Quoth David:
1) GRO MAC header comparisons were ethernet specific, breaking other
link types. This required a multi-faceted fix to cure the originally
noted case (Infiniband), because IPoIB was lying about it's actual
hard header length. Thanks to Eric Dumazet, Roland Dreier, and
others.
2) Fix build failure when INET_UDP_DIAG is built in and ipv6 is modular.
From Anisse Astier.
3) Off by ones and other bug fixes in netprio_cgroup from Neil Horman.
4) ipv4 TCP reset generation needs to respect any network interface
binding from the socket, otherwise route lookups might give a
different result than all the other segments received. From Shawn
Lu.
5) Fix unintended regression in ipv4 proxy ARP responses, from Thomas
Graf.
6) Fix SKB under-allocation bug in sh_eth, from Yoshihiro Shimoda.
7) Revert skge PCI mapping changes that are causing crashes for some
folks, from Stephen Hemminger.
8) IPV4 route lookups fill in the wildcarded fields of the given flow
lookup key passed in, which is fine most of the time as this is
exactly what the caller's want. However there are a few cases that
want to retain the original flow key values afterwards, so handle
those cases properly. Fix from Julian Anastasov.
9) IGB/IXGBE VF lookup bug fixes from Greg Rose.
10) Properly null terminate filename passed to ethtool flash device
method, from Ben Hutchings.
11) S3 resume fix in via-velocity from David Lv.
12) Fix double SKB free during xmit failure in CAIF, from Dmitry
Tarnyagin.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (72 commits)
net: Don't proxy arp respond if iif == rt->dst.dev if private VLAN is disabled
ipv4: Fix wrong order of ip_rt_get_source() and update iph->daddr.
netprio_cgroup: fix wrong memory access when NETPRIO_CGROUP=m
netprio_cgroup: don't allocate prio table when a device is registered
netprio_cgroup: fix an off-by-one bug
bna: fix error handling of bnad_get_flash_partition_by_offset()
isdn: type bug in isdn_net_header()
net: Make qdisc_skb_cb upper size bound explicit.
ixgbe: ethtool: stats user buffer overrun
ixgbe: dcb: up2tc mapping lost on disable/enable CEE DCB state
ixgbe: do not update real num queues when netdev is going away
ixgbe: Fix broken dependency on MAX_SKB_FRAGS being related to page size
ixgbe: Fix case of Tx Hang in PF with 32 VFs
ixgbe: fix vf lookup
igb: fix vf lookup
e1000: add dropped DMA receive enable back in for WoL
gro: more generic L2 header check
IPoIB: Stop lying about hard_header_len and use skb->cb to stash LL addresses
zd1211rw: firmware needs duration_id set to zero for non-pspoll frames
net: enable TC35815 for MIPS again
...
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
drm/i915: fixup interlaced bits clearing in PIPECONF on PCH_SPLIT (v2)
drm/i915: no lvds quirk for AOpen MP45
drm/i915: Force explicit bpp selection for intel_dp_link_required
drm/radeon: do not continue after error from r600_ib_test
drivers/gpu/drm/drm_ioc32.c: initialize all fields
drm/i915: fixup interlaced bits clearing in PIPECONF on PCH_SPLIT
drm/i915:: Disable FBC on SandyBridge
* 'drm-intel-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/keithp/linux:
drm/i915: fixup interlaced bits clearing in PIPECONF on PCH_SPLIT (v2)
drm/i915: no lvds quirk for AOpen MP45
drm/i915: Force explicit bpp selection for intel_dp_link_required
drm/i915: fixup interlaced bits clearing in PIPECONF on PCH_SPLIT
drm/i915:: Disable FBC on SandyBridge
Just a few new device ids, omap serial driver regression fixes, and a
build fix for the 8250 driver movement.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)
iEYEABECAAYFAk80KZgACgkQMUfUDdst+yk0HgCeIdU3VTWqdxZDXp3G1sFIXZ1b
47YAnRAMAar+/aLaNhqGrcz7aa5y2cUU
=8sr8
-----END PGP SIGNATURE-----
Merge tag 'tty-3.3-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Serial/TTY fixes for the 3.3-rc3 tree
Just a few new device ids, omap serial driver regression fixes, and a
build fix for the 8250 driver movement.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* tag 'tty-3.3-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
tty: serial: omap-serial: wakeup latency constraint is in microseconds, not milliseconds
tty: serial: OMAP: block idle while the UART is transferring data in PIO mode
tty: serial: OMAP: use a 1-byte RX FIFO threshold in PIO mode
m32r: relocate drivers back out of 8250 dir
tty: fix a build failure on sparc
serial: samsung: Add support for EXYNOS5250
serial: samsung: Add support for EXYNOS4212 and EXYNOS4412
drivers/tty/vt/vt_ioctl.c: fix KDFONTOP 32bit compatibility layer
Big things here is the deletion of the Android pmem driver, as it's
obsolete and no one uses it, the gma500 driver as it's already in the
drm portion of the kernel tree, and the pohmelfs filesystem as it's
obsolete and a rewritten version is being proposed for the fs/ section
of the kernel.
Other than that, a smattering of different bugfixes and regressions, and
some omap drm api merge fixups that were needed due to api changes in
the main portion of the drm tree, allowing this code to build properly
again.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)
iEYEABECAAYFAk80KLYACgkQMUfUDdst+ykhiwCg2ctSu4umygA1ErAedAA+sJkv
psYAn20OZQDyuBcBAIzL2L+Y/BUz8bXt
=xvyx
-----END PGP SIGNATURE-----
Merge tag 'staging-3.3-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Staging tree patches for 3.3-rc3
Big things here is the deletion of the Android pmem driver, as it's
obsolete and no one uses it, the gma500 driver as it's already in the
drm portion of the kernel tree, and the pohmelfs filesystem as it's
obsolete and a rewritten version is being proposed for the fs/ section
of the kernel.
Other than that, a smattering of different bugfixes and regressions, and
some omap drm api merge fixups that were needed due to api changes in
the main portion of the drm tree, allowing this code to build properly
again.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* tag 'staging-3.3-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging: (28 commits)
staging: pohmelfs: remove drivers/staging/pohmelfs
staging: android/ram_console: Don't build on arches w/o ioremap
staging: r8712u: Use asynchronous firmware loading
staging: usbip: fix to prevent potentially using uninitialized spinlock
staging: r8712u: Fix problem when CONFIG_R8712_AP is set
staging: tidspbridge: fix incorrect free to drv_datap
staging: tidspbridge: fix bridge_open memory leaks
staging: android: lowmemorykiller: Don't wait more than one second for a process to die
MAINTAINERS: staging: iio: add iio information
staging: zcache: fix serialization bug in zv stats
staging: fix go7007-usb license
Staging: android: binder: Fix crashes when sharing a binder file between processes
Staging: android: Remove pmem driver
Staging: asus_oled: fix NULL-ptr crash on unloading
Staging: asus_oled: fix image processing
Staging: android: binder: Don't call dump_stack in binder_vma_open
staging: r8712u: Add new Sitecom UsB ID
zcache: Set SWIZ_BITS to 8 to reduce tmem bucket lock contention.
zcache: fix deadlock condition
staging: drm/omap: fix locking issue
...
A few fixes for kobject warnings that have popped up in the cpu hotplug path,
and a regression fix for the speed of the hotplug memory code.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)
iEYEABECAAYFAk80J1cACgkQMUfUDdst+ylYfgCcClIeUw4njh3Tup9BpRrdBprr
fBsAoLKKhaZDsnma85PJRDAvtM2guoi7
=0TZ9
-----END PGP SIGNATURE-----
Merge tag 'driver-core-3.3-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Driver core fixes for the 3.3-rc3 tree.
A few fixes for kobject warnings that have popped up in the cpu hotplug path,
and a regression fix for the speed of the hotplug memory code.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* tag 'driver-core-3.3-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
driver-core: cpu: fix kobject warning when hotplugging a cpu
ACPI: remove duplicated lines of merging problems with acpi_processor_add
docbook: fix fatal errors in device-drivers docbook and add DMA Management section
drivers/base/memory.c: fix memory_dev_init() long delay
driver core: cpu: remove kernel warning when removing a cpu
Nothing big here, some Kconfig fixes for the MISC_DEVICES config option
that was being used incorrectly, and some other minor bug fixes.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)
iEYEABECAAYFAk80HSAACgkQMUfUDdst+ymFsQCghwKbV9B9z5fgUXYwFQJ/pD2j
GhsAn3J2mhhHN/vtSPQAN9Vu59Xb/tCi
=VZaE
-----END PGP SIGNATURE-----
Merge tag 'char-misc-3.3-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Minor char-misc fixes for 3.3-rc3
Nothing big here, some Kconfig fixes for the MISC_DEVICES config option
that was being used incorrectly, and some other minor bug fixes.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* tag 'char-misc-3.3-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
mmc: cb710 core: Add missing spin_lock_init for irq_lock of struct cb710_chip
cs5535-mfgpt: don't call __init function from __devinit
vmw_balloon: fix for a -Wuninitialized warning
drivers: misc: Remove MISC_DEVICES config option
c2port: fix build error for duramar2150 due to missing header.
Here are a few minor USB fixes and a bunch of device id updates for the
USB drivers.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)
iEYEABECAAYFAk80Ki4ACgkQMUfUDdst+ymp3wCfUG2LtQOC2qpzpnl1bcivSA18
11gAn09DbcldfH4k12HyCr7PuBnjILQh
=vfEv
-----END PGP SIGNATURE-----
Merge tag 'usb-3.3-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
USB fixes for 3.3-rc3
Here are a few minor USB fixes and a bunch of device id updates for the
USB drivers.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* tag 'usb-3.3-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
USB: usbserial: add new PID number (0xa951) to the ftdi driver
usb: ch9.h: usb_endpoint_maxp() uses __le16_to_cpu()
usb: musb: fix a build error on mips
uwb & wusb & usb wireless controllers: fix kconfig error & build errors
usb: Skip PCI USB quirk handling for Netlogic XLP
powerpc/usb: fix issue of CPU halt when missing USB PHY clock
usb: otg: mv_otg: Add dependence
usb: host: Distinguish Kconfig text for Freescale controllers
USB: add new zte 3g-dongle's pid to option.c
usb: ch9.h: usb_endpoint_maxp() uses __le16_to_cpu()
USB: qcserial: don't enable autosuspend
USB: qcserial: add several new serial devices
usb: otg: mv_otg: Add dependence
usb: gadget: zero: fix bug in loopback autoresume handling
The current error handling doesn't work because we flash_part is a u32
so the checks for negative error codes don't work. I considered making
things signed but I don't know the hardware enough to say if that's a
problem. Really, we don't use the error codes so just returning zero
for all problems is fine.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We use len to store the return value from eth_header(). eth_header()
can return -ETH_HLEN (-14). We want to pass this back instead of
truncating it to 65522 and returning that.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Treat pwmX as a measured value, not as a (mostly static) limit value, so
that it is updated more frequently from the device register.
Signed-off-by: Nikolaus Schulz <mail@microschulz.de>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
The receive FIFO wakeup latency estimate in the omap-serial driver is
three orders of magnitude too small. This effectively prevents the
MPU from going to a low-power state when CONFIG_CPU_IDLE=y. This is a
major power management regression and masks some other FIFO-related
bugs in the driver.
Fix by correcting the most egregious problem in the RX wakeup latency
estimate. There are several other flaws in the estimator; these will
be fixed by a separate patch series intended for 3.4.
The difference in low-power states with this patch can be observed via
debugfs in pm_debug/count.
This estimate does not have any effect when CONFIG_CPU_IDLE=n.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Alan Cox <alan@linux.intel.com>
Acked-by: Govindraj.R <govindraj.raja@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Tested-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Prevent OMAP UARTs from going idle while they are still transferring
data in PIO mode. This works around an oversight in the OMAP UART
hardware present in OMAP34xx and earlier: an idle UART won't send a
wakeup when the TX FIFO threshold is reached. This causes long delays
during data transmission when the MPU powerdomain enters a low-power
mode. The MPU interrupt controller is not able to respond to
interrupts when it's in a low-power state, so the TX buffer is not
refilled until another wakeup event occurs.
This fix changes the erratum i291 DMA idle workaround. Rather than
toggling between force-idle and no-idle, it will toggle between
smart-idle and no-idle. The important part of the workaround is the
no-idle part, so this shouldn't result in any change in behavior.
This fix should work on all OMAP UARTs. Future patches intended for
the 3.4 merge window will make this workaround conditional on a
"feature" flag, and will use the OMAP36xx+ TX event wakeup support.
Thanks to Kevin Hilman <khilman@ti.com> for mentioning the erratum i291
workaround, which led to the development of this approach.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Alan Cox <alan@linux.intel.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Govindraj.R <govindraj.raja@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Tested-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In the (default) PIO mode, use a one-byte RX FIFO threshold. The OMAP
UART IP blocks do not appear to be capable of waking the system under
an RX timeout condition. Since the previous RX FIFO threshold was 16
bytes, this meant that omap-serial.c did not become aware of any
received data until all those bytes arrived or until another UART
interrupt occurred. This made the serial console and presumably other
serial applications (GPS, serial Bluetooth) unusable or extremely
slow. A 1-byte RX FIFO threshold also allows the MPU to enter a
low-power consumption state while waiting for the FIFO to fill.
This can be verified using the serial console by comparing the
behavior when "0123456789abcde" is pasted in from another window, with
the behavior when "0123456789abcdef" is pasted in. Since the former
string is less than sixteen bytes long, the string is not echoed for
some time, while the latter string is echoed immediately.
DMA operation is unaffected by this patch.
Thanks to Russell King - ARM Linux <linux@arm.linux.org.uk> for some
additional information on the standard behavior of the RX timeout
event, which was used to improve this commit description.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Govindraj Raja <govindraj.r@ti.com>
Cc: Alan Cox <alan@linux.intel.com>
Cc: Russell King <linux@arm.linux.org.uk>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Tested-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the number of tx/rx queues changes the ethtool ioctl
ETHTOOL_GSTATS may overrun the userspace buffer. This
occurs because the general practice in user space to
query stats is to issue a ETHTOOL_GSSET cmd to learn the
buffer size needed, allocate the buffer, then call
ETHTOOL_GSTIRNGS and ETHTOOL_GSTATS. If the number of
real_num_queues is changed or flow control attributes
are changed after ETHTOOL_GSSET but before the
ETHTOOL_GSTRINGS/ETHTOOL_GSTATS a user space buffer
overrun occurs.
To fix the overrun always return the max buffer size
needed from get_sset_count() then return all strings
and stats from get_strings()/get_ethtool_stats().
This _will_ change the output from the ioctl() call
which could break applications and script parsing in
theory. I believe these changes should not break existing
tools because the only changes will be more {tx|rx}_queues
and the {tx|rx}_pb_* stats will always be returned.
Existing scripts already need to handle changing number
of queues because this occurs today depending on system
and current features. The {tx|rx}_pb_* stats are at the
end of the output and should be handled by scripts today
regardless.
Finally get_ethtool_stats and get_strings are free-form
outputs tools parsing these outputs should be defensive
anyways. In the end these updates are better then
having a tool segfault because of a buffer overrun.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Users expect the up2tc mapping to be maintained across a DCB
enable/disable/enable transition. And since we maintain all
the other DCB attributes we should do this for up2tc mappings
as well just to be consistent. Also without this we break
user space applications that expect this to occur that
previously worked.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Tested-by: Stephen Ko <stephen.s.ko@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
If the netdev is already in NETREG_UNREGISTERING/_UNREGISTERED state, do not
update the real num tx queues. netdev_queue_update_kobjects() is already
called via remove_queue_kobjects() at NETREG_UNREGISTERING time. So, when
upper layer driver, e.g., FCoE protocol stack is monitoring the netdev
event of NETDEV_UNREGISTER and calls back to LLD ndo_fcoe_disable() to remove
extra queues allocated for FCoE, the associated txq sysfs kobjects are already
removed, and trying to update the real num queues would cause something like
below:
...
PID: 25138 TASK: ffff88021e64c440 CPU: 3 COMMAND: "kworker/3:3"
#0 [ffff88021f007760] machine_kexec at ffffffff810226d9
#1 [ffff88021f0077d0] crash_kexec at ffffffff81089d2d
#2 [ffff88021f0078a0] oops_end at ffffffff813bca78
#3 [ffff88021f0078d0] no_context at ffffffff81029e72
#4 [ffff88021f007920] __bad_area_nosemaphore at ffffffff8102a155
#5 [ffff88021f0079f0] bad_area_nosemaphore at ffffffff8102a23e
#6 [ffff88021f007a00] do_page_fault at ffffffff813bf32e
#7 [ffff88021f007b10] page_fault at ffffffff813bc045
[exception RIP: sysfs_find_dirent+17]
RIP: ffffffff81178611 RSP: ffff88021f007bc0 RFLAGS: 00010246
RAX: ffff88021e64c440 RBX: ffffffff8156cc63 RCX: 0000000000000004
RDX: ffffffff8156cc63 RSI: 0000000000000000 RDI: 0000000000000000
RBP: ffff88021f007be0 R8: 0000000000000004 R9: 0000000000000008
R10: ffffffff816fed00 R11: 0000000000000004 R12: 0000000000000000
R13: ffffffff8156cc63 R14: 0000000000000000 R15: ffff8802222a0000
ORIG_RAX: ffffffffffffffff CS: 0010 SS: 0018
#8 [ffff88021f007be8] sysfs_get_dirent at ffffffff81178c07
#9 [ffff88021f007c18] sysfs_remove_group at ffffffff8117ac27
#10 [ffff88021f007c48] netdev_queue_update_kobjects at ffffffff813178f9
#11 [ffff88021f007c88] netif_set_real_num_tx_queues at ffffffff81303e38
#12 [ffff88021f007cc8] ixgbe_set_num_queues at ffffffffa0249763 [ixgbe]
#13 [ffff88021f007cf8] ixgbe_init_interrupt_scheme at ffffffffa024ea89 [ixgbe]
#14 [ffff88021f007d48] ixgbe_fcoe_disable at ffffffffa0267113 [ixgbe]
#15 [ffff88021f007d68] vlan_dev_fcoe_disable at ffffffffa014fef5 [8021q]
#16 [ffff88021f007d78] fcoe_interface_cleanup at ffffffffa02b7dfd [fcoe]
#17 [ffff88021f007df8] fcoe_destroy_work at ffffffffa02b7f08 [fcoe]
#18 [ffff88021f007e18] process_one_work at ffffffff8105d7ca
#19 [ffff88021f007e68] worker_thread at ffffffff81060513
#20 [ffff88021f007ee8] kthread at ffffffff810648b6
#21 [ffff88021f007f48] kernel_thread_helper at ffffffff813c40f4
Signed-off-by: Yi Zou <yi.zou@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Tested-by: Stephen Ko <stephen.s.ko@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch fixes an issue in which RSC will generate corrupted frames when
PAGE_SIZE is larger than 8K. Specifically it looks like that in 2.6.39 a
change was made so that GRO would always have at least 16 frags available
for coalescing, but the ixgbe RSC logic was not updated. As such the RSC
feature would generate a frame larger than 64K and then overflow the value
in the IP length field.
To correct that I am now basing things on the PAGE_SIZE.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Stephen Ko <stephen.s.ko@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
A check for the number of VFs allocated should have used a greater than
equal operator instead of just greater than. This caused allocation of
exactly 32 VFs to not enable the PF transmit and receive enables.
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Tested-by: Robert E Garrett <robertX.e.garrett@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Recent addition of code to find already allocated VFs failed to take
account that systems with 2 or more multi-port SR-IOV capable controllers
might have already enabled VFs. Make sure that the VFs the function is
finding are actually subordinate to the particular instance of the adapter
that is looking for them and not subordinate to some device that has
previously enabled SR-IOV.
This bug exists in 3.2 stable as well as 3.3 release candidates.
CC: stable@vger.kernel.org
Reported-by: David Ahern <daahern@cisco.com>
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Tested-by: Robert E Garrett <robertX.e.garrett@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Recent addition of code to find already allocated VFs failed to take
account that systems with 2 or more multi-port SR-IOV capable controllers
might have already enabled VFs. Make sure that the VFs the function is
finding are actually subordinate to the particular instance of the adapter
that is looking for them and not subordinate to some device that has
previously enabled SR-IOV.
This is applicable to 3.2+ kernels.
CC: stable@vger.kernel.org
Reported-by: David Ahern <daahern@cisco.com>
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Tested-by: Robert E Garrett <robertX.e.garrett@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Commit d5bc77a223 broke Wake-on-LAN by
inadvertently dropping the enabling of DMA receives.
Restore the enabling of DMA receives for WoL.
This is applicable to 3.1+ stable trees.
CC: stable@vger.stable.org
Reported-by: Tobias Klausmann <klausman@schwarzvogel.de>
Signed-off-by: Dean Nelson <dnelson@redhat.com>
Tested-by: Tobias Klausmann <klausman@schwarzvogel.de>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In order to extract the high byte of the 16-bit word, shift the word to
the right, not to the left.
Signed-off-by: Nikolaus Schulz <mail@microschulz.de>
Cc: stable@kernel.org # 2.6.32+
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Unlike the other chips supported by this driver, the F75387 stores the
pwm_mode in register F75375_REG_FAN_TIMER, not F75375_REG_CONFIG1.
Signed-off-by: Nikolaus Schulz <mail@microschulz.de>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
In order to enable temperature mode aka automatic mode for the F75373 and
F75375 chips, the two FANx_MODE bits in the fan configuration register
need be set to 01, not 10.
Signed-off-by: Nikolaus Schulz <mail@microschulz.de>
Cc: stable@kernel.org # 2.6.32+
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Commit ec3e5a1644 slipped in some duplicate code.
Remove it.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Acked-by: Jean Delvare <khali@linux-fr.org>
One patch fixes an bug in the ARM/MSM IOMMU code which returned sucess
in the unmap function even when an error occured and the other patch
adds a workaround into the AMD IOMMU driver to better handle broken IVRS
ACPI tables (this patch fixes the case when a device is not listed in
the table but actually translated by the iommu).
* 'iommu/fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu:
iommu/msm: Fix error handling in msm_iommu_unmap()
iommu/amd: Work around broken IVRS tables
This series contains pending target bug-fixes and cleanups for v3.3-rc3
that have been addressed the past weeks in lio-core.git.
Some of the highlights include:
- Fix handling for control CDBs with data greater than PAGE_SIZE (andy)
- Use IP_FREEBIND for iscsi-target to address network portal creation
issues with systemd (dax)
- Allow PERSISTENT RESERVE IN for non-reservation holder (marco)
- Fix iblock se_dev_attrib.unmap_granularity (marco)
- Fix unsupported WRITE_SAME sense payload handling (martin)
- Add workaround for zero-length control CDB handling (nab)
- Fix discovery with INADDR_ANY and IN6ADDR_ANY_INIT (nab)
- Fix target_submit_cmd() exception handling (nab)
- Return correct ASC for unimplemented VPD pages (roland)
- Don't zero pages used for data buffers (roland)
- Fix return code of core_tpg_.*_lun (sebastian)
* '3.3-rc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending: (26 commits)
target: Fix unsupported WRITE_SAME sense payload
iscsi: use IP_FREEBIND socket option
iblock: fix handling of large requests
target: handle empty string writes in sysfs
iscsi_target: in_aton needs linux/inet.h
target: Fix iblock se_dev_attrib.unmap_granularity
target: Fix target_submit_cmd() exception handling
target: Change target_submit_cmd() to return void
target: accept REQUEST_SENSE with 18bytes
target: Fail INQUIRY commands with EVPD==0 but PAGE CODE!=0
target: Return correct ASC for unimplemented VPD pages
iscsi-target: Fix discovery with INADDR_ANY and IN6ADDR_ANY_INIT
target: Allow control CDBs with data > 1 page
iscsi-target: Fix up a few assignments
iscsi-target: make one-bit bitfields unsigned
iscsi-target: Fix double list_add with iscsit_alloc_buffs reject
iscsi-target: Fix reject release handling in iscsit_free_cmd()
target: fix return code of core_tpg_.*_lun
target: use save/restore lock primitive in core_dec_lacl_count()
target: avoid multiple outputs in scsi_dump_inquiry()
...
1/ two small fixes to ensure we handle an interrupted resync properly.
2/ avoid loading the bitmap multiple times in dm-raid
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)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=k0Xz
-----END PGP SIGNATURE-----
Merge tag 'md-3.3-fixes' of git://neil.brown.name/md
Some simple md-related fixes.
1/ two small fixes to ensure we handle an interrupted resync properly.
2/ avoid loading the bitmap multiple times in dm-raid
* tag 'md-3.3-fixes' of git://neil.brown.name/md:
md: two small fixes to handling interrupt resync.
Prevent DM RAID from loading bitmap twice.
Minor SPI device driver changes. A rename of the pch_spi_pcidev symbol
that merely eliminates a modpost warning, and a Kconfig change to allow
the Samsung spi driver to build on EXYNOS.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=0yQc
-----END PGP SIGNATURE-----
Merge tag 'spi-for-linus' of git://git.secretlab.ca/git/linux-2.6
SPI bug fixes for v3.3-rc2
Minor SPI device driver changes. A rename of the pch_spi_pcidev symbol
that merely eliminates a modpost warning, and a Kconfig change to allow
the Samsung spi driver to build on EXYNOS.
* tag 'spi-for-linus' of git://git.secretlab.ca/git/linux-2.6:
spi-topcliff-pch: rename pch_spi_pcidev to pch_spi_pcidev_driver
spi: Add spi-s3c64xx driver dependency on ARCH_EXYNOS4
This fixes a memory-corrupting bug: not only does it cause the warning,
but as a result of dropping the refcount to zero, it causes the
pcmcia_socket0 device structure to be freed while it still has
references, causing slab caches corruption. A fatal oops quickly
follows this warning - often even just a 'dmesg' following the warning
causes the kernel to oops.
While testing suspend/resume on an ARM device with PCMCIA support, and a
CF card inserted, I found that after five suspend and resumes, the
kernel would complain, and shortly die after with slab corruption.
WARNING: at include/linux/kref.h:41 kobject_get+0x28/0x50()
As the message doesn't give a clue about which kobject, and the built-in
debugging in drivers/base/power/main.c happens too late, this was added
right before each get_device():
printk("%s: %p [%s] %u\n", __func__, dev, kobject_name(&dev->kobj), atomic_read(&dev->kobj.kref.refcount));
and on the 3rd s2ram cycle, the following behaviour observed:
On the 3rd suspend/resume cycle:
dpm_prepare: c1a0d998 [pcmcia_socket0] 3
dpm_suspend: c1a0d998 [pcmcia_socket0] 3
dpm_suspend_noirq: c1a0d998 [pcmcia_socket0] 3
dpm_resume_noirq: c1a0d998 [pcmcia_socket0] 3
dpm_resume: c1a0d998 [pcmcia_socket0] 3
dpm_complete: c1a0d998 [pcmcia_socket0] 2
4th:
dpm_prepare: c1a0d998 [pcmcia_socket0] 2
dpm_suspend: c1a0d998 [pcmcia_socket0] 2
dpm_suspend_noirq: c1a0d998 [pcmcia_socket0] 2
dpm_resume_noirq: c1a0d998 [pcmcia_socket0] 2
dpm_resume: c1a0d998 [pcmcia_socket0] 2
dpm_complete: c1a0d998 [pcmcia_socket0] 1
5th:
dpm_prepare: c1a0d998 [pcmcia_socket0] 1
dpm_suspend: c1a0d998 [pcmcia_socket0] 1
dpm_suspend_noirq: c1a0d998 [pcmcia_socket0] 1
dpm_resume_noirq: c1a0d998 [pcmcia_socket0] 1
dpm_resume: c1a0d998 [pcmcia_socket0] 1
dpm_complete: c1a0d998 [pcmcia_socket0] 0
------------[ cut here ]------------
WARNING: at include/linux/kref.h:41 kobject_get+0x28/0x50()
Modules linked in: ucb1x00_core
Backtrace:
[<c0212090>] (dump_backtrace+0x0/0x110) from [<c04799dc>] (dump_stack+0x18/0x1c)
[<c04799c4>] (dump_stack+0x0/0x1c) from [<c021cba0>] (warn_slowpath_common+0x50/0x68)
[<c021cb50>] (warn_slowpath_common+0x0/0x68) from [<c021cbdc>] (warn_slowpath_null+0x24/0x28)
[<c021cbb8>] (warn_slowpath_null+0x0/0x28) from [<c0335374>] (kobject_get+0x28/0x50)
[<c033534c>] (kobject_get+0x0/0x50) from [<c03804f4>] (get_device+0x1c/0x24)
[<c0388c90>] (dpm_complete+0x0/0x1a0) from [<c0389cc0>] (dpm_resume_end+0x1c/0x20)
...
Looking at commit 7b24e79882 ("pcmcia: split up central event handler"),
the following change was made to cs.c:
return 0;
}
#endif
-
- send_event(skt, CS_EVENT_PM_RESUME, CS_EVENT_PRI_LOW);
+ if (!(skt->state & SOCKET_CARDBUS) && (skt->callback))
+ skt->callback->early_resume(skt);
return 0;
}
And the corresponding change in ds.c is from:
-static int ds_event(struct pcmcia_socket *skt, event_t event, int priority)
-{
- struct pcmcia_socket *s = pcmcia_get_socket(skt);
...
- switch (event) {
...
- case CS_EVENT_PM_RESUME:
- if (verify_cis_cache(skt) != 0) {
- dev_dbg(&skt->dev, "cis mismatch - different card\n");
- /* first, remove the card */
- ds_event(skt, CS_EVENT_CARD_REMOVAL, CS_EVENT_PRI_HIGH);
- mutex_lock(&s->ops_mutex);
- destroy_cis_cache(skt);
- kfree(skt->fake_cis);
- skt->fake_cis = NULL;
- s->functions = 0;
- mutex_unlock(&s->ops_mutex);
- /* now, add the new card */
- ds_event(skt, CS_EVENT_CARD_INSERTION,
- CS_EVENT_PRI_LOW);
- }
- break;
...
- }
- pcmcia_put_socket(s);
- return 0;
-} /* ds_event */
to:
+static int pcmcia_bus_early_resume(struct pcmcia_socket *skt)
+{
+ if (!verify_cis_cache(skt)) {
+ pcmcia_put_socket(skt);
+ return 0;
+ }
+ dev_dbg(&skt->dev, "cis mismatch - different card\n");
+ /* first, remove the card */
+ pcmcia_bus_remove(skt);
+ mutex_lock(&skt->ops_mutex);
+ destroy_cis_cache(skt);
+ kfree(skt->fake_cis);
+ skt->fake_cis = NULL;
+ skt->functions = 0;
+ mutex_unlock(&skt->ops_mutex);
+ /* now, add the new card */
+ pcmcia_bus_add(skt);
+ return 0;
+}
As can be seen, the original function called pcmcia_get_socket() and
pcmcia_put_socket() around the guts, whereas the replacement code
calls pcmcia_put_socket() only in one path. This creates an imbalance
in the refcounting.
Testing with pcmcia_put_socket() put removed shows that the bug is gone:
dpm_suspend: c1a10998 [pcmcia_socket0] 5
dpm_suspend_noirq: c1a10998 [pcmcia_socket0] 5
dpm_resume_noirq: c1a10998 [pcmcia_socket0] 5
dpm_resume: c1a10998 [pcmcia_socket0] 5
dpm_complete: c1a10998 [pcmcia_socket0] 5
Tested-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Cc: Dominik Brodowski <linux@dominikbrodowski.net>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In current code, pltfm->als_vmin is set to LM3530_ALS_WINDOW_mV and
pltfm->als_vmax is 0. This does not make sense. I think what we want
here is setting pltfm->als_vmax to LM3530_ALS_WINDOW_mV.
Both als_vmin and als_vmax local variables will be set to
pltfm->als_vmin and pltfm->als_vmax by a few lines latter. Thus also
remove a redundant assignment for als_vmin and als_vmax in this patch.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Cc: Shreshtha Kumar Sahu <shreshthakumar.sahu@stericsson.com>
Acked-by: Milo(Woogyom) Kim <milo.kim@ti.com>
Tested-by: Milo(Woogyom) Kim <milo.kim@ti.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
New pohmelfs is coming, and it is time to remove deadly old design
https://lkml.org/lkml/2012/2/8/293
Signed-off-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit a0417fa3a1 ("net: Make qdisc_skb_cb upper size bound
explicit.") made it possible for a netdev driver to use skb->cb
between its header_ops.create method and its .ndo_start_xmit
method. Use this in ipoib_hard_header() to stash away the LL address
(GID + QPN), instead of the "ipoib_pseudoheader" hack. This allows
IPoIB to stop lying about its hard_header_len, which will let us fix
the L2 check for GRO.
Signed-off-by: Roland Dreier <roland@purestorage.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Due to the sysdev conversion to struct device, the cpu objects get
reused when adding a cpu after offlining it, which causes a big warning
that the kobject portion is not properly initialized.
So clear out the object before we register it again, so all is quiet.
Reported-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Tested-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Those lines have two copies.
Not sure how it could happen, looks like git problem.
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Thomas Renninger <trenn@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 9bef3d4197
"serial: group all the 8250 related code together"
inadvertently swept up the m32r driver in the move, because
it had comments mentioning 8250 registers within it. However
these are only there by nature of the driver being based off
the 8250 source code -- the hardware itself does not actually
have any relation to the original 8250 style UARTs.
Reported-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fixes UML build:
CC drivers/staging/android/ram_console.o
drivers/staging/android/ram_console.c: In function
'ram_console_driver_probe':
drivers/staging/android/ram_console.c:358:2: error: implicit declaration
of function 'ioremap' [-Werror=implicit-function-declaration]
cc1: some warnings being treated as errors
make[3]: *** [drivers/staging/android/ram_console.o] Error 1
Signed-off-by: Anton Vorontsov <anton.vorontsov@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In https://bugs.archlinux.org/task/27996, failure of driver r8712u is
reported, with a timeout during module loading due to synchronous loading
of the firmware. The code now uses request_firmware_nowait().
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The stub_probe function can be called as soon as the stub_driver is
registered. This can lead to the busid_table_lock being used before it
is initialized. Moved calling the init_busid_table function (which
initalizes this spinlock) to be called earlier in the init function to
prevent this from happening.
Signed-off-by: Bart Westgeest <bart@elbrys.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When this driver was upgraded to the vendor 20100831 version in
commit 93c55dda09 et al,, one listhead initialization was missed.
This broke complete operation of the driver whenever AP mode was
enabled.
This patch fixes https://bugs.archlinux.org/task/27996.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@vger.stable.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This structure is still used after it has been freed, since it
is being allocated in probe, calls to free it have been moved to
module's remove routine.
This should fix the follwoing messages when attempting to remove the
module:
drv_get_first_dev_extension: Failed to retrieve the object handle
drv_get_first_dev_extension: Failed to retrieve the object handle
drv_destroy: Failed to store DRV object
mgr_destroy: Failed to store MGR object
Signed-off-by: Omar Ramirez Luna <omar.ramirez@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There are two members of pr_ctxt allocated during bridge_open that
are never freed resulting in memory leaks, these are stream_id and
node_id, they are now freed on release of the handle (bridge_release)
right before freeing pr_ctxt.
Error path for bridge_open was also fixed since the same variables
could result in memory leaking due to missing handling of failure
scenarios. While at it, the indentation changes were introduced to
avoid interleaved goto statements inside big if blocks.
Signed-off-by: Omar Ramirez Luna <omar.ramirez@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If a process forked and the child process was killed by the
lowmemorykiller, the lowmemory killer would be disabled until
the parent process reaped the child or it died itself.
Signed-off-by: Arve Hjønnevåg <arve@android.com>
Signed-off-by: Anton Vorontsov <anton.vorontsov@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In a multithreaded workload, the zv_curr_dist_counts
and zv_cumul_dist_counts statistics are being corrupted
because the increments and decrements in zv_create
and zv_free are not atomic.
This patch converts these statistics and their corresponding
increments/decrements/reads to atomic operations.
Signed-off-by: Seth Jennings <sjenning@linux.vnet.ibm.com>
Acked-by: Dan Magenheimer <dan.magenheimer@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add MODULE_LICENSE() for this source module to fix build warning:
WARNING: modpost: missing MODULE_LICENSE() in drivers/staging/media/go7007/go7007-usb.o
see include/linux/module.h for more information
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Cc: Ross Cohen <rcohen@snurgle.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Opening the binder driver and sharing the file returned with
other processes (e.g. by calling fork) can crash the kernel.
Prevent these crashes with the following changes:
- Add a mutex to protect against two processes mmapping the
same binder_proc.
- After locking mmap_sem, check that the vma we want to access
(still) points to the same mm_struct.
- Use proc->tsk instead of current to get the files struct since
this is where we get the rlimit from.
Signed-off-by: Arve Hjønnevåg <arve@android.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Addroid pmem driver is no longer used in any of the Android products.
This patch removes pmem driver from Android staging area
Reference: https://lkml.org/lkml/2012/1/23/183
Signed-off-by: Shuah Khan <shuahkhan@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Programming an image was broken, because odev->buf_offs was not advanced
for val == 0 in append_values(). This regression was introduced in:
commit 1ff12a4aa3
Author: Kevin A. Granade <kevin.granade@gmail.com>
Date: Sat Sep 5 01:03:39 2009 -0500
Staging: asus_oled: Cleaned up checkpatch issues.
Fix the image processing by special-casing val == 0.
I have tested this change on an Asus G50V laptop only.
Cc: Jakub Schmidtke <sjakub@gmail.com>
Cc: Kevin A. Granade <kevin.granade@gmail.com>
Signed-off-by: Pekka Paalanen <pq@iki.fi>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
If user-space partially unmaps the driver, binder_vma_open
would dump the kernel stack. This is not a kernel bug however
and will be treated as if the whole area was unmapped once
binder_vma_close gets called.
Signed-off-by: Arve Hjønnevåg <arve@android.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
SWIZ_BITS > 8 results in a much larger number of "tmem_obj"
allocations, likely one per page-placed-in-frontswap. The
tmem_obj is not huge (roughly 100 bytes), but it is large
enough to add a not-insignificant memory overhead to zcache.
The SWIZ_BITS=8 will get roughly the same lock contention
without the space wastage.
The effect of SWIZ_BITS can be thought of as "2^SWIZ_BITS is
the number of unique oids that be generated" (This concept is
limited to frontswap's use of tmem).
Acked-by: Seth Jennings <sjenning@linux.vnet.ibm.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
I discovered this deadlock condition awhile ago working on RAMster
but it affects zcache as well. The list spinlock must be
locked prior to the page spinlock and released after. As
a result, the page copy must also be done while the locks are held.
Applies to 3.2. Konrad, please push (via GregKH?)...
this is definitely a bug fix so need not be pushed during
a -rc0 window.
Signed-off-by: Dan Magenheimer <dan.magenheimer@oracle.com>
Acked-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The create/free mmap offset code must be synchronized. Yet only some
callers of omap_gem_mmap_offset() held struct_mutex. Leading to various
crashes around drm_mm_insert_helper_range(). (In the free-object path,
which is currently the only place we drm_gem_free_mmap_offset(),
struct_mutex is already held.)
Signed-off-by: Rob Clark <rob@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Move the free after the final uses.
The semantic patch that makes this report is available
in scripts/coccinelle/free/kfree.cocci.
More information about semantic patching is available at
http://coccinelle.lip6.fr/
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fix minimum width/height so planes could be used to implement
hw mouse cursor.
Signed-off-by: Rob Clark <rob@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add support in framebuffer objects for other color formats and multi-
planar YUV (NV12). Since this requires changing the API between the
plane and fb for getting scanout information (paddr, etc), take
advantage of the opportunity and put in place a way to allow fb's to
be unpinned when they are not being scanned out. Now, before start
of scanout the plane calls omap_framebuffer_pin() which takes care
to pin all the backing bo's, then omap_framebuffer_update_scanout()
however many times to update the scanout address(es), etc, and then
when finished omap_framebuffer_unpin().
Signed-off-by: Rob Clark <rob@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Because framebuffer layer and overlay scanout video pipes are basically
thing in OMAP display subsystem (the only difference being that the first
video pipe does not support scaling or YUV formats), much of the CRTC
code is pulled into the plane implementation, and a private plane object
is used by the CRTC object. This avoids code duplication between the
plane and CRTC.
Signed-off-by: Rob Clark <rob@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Update to reflect changes in:
"drm: add an fb creation ioctl that takes a pixel format v5"
Signed-off-by: Rob Clark <rob@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Update to reflect changes in:
"Make the per-driver file_operations struct const"
Signed-off-by: Rob Clark <rob@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
It's now "properly" merged into the DRM tree in the kernel, so delete
the staging version of the driver as it is far obsolete and broken.
Requested-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
An identical patch has been merged for i9xx_crtc_mode_set:
Commit 59df7b1771
Author: Christian Schmidt <schmidt@digadd.de>
Date: Mon Dec 19 20:03:33 2011 +0100
drm/intel: Fix initialization if startup happens in interlaced mode [v2]
But that one neglected to fix up the ironlake+ path.
This should fix the issue reported by Alfonso Fiore where booting with
only a HDMI cable connected to his TV failed to display anything. The
issue is that the bios set up things for 1080i and used the pannel
fitter to scale up the lower progressive resolutions. We failed to
clear the interlace bit in the PIPEACONF register, resulting in havoc.
v2: Be more paranoid and just unconditionally clear the field before
setting new values.
Cc: Peter Ross <pross@xvid.org>
Cc: Alfonso Fiore <alfonso.fiore@gmail.com>
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Keith Packard <keithp@keithp.com>
commit 8268f5a741 ("deny partial write for loop dev fd") tried to fix the
loop device partial read information leak problem. But it changed the
semantics of read behavior. When we read beyond the end of the device we
should get 0 bytes, which is normal behavior, we should not just return
-EIO
Instead of returning -EIO, zero out the bio to avoid information leak in
case of partail read.
Signed-off-by: Dave Young <dyoung@redhat.com>
Reviewed-by: Jeff Moyer <jmoyer@redhat.com>
Tested-by: Jeff Moyer <jmoyer@redhat.com>
Cc: Dmitry Monakhov <dmonakhov@sw.ru>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
floppy driver does not call add_disk() on all the drives hence we don't take
gendisk reference on request queue for these drives. Don't call put_disk()
with disk->queue set, otherwise we try to put the reference we never took.
Reported-and-tested-by: Dirk Gouders <gouders@et.bocholt.fh-gelsenkirchen.de>
Signed-off-by: Vivek Goyal<vgoyal@redhat.com>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
add_disk() takes gendisk reference on request queue. If driver failed during
initialization and never called add_disk() then that extra reference is not
taken. That reference is put in put_disk(). floppy driver allocates the
disk, allocates queue, sets disk->queue and then relizes that floppy
controller is not present. It tries to tear down everything and tries to
put a reference down in put_disk() which was never taken.
In such error cases cleanup disk->queue before calling put_disk() so that
we never try to put down a reference which was never taken in first place.
Reported-and-tested-by: Suresh Jayaraman <sjayaraman@suse.com>
Tested-by: Dirk Gouders <gouders@et.bocholt.fh-gelsenkirchen.de>
Signed-off-by: Vivek Goyal <vgoyal@redhat.com>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
The keeplocked variable in the cdrom driver is shared across multiple
drives, but set in per-device ioctls. Move it to the per-device struct,
avoiding that the setting on one drive affects the driver's behavior
when closing another.
[ Impact: limit udev's confusion to one drive when a CD burning program
unlocks the CD door at the end of burning. ]
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
According to a bug report, it doesn't have one.
Cc: stable@kernel.org
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=44263
Acked-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Keith Packard <keithp@keithp.com>
It includes:
- a compile fix for fsl-diu-fb
- a fix for a suspend/resume issue in atmel_lcdfb
- a fix for a suspend/resume issue in OMAP
- a workaround for a hardware bug to avoid physical damage in OMAP
- a really trivial dead code removal in intelfb
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.12 (GNU/Linux)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=2uP4
-----END PGP SIGNATURE-----
Merge tag 'fbdev-fixes-for-3.3-1' of git://github.com/schandinat/linux-2.6
fbdev fixes for 3.3
It includes:
- compile fix for fsl-diu-fb
- fix for a suspend/resume issue in atmel_lcdfb
- fix for a suspend/resume issue in OMAP
- workaround for a hardware bug to avoid physical damage in OMAP
- really trivial dead code removal in intelfb
* tag 'fbdev-fixes-for-3.3-1' of git://github.com/schandinat/linux-2.6:
atmel_lcdfb: fix usage of CONTRAST_CTR in suspend/resume
intelfb: remove some dead code
drivers/video: compile fixes for fsl-diu-fb.c
OMAPDSS: HDMI: PHY burnout fix
OMAP: 4430SDP/Panda: add HDMI HPD gpio
OMAP: 4430SDP/Panda: setup HDMI GPIO muxes
OMAPDSS: remove wrong HDMI HPD muxing
OMAP: 4430SDP/Panda: rename HPD GPIO to CT_CP_HPD
OMAP: 4430SDP/Panda: use gpio_free_array to free HDMI gpios
OMAPDSS: use sync versions of pm_runtime_put
Those lines have two copies.
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Cc: Thomas Renninger <trenn@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-2.6:
mfd: Avoid twl6040-codec PLL reconfiguration when not needed
mfd: Store twl6040-codec mclk configuration
Some devices (iwl5100) cannot connect to zd1211rw based AP. It appears that
zd1211 firmware messes up duration_id field if it is not set to zero by driver.
Sniffing traffic shows that zd1211 is transmitting frames with duration_id bits
14 and 15 set and other bits appearing random. Setting duration_id at driver to
zero results zd1211 outputting sane duration_id. This means that firmware is
setting correct values itself and expects duration_id to be zero in first
place.
Looking at vendor driver shows that only PSPoll frames have duration_id set by
driver, for other frames duration_id left zero.
Original bug-report and attached patch at:
http://sourceforge.net/mailarchive/message.php?msg_id=28759111
Reported-by: Tomas Vanek <Tomas.Vanek@fbl.cz>
[modified original patch from bug-report, added check for pspoll frame]
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
8<----------------------------------------------------------------------
From: Ralf Roesch <ralf.roesch@rw-gmbh.de>
Date: Wed, 16 Nov 2011 09:33:50 +0100
Subject: [PATCH] net: enable TC35815 for MIPS again
TX493[8,9] MIPS SoCs support 2 Ethernet channels of type TC35815
which are connected to the internal PCI controller.
And JMR3927 MIPS board has a TC35815 chip on board.
These dependencies were lost on movement to drivers/net/ethernet/toshiba.
Signed-off-by: Ralf Roesch <ralf.roesch@rw-gmbh.de>
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
CC: stable@vger.kernel.org [3.2+]
Signed-off-by: David S. Miller <davem@davemloft.net>
When this GETHER controller received a large frame (about 1800 bytes
or more), skb_over_panic() happened. This is because the previous
driver set the RFLR to 0x1000 (4096 bytes) and the skb allocate size
is smaller than 4096 bytes. So, the controller accepted such a frame.
The controller can discard a large frame by the RFLR setting.
So, the patch modifies the value of RFLR to mtu + ETH_HLEN +
VLAN_HLEN + ETH_FCS_LEN.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We allocate memory for 'new_data' with kmalloc(). If we get the memory
we then try to build_skb() and if that should fail (which it can) we
do not enter 'if (likely(skb)) {' and actually use 'new_data' but
instead fall through to the 'drop:' label and end up returning from
the function without ever assigning 'new'data' to anything or freeing
it. That leaks the memory allocated to 'new_data'.
This patch fixes the memory leak by doing a kfree(new_data) in the
case where build_skb() fails (or where allocation of 'new_data' itself
fails, but in taht case it's just a harmless kfree(NULL)).
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Acked-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As it is, with PCI/ISA/MCA/CCW all set to n and PCMCIA set to m
setting TR to y will set LLC to m, with very unpleasant results -
net/802/psnap gets picked into obj-y, resulting in the kernel
that won't link - psnap calls functions from llc. The cause,
AFAICS, is that kconfig gets rev_dep for LLC containing
|| TR && (deps for TR)
and even though TR is boolean, both LLC and PCMCIA are tristate
and that thing becomes || y && (n || m), i.e. || m. The reason
for dependency on PCMCIA is that when none of PCI, ISA, MCA, CCW
or PCMCIA is set there'll be no tokenring drivers, so there's no
point building tokenring core. Proper fix probably belongs in
kconfig (we need strict and, such that y <strict_and> m would be
y, so that rev_deps added for tristate selected by bool would
use that instead of &&; we'd have || TR <strict_and> (deps for TR)
in this case), but it's a rather intrusive change. There's an
easy workaround in case of TR -> LLC select, namely to have a def_bool y
symbol sitting under if TR and have that symbol selecting LLC.
Kudos to johill for suggesting that one...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
As reported by several people...
The code in rx_clean was panic'ing so revert
commit d0249e4443.
Will redo DMA mapping checks as new patches for a later release.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Analogically to d7cb3dbd1 ("HID: wacom: Fix invalid power_supply_powers
calls"), fix also the same occurence in wiimote driver.
Reported-by: przemo@firszt.eu
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Removed the following:
* irrelevant argument 'barrier' of mtip_hw_submit_io()
* unused member 'eh_active' of struct driver_data
Signed-off-by: Asai Thambi S P <asamymuthupa@micron.com>
Signed-off-by: Sam Bradshaw <sbradshaw@micron.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
This patch fixes a bug in target-core where unsupported WRITE_SAME ops
from a target_check_write_same_discard() failure was incorrectly
returning CHECK_CONDITION w/ TCM_INVALID_CDB_FIELD sense data.
This was causing some clients to not properly fall back, so go ahead
and use the correct TCM_UNSUPPORTED_SCSI_OPCODE sense for this case.
Reported-by: Martin Svec <martin.svec@zoner.cz>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Use IP_FREEBIND socket option so that iscsi portal configuration with
explicit IP addresses can happen during boot, before network interfaces
have been assigned IPs.
This is especially important on systemd based Linux boxes where system
boot happens asynchronously and non-trivial configuration must be done
to get targetcli.service to start synchronously after the network is
configured.
Reference:
http://lists.fedoraproject.org/pipermail/devel/2011-October/158025.html
Signed-off-by: Dax Kelson <dkelson@gurulabs.com>
Cc: "Nicholas A. Bellinger" <nab@linux-iscsi.org>
Cc: "Andy Grover" <agrover@redhat.com>
Cc: "Lennart Poettering" <lennart@poettering.net>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Requesting to many bvecs upsets bio_alloc_bioset, so limit the number we ask
for to the amount it can handle.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
These are root only and we're not likely to hit the problem in practise,
but it makes the static checkers happy.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Fixes this error after a recent nfs cleanup:
drivers/target/iscsi/iscsi_target_configfs.c: In function 'lio_target_call_addnptotpg':
drivers/target/iscsi/iscsi_target_configfs.c:214:3: error: implicit declaration of function 'in6_pton' [-Werror=implicit-function-declaration]
drivers/target/iscsi/iscsi_target_configfs.c:239:3: error: implicit declaration of function 'in_aton' [-Werror=implicit-function-declaration]
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
The block layer keeps q->limits.discard_granularity in bytes, but iblock
(and the SCSI Block Limits VPD page) keep unmap_granularity in blocks.
Report the correct value when exporting block devices by dividing to
convert bytes to blocks.
Signed-off-by: Roland Dreier <roland@purestorage.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch fixes a bug in target_submit_cmd() where the failure path
for transport_generic_allocate_tasks() made a direct call to
transport_send_check_condition_and_sense() and not calling the
final target_put_sess_cmd() release callback.
For transport_generic_allocate_tasks() failures, use the proper call to
transport_generic_request_failure() to handle kref_put() along
with potential internal queue full response processing.
It also makes transport_lookup_cmd_lun() failures in
target_submit_cmd() use transport_send_check_condition_and_sense() and
target_put_sess_cmd() directly to avoid se_cmd->se_dev reference in
transport_generic_request_failure() handling.
Finally it drops the out_check_cond: label and use direct reference for
allocate task failures, and per-se_device queue_full handling is
currently not supported for transport_lookup_cmd_lun() failure
descriptors due to se_device dependency.
Reported-by: Roland Dreier <roland@purestorage.com>
Cc: Roland Dreier <roland@purestorage.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Retval not very useful, and may even be harmful. Once submitted, fabrics
should expect a sense error if anything goes wrong. All fabrics checking
of this retval are useless or broken:
fc checks it just to emit more debug output.
ib_srpt trickles retval up, then it is ignored.
qla2xxx trickles it up, which then causes a bug because the abort goto
in qla_target.c thinks cmd hasn't been sent to target.
Just returning nothing is best.
Signed-off-by: Andy Grover <agrover@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
WindowsXP+BOT issues a MODE_SENSE request with page 0x1c which is not
suppoerted by target. Target rejects that command with
TCM_INVALID_CDB_FIELD, so far so good. On BOT I can't send the SENSE
response back, instead I can only reply that an error occured. The next
thing happens is a REQUEST_SENSE request with 18 bytes length. Since the
check here is more than 18 bytes I have to NACK that request as well.
This is not really required: We check for some additional room, but we
never use it. The additional length is set to 0xa so the total length is
0xa + 8 = 18 which is fine with my 18 bytes.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
1/ If a resync is aborted we should record how far we got
(recovery_cp) the last request that we know has completed
(->curr_resync_completed) rather than the last request that was
submitted (->curr_resync).
2/ When a resync aborts we still want to update the metadata with
any changes, so set MD_CHANGE_DEVS even if we 'skip'.
Signed-off-by: NeilBrown <neilb@suse.de>
Straight forward bug fixes in this branch. A couple of x86 gpio drivers
missing spinlock initialization, an API change fixup for the samsung driver
and a name typo fix.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=WQ/Y
-----END PGP SIGNATURE-----
Merge tag 'gpio-for-linus' of git://git.secretlab.ca/git/linux-2.6
GPIO fixes for v3.3-rc2
Straight forward bug fixes in this branch. A couple of x86 gpio drivers
missing spinlock initialization, an API change fixup for the samsung driver
and a name typo fix.
* tag 'gpio-for-linus' of git://git.secretlab.ca/git/linux-2.6:
gpio: Add missing spin_lock_init in gpio-ml-ioh driver
gpio: Add missing spin_lock_init in gpio-pch driver
gpio: samsung: adapt to changes in gpio specifier translator function declaration
Correct bad gpio naming
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.10 (GNU/Linux)
iQEcBAABAgAGBQJPLedwAAoJEANmWzN1g3l3F18IAJvV8cvTBDr/OV5wmEHx4v7t
s9l7wfXop2ilsNoAT8mdLwa6ilwatG9k9UhzsF8a2nUR1rNAWA9SFc2v6kLCIZpN
SVQzh9260X5jrRiUn7dKpLwwxDbepcvHFbpei9Xi/ON97ZjUnHEk27tf/s6MI8ad
EvCCJR+Lsw1ara6ZX+kQqznUME46dPZA6A5rxXFbRv8QTIe8++f+KSdXWBt8r3yK
pDfdEGyYwkDoqjUBv2EZ/XMCQdjmdgU9NRExKHJdOyHnea+0RbUik1viuXm7JNQV
Rd9DtC3vjq8qxCLBhJ1Ay5K8TmAbrgAGGjCo98mNY8D0F9NXL4sfyPW7qxCEa3E=
=tYxf
-----END PGP SIGNATURE-----
Merge tag 'hwmon-fixes-for-3.3-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging
One patch to fix fan detection on NCT6776F.
* tag 'hwmon-fixes-for-3.3-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
hwmon: (w83627ehf) Fix number of fans for NCT6776F
It is never correct to use intel_crtc->bpp in intel_dp_link_required,
so instead pass an explicit bpp in to this function. This patch
only supports 18bpp and 24bpp modes, which means that 10bpc modes will
be computed incorrectly. Fixing that will require more extensive
changes, and so must be addressed separately from this bugfix.
intel_dp_link_required is called from intel_dp_mode_valid and
intel_dp_mode_fixup.
* intel_dp_mode_valid is called to list supported modes; in this case,
the current crtc values cannot be relevant as the modes in question
may never be selected. Thus, using intel_crtc->bpp is never right.
* intel_dp_mode_fixup is called during mode setting, but it is run
well before ironlake_crtc_mode_set is called to set intel_crtc->bpp,
so using intel_crtc-bpp in this path can only ever get a stale
value.
Cc: Lubos Kolouch <lubos.kolouch@gmail.com>
Cc: Adam Jackson <ajax@redhat.com>
Cc: stable@vger.kernel.org
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=42263
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=44881
Tested-by: Dave Airlie <airlied@redhat.com>
Tested-by: camalot@picnicpark.org (Dell Latitude 6510)
Tested-by: Roland Dreier <roland@digitalvampire.org>
Signed-off-by: Keith Packard <keithp@keithp.com>
mlx4_en_prepare_rx_desc does not correctly clean up after it finds an
allocation failure. It should unmap a page before calling put_page, but
it only calls the later.
This bug would prevent a device removal using hotplug after setting the
device MTU to 9000 and opening the network interface. After the fix, we
still see the allocation failure with MTU 9000, but we are able to
remove the device.
Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After opening the network interface, Mellanox ConnectX device cannot be
removed by hotplug because it has not properly unmapped all DMA memory.
It happens that mlx4_en_activate_rx_rings overrides the variable that
keeps the size of the memory mapped.
This is fixed by passing to mlx4_en_destroy_rx_ring the same size that is
given to mlx4_en_create_rx_ring.
After applying this patch, hot unplugging the device works after opening
the interface.
Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The brcmsmac driver is now using the bcma SPROM CRC check, which does
not recognize all chipsets that were functional prior to the switch. In
particular, the current code bails out on odd CRC errors in recent
Macbooks. This patch ignores those errors, with the argument that an
unrecognized SPROM should be treated similarly to a non-existing one.
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use port number for correct steering (list per port).
Before the fix all steering entries (for both physical ports)
were managed in first port structures, so we had leakage of resources
for port 2.
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use MLX4_DEV_CAP_FLAG_VEP_UC_STEER for unicast_promisc_add/remove
Unicast entries were managed in wrong data structures.
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
Perform cleanup also in non-master flow.
The VFs use communication channel as well.
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit adb5066 "ath9k_hw: do not apply the 2.4 ghz ack timeout
workaround to cts" reduced the hardware CTS timeout to the normal
values specified by the standard, but it turns out while it doesn't
need the same extra time that it needs for the ACK timeout, it
does need more than the value specified in the standard, but only
for 2.4 GHz.
This patch brings the CTS timeout value in sync with the initialization
values, while still allowing adjustment for bigger distances.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Cc: stable@vger.kernel.org
Reported-by: Seth Forshee <seth.forshee@canonical.com>
Reported-by: Marek Lindner <lindner_marek@yahoo.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
commit b4a82a0 "ath9k_hw: fix interpretation of the rx KeyMiss flag"
fixed the interpretation of the KeyMiss flag for keycache based lookups,
however WEP encryption uses a static index, so KeyMiss is always asserted
for it, even though frames are decrypted properly.
Fix this by clearing the ATH9K_RXERR_KEYMISS flag if no keycache based
lookup was performed.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Cc: stable@vger.kernel.org
Reported-by: Laurent Bonnans <bonnans.l@gmail.com>
Reported-by: Jurica Vukadin <u.ra604@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If driver load is failed, sometimes few pointers may remain
uninitialized ex. priv->wdev, priv->netdev, adapter->sleep_cfm
This will cause NULL pointer dereferance while unloading the
driver.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kiran Divekar <dkiran@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
power_supply_powers calls added in 35b4c01e2 ("power_supply: add "powers" links
to self-powered HID devices") have to be called after power device is created.
This patch also fixes the second call - it has to be "ac" instead of "battery"
Signed-off-by: Przemo Firszt <przemo@firszt.eu>
Signed-off-by: Chris Bagwell <chris@cnpbagwell.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Sync with Linus' tree. This is necessary to have a base for
patch that fixes commit 35b4c01e29 ("power_supply: add "powers"
links to self-powered HID devices") which went in through Anton's
tree.
"nframes" comes from the user and "nframes * CD_FRAMESIZE_RAW" can wrap
on 32 bit systems. That would have been ok if we used the same wrapped
value for the copy, but we use a shifted value. We should just use the
checked version of copy_to_user() because it's not going to make a
difference to the speed.
Cc: stable@vger.kernel.com
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Rename static struct pci_driver pch_spi_pcidev to
pch_spi_pcidev_driver to get rid of warnings from modpost checks.
Signed-off-by: Danny Kukawka <danny.kukawka@bisect.de>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
The spi-s3c64xx driver is also used on Exynos4 so update the dependency
to enable build on those platforms.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
[grant.likely: relax depends to ARCH_EXYNOS instead of ARCH_EXYNOS4]
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Initially diagnosed on Ubuntu 11.04 with kernel 2.6.38.
velocity_close is not called during a suspend / resume cycle in this
driver and it has no business playing directly with power states.
Signed-off-by: David Lv <DavidLv@viatech.com.cn>
Acked-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
NCT6776F can select fan input pins for fans 3 to 5 with a secondary set of
chip register bits. Check that second set of bits in addition to the first set
to detect if fans 3..5 are monitored.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Cc: stable@vger.kernel.org # 3.0+
Acked-by: Jean Delvare <khali@linux-fr.org>
* A series of OMAP regression fixes for merge window fallout
* Two patches for Davinci, one removes some misdefined clocks, the other
is a regression fix for merge window fallout
* Two patches that makes Broadcom bcmring build again (and removes a
bunch of unused code in the process)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=tFsG
-----END PGP SIGNATURE-----
Merge tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
arm-soc fixes for 3.3-rc
* A series of OMAP regression fixes for merge window fallout
* Two patches for Davinci, one removes some misdefined clocks, the other
is a regression fix for merge window fallout
* Two patches that makes Broadcom bcmring build again (and removes a
bunch of unused code in the process)
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: bcmring: fix build failure in mach-bcmring/arch.c
ARM: bcmring: remove unused DMA map code
ARM: davinci: update mdio bus name
ARM: OMAP2+: arch/arm/mach-omap2/smartreflex.c: add missing iounmap
ARM: OMAP2+: arch/arm/mach-omap2/devices.c: introduce missing kfree
ARM: OMAP: fix MMC2 loopback clock handling
ARM: OMAP: fix erroneous mmc2 clock change on mmc3 setup
ARM: OMAP2+: GPMC: fix device size setup
ARM: OMAP2+: timer: Fix crash due to wrong arg to __omap_dm_timer_read_counter
ARM: OMAP3: hwmod data: register dss hwmods after dss_core
ARM: OMAP2/3: PRM: fix missing plat/irqs.h build breakage
ARM: OMAP2+: io: fix compilation breakage on 2420-only configs
ARM: OMAP4: hwmod data: Add names for DMIC memory address space
ARM: OMAP3: hwmod data: add SYSC_HAS_ENAWAKEUP for dispc
ARM: OMAP2+: hwmod data: split omap2/3 dispc hwmod class
ARM: davinci: DA850: remove non-existing pll1_sysclk4-7 clocks
ARM: OMAP2: fix regulator warnings
ARM: OMAP2: fix omap3 touchbook kconfig warning
i2c: OMAP: Fix OMAP1 build error
* 'fixes' of git://git.infradead.org/users/vkoul/slave-dma:
i.MX SDMA: Fix burstsize settings
ARM: mach-shmobile: both USB DMAC instances on sh7372 are slave-only
dma: sh_dma: not all SH DMAC implementations support MEMCPY
at_hdmac: bugfix for enabling channel irq
dmaengine: fix missing 'cnt' in ?: in dmatest
- Fix breakage with MTD suspend caused by the API rework
- Fix a problem with resetting the MX28 BCH module
- A couple of other trivial fixes
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iEYEABECAAYFAk8s6HsACgkQdwG7hYl686MIiACgxpNoUWFvq8z+2UGXxsLnNrio
hhcAn31H7TY3KUuIQBo4CqG2dEjNwpCw
=DRWp
-----END PGP SIGNATURE-----
Merge tag 'for-linus-3.3' of git://git.infradead.org/~dwmw2/mtd-3.3
- Fix a regression in 16-bit Atmel NAND flash which was introduced in 3.1
- Fix breakage with MTD suspend caused by the API rework
- Fix a problem with resetting the MX28 BCH module
- A couple of other trivial fixes
* tag 'for-linus-3.3-20120204' of git://git.infradead.org/~dwmw2/mtd-3.3:
Revert "mtd: atmel_nand: optimize read/write buffer functions"
mtd: fix MTD suspend
jffs2: do not initialize variable unnecessarily
mtd: gpmi-nand bugfix: reset the BCH module when it is not MX23
mtd: nand: fix typo in comment
This reverts commit fb5427508a.
The reason is that it breaks 16 bits NAND flash as it was reported by
Nikolaus Voss and confirmed by Eric Bénard.
Nicolas Ferre <nicolas.ferre@atmel.com> alco confirmed:
"After double checking with designers, I must admit that I misunderstood
the way of optimizing accesses to SMC. 16 bit nand is not so common
those days..."
Reported-by: Nikolaus Voss <n.voss@weinmann.de>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Cc: stable@kernel.org [3.1+]
KDFONTOP(GET) currently fails with EIO when being run in a 32bit userland
with a 64bit kernel if the font width is not 8.
This is because of the setting of the KD_FONT_FLAG_OLD flag, which makes
con_font_get return EIO in such case.
This flag should *not* be set for KDFONTOP, since it's actually the whole
point of this flag (see comment in con_font_set for instance).
Signed-off-by: Samuel Thibault <samuel.thibault@ens-lyon.org>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Cc: Greg Kroah-Hartman <gregkh@suse.de>
Cc: Arthur Taylor <art@ified.ca>
Cc: Jiri Slaby <jslaby@suse.cz>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
lkdtm_do_action() may call sleeping functions like kmalloc(), so do not
call it with spin lock held.
Signed-off-by: WANG Cong <xiyou.wangcong@gmail.com>
Cc: Prarit Bhargava <prarit@redhat.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Greg Kroah-Hartman <greg@kroah.com>
Reviewed-by: Dave Young <dyoung@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
On sparc, there is a build failure:
drivers/tty/serial/8250/8250.c:48:21: error: suncore.h: No such file or directory
drivers/tty/serial/8250/8250.c:3275: error: implicit declaration of function 'sunserial_register_minors'
drivers/tty/serial/8250/8250.c:3305: error: implicit declaration of function 'sunserial_unregister_minors'
this is due to commit 9bef3d4197
(serial: group all the 8250 related code together) moved these files
into 8250/ subdirectory, but forgot to change the reference
to drivers/tty/serial/suncore.h.
Cc: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: WANG Cong <xiyou.wangcong@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
all works need to be initialized before ieee80211_register_hw
to prevent mac80211 call backs such as drv_start, drv_config
getting started. otherwise we would queue/cancel works before
initializing them and it leads to kernel panic.
this issue can be recreated with the following script
in Chrome laptops with AR928X cards, with background scan
running (or) Network manager is running
while true
do
sudo modprobe -v ath9k
sleep 3
sudo modprobe -r ath9k
sleep 3
done
EIP: [<81040a47>] __cancel_work_timer+0xb8/0xe1 SS:ESP 0068:f6be9d70
---[ end trace 4f86d6139a9900ef ]---
Registered led device: ath9k-phy0
ieee80211 phy0: Atheros AR9280 Rev:2 mem=0xf88a0000,
irq=16
Kernel panic - not syncing: Fatal exception
Pid: 456, comm: wpa_supplicant Tainted: G D
3.0.13 #1
Call Trace:
[<81379e21>] panic+0x53/0x14a
[<81004a30>] oops_end+0x73/0x81
[<81004b53>] die+0x4c/0x55
[<81002710>] do_trap+0x7c/0x83
[<81002855>] ? do_bounds+0x58/0x58
[<810028cc>] do_invalid_op+0x77/0x81
[<81040a47>] ? __cancel_work_timer+0xb8/0xe1
[<810489ec>] ? sched_clock_cpu+0x81/0x11f
[<8103f809>] ? wait_on_work+0xe2/0xf7
[<8137f807>] error_code+0x67/0x6c
[<810300d8>] ? wait_consider_task+0x4ba/0x84c
[<81040a47>] ? __cancel_work_timer+0xb8/0xe1
[<810380c9>] ? try_to_del_timer_sync+0x5f/0x67
[<81040a91>] cancel_work_sync+0xf/0x11
[<f88d7b7c>] ath_set_channel+0x62/0x25c [ath9k]
[<f88d67d1>] ? ath9k_tx_last_beacon+0x26a/0x85c [ath9k]
[<f88d8899>] ath_radio_disable+0x3f1/0x68e [ath9k]
[<f90d0edb>] ieee80211_hw_config+0x111/0x116 [mac80211]
[<f90dd95c>] __ieee80211_recalc_idle+0x919/0xa37 [mac80211]
[<f90dda76>] __ieee80211_recalc_idle+0xa33/0xa37 [mac80211]
[<812dbed8>] __dev_open+0x82/0xab
Cc: <stable@vger.kernel.org>
Cc: Gary Morain <gmorain@google.com>
Cc: Paul Stewart <pstew@google.com>
Cc: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Tested-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently even if association is failed "iw link" shows some
information about connected BSS and "Tx timeout" error is seen in
dmesg log.
This patch fixes below issues in the code to handle assoc failure
case correctly.
1) "status" variable in mwifiex_wait_queue_complete() is not
correctly updated. Hence driver doesn't inform cfg80211 stack
about association failure.
2) During association network queues are stopped but carrier is
not cleared, which gives Tx timeout error in failure case
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Do not reconfigure the PLL in case it has been configured already
with the requested parameters.
In case of different PLL configuration do only the needed changes.
This can save considerable amount of time since we can avoid the
defined protocol (with delays) for the PLL configuration.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Store the last used mclk configuration for the PLL.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
transport_init_session() and target_fabric_configfs_init() don't
return NULL pointers, they only return ERR_PTRs or valid pointers.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Correct spelling "packtetbuf_num" to "packetbuf_num" in
drivers/net/ethernet/intel/ixgbe/ixgbe_common.h
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Change copyright date to 2012 in the source files.
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Robert E Garrett <robertX.e.garrett@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Tested-by: Robert E Garrett <robertX.e.garrett@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Remove jump to out label that was skipping over code to replace the
ack bit in the mailbox cache variable. This was causing driver mailbox
routines that poll for the PF to ack a message to time out which would
in turn cause all other mailbox messages to fail. Also replace the
mailbox cache variable message indication bit when a message is found
so that other functions that choose to poll for a mailbox message from
the PF won't miss it.
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Tested-by: Robert E Garrett <robertX.e.garrett@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Send message to system log when the VF requests another MAC filter
but there is no space left on the device for it.
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Tested-by: Robert E Garrett <robertX.e.garrett@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
New year so bump the copyright date.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This return statement got dropped while fixing the conflicts introduced
in 7a7e8734ac.
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The c32 structure is allocated on the stack and its idx field is not
initialized before copying it to user level. This patch takes the value
from the result of the ioctl, as done for the other fields.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Dave Airlie <airlied@redhat.com>
From 2d5a38a56453421e82428155f4b00303f3fb19b2 Mon Sep 17 00:00:00 2001
From: Igor Murzov <e-mail@date.by>
Date: Wed, 1 Feb 2012 03:11:53 +0400
Subject: [PATCH] Input: i8042 - add Lenovo Ideapad U455 to 'reset' blacklist
Lenovo Ideapad U455 needs to be in the reset quirk list for its
touchpad's proper function.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=40672
Signed-off-by: Igor Murzov <e-mail@date.by>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
On mips, we got:
drivers/usb/musb/musb_io.h:44: error: conflicting types for 'readsl'
arch/mips/include/asm/io.h:529: error: previous definition of 'readsl' was here
drivers/usb/musb/musb_io.h:46: error: conflicting types for 'readsw'
arch/mips/include/asm/io.h:528: error: previous definition of 'readsw' was here
drivers/usb/musb/musb_io.h:48: error: conflicting types for 'readsb'
so, should add !defined(CONFIG_MIPS) too.
Cc: Felipe Balbi <balbi@ti.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: WANG Cong <xiyou.wangcong@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix scan_timers() to be __devinit and not __init since
the function get called from cs5535_mfgpt_probe which is
__devinit.
Signed-off-by: Danny Kukawka <danny.kukawka@bisect.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix for a -Wuninitialized compiler warning. Changed return value of
vmballoon_send_lock_page() from bool to int to be able to distinguish
between the error cases to avoid uninitialized use of hv_status in
vmballoon_reserve_page()
Signed-off-by: Danny Kukawka <danny.kukawka@bisect.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This should be added for EXYNOS4212 and EXYNOS4412 SoCs.
Cc: Thomas Abraham <thomas.abraham@linaro.org>
Cc: Greg Kroah-Hartman <gregkh@suse.de>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
KDFONTOP(GET) currently fails with EIO when being run in a 32bit userland
with a 64bit kernel if the font width is not 8.
This is because the compatibility layer introduced by e9216651 ("tty:
handle VT specific compat ioctls in vt driver") forces the addition of the
KD_FONT_FLAG_OLD flag, which makes con_font_get return EIO in such case.
This flag should *not* be set for KDFONTOP, since it's actually the whole
point of this flag (see comment in con_font_set for instance).
Signed-off-by: Samuel Thibault <samuel.thibault@ens-lyon.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Arthur Taylor <art@ified.ca>
Cc: Jiri Slaby <jslaby@suse.cz>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph-client:
rbd: fix safety of rbd_put_client()
rbd: fix a memory leak in rbd_get_client()
ceph: create a new session lock to avoid lock inversion
ceph: fix length validation in parse_reply_info()
ceph: initialize client debugfs outside of monc->mutex
ceph: change "ceph.layout" xattr to be "ceph.file.layout"
Change the way channels objects are linked together by peak_pci_probe()
avoiding any kernel oops when driver is removed. Side effect is that
the list is now browsed from last to first channel.
Signed-off-by: Stephane Grosjean <s.grosjean@peak-system.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
netif_device_attched is called twice when ems_usb_start fails with -ENODEV
Signed-off-by: Sebastian Haas <dev@sebastianhaas.info>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The test (((errc & PCH_REC) >> 8) > 127) would always be false because
the receive error counter ((errc & PCH_REC) >> 8) is at most 127, where
PCH_REC is defined as 0x7f00. To test whether the receive error counter
has reached the error passive level, the RP bit (15) should be used.
Signed-off-by: Xi Wang <xi.wang@gmail.com>
Acked-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch fixes locking problems by using netif_rx() instead of
netif_receive_skb() in ti_hecc_error() called from the interrupt
context.
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This fix avoids a deadlock if an interrupt occurs
during consecutive port operations on ISA cards
utilising indirect access via address and data
port.
Tested on a B&R ISA card.
Cc: linux-can@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Wolfgang Zarre <lkdev@essax.com>
Acked-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
On slow systems and high CAN bitrates, the error message
"can_put_echo_skb: BUG! echo_skb is occupied!" did show up because
can_put_echo_skb() was called after starting the transfer.
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
As pointed out by Reuben Dowle and Lothar Waßmann, the TWRN_INT,
RWRN_INT, BOFF_INT interrupt sources need to be cleared as well
to avoid interrupt flooding, at least for the Flexcan on i.MX28
SOCs. Furthermore, the interrupts are only cleared, if really one
of those interrupt sources are pending (which is not the case for
rx and tx done).
Cc: Reuben Dowle <Reuben.Dowle@navico.com>
Cc: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The rbd_client structure uses a kref to arrange for cleaning up and
freeing an instance when its last reference is dropped. The cleanup
routine is rbd_client_release(), and one of the things it does is
delete the rbd_client from rbd_client_list. It acquires node_lock
to do so, but the way it is done is still not safe.
The problem is that when attempting to reuse an existing rbd_client,
the structure found might already be in the process of getting
destroyed and cleaned up.
Here's the scenario, with "CLIENT" representing an existing
rbd_client that's involved in the race:
Thread on CPU A | Thread on CPU B
--------------- | ---------------
rbd_put_client(CLIENT) | rbd_get_client()
kref_put() | (acquires node_lock)
kref->refcount becomes 0 | __rbd_client_find() returns CLIENT
calls rbd_client_release() | kref_get(&CLIENT->kref);
| (releases node_lock)
(acquires node_lock) |
deletes CLIENT from list | ...and starts using CLIENT...
(releases node_lock) |
and frees CLIENT | <-- but CLIENT gets freed here
Fix this by having rbd_put_client() acquire node_lock. The result
could still be improved, but at least it avoids this problem.
Signed-off-by: Alex Elder <elder@dreamhost.com>
Signed-off-by: Sage Weil <sage@newdream.net>
If an existing rbd client is found to be suitable for use in
rbd_get_client(), the rbd_options structure is not being
freed as it should. Fix that.
Signed-off-by: Alex Elder <elder@dreamhost.com>
Signed-off-by: Sage Weil <sage@newdream.net>
The Netlogic XLP SoC's on-chip USB controller appears as a PCI
USB device, but does not need the EHCI/OHCI handoff done in
usb/host/pci-quirks.c.
The pci-quirks.c is enabled for all vendors and devices, and is
enabled if USB and PCI are configured.
If we do not skip the qurik handling on XLP, the readb() call in
ehci_bios_handoff() will cause a crash since byte access is not
supported for EHCI registers in XLP.
Signed-off-by: Jayachandran C <jayachandranc@netlogicmicro.com>
Cc: stable <stable@vger.kernel.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
when missing USB PHY clock, kernel booting up will halt during USB
initialization. We should check USBGP[PHY_CLK_VALID] bit to avoid
CPU hang in this case.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This otg driver depends on marvell EHCI driver, so add the dependence.
It can fix the following build error on i386:
ERROR: "usb_remove_hcd" [drivers/usb/otg/mv_otg.ko] undefined!
ERROR: "usb_add_hcd" [drivers/usb/otg/mv_otg.ko] undefined!
Signed-off-by: Neil Zhang <zhangwm@marvell.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Distinguish Kconfig text by providing the Freescale family name.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is a possible data corruption if an RNDIS message goes beyond page
boundary in the sending code path. This patch fixes the problem.
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For code path not on the xmit, use netif_tx_disable() instead of
netif_stop_queue() to ensure other CPUs are not doing xmit.
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
PTR_ERR should be called before its argument is cleared.
The semantic match that finds this problem is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@@
expression e,e1;
constant c;
@@
*e = c
... when != e = e1
when != &e
when != true IS_ERR(e)
*PTR_ERR(e)
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Reported-by: Josh Triplett <josh@joshtriplett.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The packets with size larger than 1452 will be dropped by bridge
which with two hyperv netdevice ports. This cause by hyperv netvsc
driver always copy the trailer padding to the data packet, and then
the skb received from netdevice may include wrong skb->len (20 bytes
larger than the real size normally). The captured packet may like
this:
Ethernet II, Src: Microsof_00:00:07 (00:15:5d:00:00:07),
Dst: HewlettP_00:00:4e (00:1f:29:00:00:4e)
Destination: HewlettP_e6:00:4e (00:1f:29:00:00:4e)
Source: Microsof_f6:6d:07 (00:15:5d:f6:6d:07)
Type: IP (0x0800)
Trailer: 1415161718191A1B1C1D1E1F20212223
Frame check sequence: 0x24252627 [incorrect, should be 0x7c2e5a5e]
The following command help to reproduction it, and the ping ICMP
packets will be dropped by bridge.
$ ping ip -s 1453
This patch fixed it by removing the trailer padding from the data
packet.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
drm/radeon/kms/blit: fix blit copy for very large buffers
drm/radeon/kms: fix TRAVIS panel setup
drm/radeon: fix use after free in ATRM bios reading code.
drm/radeon/kms: Fix device tree linkage of DP i2c buses too
drm/radeon: Set DESKTOP_HEIGHT register to the framebuffer (not mode) height.
drm/radeon/kms: disable output polling when suspended
drm/nv50/pm: signedness bug in nv50_pm_clocks_pre()
drm/nouveau/gem: fix fence_sync race / oops
drm/nouveau: fix typo on mxmdcb option
drm/nouveau/mxm: pretend to succeed, even if we can't shadow the MXM-SIS
drm/nouveau/disp: check that panel power gpio is enabled at init time
With the movement of the cpu sysdev code to be real stuct devices, now
when we remove a cpu from the system, the driver core rightfully
complains that there is not a release method for this device.
For now, paper over this issue by quieting the driver core, but comment
this in detail. This will be resolved in future kernels to be solved
properly.
Reported-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Tested-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Evergreen and NI blit copy was broken if the buffer maps to a rectangle
whose one dimension is 16384 (max dimension allowed by these chips).
In the mainline kernel, the problem is exposed only when buffers are
very large (1G), but it's still a problem. The problem could be exposed
for smaller buffers if anyone modifies the algorithm for rectangle
construction in r600_blit_create_rect() (the reason why someone would
modify that algorithm is to tune the performance of buffer moves).
The root cause was in i2f() function which only operated on range between
0 and 16383. Fix this by extending the range of i2f() function to 0 to
32767.
While at it improve the function so that the range can be easily
extended in the future (if it becomes necessary), cleanup lines
over 80 characters, and replace in-line comments with one strategic
comment that explains the crux of the function.
Credits to michel@daenzer.net for pointing out the root cause of
the bug.
v2: Fix I2F_MAX_INPUT constant definition goof and warn only once
if input argument is out of range. Edit the comment a little
bit to avoid some linguistic confusion and make it look better
in general.
Signed-off-by: Ilija Hadzic <ihadzic@research.bell-labs.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Michel Dänzer <michel@daenzer.net>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Different versions of the DP to LVDS bridge chip
need different panel mode settings depending on
the chip version used.
Fixes:
https://bugs.freedesktop.org/show_bug.cgi?id=41569
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
Commit 6584cb88 (ARM i.MX dma: Fix burstsize settings) fixed
the mxcmmc driver but forgot to fix the SDMA driver to handle the
correct burtsize.
This make the SD card access works again with DMA on i.MX31 boards.
Signed-off-by: Philippe Rétornaz <philippe.retornaz@epfl.ch>
Tested-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
This bug was introduced by commit 54be5663
"gpio-ml-ioh: Support interrupt function" which adds a spinlock to struct
ioh_gpio but never init the spinlock.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
This bug was introduced by commit d568a681
"gpio-pch: add spinlock in suspend/resume processing"
which adds a spinlock to struct pch_gpio but never init the spinlock.
Reported-by: Tomoya MORINAGA <tomoya.rohm@gmail.com>
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Add workarounds table entries for hardware bugs in
- FireWire part of Sound Blaster Audigy cards,
- Ricoh PCIe 1394 controllers.
Without these, several protocols, e.g. AV/C, do not work on the
Audigy, and the Ricoh PCIe controllers wouldn't work at all.
This does not concern the older Ricoh PCI controllers.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.17 (GNU/Linux)
iQIcBAABAgAGBQJPJ/k1AAoJEHnzb7JUXXnQBWcP/Ao0EA9pw46YvQQ2jDwMlHfR
k76TntuUKJhVHCLUNvQjHGjNKiAkfKXeIu+a1XNAr8byVqDEbZEQpJheOVG3/O0Z
GyxS+Y/9Sy2JRED0ouWygGW1dN73Cw6GgvxfB6GzhPInq4wrdbdHIZ5XKE49kwyi
tz8gu/TE70e/0Y8MkfBdxJEOR1gmJwqFnVnZayaTV+qtBBnWaBIBkDThIQbmhJBw
oMYBfbs3V32d10GChTGv5LksVUil6tFpbW45x6xcIu24/c0R20033XP8fHEoXtXy
kQ3CnfBtFbsMeXHvbePwo/SVJUgk0oUBmLPVQmDOL30S6P3mV204ED+RsrwyrTdO
sIKWErgdJL/ApfGnqs4fg7cvSWsX3CFCKwztHG4wF1LDVofhq2uWM1ys/REOMTCX
zFPdbKwAPfFCwlZO4mhT1UXPHEzNTgZRzIqKpiowjLjx+cnXv0vOEPDQheSknRw5
416PAw7aWSz8VGmbZM063aFrtAmbq1jzLrtaIAjn7ha/2K/ys0/PaXBRwDClZNZ3
5ZA6u1TwFWFOYbuJ7ImwvSbC9C2LeWHUxDJ/8OCi9RFA78aEpSlhEyRfAmkKAetJ
hJVchUvJfP3LzEZ+IMNrWkI3H3Jf5MfcUvfZwNN2S6BvqDGlqYD+ldXhtHF5VyY2
l0KR4CsAvuQeL4gUxinP
=3Utr
-----END PGP SIGNATURE-----
Merge tag 'firewire-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/ieee1394/linux1394
firewire fixes post v3.3-rc1
Add workarounds table entries for hardware bugs in
- FireWire part of Sound Blaster Audigy cards,
- Ricoh PCIe 1394 controllers.
Without these, several protocols, e.g. AV/C, do not work on the
Audigy, and the Ricoh PCIe controllers wouldn't work at all.
This does not concern the older Ricoh PCI controllers.
* tag 'firewire-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/ieee1394/linux1394:
firewire: ohci: disable MSI on Ricoh controllers
firewire: ohci: add reset packet quirk for SB Audigy
Add MODULE_LICENSE() as per the license in the comment at the top of the
file for this source module to fix build warning:
WARNING: modpost: missing MODULE_LICENSE() in drivers/staging/media/go7007/go7007-usb.o
see include/linux/module.h for more information
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Cc: Ross Cohen <rcohen@snurgle.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
As ZTE have and will use more pid for new products this year,
so we need to add some new zte 3g-dongle's pid on option.c ,
and delete one pid 0x0154 because it use for mass-storage port.
Signed-off-by: Rui li <li.rui27@zte.com.cn>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 15c9a0acc3 (of: create of_phandle_args to simplify return of phandle
parsing data) modifies the parameter list of of_xlate function pointer declaration
in gpio_chip. Adapt the gpio specifier translate function for this change.
Reported-by: Tushar Behera <tushar.behera@linaro.org>
Signed-off-by: Thomas Abraham <thomas.abraham@linaro.org>
Tested-by: Karol Lewandowski <k.lewandowsk@samsung.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
We've found that qcserial devices will not always wake up reliably
from autosuspend, so disable it.
Signed-off-by: Thomas Tuttle <ttuttle@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
- Fix a crash due to a regression (uninitialized refcnt) introduced in
3.2 with XRC support.
- Close race in how ucma reports events when connect fails.
- Process vendor-specific MADs in mlx4 so that eg FDR-10 data rate works.
- Fix regression in qib caused by over-aggressive PCIe tuning.
- Other small fixes for hardware drivers (ipath, nes, qib).
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=81hM
-----END PGP SIGNATURE-----
Merge tag 'rdma-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband
InfiniBand/RDMA fixes for 3.3:
- Fix a crash due to a regression (uninitialized refcnt) introduced in
3.2 with XRC support.
- Close race in how ucma reports events when connect fails.
- Process vendor-specific MADs in mlx4 so that eg FDR-10 data rate works.
- Fix regression in qib caused by over-aggressive PCIe tuning.
- Other small fixes for hardware drivers (ipath, nes, qib).
* tag 'rdma-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband:
RDMA/nes: Copyright update
IB/mlx4: pass SMP vendor-specific attribute MADs to firmware
RDMA/nes: Fix fast memory registration opcode
RDMA/nes: Fix fast memory registration length
RDMA/ucma: Discard all events for new connections until accepted
IB/qib: Roll back PCIe tuning change
IB/qib: Use GFP_ATOMIC when locks are held
RDMA/nes: Add missing rcu_read_unlock() in nes_addr_resolve_neigh()
RDMA/nes: Fix for sending MPA reject frame
IB/ipath: Calling PTR_ERR() on right variable in create_file()
RDMA/core: Fix kernel panic by always initializing qp->usecnt
In my AMPDU rework, I rely on the sequence numbers of frames. But
I didn't check that the frame has a valid tid before updating the
tracking counters. As a result, the Tx queues were stalled. People
who hit this bug saw that we simply didn't let any data out.
This bug was introduced in 3.3.
This patch fixes that and checks that the frame is a QoS frame before
looking at its tid and changing the counters.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ssb supports one extra device on the cardbus. This results in two
devices in total, one beeing the host controller itself and the other
the external device connected to the hostcontroller over cardbus.
This makes the cardbus slot work on the Linksys WRT150N.
Reported-by: Aaron Z <aaronz@pls-net.org>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch correct the type of variables containing the rssi
values read from the rxwi.
In function rt2800_agc_to_rssi() 3 variables (rssi0, rssi1, rss2)
defined as int was assigned a 16bit signed values as unsigned.
From a test with a hi-gain antenna I verified that the rxwi
contains signed rssi values in the range -13/+81 (inclusive)
with 0 as an error condition. In case of negative values a
condition is triggered and the function return -128dBm while
the signal is at its maximum. This patch correct the cast so
negative values are not treated as very high positive values
(ex. -13 does not become 243).
Signed-off-by: Luigi Tarenga <luigi.tarenga@gmail.com>
Reviewed-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
bcma_bus_scan() leaks 'struct bcma_device' bytes if
bcma_get_next_core() returns error.
Restructure the code so we always kfree() the memory we allocate to
the variable 'core' before it goes out of scope.
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The parameters for ETHTOOL_FLASHDEV include a filename, which ought to
be null-terminated. Currently the only driver that implements
ethtool_ops::flash_device attempts to add a null terminator if
necessary, but does it wrongly. Do it in the ethtool core instead.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
skb->len after call eth_type_trans() does not include the ether
header size, but rx_bytes should account it.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
serio_raw_read now returns (sometimes partially) successful number of
bytes transferred to the caller, and only returns error code to the
caller on completely failed transfers.
Signed-off-by: Che-Liang Chiou <clchiou@chromium.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Linus Torvalds
Dave Airlie
Dan Carpenter
Nikolaus Schulz
Paul Walmsley
John Fastabend
Yi Zou
Alexander Duyck
Greg Rose
Dean Nelson
Guenter Roeck
Russell King
Axel Lin
Evgeniy Polyakov
David S. Miller
Roland Dreier
Greg Kroah-Hartman
Yinghai Lu
Paul Gortmaker
Anton Vorontsov
Larry Finger
Bart Westgeest
Omar Ramirez Luna
Arve Hjønnevåg
Seth Jennings
Randy Dunlap
Shuah Khan
Pekka Paalanen
Dan Magenheimer
Rob Clark
Julia Lawall
Greg Kroah-Hartman
Keith Packard
Dave Young
John W. Linville
Vivek Goyal
Paolo Bonzini
Daniel Vetter
Tomas Vanek
Atsushi Nemoto
Yoshihiro Shimoda
Jesper Juhl
Al Viro
stephen hemminger
Jiri Kosina
Asai Thambi S P
Martin Svec
Dax Kelson
Christoph Hellwig
Stephen Rothwell
Marco Sanvido
Nicholas Bellinger
Andy Grover
Sebastian Andrzej Siewior
NeilBrown
Thadeu Lima de Souza Cascardo
Henrik Rydberg
Eugenia Emantayev
Felix Fietkau
Amitkumar Karwar
Przemo Firszt
Danny Kukawka
Sylwester Nawrocki
David Lv
Guenter Roeck
Artem Bityutskiy
Samuel Thibault
Cong Wang
Milan Kocian
Mohammed Shafi Shajakhan
Peter Ujfalusi
Masanari Iida
Mitch A Williams
Don Skidmore
Matthijs Kooijman
Julia Lawall
Igor Murzov
Kukjin Kim
Stephane Grosjean
Sebastian Haas
Xi Wang
Wolfgang Grandegger
Wolfgang Zarre
Alex Elder
Jayachandran C
Shengzhou Liu
Neil Zhang
Fabio Estevam
Haiyang Zhang
Wei Yongjun
Ilija Hadzic
Alex Deucher
K. Y. Srinivasan
Ming Lei
Philippe Rétornaz
Rui li
Thomas Abraham
Thomas Tuttle
Emmanuel Grumbach
Hauke Mehrtens
Luigi Tarenga
Ben Hutchings
Che-Liang Chiou
Felipe Contreras