Restore the compatibility with the older code and make it possible to
suspend if the kernel command line doesn't contain the "resume=" argument
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Cc: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Heiko Carstens <heiko.carstens@de.ibm.com> wrote:
The boot sequence on s390 sometimes takes ages and we spend a very long
time (up to one or two minutes) in calibrate_migration_costs. The time
spent there differs from boot to boot. Also the calculated costs differ
a lot. I've seen differences by up to a factor of 15 (yes, factor not
percent). Also I doubt that making these measurements make much sense on
a completely virtualized architecture where you cannot tell how much cpu
time you will get anyway.
So introduce the CONFIG_DEFAULT_MIGRATION_COST method for an architecture
to set the scheduler migration costs. This turns off automatic detection
of migration costs. Makes sense on virtual platforms, where migration
costs are hard to measure accurately.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This provides an interface for arch code to find out how many
nanoseconds are going to be added on to xtime by the next call to
do_timer. The value returned is a fixed-point number in 52.12 format
in nanoseconds. The reason for this format is that it gives the
full precision that the timekeeping code is using internally.
The motivation for this is to fix a problem that has arisen on 32-bit
powerpc in that the value returned by do_gettimeofday drifts apart
from xtime if NTP is being used. PowerPC is now using a lockless
do_gettimeofday based on reading the timebase register and performing
some simple arithmetic. (This method of getting the time is also
exported to userspace via the VDSO.) However, the factor and offset
it uses were calculated based on the nominal tick length and weren't
being adjusted when NTP varied the tick length.
Note that 64-bit powerpc has had the lockless do_gettimeofday for a
long time now. It also had an extremely hairy routine that got called
from the 32-bit compat routine for adjtimex, which adjusted the
factor and offset according to what it thought the timekeeping code
was going to do. Not only was this only called if a 32-bit task did
adjtimex (i.e. not if a 64-bit task did adjtimex), it was also
duplicating computations from kernel/timer.c and it wasn't clear that
it was (still) correct.
The simple solution is to ask the timekeeping code how long the
current jiffy will be on each timer interrupt, after calling
do_timer. If this jiffy will be a different length from the last one,
we then need to compute new values for the factor and offset used in
the lockless do_gettimeofday. In this way we can keep xtime and
do_gettimeofday in sync, even when NTP is varying the tick length.
Note that when adjtimex varies the tick length, it almost always
introduces the variation from the next tick on. The only case I could
see where adjtimex would vary the length of the current tick is when
an old-style adjtime adjustment is being cancelled. (It's not clear
to me why the adjustment has to be cancelled immediately rather than
from the next tick on.) Thus I don't see any real need for a hook in
adjtimex; the rare case of an old-style adjustment being cancelled can
be fixed up at the next tick.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Acked-by: john stultz <johnstul@us.ibm.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
AMD SimNow!'s JIT doesn't like them at all in the guest. For distribution
installation it's easiest if it's a boot time option.
Also I moved the variable to a more appropiate place and make
it independent from sysctl
And marked __read_mostly which it is.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
I get about 88 squillion of these when suspending an old ad450nx server.
Cc: Pavel Roskin <proski@gnu.org>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix a latent bug in cpuset_exit() handling. If a task tried to allocate
memory after calling cpuset_exit(), it oops'd in
cpuset_update_task_memory_state() on a NULL cpuset pointer.
So set the exiting tasks cpuset to the root cpuset instead of to NULL.
A distro kernel hit this with an added kernel package that had just such a
hook (allocating memory) in the exit code path.
Signed-off-by: Paul Jackson <pj@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
1. The tracee can go from ptrace_stop() to do_signal_stop()
after __ptrace_unlink(p).
2. It is unsafe to __ptrace_unlink(p) while p->parent may wait
for tasklist_lock in ptrace_detach().
Signed-off-by: Oleg Nesterov <oleg@tv-sign.ru>
Cc: Roland McGrath <roland@redhat.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
copy_process:
attach_pid(p, PIDTYPE_PID, p->pid);
attach_pid(p, PIDTYPE_TGID, p->tgid);
What if kill_proc_info(p->pid) happens in between?
copy_process() holds current->sighand.siglock, so we are safe
in CLONE_THREAD case, because current->sighand == p->sighand.
Otherwise, p->sighand is unlocked, the new process is already
visible to the find_task_by_pid(), but have a copy of parent's
'struct pid' in ->pids[PIDTYPE_TGID].
This means that __group_complete_signal() may hang while doing
do ... while (next_thread() != p)
We can solve this problem if we reverse these 2 attach_pid()s:
attach_pid() does wmb()
group_send_sig_info() calls spin_lock(), which
provides a read barrier. // Yes ?
I don't think we can hit this race in practice, but still.
Signed-off-by: Oleg Nesterov <oleg@tv-sign.ru>
Cc: Roland McGrath <roland@redhat.com>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
There is a window after copy_process() unlocks ->sighand.siglock
and before it adds the new thread to the thread list.
In that window __group_complete_signal(SIGKILL) will not see the
new thread yet, so this thread will start running while the whole
thread group was supposed to exit.
I beleive we have another good reason to place attach_pid(PID/TGID)
under ->sighand.siglock. We can do the same for
release_task()->__unhash_process()
de_thread()->switch_exec_pids()
After that we don't need tasklist_lock to iterate over the thread
list, and we can simplify things, see for example do_sigaction()
or sys_times().
Signed-off-by: Oleg Nesterov <oleg@tv-sign.ru>
Cc: Roland McGrath <roland@redhat.com>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
CONFIG_TIME_LOW_RES is a temporary way for architectures to signal that
they simply return xtime in do_gettimeoffset(). In this corner-case we
want to round up by resolution when starting a relative timer, to avoid
short timeouts. This will go away with the GTOD framework.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Cc: Roman Zippel <zippel@linux-m68k.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Revert commit d7102e95b7b9c00277562c29aad421d2d521c5f6:
[PATCH] sched: filter affine wakeups
Apparently caused more than 10% performance regression for aim7 benchmark.
The setup in use is 16-cpu HP rx8620, 64Gb of memory and 12 MSA1000s with 144
disks. Each disk is 72Gb with a single ext3 filesystem (courtesy of HP, who
supplied benchmark results).
The problem is, for aim7, the wake-up pattern is random, but it still needs
load balancing action in the wake-up path to achieve best performance. With
the above commit, lack of load balancing hurts that workload.
However, for workloads like database transaction processing, the requirement
is exactly opposite. In the wake up path, best performance is achieved with
absolutely zero load balancing. We simply wake up the process on the CPU that
it was previously run. Worst performance is obtained when we do load
balancing at wake up.
There isn't an easy way to auto detect the workload characteristics. Ingo's
earlier patch that detects idle CPU and decide whether to load balance or not
doesn't perform with aim7 either since all CPUs are busy (it causes even
bigger perf. regression).
Revert commit d7102e95b7, which causes more
than 10% performance regression with aim7.
Signed-off-by: Ken Chen <kenneth.w.chen@intel.com>
Acked-by: Ingo Molnar <mingo@elte.hu>
Cc: Nick Piggin <nickpiggin@yahoo.com.au>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The PageCompound check before access_process_vm's set_page_dirty_lock is no
longer necessary, so remove it. But leave the PageCompound checks in
bio_set_pages_dirty, dio_bio_complete and nfs_free_user_pages: at least some
of those were introduced as a little optimization on hugetlb pages.
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
When panic_timeout is zero, suppress triggering a nested panic due to soft
lockup detection.
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
I don't think the code is quite ready, which is why I asked for Peter's
additions to also be merged before I acked it (although it turned out that
it still isn't quite ready with his additions either).
Basically I have had similar observations to Suresh in that it does not
play nicely with the rest of the balancing infrastructure (and raised
similar concerns in my review).
The samples (group of 4) I got for "maximum recorded imbalance" on a 2x2
SMP+HT Xeon are as follows:
| Following boot | hackbench 20 | hackbench 40
-----------+----------------+---------------------+---------------------
2.6.16-rc2 | 30,37,100,112 | 5600,5530,6020,6090 | 6390,7090,8760,8470
+nosmpnice | 3, 2, 4, 2 | 28, 150, 294, 132 | 348, 348, 294, 347
Hackbench raw performance is down around 15% with smpnice (but that in
itself isn't a huge deal because it is just a benchmark). However, the
samples show that the imbalance passed into move_tasks is increased by
about a factor of 10-30. I think this would also go some way to explaining
latency blips turning up in the balancing code (though I haven't actually
measured that).
We'll probably have to revert this in the SUSE kernel.
Cc: "Siddha, Suresh B" <suresh.b.siddha@intel.com>
Acked-by: Ingo Molnar <mingo@elte.hu>
Cc: Peter Williams <pwil3058@bigpond.net.au>
Cc: "Martin J. Bligh" <mbligh@aracnet.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch removes all self references and fixes references to files
in the now defunct arch/ppc64 tree. I think this accomplises
everything wanted, though there might be a few references I missed.
Signed-off-by: Jon Mason <jdmason@us.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Pointed out by Linus Torvalds.
sys_signal() forgets to initialize ->sa_mask.
( I suspect arch/ia64/ia32/ia32_signal.c:sys32_signal()
also needs this fix )
Signed-off-by: Oleg Nesterov <oleg@tv-sign.ru>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
A bunch of asm/bug.h includes are both not needed (since it will get
pulled anyway) and bogus (since they are done too early). Removed.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
If the file descriptor structure is being shared, allocate a new one and copy
information from the current, shared, structure.
Signed-off-by: Janak Desai <janak@us.ibm.com>
Cc: Al Viro <viro@ftp.linux.org.uk>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Michael Kerrisk <mtk-manpages@gmx.net>
Cc: Andi Kleen <ak@muc.de>
Cc: Paul Mackerras <paulus@samba.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
If vm structure is being shared, allocate a new one and copy information from
the current, shared, structure.
Signed-off-by: Janak Desai <janak@us.ibm.com>
Cc: Al Viro <viro@ftp.linux.org.uk>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Michael Kerrisk <mtk-manpages@gmx.net>
Cc: Andi Kleen <ak@muc.de>
Cc: Paul Mackerras <paulus@samba.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
If the namespace structure is being shared, allocate a new one and copy
information from the current, shared, structure.
Signed-off-by: Janak Desai <janak@us.ibm.com>
Cc: Al Viro <viro@ftp.linux.org.uk>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Michael Kerrisk <mtk-manpages@gmx.net>
Cc: Andi Kleen <ak@muc.de>
Cc: Paul Mackerras <paulus@samba.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
If filesystem structure is being shared, allocate a new one and copy
information from the current, shared, structure.
Signed-off-by: Janak Desai <janak@us.ibm.com>
Cc: Al Viro <viro@ftp.linux.org.uk>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Michael Kerrisk <mtk-manpages@gmx.net>
Cc: Andi Kleen <ak@muc.de>
Cc: Paul Mackerras <paulus@samba.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
sys_unshare system call handler function accepts the same flags as clone
system call, checks constraints on each of the flags and invokes corresponding
unshare functions to disassociate respective process context if it was being
shared with another task.
Here is the link to a program for testing unshare system call.
http://prdownloads.sourceforge.net/audit/unshare_test.c?download
Please note that because of a problem in rmdir associated with bind mounts and
clone with CLONE_NEWNS, the test fails while trying to remove temporary test
directory. You can remove that temporary directory by doing rmdir, twice,
from the command line. The first will fail with EBUSY, but the second will
succeed. I have reported the problem to Ram Pai and Al Viro with a small
program which reproduces the problem. Al told us yesterday that he will be
looking at the problem soon. I have tried multiple rmdirs from the
unshare_test program itself, but for some reason that is not working. Doing
two rmdirs from command line does seem to remove the directory.
Signed-off-by: Janak Desai <janak@us.ibm.com>
Cc: Al Viro <viro@ftp.linux.org.uk>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Michael Kerrisk <mtk-manpages@gmx.net>
Cc: Andi Kleen <ak@muc.de>
Cc: Paul Mackerras <paulus@samba.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix compilation problem in PM headers.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
- Remove unneeded bio_get() which would cause a bio leak
- Writing doesn't dirty pages. Reading dirties pages.
- We should dirty the pages after the IO completion, not before
(Busy-waiting for disk I/O completion isn't very polite.)
Signed-off-by: Pavel Machek <pavel@suse.cz>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
It may suck something awful, but it shouldn't taint the kernel.
Signed-off-by: Dave Jones <davej@redhat.com>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
migration_cost prints after every CPU hotplug event. Make it print only
once at boot.
Signed-off-by: Chuck Ebbert <76306.1226@compuserve.com>
Acked-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
percpu_data blindly allocates bootmem memory to store NR_CPUS instances of
cpudata, instead of allocating memory only for possible cpus.
As a preparation for changing that, we need to convert various 0 -> NR_CPUS
loops to use for_each_cpu().
(The above only applies to users of asm-generic/percpu.h. powerpc has gone it
alone and is presently only allocating memory for present CPUs, so it's
currently corrupting memory).
Signed-off-by: Eric Dumazet <dada1@cosmosbay.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: James Bottomley <James.Bottomley@steeleye.com>
Acked-by: Ingo Molnar <mingo@elte.hu>
Cc: Jens Axboe <axboe@suse.de>
Cc: Anton Blanchard <anton@samba.org>
Acked-by: William Irwin <wli@holomorphy.com>
Cc: Andi Kleen <ak@muc.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Five callsites. I dunno how all this crap got back in there :(
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
kernel/cpuset.c:644:38: warning: non-ANSI function declaration of function 'cpuset_update_task_memory_state'
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Acked-by: Paul Jackson <pj@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
- In case of a negative nsec value the result of the division must be
normalized.
- Remove inline from an exported function.
Signed-off-by: George Anzinger <george@wildturkeyranch.net>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
When one module exports a function symbol and another module uses that
symbol then kallsyms shows the symbol twice. Once from the consumer with a
type of 'U' and once from the provider with a type of 't' or 'T'. On most
architectures, both entries have the same address so it does not matter
which one is returned by kallsyms_lookup_name(). But on architectures with
function descriptors, the 'U' entry points to the descriptor, not to the
code body, which is not what we want.
IA64 # grep -w qla2x00_remove_one /proc/kallsyms
a000000208c25ef8 U qla2x00_remove_one [qla2300] <= descriptor
a000000208bf44c0 t qla2x00_remove_one [qla2xxx] <= function body
Tell kallsyms_lookup_name() to ignore type U entries in modules.
Signed-off-by: Keith Owens <kaos@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
When two function-return probes are inserted on kfree()[1] and the second
on say, sys_link()[2], and later [2] is unregistered, we have a deadlock as
kfree is called with the kretprobe_lock held and the function-return probe
on kfree will also try to grab the same lock.
However, we can move the kfree() during unregistration to outside the
spinlock as we are sure that no instances from the free list will be used
after synchronized_sched() returns during the unregistration process.
Thanks to Masami Hiramatsu for spotting this.
Signed-off-by: Ananth N Mavinakayanahalli <ananth@in.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
kernel/kprobes.c:353: warning: 'pre_handler_kretprobe' defined but not used
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Acked-by: Ananth N Mavinakayanahalli <ananth@in.ibm.com>
Acked-by: "Keshavamurthy, Anil S" <anil.s.keshavamurthy@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Currently the zone_reclaim code has a fixed window of 30 seconds of off node
allocations should a local zone have no unused pagecache pages left. Reclaim
will be attempted again after this timeout period to avoid repeated useless
scans for memory. This is also useful to established sufficiently large off
node allocation chunks to relieve the local node.
It may be beneficial to adjust that time period for some special situations.
For example if memory use was exceeding node capacity one may want to give up
for longer periods of time. If memory spikes intermittendly then one may want
to shorten the time period to reduce the number of off node allocations.
This patch allows just that....
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
- If we only reclaim nr_pages then its okay to stay on node.
Switch from > to >= for the comparison.
- vm_table[] entry for zone_reclaim_mode is a bit screwed up.
- Add empty lines around shrink_zone to show that this is the
central function to be called.
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Prevent the kernel from setting the log level to 10 unconditionally during
suspend/resume which was needed in the past for debugging, but generally is
undesirable.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Change sched_getaffinity() so that it returns a bitmap that indicates the
legally schedulable cpus that a task is allowed to run on.
Without this patch, if CONFIG_HOTPLUG_CPU is enabled, sched_getaffinity()
unconditionally returns (at least on IA64) a mask with NR_CPUS bits set.
This conveys no useful infornmation except for a kernel compile option.
This fixes a breakage we obseved running recent kernels. We have MPI jobs
that use sched_getaffinity() to determine where to place their threads.
Placing them on non-existant cpus is problematic :-)
Signed-off-by: Jack Steiner <steiner@sgi.com>
Acked-by: Ingo Molnar <mingo@elte.hu>
Cc: Nathan Lynch <ntl@pobox.com>
Cc: Paul Jackson <pj@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This function is neither used nor has any real contents.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The expiry time for relative timers with SIGEV_NONE set was never
updated to the correct value.
Pointed out by George Anzinger.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
At some point we added credits to people who actively helped to bring
k/hr-timers along. This was lost in the big code revamp. Add it back.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Clean up the interface to hrtimers by changing the init code to pass the mode
as well as the clock. This allow the init code to select the correct base and
eliminates extra timer re-init code in posix-timers. We also simplify the
restart interface nanosleep use.
Signed-off-by: George Anzinger <george@mvista.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
From: Steven Rostedtrostedt@goodmis.org <rostedt@goodmis.org>
CPU0 expires a posix-timer and runs the callback function. The signal is
queued.
After releasing the posix-timer lock and before returning to hrtimer_run_queue
CPU0 gets interrupted. CPU1 delivers the queued signal and rearms the timer.
CPU0 comes back to hrtimer_run_queue and sets the timer state to expired.
The next modification of the timer can result in an oops, because the state
information is wrong.
Keep track of state = RUNNING and check if the state has been in the return
path of hrtimer_run_queue. In case the state has been changed, ignore a
restart request and do not touch the state variable.
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This resolves bugzilla bug#5617. The oldvalue of the timer was read after the
timer was cancelled, so the remaining time was always zero.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fixup the conversion of posix-timers to hrtimers.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The itimer conversion removed the locking which protects the timer and
variables in the shared signal structure. Steven Rostedt found the problem in
the latest -rt patches.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Make swsusp use bytes as the image size units, which is needed for future
compatibility.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
I get storms of warnings from local_bh_enable(). Better-tested patches,
please.
Cc: Ingo Molnar <mingo@elte.hu>
Cc: "Paul E. McKenney" <paulmck@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
rcu_torture_lock is used in a softirq-unsafe manner, but it is also
taken by rcu_torture_cb(), which may execute in softirq-context,
resulting in potential deadlocks.
The fix is to acquire rcu_torture_lock in a softirq-safe manner. With
this fix applied, the rcu-torture code passes validation.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Acked-by: Paul E. McKenney <paulmck@us.ibm.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
RCU task-struct freeing can call free_uid(), which is taking
uidhash_lock - while other users of uidhash_lock are softirq-unsafe.
The fix is to always take the uidhash_spinlock in a softirq-safe manner.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Acked-by: Paul E. McKenney <paulmck@us.ibm.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This reduces the amount of time the migration cost calculations cost
during bootup. Based on numbers by Tony Luck <tony.luck@intel.com>.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
EDAC requires a way to scrub memory if an ECC error is found and the chipset
does not do the work automatically. That means rewriting memory locations
atomically with respect to all CPUs _and_ bus masters. That means we can't
use atomic_add(foo, 0) as it gets optimised for non-SMP
This adds a function to include/asm-foo/atomic.h for the platforms currently
supported which implements a scrub of a mapped block.
It also adjusts a few other files include order where atomic.h is included
before types.h as this now causes an error as atomic_scrub uses u32.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The TIF_RESTORE_SIGMASK flag allows us to have a generic implementation of
sys_rt_sigsuspend() instead of duplicating it for each architecture. This
provides such an implementation and makes arch/powerpc use it.
It also tidies up the ppc32 sys_sigsuspend() to use TIF_RESTORE_SIGMASK.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Currently, a negative policy argument passed into the
'sys_sched_setscheduler()' system call, will return with success. However,
the manpage for 'sys_sched_setscheduler' says:
EINVAL The scheduling policy is not one of the recognized policies, or the
parameter p does not make sense for the policy.
Signed-off-by: Jason Baron <jbaron@redhat.com>
Acked-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
proc support for zone reclaim
This patch creates a proc entry /proc/sys/vm/zone_reclaim_mode that may be
used to override the automatic determination of the zone reclaim made on
bootup.
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Build kernel/intermodule.c only when required.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix a comment which missed an update cycle somewhere.
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The problem, reported in:
http://bugzilla.kernel.org/show_bug.cgi?id=5859
and by various other email messages and lkml posts is that the cpuset hook
in the oom (out of memory) code can try to take a cpuset semaphore while
holding the tasklist_lock (a spinlock).
One must not sleep while holding a spinlock.
The fix seems easy enough - move the cpuset semaphore region outside the
tasklist_lock region.
This required a few lines of mechanism to implement. The oom code where
the locking needs to be changed does not have access to the cpuset locks,
which are internal to kernel/cpuset.c only. So I provided a couple more
cpuset interface routines, available to the rest of the kernel, which
simple take and drop the lock needed here (cpusets callback_sem).
Signed-off-by: Paul Jackson <pj@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Remove useless spin_retry_counter and fix compilation for UP kernels.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Remove the "inline" keyword from a bunch of big functions in the kernel with
the goal of shrinking it by 30kb to 40kb
Signed-off-by: Arjan van de Ven <arjan@infradead.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Acked-by: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add a new SCHED_BATCH (3) scheduling policy: such tasks are presumed
CPU-intensive, and will acquire a constant +5 priority level penalty. Such
policy is nice for workloads that are non-interactive, but which do not
want to give up their nice levels. The policy is also useful for workloads
that want a deterministic scheduling policy without interactivity causing
extra preemptions (between that workload's tasks).
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Cc: Michael Kerrisk <mtk-manpages@gmx.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
I tried to send the forcedeth maintainer an email, but it came back with:
"The mail address manfreds@colorfullife.com is not read anymore.
Please resent your mail to manfred@ instead of manfreds@."
This patch fixes this.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
This patch fixes a typo in the dependencies of SOFTWARE_SUSPEND.
This patch is based on a report by
Jean-Luc Leger <reiga@dspnet.fr.eu.org>.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Acked-by: Pavel Machek <pavel@ucw.cz>
)
From: Nick Piggin <nickpiggin@yahoo.com.au>
Track the last waker CPU, and only consider wakeup-balancing if there's a
match between current waker CPU and the previous waker CPU. This ensures
that there is some correlation between two subsequent wakeup events before
we move the task. Should help random-wakeup workloads on large SMP
systems, by reducing the migration attempts by a factor of nr_cpus.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Nick Piggin <npiggin@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
)
From: Ingo Molnar <mingo@elte.hu>
This is the latest version of the scheduler cache-hot-auto-tune patch.
The first problem was that detection time scaled with O(N^2), which is
unacceptable on larger SMP and NUMA systems. To solve this:
- I've added a 'domain distance' function, which is used to cache
measurement results. Each distance is only measured once. This means
that e.g. on NUMA distances of 0, 1 and 2 might be measured, on HT
distances 0 and 1, and on SMP distance 0 is measured. The code walks
the domain tree to determine the distance, so it automatically follows
whatever hierarchy an architecture sets up. This cuts down on the boot
time significantly and removes the O(N^2) limit. The only assumption
is that migration costs can be expressed as a function of domain
distance - this covers the overwhelming majority of existing systems,
and is a good guess even for more assymetric systems.
[ People hacking systems that have assymetries that break this
assumption (e.g. different CPU speeds) should experiment a bit with
the cpu_distance() function. Adding a ->migration_distance factor to
the domain structure would be one possible solution - but lets first
see the problem systems, if they exist at all. Lets not overdesign. ]
Another problem was that only a single cache-size was used for measuring
the cost of migration, and most architectures didnt set that variable
up. Furthermore, a single cache-size does not fit NUMA hierarchies with
L3 caches and does not fit HT setups, where different CPUs will often
have different 'effective cache sizes'. To solve this problem:
- Instead of relying on a single cache-size provided by the platform and
sticking to it, the code now auto-detects the 'effective migration
cost' between two measured CPUs, via iterating through a wide range of
cachesizes. The code searches for the maximum migration cost, which
occurs when the working set of the test-workload falls just below the
'effective cache size'. I.e. real-life optimized search is done for
the maximum migration cost, between two real CPUs.
This, amongst other things, has the positive effect hat if e.g. two
CPUs share a L2/L3 cache, a different (and accurate) migration cost
will be found than between two CPUs on the same system that dont share
any caches.
(The reliable measurement of migration costs is tricky - see the source
for details.)
Furthermore i've added various boot-time options to override/tune
migration behavior.
Firstly, there's a blanket override for autodetection:
migration_cost=1000,2000,3000
will override the depth 0/1/2 values with 1msec/2msec/3msec values.
Secondly, there's a global factor that can be used to increase (or
decrease) the autodetected values:
migration_factor=120
will increase the autodetected values by 20%. This option is useful to
tune things in a workload-dependent way - e.g. if a workload is
cache-insensitive then CPU utilization can be maximized by specifying
migration_factor=0.
I've tested the autodetection code quite extensively on x86, on 3
P3/Xeon/2MB, and the autodetected values look pretty good:
Dual Celeron (128K L2 cache):
---------------------
migration cost matrix (max_cache_size: 131072, cpu: 467 MHz):
---------------------
[00] [01]
[00]: - 1.7(1)
[01]: 1.7(1) -
---------------------
cacheflush times [2]: 0.0 (0) 1.7 (1784008)
---------------------
Here the slow memory subsystem dominates system performance, and even
though caches are small, the migration cost is 1.7 msecs.
Dual HT P4 (512K L2 cache):
---------------------
migration cost matrix (max_cache_size: 524288, cpu: 2379 MHz):
---------------------
[00] [01] [02] [03]
[00]: - 0.4(1) 0.0(0) 0.4(1)
[01]: 0.4(1) - 0.4(1) 0.0(0)
[02]: 0.0(0) 0.4(1) - 0.4(1)
[03]: 0.4(1) 0.0(0) 0.4(1) -
---------------------
cacheflush times [2]: 0.0 (33900) 0.4 (448514)
---------------------
Here it can be seen that there is no migration cost between two HT
siblings (CPU#0/2 and CPU#1/3 are separate physical CPUs). A fast memory
system makes inter-physical-CPU migration pretty cheap: 0.4 msecs.
8-way P3/Xeon [2MB L2 cache]:
---------------------
migration cost matrix (max_cache_size: 2097152, cpu: 700 MHz):
---------------------
[00] [01] [02] [03] [04] [05] [06] [07]
[00]: - 19.2(1) 19.2(1) 19.2(1) 19.2(1) 19.2(1) 19.2(1) 19.2(1)
[01]: 19.2(1) - 19.2(1) 19.2(1) 19.2(1) 19.2(1) 19.2(1) 19.2(1)
[02]: 19.2(1) 19.2(1) - 19.2(1) 19.2(1) 19.2(1) 19.2(1) 19.2(1)
[03]: 19.2(1) 19.2(1) 19.2(1) - 19.2(1) 19.2(1) 19.2(1) 19.2(1)
[04]: 19.2(1) 19.2(1) 19.2(1) 19.2(1) - 19.2(1) 19.2(1) 19.2(1)
[05]: 19.2(1) 19.2(1) 19.2(1) 19.2(1) 19.2(1) - 19.2(1) 19.2(1)
[06]: 19.2(1) 19.2(1) 19.2(1) 19.2(1) 19.2(1) 19.2(1) - 19.2(1)
[07]: 19.2(1) 19.2(1) 19.2(1) 19.2(1) 19.2(1) 19.2(1) 19.2(1) -
---------------------
cacheflush times [2]: 0.0 (0) 19.2 (19281756)
---------------------
This one has huge caches and a relatively slow memory subsystem - so the
migration cost is 19 msecs.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Ashok Raj <ashok.raj@intel.com>
Signed-off-by: Ken Chen <kenneth.w.chen@intel.com>
Cc: <wilder@us.ibm.com>
Signed-off-by: John Hawkes <hawkes@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Roman Zippel pointed out that the missing lower limit of intervals
leads to an accounting error in the overrun count. Enforce the lower
limit of intervals to resolution in the timer forwarding code.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Change the storage format of the per base resolution to ktime_t to
make it easier accessible in the hrtimers code.
Change the resolution from (NSEC_PER_SEC/HZ) to TICK_NSEC as Roman
pointed out. TICK_NSEC is closer to the real resolution.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The list_head in the hrtimer structure was introduced for easy access
to the first timer with the further extensions of real high resolution
timers in mind, but it turned out in the course of development that
it is not necessary for the standard use case. Remove the list head
and access the first expiry timer by a datafield in the timer base.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
vSMP specific alignment patch to
1. Define INTERNODE_CACHE_SHIFT for vSMP
2. Use this for alignment of critical structures
3. Use INTERNODE_CACHE_SHIFT for ARCH_MIN_TASKALIGN,
and let the slab align task_struct allocations to the internode cacheline size
4. Introduce and use ARCH_MIN_MMSTRUCT_ALIGN for mm_struct slab allocations.
Signed-off-by: Ravikiran Thirumalai <kiran@scalemp.com>
Signed-off-by: Shai Fultheim <shai@scalemp.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
They are referred to often so avoid potential false sharing for them.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
- Move capable() from sched.h to capability.h;
- Use <linux/capability.h> where capable() is used
(in include/, block/, ipc/, kernel/, a few drivers/,
mm/, security/, & sound/;
many more drivers/ to go)
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Uninline capable(). Saves 2K of kernel text on a generic .config, and 1K on a
tiny config. In addition it makes the use of capable more consistent between
CONFIG_SECURITY and !CONFIG_SECURITY
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
When a kprobes modules is written in such a way that probes are inserted on
itself, then unload of that moudle was not possible due to reference
couning on the same module.
The below patch makes a check and incrementes the module refcount only if
it is not a self probed module.
We need to allow modules to probe themself for kprobes performance
measurements
This patch has been tested on several x86_64, ppc64 and IA64 architectures.
Signed-off-by: Anil S Keshavamurthy <anil.s.keshavamurthy>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Let's switch mutex_debug_check_no_locks_freed() to take (addr, len) as
arguments instead, since all its callers were just calculating the 'to'
address for themselves anyway... (and sometimes doing so badly).
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Acked-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Mark mutex_lock() and mutex_lock_interruptible() as might_sleep()
functions.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Call the mutex slowpath more conservatively - e.g. FRAME_POINTERS can
change the calling convention, in which case a direct branch to the
slowpath becomes illegal. Bug found by Hugh Dickins.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Remove unnecessary (and incorrect) inclusion of asm/mutex.h, pointed out
by David Howells.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Pointed out by Srivatsa Vaddagiri <vatsa@in.ibm.com>.
rcu_do_batch() stops after processing maxbatch callbacks
on ->donelist leaving rcu_tasklet in TASKLET_STATE_SCHED
state.
If CPU_DEAD event happens remaining ->donelist entries are
lost, rcu_offline_cpu() kills this tasklet.
With this patch ->donelist migrates along with ->curlist
and ->nxtlist to the current cpu.
Compile tested.
Signed-off-by: Oleg Nesterov <oleg@tv-sign.ru>
Acked-by: Paul E. McKenney <paulmck@us.ibm.com>
Cc: Srivatsa Vaddagiri <vatsa@in.ibm.com>
Cc: Dipankar Sarma <dipankar@in.ibm.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch moves rcu_state into the rcu_ctrlblk. I think there
are no reasons why we should have 2 different variables to control
rcu state. Every user of rcu_state has also "rcu_ctrlblk *rcp" in
the parameter list.
Signed-off-by: Oleg Nesterov <oleg@tv-sign.ru>
Acked-by: Paul E. McKenney <paulmck@us.ibm.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
If a __deprecated is desired it should go to the prototype in the header
(where it currently isn't).
But at this place it's pointless.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Decrease the number of pointer derefs in kernel/exit.c
Benefits of the patch:
- Fewer pointer dereferences should make the code slightly faster.
- Size of generated code is smaller
- improved readability
Signed-off-by: Jesper Juhl <jesper.juhl@gmail.com>
Acked-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The following patch (against 2.6.15-rc5-mm3) fixes a kprobes build break
due to changes introduced in the kprobe locking in 2.6.15-rc5-mm3. In
addition, the patch reverts back the open-coding of kprobe_mutex.
Signed-off-by: Ananth N Mavinakayanahalli <ananth@in.ibm.com>
Acked-by: Anil S Keshavamurthy <anil.s.keshavamurthy@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Currently arch_remove_kprobes() is only implemented/required for x86_64 and
powerpc. All other architecture like IA64, i386 and sparc64 implementes a
dummy function which is being called from arch independent kprobes.c file.
This patch removes the dummy functions and replaces it with
#define arch_remove_kprobe(p, s) do { } while(0)
Signed-off-by: Anil S Keshavamurthy <anil.s.keshavamurthy@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Based on some feedback from Oleg Nesterov, I have made few changes to
previously posted patch.
Signed-off-by: Anil S Keshavamurthy <anil.s.keshavamurthy@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Since Kprobes runtime exception handlers is now lock free as this code path is
now using RCU to walk through the list, there is no need for the
register/unregister{_kprobe} to use spin_{lock/unlock}_isr{save/restore}. The
serialization during registration/unregistration is now possible using just a
mutex.
In the above process, this patch also fixes a minor memory leak for x86_64 and
powerpc.
Signed-off-by: Anil S Keshavamurthy <anil.s.keshavamurthy@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Kernel/kprobes.c defines get_insn_slot() and free_insn_slot() which are
currently required _only_ for x86_64 and powerpc (which has no-exec support).
FYI, get{free}_insn_slot() functions manages the memory page which is mapped
as executable, required for instruction emulation.
This patch moves those two functions under __ARCH_WANT_KPROBES_INSN_SLOT and
defines __ARCH_WANT_KPROBES_INSN_SLOT in arch specific kprobes.h file.
Signed-off-by: Anil S Keshavamurthy <anil.s.keshavamurthy@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This series removes the getnstimestamp() function from kernel/time.c in favor
of kernel/hrtimer.c's ktime_get_ts() function which currently does exactly the
same thing: retrieves a high-resolution (ns) timespec structure and performs
the wall_to_monotonic adjustment.
This patch:
Export ktime_get_ts() to be used as a timestamp function since it uses
getnstimefoday() and does the wall_to_monotonic adjustment.
Signed-off-by: Matt Helsley <matthltc@us.ibm.com>
Cc: john stultz <johnstul@us.ibm.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Switch clock_nanosleep to use the new nanosleep functions in hrtimer.c
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
introduce the hrtimer_nanosleep() and hrtimer_nanosleep_real() APIs. Not yet
used by any code.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
hrtimer subsystem core. It is initialized at bootup and expired by the timer
interrupt, but is otherwise not utilized by any other subsystem yet.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Check if the timespec which is provided from user space is normalized.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
add timespec_valid(ts) [returns false if the timespec is denorm]
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
add const arguments to the posix-timers.h API functions
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This is now uninlined, but some modules use it.
Make it a non-GPL export, since the inlined mktime() was also available that
way.
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
add 'const' to mktime arguments, and clean it up a bit
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
mktime() and set_normalized_timespec() are large inline functions used in many
places: deinline them.
From: George Anzinger, off-by-1 bugfix
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
make posix-timers.c use the generic calc64.h facility
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The comment in compat.c is wrong, every architecture provides a
get_compat_sigevent() for the IPC compat code already.
This basically moves the x86_64 version to common code and removes all the
others.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Paul Mackerras <paulus@samba.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: "David S. Miller" <davem@davemloft.net>
Acked-by: Andi Kleen <ak@muc.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
- Moving the crash_dump.c file to arch dependent part as kmap_atomic_pfn is
specific to i386 and highmem may not exist in other archs.
- Use ioremap for x86_64 to map the previous kernel memory.
- In copy_oldmem_page(), we now directly copy to the user/kernel buffer and
avoid the unneccesary copy to a kmalloc'd page.
Signed-off-by: Rachita Kothiyal <rachita@in.ibm.com>
Signed-off-by: Vivek Goyal <vgoyal@in.ibm.com>
Cc: Andi Kleen <ak@muc.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
- If system panics then cpu register states are captured through funciton
crash_get_current_regs(). This is not a inline function hence a stack frame
is pushed on to the stack and then cpu register state is captured. Later
this frame is popped and new frames are pushed (machine_kexec).
- In theory this is not very right as we are capturing register states for a
frame and that frame is no more valid. This seems to have created back
trace problems for ppc64.
- This patch fixes it up. The very first thing it does after entering
crash_kexec() is to capture the register states. Anyway we don't want the
back trace beyond crash_kexec(). crash_get_current_regs() has been made
inline
- crash_setup_regs() is the top architecture dependent function which should
be responsible for capturing the register states as well as to do some
architecture dependent tricks. For ex. fixing up ss and esp for i386.
crash_setup_regs() has also been made inline to ensure no new call frame is
pushed onto stack.
Signed-off-by: Vivek Goyal <vgoyal@in.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
- Kexec on panic functionality allocates memory for saving cpu registers in
case of system crash event. Address of this allocated memory needs to be
exported to user space, which is used by kexec-tools.
- Previously, a single /sys/kernel/crash_notes entry was being exported as
memory allocated was a single continuous array. Now memory allocation being
dyanmic and per cpu based, address of per cpu buffer is exported through
"/sys/devices/system/cpu/cpuX/crash_notes"
Signed-off-by: Vivek Goyal <vgoyal@in.ibm.com>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
- In case of system crash, current state of cpu registers is saved in memory
in elf note format. So far memory for storing elf notes was being allocated
statically for NR_CPUS.
- This patch introduces dynamic allocation of memory for storing elf notes.
It uses alloc_percpu() interface. This should lead to better memory usage.
- Introduced based on Andi Kleen's and Eric W. Biederman's suggestions.
- This patch also moves memory allocation for elf notes from architecture
dependent portion to architecture independent portion. Now crash_notes is
architecture independent. The whole idea is that size of memory to be
allocated per cpu (MAX_NOTE_BYTES) can be architecture dependent and
allocation of this memory can be architecture independent.
Signed-off-by: Vivek Goyal <vgoyal@in.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
I think it is better to set ->next_pending in the caller, when
it is needed. This saves one parameter, and this coincides with
cpu_quiet() beahaviour, which sets ->completed = ->cur itself.
Signed-off-by: Oleg Nesterov <oleg@tv-sign.ru>
Acked-by: Paul E. McKenney <paulmck@us.ibm.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch converts the inode semaphore to a mutex. I have tested it on
XFS and compiled as much as one can consider on an ia64. Anyway your
luck with it might be different.
Modified-by: Ingo Molnar <mingo@elte.hu>
(finished the conversion)
Signed-off-by: Jes Sorensen <jes@sgi.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
more mutex debugging: check for held locks during memory freeing,
task exit, enable sysrq printouts, etc.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Arjan van de Ven <arjan@infradead.org>
mutex implementation, core files: just the basic subsystem, no users of it.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Arjan van de Ven <arjan@infradead.org>
__rcu_pending() is rather fat and called twice from rcu_pending().
rcu_pending() has multiple callers, and not that small too.
This patch uninlines both of them.
Signed-off-by: Oleg Nesterov <oleg@tv-sign.ru>
Acked-by: Paul E. McKenney <paulmck@us.ibm.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This adds an option to remove vm86 support under CONFIG_EMBEDDED. Saves
about 5k.
This version eliminates most of the #ifdefs of the previous version and
instead uses function stubs in vm86.h. Also, release_vm86_irqs is moved
from asm-i386/irq.h to a more appropriate home in vm86.h so that the stubs
can live together.
$ size vmlinux-baseline vmlinux-novm86
text data bss dec hex filename
2920821 523232 190652 3634705 377611 vmlinux-baseline
2916268 523100 190492 3629860 376324 vmlinux-novm86
Signed-off-by: Matt Mackall <mpm@selenic.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Configurable 16-bit UID and friends support
This allows turning off the legacy 16 bit UID interfaces on embedded platforms.
text data bss dec hex filename
3330172 529036 190556 4049764 3dcb64 vmlinux-baseline
3328268 529040 190556 4047864 3dc3f8 vmlinux
From: Adrian Bunk <bunk@stusta.de>
UID16 was accidentially disabled for !EMBEDDED.
Signed-off-by: Matt Mackall <mpm@selenic.com>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Factor out common code for different RUSAGE_xxx cases.
Don't take ->sighand->siglock in RUSAGE_SELF case, suggested by Ravikiran G
Thirumalai <kiran@scalex86.org>.
Signed-off-by: Oleg Nesterov <oleg@tv-sign.ru>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Use first_cpu(cpu_possible_map) for the single-thread workqueue case. We
used to hardcode 0, but that broke on systems where !cpu_possible(0) when
workqueue_struct->cpu_workqueue_struct was changed from a static array to
alloc_percpu.
Commit id bce61dd49d ("Fix hardcoded cpu=0 in
workqueue for per_cpu_ptr() calls") fixed that for Ben's funky sparc64
system, but it regressed my Power5. Offlining cpu 0 oopses upon the next
call to queue_work for a single-thread workqueue, because now we try to
manipulate per_cpu_ptr(wq->cpu_wq, 1), which is uninitialized.
So we need to establish an unchanging "slot" for single-thread workqueues
which will have a valid percpu allocation. Since alloc_percpu keys off of
cpu_possible_map, which must not change after initialization, make this
slot == first_cpu(cpu_possible_map).
Signed-off-by: Nathan Lynch <ntl@pobox.com>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Remove the redundant spinlock in the function resolve_symbol() as we are
not altering the module list, and we already hold the semaphore.
Signed-off-by: Ashutosh Naik <ashutosh.naik@gmail.com>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Currently TAINT_FORCED_RMMOD is totally unused. Because it is marked as
TAINT_FORCED_MODULE instead when user forced a module unload. This patch
marks it correctly
Signed-off-by: Akinobu Mita <mita@miraclelinux.com>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Dave Jones <davej@codemonkey.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Ensure that an exported symbol does not already exist in the kernel or in
some other module's exported symbol table. This is done by checking the
symbol tables for the exported symbol at the time of loading the module.
Currently this is done after the relocation of the symbol.
Signed-off-by: Ashutosh Naik <ashutosh.naik@gmail.com>
Signed-off-by: Anand Krishnan <anandhkrishnan@yahoo.co.in>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
sys_setpgid() allows to change ->pgrp of ptraced childs.
'man setpgid' does not tell anything about that, so I consider
this behaviour is a bug.
Signed-off-by: Oleg Nesterov <oleg@tv-sign.ru>
Cc: Oren Laadan <orenl@cs.columbia.edu>
Cc: Roland McGrath <roland@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
setsid() does not work unless the calling process is a
thread_group_leader().
'man setpgid' does not tell anything about that, so I consider this
behaviour is a bug.
Signed-off-by: Oren Laadan <orenl@cs.columbia.edu>
Cc: Oleg Nesterov <oleg@tv-sign.ru>
Cc: Roland McGrath <roland@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
setpgid(0, pgid) or setpgid(forked_child_pid, pgid) does not work unless
the calling process is a thread_group_leader().
'man setpgid' does not tell anything about that, so I consider this
behaviour is a bug.
Signed-off-by: Oleg Nesterov <oleg@tv-sign.ru>
Cc: Oren Laadan <orenl@cs.columbia.edu>
Cc: Roland McGrath <roland@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
In fork, child should recopy parent's pgrp/tty after it has tasklist_lock.
Otherwise following a setpgid() on the parent, *after* copy_signal(), the
child will own a stale pgrp (which may be reused); (eg. if copy_mm()
sleeps a long while due to memory pressure). Similar issue for the tty.
Signed-off-by: Oren Laadan <orenl@cs.columbia.edu>
Cc: Oleg Nesterov <oleg@tv-sign.ru>
Cc: Roland McGrath <roland@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The problem. It is expected that /sbin/halt -p works exactly like
/sbin/halt, when the kernel does not implement power off functionality.
The kernel can do a lot of work in the reboot notifiers and in
device_shutdown before we even get to machine_power_off. Some of that
shutdown is not safe if you are leaving the power on, and it definitely
gets in the way of using sysrq or pressing ctrl-alt-del. Since the
shutdown happens in generic code there is no way to fix this in
architecture specific code :(
Some machines are kernel oopsing today because of this.
The simple solution is to turn LINUX_REBOOT_CMD_POWER_OFF into
LINUX_REBOOT_CMD_HALT if power_off functionality is not implemented.
This has the unfortunate side effect of disabling the power off
functionality on architectures that leave pm_power_off to null and still
implement something in machine_power_off. And it will break the build on
some architectures that don't have a pm_power_off variable at all.
On both counts I say tough.
For architectures like alpha that don't implement the pm_power_off variable
pm_power_off is declared in linux/pm.h and it is a generic part of our
power management code, and all architectures should implement it.
For architectures like parisc that have a default power off method in
machine_power_off if pm_power_off is not implemented or fails. It is easy
enough to set the pm_power_off variable. And nothing bad happens there,
the machines just stop powering off.
The current semantics are impossible without a flag at the top level so we
can avoid the problem code if a power off is not implemented. pm_power_off
is as good a flag as any with the bonus that it works without modification
on at least x86, x86_64, powerpc, and ppc today.
Andrew can you pick this up and put this in the mm tree. Kernels that
don't compile or don't power off seem saner than kernels that oops or
panic. Until we get the arch specific patches for the problem
architectures this probably isn't smart to push into the stable kernel.
Unfortunately I don't have the time at the moment to walk through every
architecture and make them work. And even if I did I couldn't test it :(
From: Hirokazu Takata <takata@linux-m32r.org>
Add pm_power_off() for build fix of arch/m32r/kernel/process.c.
From: Miklos Szeredi <miklos@szeredi.hu>
UML build fix
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Hayato Fujiwara <fujiwara@linux-m32r.org>
Signed-off-by: Hirokazu Takata <takata@linux-m32r.org>
Signed-off-by: Miklos Szeredi <miklos@szeredi.hu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch forces RCU torture threads off various CPUs in the system
allowing them to become idle and go tickless. Meant to test support for
such tickless idle CPU in RCU.
Signed-off-by: Srivatsa Vaddagiri <vatsa@in.ibm.com>
Cc: Dipankar Sarma <dipankar@in.ibm.com>
Cc: "Paul E. McKenney" <paulmck@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Kernels that have had Windows drivers loaded into them are undebuggable.
I've wasted a number of hours chasing bugs filed in Fedora bugzilla only to
find out much later that the user had used such 'helpers', and their
problems were unreproducable without them loaded.
Acked-by: Arjan van de Ven <arjan@infradead.org>
Signed-off-by: Dave Jones <davej@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Some long time ago, dentry struct was carefully tuned so that on 32 bits
UP, sizeof(struct dentry) was exactly 128, ie a power of 2, and a multiple
of memory cache lines.
Then RCU was added and dentry struct enlarged by two pointers, with nice
results for SMP, but not so good on UP, because breaking the above tuning
(128 + 8 = 136 bytes)
This patch reverts this unwanted side effect, by using an union (d_u),
where d_rcu and d_child are placed so that these two fields can share their
memory needs.
At the time d_free() is called (and d_rcu is really used), d_child is known
to be empty and not touched by the dentry freeing.
Lockless lookups only access d_name, d_parent, d_lock, d_op, d_flags (so
the previous content of d_child is not needed if said dentry was unhashed
but still accessed by a CPU because of RCU constraints)
As dentry cache easily contains millions of entries, a size reduction is
worth the extra complexity of the ugly C union.
Signed-off-by: Eric Dumazet <dada1@cosmosbay.com>
Cc: Dipankar Sarma <dipankar@in.ibm.com>
Cc: Maneesh Soni <maneesh@in.ibm.com>
Cc: Miklos Szeredi <miklos@szeredi.hu>
Cc: "Paul E. McKenney" <paulmck@us.ibm.com>
Cc: Ian Kent <raven@themaw.net>
Cc: Paul Jackson <pj@sgi.com>
Cc: Al Viro <viro@ftp.linux.org.uk>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Trond Myklebust <trond.myklebust@fys.uio.no>
Cc: Neil Brown <neilb@cse.unsw.edu.au>
Cc: James Morris <jmorris@namei.org>
Cc: Stephen Smalley <sds@epoch.ncsc.mil>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch removes unneeded sig->curr_target recalculation under 'if
(atomic_dec_and_test(&sig->count))' in __exit_signal().
When sig->count == 0 the signal can't be sent to this task and
next_thread(tsk) == tsk anyway.
Signed-off-by: Oleg Nesterov <oleg@tv-sign.ru>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
zap_other_threads() sets SIGNAL_GROUP_EXIT at the very start,
do_group_exit() doesn't need to do it.
Signed-off-by: Oleg Nesterov <oleg@tv-sign.ru>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
__create_workqueue() not checking return of alloc_percpu()
NULL dereference was possible.
Signed-off-by: Ben Collins <bcollins@ubuntu.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
While rooting aroung in the signal code trying to understand how to fix the
SIG_IGN ploy (set sig handler to SIG_IGN and flood system with high speed
repeating timers) I came across what, I think, is a problem in sigaction()
in that when processing a SIG_IGN request it flushes signals from 1 to
SIGRTMIN and leaves the rest. Attempt to fix this.
Signed-off-by: George Anzinger <george@mvista.com>
Cc: Roland McGrath <roland@redhat.com>
Cc: Linus Torvalds <torvalds@osdl.org>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
What's the true meaning of the printk return value? Should it include the
priority prefix length of 3? and what about the timing information? In
both cases it was broken:
strace -e write echo 1 > /dev/kmsg
=> write(1, "1\n", 2) = 5
strace -e write echo "<1>1" > /dev/kmsg
=> write(1, "<1>1\n", 5) = 8
The returned length was "length of input string + 3", I made it "length
of string output to the log buffer".
Note that I couldn't find any printk caller in the kernel interested by its
return value besides kmsg_write.
Signed-off-by: Guillaume Chazarain <guichaz@yahoo.fr>
Acked-By: Tim Bird <tim.bird@am.sony.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The ptrace_get_task_struct() helper that I added as part of the ptrace
consolidation is useful in variety of places that currently opencode it.
Switch them to the common helpers.
Add a ptrace_traceme() helper that needs to be explicitly called, and simplify
the ptrace_get_task_struct() interface. We don't need the request argument
now, and we return the task_struct directly, using ERR_PTR() for error
returns. It's a bit more code in the callers, but we have two sane routines
that do one thing well now.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Rafael J. Wysocki
Ingo Molnar
Paul Mackerras
Andi Kleen
Andrew Morton
Paul Jackson
Oleg Nesterov
Chen, Kenneth W
Hugh Dickins
Jan Beulich
Nick Piggin
Jon Mason
Al Viro
JANAK DESAI
Pavel Machek
Dave Jones
Chuck Ebbert
Eric Dumazet
Randy Dunlap
George Anzinger
Keith Owens
Ananth N Mavinakayanahalli
Adrian Bunk
Linus Torvalds
Christoph Lameter
Jack Steiner
Thomas Gleixner
Len Brown
Alan Cox
David Woodhouse
Jason Baron
Christoph Lameter
Jonathan Corbet
Martin Schwidefsky
Arjan van de Ven
Christian Kujau
Ravikiran G Thirumalai
Keshavamurthy Anil S
Ingo Molnar
Jesper Juhl
Matt Helsley
Christoph Hellwig
Vivek Goyal
Jes Sorensen
Matt Mackall
Nathan Lynch
Ashutosh Naik
Akinobu Mita
Oren Laadan
Eric W. Biederman
Srivatsa Vaddagiri
Ben Collins
George Anzinger
Guillaume Chazarain