction variable
in the endpoint lookup code.
(Based on a previous patch from Ajay Kumar Gupta <ajay.gupta@ti.com>)
[ dbrownell@users.sourceforge.net: clarify description and origin
of this fix; whitespace ]
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
To permit a userspace application to associate with WUSB devices
using numeric association, control transfers to unauthenticated WUSB
devices must be allowed.
This requires that wusbcore correctly sets the device state to
UNAUTHENTICATED, DEFAULT and ADDRESS and that control transfers can be
performed to UNAUTHENTICATED devices.
Signed-off-by: David Vrabel <david.vrabel@csr.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The lack of a MODULE_LICENSE macro in ums-* subdrivers prevented them
from loading. Needs to be applied after Alan Stern's usb-storage
subdriver separation patchset. Also added missing MODULE_DESCRIPTION and
MODULE_AUTHOR entries.
Signed-off-by: Maciej Grela <maciej.grela@gmail.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Matthew Dharm <mdharm-usb@one-eyed-alien.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1217) converts usb-storage's onetouch subdriver into a
separate module.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1216) converts usb-storage's karma subdriver into a
separate module.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1215) converts usb-storage's alauda subdriver into a
separate module.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1214) converts usb-storage's jumpshot subdriver into a
separate module.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1213) converts usb-storage's datafab subdriver into a
separate module.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1212) converts usb-storage's freecom subdriver into a
separate module.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1211) converts usb-storage's shuttle_usbat subdriver
into a separate module.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1210) converts usb-storage's cypress_atacb subdriver
into a separate module.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1209) converts usb-storage's sddr55 subdriver into a
separate module.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1208) converts usb-storage's isd200 subdriver into a
separate module.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1207) converts usb-storage's sddr09 subdriver into a
separate module.
An unexpected complication arises because of DPCM devices, in which
one LUN uses the sddr09 transport and one uses the standard CB
transport. Since these devices can be used even when
USB_STORAGE_SDDR09 isn't configured, their entries in unusual_devs.h
require special treatment. If SDDR09 isn't configured then the
entries remain in unusual_devs.h; if it is then the entries are
present in unusual_sddr09.h instead.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1206) is the first step in converting usb-storage's
subdrivers into separate modules. It makes the following large-scale
changes:
Remove a bunch of unnecessary #ifdef's from usb_usual.h.
Not truly necessary, but it does clean things up.
Move the USB device-ID table (which is duplicated between
libusual and usb-storage) into its own source file,
usual-tables.c, and arrange for this to be linked with
either libusual or usb-storage according to whether
USB_LIBUSUAL is configured.
Add to usual-tables.c a new usb_usual_ignore_device()
function to detect whether a particular device needs to be
managed by a subdriver and not by the standard handlers
in usb-storage.
Export a whole bunch of functions in usb-storage, renaming
some of them because their names don't already begin with
"usb_stor_". These functions will be needed by the new
subdriver modules.
Split usb-storage's probe routine into two functions.
The subdrivers will call the probe1 routine, then fill in
their transport and protocol settings, and then call the
probe2 routine.
Take the default cases and error checking out of
get_transport() and get_protocol(), which run during
probe1, and instead put a check for invalid transport
or protocol values into the probe2 function.
Add a new probe routine to be used for standard devices,
i.e., those that don't need a subdriver. This new routine
checks whether the device should be ignored (because it
should be handled by ub or by a subdriver), and if not,
calls the probe1 and probe2 functions.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: Matthew Dharm <mdharm-usb@one-eyed-alien.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
With "nousb" cmdline booting, built-in serial drivers (ie. airecable)
will trigger kernel oops.
Indeed, if nousb, usb_serial_init will failed, and the usb serial bus type
will not be registerd, then usb_serial_register call driver_register
which try to register the driver to a not registered bus.
Here add usb_disabled() check in usb_serial_register to fix it.
Signed-off-by: Dave Young <hidave.darkstar@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fix ehci printk formats:
drivers/usb/host/ehci-q.c:351: warning: format '%d' expects type 'int', but argument 4 has type 'size_t'
drivers/usb/host/ehci-q.c:351: warning: format '%d' expects type 'int', but argument 5 has type 'size_t'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The base versions handle constant folding now.
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Driver originally written by Qualcomm, but rewritten by me due to the
totally different coding style. Cleaned up the probe logic to make a
bit more sense, this is one wierd device. They could have prevented all
of this by just writing sane firmware for the modem.
Cc: Tamm Liu <tamml@qualcomm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
We need to figure out what userspace programs are expecting from this
driver, so log them so we can try to get it right.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This is for the Symbol 6608 barcode scanner in a fake "HID" mode.
Thanks to Dalibor Grgec for working with me to get this to start to work
properly.
Cc: Dalibor Grgec <dalibor.grgec@zemris.fer.hr>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Currently, the driver only supports PCI and PPC_OF but there are
boards like ARM RealView where this is a platform device. The patch adds
the necessary functions and registration to the isp1760-if.c file and
modifies the corresponding Makefile and Kconfig to be able to use this
driver even if PCI and PPC_OF are not enabled.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Cc: Sebastian Siewior <bigeasy@linutronix.de>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The patch changes the prototype of the isp1760_register() function to use
predefined types like phys_addr_t and resource_size_t rather than u64
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Cc: Sebastian Siewior <bigeasy@linutronix.de>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1204) adds a software retry mechanism to ehci-hcd. It
gets invoked when the driver encounters transaction errors on an
asynchronous endpoint. On many systems, hardware deficiencies cause
such errors to occur if one device is unplugged while the host is
communicating with another device. With the patch, the failed
transactions are retried and generally succeed the second or third
time through.
This is based on code originally written by Koichiro Saito.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Tested by: Koichiro Saito <Saito.Koichiro@adniss.jp>
CC: David Brownell <david-b@pacbell.net>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
commit 64a87b24: [SCSI] Let scsi_cmnd->cmnd use request->cmd buffer
changed the scsi_eh_prep_cmnd logic by making it clear
the ->cmnd buffer. But the sat to cypress atacb translation supposed
the ->cmnd buffer wasn't modified.
This patch makes it set the ->cmnd buffer after scsi_eh_prep_cmnd call.
The problem and a fix was reported by Matthieu CASTET <castet.matthieu@free.fr>
It also removes all the hackery fiddling of scsi_cmnd and scsi_eh_save by
requesting from scsi_eh_prep_cmnd to prepare a read into ->sense_buffer,
which is much more suitable a buffer for HW transfers, then after the command
execution the regs read is copied into regs buffer before actual preparation
of sense_buffer.
Also fix an alien comment character to my utf-8 editor.
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
Signed-off-by: Matthieu CASTET <castet.matthieu@free.fr>
Cc: stable <stable@kernel.org>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Cc: Matthew Dharm <mdharm-kernel@one-eyed-alien.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1205) moves timer_action() from ehci.h to ehci-hcd.c and
makes it out-of-line. Over the years it has grown too big to be inline
any more.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Remove old comments about USB_EHCI_HCD.
Cc: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
A USB-serial converter device is plugged into a system, and a process
opens it's device node. If the device is physically removed whilst the
process still has its device node open, then other processes can
sucessfully open the now non-existent device's node. I would expect
that open() on a device that has been physically removed should return
ENODEV.
This is manifesting itself with getty on my system. I do the following:
1. set up inittab to spawn getty on ttyUSB0, eg:
T1:23:respawn:/sbin/getty -L ttyUSB0 115200 vt100
2. Plug in USB-serial converter cable
3. Wait for a login prompt on a terminal program attached to the serial
cable
4. Login
5. Pull the USB-serial converter cable from the box
6. getty doesn't realise that ttyUSB0 no longer exists as /dev/ttyUSB0
can still be opened.
7. Re-insert the USB-serial converter cable
8. You should no longer get a login prompt over the serial cable, as
the the USB-serial cable now shows up as /dev/ttyUSB1, and getty is
trying to talk to /dev/ttyUSB0.
The attached patch will cause open("/dev/ttyUSB0", O_RDONLY) to return
ENODEV after the USB-serial converter has been pulled. The patch was
created against 2.6.28.1. I can supply it against something else if
needs be. It is fairly simple, so should be OK.
I am using a pl2303 device, although I don't think that makes any
difference.
From: James Woodcock <James.Woodcock@ACULAB.COM>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This removes the fallback to the generic method. It is cleaner to
explicitely request it. Introducing this was my mistake. This will
be solved by an explicit test and the driver being allowed to request
what it needs to be done upon resumption.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
338b67b0c1 removed the info macro and
replaced its uses with dev_info. This patch does so for
usb-skeleton.c, which was missed.
Signed-off-by: Matt Kraai <kraai@ftbfs.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Make lines about usb_storage depending on SCSI visible when configuring the
kernel in a 80x25 console
Signed-off-by: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This lets userspace determine what the state of the RTS line is, which
is what is needed to properly handle data flow for this device (it
raises RTS when there is data to be sent from it.)
Cc: Kees Stoop <kees.stoop@opticon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
NOP transceiver is used by all the usb transceiver which are mostly
autonomous and doesn't require any programming or which are built
into the usb ip itself.NOP transceiver only allocates the memory
for struct xceiv and calls otg_set_transceiver() so function call
to otg_get_transceiver() will return a valid transceiver.
NOP transceiver device should be registered by calling
usb_nop_xceiv_register() from platform files.
Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com>
Cc: Felipe Balbi <felipe.balbi@nokia.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Remove some pointless messages from the FTDI serial driver;
I found these filling up syslog on one system. Also remove
a pointless "break" after a "return" in the same area.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
According to kerneljanitors todo list all printk calls (beginning
a new line) should have an according KERN_* constant.
Those are the missing peaces here for the usb subsystem.
Signed-off-by: Frank Seidel <frank@f-seidel.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch makes use of the generic method if a serial driver provides
no implementation. This simplifies implementing suspend/resume support
in serial drivers.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This exports a symbol for usb_serial_generic_resume, so that modules can
use it.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This removes an unnecessary check for autoresume from the generic
resume method. The check has been obsoleted by the now delayed
increase of the usage counter which makes the error this check prevented
impossible. This change allows drivers which only use the bulk read URB
the use of the generic method even if they support autosuspend.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch introduces a flag into the usb serial layer to tell drivers
that their URBs are killed due to suspension. That is necessary to let
drivers know whether they should report an error back.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Hi Greg,
this is for 2.6.30. Patches to use this in drivers are under development.
Regards
Oliver
With a postfix decrement count will reach -1 rather than 0,
so the warning will not be issued.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
this does the standard support for suspend/resume for the opticon
driver.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch implements suspend and resume methods for the
option driver. With my hardware I can even suspend the system
and keep up a connection for a short time.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-Off-By: Matthias Urlichs <smurf@smurf.noris.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Workaround of hw bug in IMX UDC.
This bug causes wrong handling of CFG_CHG interrupt.
Workaround is documented inline source code.
Signed-off-by: Darius Augulis <augulis.darius@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fix small bugs and add some omptimization in IMX UDC Gadget.
Signed-off-by: Darius Augulis <augulis.darius@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fixup of Werner Cornelius patch to the ch341 USB-serial driver, which adds:
- support all baudrates, not just a hard-coded set
- support for controlling DTR, RTS and CTS
Features still missing:
- character length other than 8 bits
- parity settings
- break control
I adapted his patch for the new usb_serial API introduced in 2.6.25-git8 by
Alan Cox on 22 July 2008. Non-compliance to the new API was a reason for
refusing a similar patch from Tollef Fog Heen.
Usage example by Tollef Fog Heen :
TEMPer USB thermometer <http://err.no/src/TEMPer.c>
Signed-off-by: Werner Cornelius <Werner.Cornelius@cornelius-consult.de>
Signed-off-by: Boris Hajduk <boris@hajduk.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This set of patches introduces calls to the following set of functions:
usb_endpoint_dir_in(epd)
usb_endpoint_dir_out(epd)
usb_endpoint_is_bulk_in(epd)
usb_endpoint_is_bulk_out(epd)
usb_endpoint_is_int_in(epd)
usb_endpoint_is_int_out(epd)
usb_endpoint_num(epd)
usb_endpoint_type(epd)
usb_endpoint_xfer_bulk(epd)
usb_endpoint_xfer_control(epd)
usb_endpoint_xfer_int(epd)
usb_endpoint_xfer_isoc(epd)
In some cases, introducing one of these functions is not possible, and it
just replaces an explicit integer value by one of the following constants:
USB_ENDPOINT_XFER_BULK
USB_ENDPOINT_XFER_CONTROL
USB_ENDPOINT_XFER_INT
USB_ENDPOINT_XFER_ISOC
An extract of the semantic patch that makes these changes is as follows:
(http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@r1@ struct usb_endpoint_descriptor *epd; @@
- ((epd->bmAttributes & \(USB_ENDPOINT_XFERTYPE_MASK\|3\)) ==
- \(USB_ENDPOINT_XFER_CONTROL\|0\))
+ usb_endpoint_xfer_control(epd)
@r5@ struct usb_endpoint_descriptor *epd; @@
- ((epd->bEndpointAddress & \(USB_ENDPOINT_DIR_MASK\|0x80\)) ==
- \(USB_DIR_IN\|0x80\))
+ usb_endpoint_dir_in(epd)
@inc@
@@
#include <linux/usb.h>
@depends on !inc && (r1||r5)@
@@
+ #include <linux/usb.h>
#include <linux/usb/...>
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
priv is checked not to be NULL near the beginning of the function and not
changed subsequently, making the test redundant.
A simplified version of the semantic patch that makes this change is as
follows: (http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@r exists@
local idexpression x;
expression E;
position p1,p2;
@@
if (x@p1 == NULL || ...) { ... when forall
return ...; }
... when != \(x=E\|x--\|x++\|--x\|++x\|x-=E\|x+=E\|x|=E\|x&=E\|&x\)
(
x@p2 == NULL
|
x@p2 != NULL
)
// another path to the test that is not through p1?
@s exists@
local idexpression r.x;
position r.p1,r.p2;
@@
... when != x@p1
(
x@p2 == NULL
|
x@p2 != NULL
)
@fix depends on !s@
position r.p1,r.p2;
expression x,E;
statement S1,S2;
@@
(
- if ((x@p2 != NULL) || ...)
S1
|
- if ((x@p2 == NULL) && ...) S1
|
- BUG_ON(x@p2 == NULL);
)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add the vbus_draw() callback to inform the transceiver, if
it exists, how much current may be drawn. The decision is
taken on gadget driver side using the configuration chosen
by the host and its bMaxPower field. Some systems can use
the host's VBUS supply to augment or recharge a battery.
(There's also a default of 100 mA for unconfigured devices,
or 8 mA if they're OTG devices.)
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When a transceiver driver is used, no automatic udc enable
is done. The transceiver (OTG or not) should :
- take care of VBus sensing
- call usb_gadget_vbus_connect()
- call usb_gadget_vbus_disconnect()
The pullup should remain within this driver's management,
either by gpio_pullup of udc_command() fields.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
On vbus_session() call, optionally activate D+ pullup
resistor and enable the udc, or deactivate D+ pullup
resistor and disable the udc.
It is intentional to not handle any VBus sense related irq.
An external transceiver driver (like gpio_vbus) should
catch VBus sense signal, and call usb_gadget_vbus_connect()
or usb_gadget_vbus_disconnect().
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Prepare pxa27x_udc to handle usb D+ pullup properly : it
should connect the pullup resistor and disconnect it only
if no external transceiver is handling it.
[ dbrownell@users.sourceforge.net: kerneldoc and gpio fixes ]
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Call usb_gadget_vbus_connect() and ...disconnect() from a
workqueue rather than from an irq handler, allowing msleep()
calls in vbus_session. Update kerneldoc to match.
[ dbrownell@users.sourceforge.net: more kerneldoc updates ]
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The usblp in 2.6.18 polled for status regardless if we actually needed it.
At some point I dropped it, to save the batteries if nothing else.
As it turned out, printers exist (e.g. Canon BJC-3000) that need prodding
this way or else they stop. This patch restores the old behaviour.
If you want to save battery, don't leave jobs in the print queue.
I tested this on my printers by printing and examining usbmon traces
to make sure status is being requested and printers continue to print.
Tuomas Jäntti verified the fix on BJC-3000.
Signed-off-by: Pete Zaitcev <zaitcev@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1203) increases the max_sector limit for USB tape
drives. By default usb-storage sets max_sectors to 240 (i.e., 120 KB)
for all devices. But tape drives need a higher limit, since tapes can
and do have very large block sizes. Without the ability to transfer
an entire large block in a single command, such tapes can't be used.
This fixes Bugzilla #12207.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-and-tested-by: Phil Mitchell <philipm@sybase.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Restore some code that was wrongly dropped from the RNDIS
driver, and caused interop problems observed with OpenMoko.
The issue is with hardware which needs help conforming to part
of the USB 2.0 spec (section 8.5.3.2); some can automagically
send a ZLP in response to an unexpected IN, but not all chips
will do that. We don't need to check the packet length ourselves
the way earlier code did, since the UDC must already check it.
But we do need to tell the UDC when it must force a short packet
termination of the data stage.
(Based on a patch from Aric D. Blumer <aric at sdgsystems.com>)
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Apparently the Configuration and Interface strings aren't used as
often as the Vendor, Product, and Serial strings. In at least one
device (a Saitek Cyborg Gold 3D joystick), attempts to read the
Configuration string cause the device to stop responding to Control
requests.
This patch (as1226) adds a quirks flag, telling the kernel not to
read a device's Configuration or Interface strings, together with a
new quirk for the offending joystick.
Reported-by: Melchior FRANZ <melchior.franz@gmail.com>
Tested-by: Melchior FRANZ <melchior.franz@gmail.com>
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@kernel.org> [2.6.28 and 2.6.29, nothing earlier]
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
dev_get_stats() handles all issues with net_device_ops
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
The "c-enter" USB to Toshiba 1.8" IDE enclosure needs special treatment
to work flawlessly. This patch is absolutely trivial, as the integrated
USB-IDE bridge is already identified to be an "unusual" device, only the
bcdDevice is different (lower) to the bcdDeviceMin already included in
the kernel.
It is a Prolific 2507 bridge.
T: Bus=02 Lev=01 Prnt=01 Port=02 Cnt=01 Dev#= 4 Spd=480 MxCh= 0
D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
P: Vendor=067b ProdID=2507 Rev= 0.01
S: Manufacturer=Prolific Technology Inc.
S: Product=ATAPI-6 Bridge Controller
S: SerialNumber=00000272
C:* #Ifs= 1 Cfg#= 1 Atr=c0 MxPwr=100mA
I:* If#= 0 Alt= 0 #EPs= 2 Cls=08(stor.) Sub=06 Prot=50 Driver=usb-storage
E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
Signed-off-by: Thomas Bartosik <tbartdev@gmx-topmail.de>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Option GTM380 in Modem mode uses Product ID 0x7201. This has been tested and works
on production systems for over 6 months.
Signed-off-by: Achilleas Kotsis <akots@exponent.gr>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* newer versions of the Novatel Wireless U727 CDMA 3G USB stick
have a different Product ID (0x5010); adding this ID makes them
work just fine with the option driver
Signed-off-by: Dirk Hohndel <hohndel@infradead.org>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Current firmware revision 5.60 still behaves the same,
so update the quirk up a (non-existing) 99.99 revision.
http://bugs.debian.org/cgi-bin/bugreport.cgi?bug=493415
Signed-off-by: Moritz Muehlenhoff <jmm@debian.org>
Tested-by: Jan Heitkoetter <devnull@heitkoetter.net>
Cc: stable <stable@kernel.org>
Signed-off-by: Phil Dibowitz <phil@ipom.com>
The generic cdc-acm driver is now the best one to handle Sony Ericsson
F3507g-based devices (which the Dell 5530 is a rebrand of), now that all
the pieces are in place (ie, cac477e8f1).
Removing the IDs from option allows cdc-acm to handle the device.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1225) fixes a bug in ehci-hcd. The condition for
whether unlinked QHs can become IDLE should not be that the controller
is halted, but rather that the controller isn't running. In other
words when the root hub is suspended, the hardware doesn't own any
QHs.
This fixes a problem that can show up during hibernation: If a QH is
only partially unlinked when the root hub is frozen, then when the
root hub is thawed the QH won't be in the IDLE state. As a result it
can't be used properly for new URB submissions.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: Brandon Philips <brandon@ifup.org>
Tested-by: Brandon Philips <brandon@ifup.org>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
ehci-hcd uses usb_get_urb() and usb_put_urb() in an unbalanced way causing
isochronous URB's kref.counts incrementing once per usb_submit_urb() call.
The culprit is *usb being set to NULL when usb_put_urb() is called after URB
is given back.
Due to other fixes there is no need for ehci-hcd to deal with usb_get_urb()
nor usb_put_urb() anymore, so patch removes their usages in ehci-hcd.
Patch also makes ehci_to_hcd(ehci)->self.bandwidth_allocated adjust, if a
stream finishes.
Signed-off-by: Karsten Wiese <fzu@wemgehoertderstaat.de>
Cc: David Brownell <david-b@pacbell.net>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Please consider this small patch for the usb option-card driver.
This patch adds the ZTE 622 usb modem device.
Signed-off-by: Albert Pauw <albert.pauw@gmail.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Make sure we don't leak locked vstdev->lock in vstusb_write. Unlock
properly on one fail path.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
There is an omitted unlock in mdc800_usb_probe's fail path. Add it.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Cc: Henning Zabel <henning@uni-paderborn.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
We do not hold mutex in one place in cxacru_cm, but unlock it on fail path.
Fix this.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Cc: Simon Arlott <cxacru@fire.lp0.eu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The usbfs driver manages a list of completed asynchronous URBs. But
it is too eager to free the entries on this list: destroy_async() gets
called whenever an interface is unbound or a device is removed, and it
deallocates the outstanding struct async entries for all URBs on that
interface or device. This is wrong; the user program should be able
to reap an URB any time after it has completed, regardless of whether
or not the interface is still bound or the device is still present.
This patch (as1222) moves the code for deallocating the completed list
entries from destroy_async() to usbdev_release(). The outstanding
entries won't be freed until the user program has closed the device
file, thereby eliminating any possibility that the remaining URBs
might still be reaped.
This fixes a bug in which a program can hang in the USBDEVFS_REAPURB
ioctl when the device is unplugged.
Reported-and-tested-by: Martin Poupe <martin.poupe@upek.com>
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The driver already supports the 1 protocol support, so just add it to
the MODULE_DEVICE_TABLE entry so it properly picks up these devices.
Thanks to Jouni Rynö for pointing this out.
Reported-by: Jouni Ryno <Jouni.Ryno@fmi.fi>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
open() will never succeed, as we always return -ENODEV. Fix this
obvious bug.
Thanks to Jouni Ryno for reporting it.
Reported-by: Jouni Ryno <Jouni.Ryno@fmi.fi>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Traditionally, changes to struct file->f_flags have been done under BKL
protection, or with no protection at all. This patch causes all f_flags
changes after file open/creation time to be done under protection of
f_lock. This allows the removal of some BKL usage and fixes a number of
longstanding (if microscopic) races.
Reviewed-by: Christoph Hellwig <hch@lst.de>
Cc: Al Viro <viro@ZenIV.linux.org.uk>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
The SUGGEST_* flags in the SCSI command result have been out of fashion
for a while and we don't actually use them in the error handling.
Remove the remaining occurrences.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
The SRP sysfs attribute is dependent on gadget mode; any
gadget may support SRP. But "rmmod musb_hdrc" didn't
remove that attribute; fix.
Signed-off-by: Vikram Pandita <vikram.pandita@ti.com>
Acked-by: Felipe Balbi <me@felipebalbi.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
If this is not done, khubd will not be informed of the disconnect
and will assume the device is still there.
Easily seen when a hub is connected with no device attached to it;
it will autosuspend. When the hub is disconnected, it still shows
up in /proc/bus/usb/devices
Signed-off-by: Anand Gadiyar <gadiyar@ti.com>
Acked-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Remove wrongly applied upper limit on the interrupt transfer
interval for low speed devices (not much of an error per se,
according to USB specs).
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Feeding 32-bit length cast down to 'u16' to min() to calculate the FIFO
count in musb_host_tx() risks sending a short packet prematurely for
transfer sizes over 64 KB.
Similarly, although data transfer size shouldn't exceed 65535 bytes for
the control endpoint, making musb_h_ep0_continue() more robust WRT URBs
with possibly oversized buffer will not hurt either...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
For some strange reason the host side musb_giveback() decides
that it's always got an IN transfer when the hardware endpoint
is using a shared FIFO. This causes musb_save_toggle() to read
the toggle state from the RXCSR register instead of TXCSR, and
may also cause unneeded reloading of RX endpoint registers.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The musb_h_disable() routine can oops in some cases:
- It's not safe to read hep->hcpriv outside musb->lock,
since it gets changed on completion IRQ paths.
- The list iterators aren't safe to use in that way;
just remove the first element while !list_empty(),
so deletions on other code paths can't make trouble.
We need two "scrub the list" loops because only one branch
should touch hardware and advance the schedule.
[ dbrownell@users.sourceforge.net: massively simplify
patch description; add key points as code comments ]
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The urb_dequeue() method forgets to unlink 'struct musb_qh' from the
control or bulk schedules when the URB being cancelled is the only
one queued to its endpoint. That will cause musb_advance_schedule()
to block once it reaches 'struct musb_qh' with now empty URB list, so
URBs queued for other endpoints after the one being dequeued will not
be served.
Fix by unlinking the QH from the list except when it's already being
handled (typically by musb_giveback). Since a QH with an empty URB
list is now supposed to be freed, do that. And remove a now-useless
check from musb_advance_schedule().
[ dbrownell@users.sourceforge.net: update patch description,
and fold in a dequeue() comment patch ]
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The input queue should be used for TX on endpoints which
share FIFO hardware. The host TX path wasn't doing that.
Shared FIFOs are most often configured for periodic endpoints,
which are mostly used for RX/IN transfers ... that's probably
how this bug managed to linger for a long time.
[ dbrownell@users.sourceforge.net: update patch description ]
Signed-off-by: Dmitry Krivoschekov <dkrivoschekov@ru.mvista.com>
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
request->actual is an unsigned and we should use the same
variable type for fifo_count otherwise we might lose some
data if request->length >= 64kbytes.
[ dbrownell@users.sourceforge.net: fix compiler warning ]
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Now that the musb build fixes for DaVinci got merged (RC3?), kick in
the other bits needed to get it finally *working* in mainline:
- Use clk_enable()/clk_disable() ... the "always enable USB clocks"
code this originally relied on has since been removed.
- Initialize the USB device only after the relevant I2C GPIOs are
available, so the host side can properly enable VBUS.
- Tweak init sequencing to cope with mainline's relatively late init
of the I2C system bus for power switches, transceivers, and so on.
Sanity tested on DM6664 EVM for host and peripheral modes; that system
won't boot with CONFIG_PM enabled, so OTG can't yet be tested. Also
verified on OMAP3.
(Unrelated: correct the MODULE_PARM_DESC spelling of musb_debug.)
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Felipe Balbi <me@felipebalbi.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1218) fixes a problem with a radio-control joystick used
in the "walkera 4#3" helicopter. This device responds to the initial
Get-String-Descriptor request for string 0 (which is really the list
of supported languages) by sending its config descriptor! The
usb_get_string() routine needs to check whether it got the right
type of descriptor.
Oddly enough, this sort of check is already present in
usb_get_descriptor(). The patch changes the error code from -EPROTO
to -ENODATA, because -EPROTO shows up in so many other contexts to
indicate a hardware failure rather than a firmware error.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Tested-by: Guillermo Jarabo <williamjap@gmail.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
===================================================================
In apollon case, it only used udc, so udc configuration should select
USB_OTG_UTILS also.
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1220) automatically disables stalls when g_file_storage
finds itself running with an Atmel device controller, because the
Atmel hardware/driver isn't capable of halting bulk endpoints
correctly.
Reported-by: Stanislaw Gruszka <stf_xl@wp.pl>
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1219) adds the IGNORE_RESIDUE flag to the unusual_devs
entries for Genesys Logic's USB-IDE adapter. Although this device
usually gets the residue correct, there is one command crucial to the
operation of CD and DVD drives which it messes up.
Tested-by: Mike Lampard <mike@mtgambier.net>
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
I noticed that my revision of the F3507G WWAN card isn't listed in
drivers/usb/serial/option.c
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The Motorola MOTOMAGX phones (Z6, E8, Zn5 so far) are providing
combined ACM/BLAN USB configuration. Since it has Vendor Specific
class, the corresponding drivers (cdc-acm, zaurus) can't find it just
by interface info. This patch adds usb id so the cdc-acm driver can
properly handle this combined device.
Signed-off-by: Dmitriy Taychenachev <dimichxp@gmail.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch addes the BenQ 3g modem support to the option driver.
From: Jesse Sung <jsung@novell.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
We where selecting wrong ep descriptors causing
some troubles while sending files over obex interface.
The problem was a typo while usb_find_endpoint() was being
called for HS endpoints.
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Currently ITDs are immediately recycled whenever their URB completes.
However, EHCI hardware can sometimes remember some ITD state. This
means that when the ITD is reused before end-of-frame it may sometimes
cause the hardware to reference bogus state.
This patch defers reusing such ITDs by moving them into a new ehci member
cached_itd_list. ITDs resting in cached_itd_list are moved back into their
stream's free_list once scan_periodic() detects that the active frame has
elapsed.
This makes the snd_usb_us122l driver (in kernel since .28) work right
when it's hooked up through EHCI.
[ dbrownell@users.sourceforge.net: comment fixups ]
Signed-off-by: Karsten Wiese <fzu@wemgehoertderstaat.de>
Tested-by: Philippe Carriere <philippe-f.carriere@wanadoo.fr>
Tested-by: Federico Briata <federicobriata@gmail.com>
Cc: stable <stable@kernel.org>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Clear next TD field and status field in queue head initialization code
to prevent unpredictable result caused by residue of usb reset.
Signed-off-by: Li Yang <leoli@freescale.com>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Remove the unneeded #include <mach/hardware.h>
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
*ep->reg_udccs is always set to 0.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Acked-by: Eric Miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
If a USB PCI controller is behind a cardbus bridge, we are trying to
restore its configuration registers too early, before the cardbus
bridge is operational. To fix this, call pci_restore_state() from
usb_hcd_pci_resume() and remove usb_hcd_pci_resume_early() which is
no longer necessary (the configuration spaces of USB controllers that
are not behind cardbus bridges will be restored by the PCI PM core
with interrupts disabled anyway).
This patch fixes the regression from 2.6.28 tracked as
http://bugzilla.kernel.org/show_bug.cgi?id=12659
[ Side note: the proper long-term fix is probably to just force the
unplug event at suspend time instead of doing a plug/unplug at resume
time, but this patch is fine regardless - Linus ]
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Reported-by: Miles Lane <miles.lane@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Use cpu_to_le32 directly as it handles constant folding now, replace direct
uses of __constant_cpu_to_{endian} as well.
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This device suffers from the off-by-one error when reporting the capacity,
so add US_FL_FIX_CAPACITY to the existing entry.
Signed-off-by: Nick Holloway <Nick.Holloway@pyrites.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
- New Novatel and Dell mobile broadband modem products added
- Dell pid variables used in stead of numerical PIDs for known
products
Signed-off-by: Dirk De Schepper <ddeschepper@nvtl.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Matthias Urlichs <matthias@urlichs.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds device IDs and balances the counts to make the
hot ID additioning mechanism work.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Cc: stable <stable@kernel.org>
Cc: Chris Adams <cmadams@hiwaay.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
There was one error path where unlock_kernel() wasn't called.
This was found with a code checker (http://repo.or.cz/w/smatch.git/)
Compile tested only, sorry.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1202) adds Pentax to usb-storage's list of bad vendors
whose devices always need the CAPACITY_HEURISTICS flag. This is in
addition to the existing entries: Nokia, Nikon, and Motorola.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Tested-by: Virgo Pärna <virgo.parna@mail.ee>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add support for the NDI Polaris system *http://www.ndigital.com/).
Cc: Ian Abbott <abbotti@mev.co.uk>
Cc: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The failure path of aircable_init is wrong, fix the order of (goto) labels.
Signed-off-by: Dave Young <hidave.darkstar@gmail.com>
Acked-by: Naranjo Manuel Francisco <naranjo.manuel@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1201) removes the WARN() from the last-sector hacks in
usb-storage, thereby making the code match the version now in
.27-stable and .28-stable. The WARN() isn't needed, since there is no
longer any intention of assuming that all storage devices have an even
number of sectors, and it annoys users for no good reason.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Revert 8b6346ec89 as these devices really
work just fine with the cdc-acm driver, as they follow the spec
properly.
Thanks to Chuck Ebbert for pointing out the problem here.
Cc: Chuck Ebbert <cebbert@redhat.com>
Cc: Dan Williams <dcbw@redhat.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The same patch to add support for MTK gps loggers was submitted by two
different people and applied twice. Remove the redundant lines.
Signed-off-by: James Treacy <treacy@debian.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
While disabling an endpoint the driver nuking any pending requests,
thus completing them with -ESHUTDOWN status. But the driver doesn't
clear the tx_req, which means that a next TX request (after
ep_enable), might get stalled, since the driver won't queue the new
reqests.
This patch fixes a bug I'm observing with ethernet gadget while
playing with ifconfig usb0 up/down (the up/down sequence disables
and enables `in' and `out' endpoints).
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Before freeing an endpoint's muram memory, we should stop all activity
of the endpoint, otherwise the QE UDC controller might do nasty things
with the muram memory that isn't belong to that endpoint anymore.
The qe_ep_reset() effectively flushes the hardware fifos, finishes all
late transaction and thus prevents the corruption.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Freescale QE UDC controllers can't report the "port change" states,
so the only way to handle disconnects is to process bus reset
interrupts. The bus reset can take some time, that is, few irqs.
Gadgets may print the disconnection events, and this causes few
repetitive messages in the kernel log.
This patch fixes the issue by using the usb_state machine, if the
usb controller has been already reset, just quit the reset irq
early.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
qe_udc_reg_init() leaves the USB controller enabled before muram memory
initialized. Sometimes the uninitialized muram memory confuses the
controller, and it start sending the busy interrupts.
Fix this by disabling the controller, it will be enabled later by
the gadget driver, at bind time.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The call chain is this:
qe_udc_irq() <- grabs the udc->lock spinlock
rx_irq()
qe_ep0_rx()
ep0_setup_handle()
setup_received_handle()
ch9getstatus()
qe_ep_queue() <- tries to grab the udc->lock again
It seems unsafe to temporarily drop the lock in the ch9getstatus(),
so to fix that bug the lock-less __qe_ep_queue() function
implemented and used by the ch9getstatus().
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
In case of probing errors the driver kfrees the udc_controller, but it
doesn't set the pointer to NULL.
When usb_gadget_register_driver is called, it checks for udc_controller
!= NULL, the check passes and the driver accesses nonexistent memory.
Fix this by setting udc_controller to NULL in case of errors.
While at it, also implement irq_of_parse_and_map()'s failure and cleanup
cases.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds support for the FHCI USB controller, as found
in the Freescale MPC836x and MPC832x processors. It can support
Full or Low speed modes.
Quite a lot the hardware is doing by itself (SOF generation, CRC
generation and checking), though scheduling and retransmission is on
software's shoulders.
This controller does not integrate the root hub, so this driver also
fakes one-port hub. External hub is required to support more than
one device.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds the support for the QUANTA Q101 series HSDPA Data Card.
With the vendor and product IDs are set properly,
the data card can be detected and works fine.
Signed-off-by: Alex Cheng <alex.cheng@quantatw.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Alan Stern
Greg Kroah-Hartman
Jouni Hogander
Pete Zaitcev
Ming Lei
David Brownell
Ajay Kumar Gupta
Giuseppe GORGOGLIONE
Sergei Shtylyov
Felipe Balbi
David Vrabel
Maciej Grela
Dave Young
Randy Dunlap
Harvey Harrison
Catalin Marinas
Boaz Harrosh
Thierry Vignaud
James Woodcock
Oliver Neukum
Matt Kraai
Borislav Petkov
Frank Seidel
Roel Kluin
Darius Augulis
Werner Cornelius
Huang Weiyi
Julia Lawall
Robert Jarzmik
Takashi Iwai
Stephen Hemminger
Thomas Bartosik
Achilleas Kotsis
Dirk Hohndel
Moritz Muehlenhoff
Dan Williams
Karsten Wiese
Albert Pauw
Jiri Slaby
Jan Dumon
Robert M. Kenney
Michael Hennerich
Axel Wachtler
Jonathan Corbet
Kuninori Morimoto
Russell King
Martin K. Petersen
David S. Miller
Vikram Pandita
Anand Gadiyar
Dmitry Krivoschekov
David Brownell
Adam Richter
Patrik Kullman
Dmitriy Taychenachev
Jesse Sung
Karsten Wiese
Li Yang
Hartley Sweeten
Linus Torvalds
Rafael J. Wysocki
Nick Holloway
Ivan Kuten
Dirk De Schepper
Dan Carpenter
Stephane Clerambault
James Treacy
Anton Vorontsov
Alex.Cheng@quantatw.com