MAX8997 driver disables automatic path selection from MicroUSB connector
and manually sets path to either UART or USB lines. However the code for
setting USB path worked only for USB host mode (when ID pin is set
to ground). When standard USB cable (USB device mode) is connected, path
registers are not touched. This means that once the non-USB accessory is
connected to MAX8997-operated micro USB port, the path is no longer set
to USB and USB device mode doesn't work. This patch fixes it by setting
USB path both for USB and USB host modes.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Driver unconditionally forces UART path during probe, probably to ensure
that one can get kernel serial log as soon as possible.
This approach causes some issues, especially when board is booted with
non-UART cable connected to micro-USB port. For example, when USB cable is
connected, UART TX/RX lines are unconditionally short-circuited to USB
D+/D- lines. This is in turn recognized by a series of serial BREAK
signals and some random characters when USB host tries to perform
enumeration procedure.
To solve the above issue and keep UART console operational as early as
possible, set UART path only when USB ID reports UART capable cable.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Driver unconditionally forces UART path during probe, probably to ensure
that one can get kernel serial log as soon as possible.
This approach causes some issues, especially when board is booted with
non-UART cable connected to micro-USB port. For example, when USB cable is
connected, UART TX/RX lines are unconditionally short-circuited to USB
D+/D- lines. This is in turn recognized by a series of serial BREAK
signals and some random characters when USB host tries to perform
enumeration procedure.
To solve the above issue and keep UART console operational as early as
possible, set UART path only when USB ID reports UART capable cable.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Driver unconditionally forces UART path during probe, probably to ensure
that one can get kernel serial log as soon as possible.
This approach causes some issues, especially when board is booted with
non-UART cable connected to micro-USB port. For example, when USB cable is
connected, UART TX/RX lines are unconditionally short-circuited to USB
D+/D- lines. This is in turn recognized by a series of serial BREAK
signals and some random characters when USB host tries to perform
enumeration procedure.
To solve the above issue and keep UART console operational as early as
possible, set UART path only when USB ID reports UART capable cable.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Driver unconditionally forces UART path during probe, probably to ensure
that one can get kernel serial log as soon as possible.
This approach causes some issues, especially when board is booted with
non-UART cable connected to micro-USB port. For example, when USB cable is
connected, UART TX/RX lines are unconditionally short-circuited to USB
D+/D- lines. This is in turn recognized by a series of serial BREAK
signals and some random characters when USB host tries to perform
enumeration procedure.
To solve the above issue and keep UART console operational as early as
possible, set UART path only when USB ID reports UART capable cable.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Convert driver to use SPDX identifier.
While here, fix MODULE_LICENSE() string to be the same as license text states.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Convert driver to use SPDX identifier.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
USBID is 2-bit bit field according to specification. Make it clear.
No functional change intended.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
There is no suffix MASK in the spec and other small spelling fixes.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
When we have first case to fall through it's not enough to put
single comment there to satisfy compiler. Instead of doing that,
return fall back value directly from default case.
This to avoid following warnings:
drivers/extcon/extcon-intel-cht-wc.c: In function ‘cht_wc_extcon_get_charger’:
include/linux/device.h:1420:2: warning: this statement may fall through [-Wimplicit-fallthrough=]
_dev_warn(dev, dev_fmt(fmt), ##__VA_ARGS__)
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/extcon/extcon-intel-cht-wc.c:148:3: note: in expansion of macro ‘dev_warn’
dev_warn(ext->dev,
^~~~~~~~
drivers/extcon/extcon-intel-cht-wc.c:152:2: note: here
case CHT_WC_USBSRC_TYPE_SDP:
^~~~
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Switch to use kasprintf() instead of open coded variant.
No functional change intended.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
When assign unions we need to supply non-scalar value, otherwise
static analyzer is not happy:
CHECK drivers/extcon/extcon.c
drivers/extcon/extcon.c:631:22: warning: cast to non-scalar
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Detailed description for this pull request:
1. Release locking when sending the connector state in extcon_sync()
- Previously, extcon used the spinlock before calling the notifier_call_chain
to prevent the scheduled out of task and to prevent the notification delay.
When spinlock is locked for sending the notification, deadlock issue
occured on the side of extcon consumer device. To fix this issue on extcon
consumer device, release locking when sending the connector state.
2. Fix minor issues of extcon provider driver
- extcon-intel-int3496.c uses 'linux/gpio/consumer.h' instead of 'linux/gpio.h'
- extcon-usbc-cors-ec.c adds SPDX license and fix the wrong license information
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=Iuyb
-----END PGP SIGNATURE-----
Merge tag 'extcon-next-for-4.19' of git://git.kernel.org/pub/scm/linux/kernel/git/chanwoo/extcon into char-misc-next
Chanwoo writes:
Update extcon for 4.19
Detailed description for this pull request:
1. Release locking when sending the connector state in extcon_sync()
- Previously, extcon used the spinlock before calling the notifier_call_chain
to prevent the scheduled out of task and to prevent the notification delay.
When spinlock is locked for sending the notification, deadlock issue
occured on the side of extcon consumer device. To fix this issue on extcon
consumer device, release locking when sending the connector state.
2. Fix minor issues of extcon provider driver
- extcon-intel-int3496.c uses 'linux/gpio/consumer.h' instead of 'linux/gpio.h'
- extcon-usbc-cors-ec.c adds SPDX license and fix the wrong license information
Previously, extcon used the spinlock before calling the notifier_call_chain
to prevent the scheduled out of task and to prevent the notification delay.
When spinlock is locked for sending the notification, deadlock issue
occured on the side of extcon consumer device. To fix this issue,
extcon consumer device should always use the work. it is always not
reasonable to use work.
To fix this issue on extcon consumer device, release locking when sending
the notification of connector state.
Fixes: ab11af049f ("extcon: Add the synchronization extcon APIs to support the notification")
Cc: stable@vger.kernel.org
Cc: Roger Quadros <rogerq@ti.com>
Cc: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
The license text is specifying "GPLv2" but the MODULE_LICENSE is set to
GPL which means GNU Public License v2 or later. When MODULE_LICENSE and
boiler plate does not match, go for boiler plate license.
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Since commit eca0f13c83 ("extcon: int3496: Ignore incorrect
IoRestriction for ID pin"), the driver doesn't use GPIOF_* flags
anymore. We can thus now drop the deprecated include file for GPIO and
use the new one.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Another driver turned up that is missing linux/mod_devicetable.h after
the device IDs are split out from linux/platform_device.h:
drivers/extcon/extcon-max3355.c:127:34: error: array type has incomplete element type 'struct of_device_id'
static const struct of_device_id max3355_match_table[] = {
Fixes: ac3167257b ("headers: separate linux/mod_devicetable.h from linux/platform_device.h")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
At over 4000 #includes, <linux/platform_device.h> is the 9th most
#included header file in the Linux kernel. It does not need
<linux/mod_devicetable.h>, so drop that header and explicitly add
<linux/mod_devicetable.h> to source files that need it.
4146 #include <linux/platform_device.h>
After this patch, there are 225 files that use <linux/mod_devicetable.h>,
for a reduction of around 3900 times that <linux/mod_devicetable.h>
does not have to be read & parsed.
225 #include <linux/mod_devicetable.h>
This patch was build-tested on 20 different arch-es.
It also makes these drivers SubmitChecklist#1 compliant.
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Reported-by: kbuild test robot <lkp@intel.com> # drivers/media/platform/vimc/
Reported-by: kbuild test robot <lkp@intel.com> # drivers/pinctrl/pinctrl-u300.c
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here is the big set of char/misc driver patches for 4.17-rc1.
There are a lot of little things in here, nothing huge, but all
important to the different hardware types involved:
- thunderbolt driver updates
- parport updates (people still care...)
- nvmem driver updates
- mei updates (as always)
- hwtracing driver updates
- hyperv driver updates
- extcon driver updates
- and a handfull of even smaller driver subsystem and individual
driver updates
All of these have been in linux-next with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWsShSQ8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ykNqwCfUbfvopswb1PesHCLABDBsFQChgoAniDa6pS9
kI8TN5MdLN85UU27Mkb6
=BzFR
-----END PGP SIGNATURE-----
Merge tag 'char-misc-4.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc updates from Greg KH:
"Here is the big set of char/misc driver patches for 4.17-rc1.
There are a lot of little things in here, nothing huge, but all
important to the different hardware types involved:
- thunderbolt driver updates
- parport updates (people still care...)
- nvmem driver updates
- mei updates (as always)
- hwtracing driver updates
- hyperv driver updates
- extcon driver updates
- ... and a handful of even smaller driver subsystem and individual
driver updates
All of these have been in linux-next with no reported issues"
* tag 'char-misc-4.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (149 commits)
hwtracing: Add HW tracing support menu
intel_th: Add ACPI glue layer
intel_th: Allow forcing host mode through drvdata
intel_th: Pick up irq number from resources
intel_th: Don't touch switch routing in host mode
intel_th: Use correct method of finding hub
intel_th: Add SPDX GPL-2.0 header to replace GPLv2 boilerplate
stm class: Make dummy's master/channel ranges configurable
stm class: Add SPDX GPL-2.0 header to replace GPLv2 boilerplate
MAINTAINERS: Bestow upon myself the care for drivers/hwtracing
hv: add SPDX license id to Kconfig
hv: add SPDX license to trace
Drivers: hv: vmbus: do not mark HV_PCIE as perf_device
Drivers: hv: vmbus: respect what we get from hv_get_synint_state()
/dev/mem: Avoid overwriting "err" in read_mem()
eeprom: at24: use SPDX identifier instead of GPL boiler-plate
eeprom: at24: simplify the i2c functionality checking
eeprom: at24: fix a line break
eeprom: at24: tweak newlines
eeprom: at24: refactor at24_probe()
...
The AXP288 BC1.2 charger detection / extcon code may seem like a strange
place to add code to control the USB role-switch on devices with an AXP288,
but there are 2 reasons to do this inside the axp288 extcon code:
1) On many devices the USB role is controlled by ACPI AML code, but the AML
code only switches between the host and none roles, because of Windows
not really using device mode. To make device mode work we need to toggle
between the none/device roles based on Vbus presence, and the axp288
extcon gets interrupts on Vbus insertion / removal.
2) In order for our BC1.2 charger detection to work properly the role
mux must be properly set to device mode before we do the detection.
Also note the Kconfig help-text / obsolete depends on USB_PHY which are
remnants from older never upstreamed code also controlling the mux from
the axp288 extcon code.
This commit also adds code to get notifications from the INT3496 extcon
device, which is used on some devices to notify the kernel about id-pin
changes instead of them being handled through AML code.
This fixes:
-Device mode not working on most CHT devices with an AXP288
-Host mode not working on devices with an INT3496 ACPI device
-Charger-type misdetection (always SDP) on devices with an INT3496 when the
USB role (always) gets initialized as host
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since we are not getting the GPIO from any platform data and global
GPIO numberspace, we simply get the named "extcon" GPIO directly from
the device. Cut away "active low" since GPIO descriptors already know
if the line is active high or low. Simplify a bit with a
struct device *dev helper variable in probe() and cut the complex
init() function.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
This moves the platform data settings from the platform data
struct and into the state container, saving some unnecessary
references and simplifying things a bit.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
[cw00.choi: Add FIXME comment of extcon_id]
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Nothing in the entire kernel #includes <linux/extcon/extcon-gpio.h>
so move the platform data declaration inside of the driver.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
The commit
70216fd937 ("extcon: int3496: Set the id pin to direction-input if necessary")
introduced a workaround for incorrect IoRestriction mode in ACPI table.
Now, when GPIO ACPI library does it in generic way, see the commit
1b2ca32ab0 ("gpiolib: acpi: Introduce NO_RESTRICTION quirk")
for the details, just set an appropriate quirk flag instead.
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Tested-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Sometimes (firmware bug?) the V5 boost GPIO is not configured as output
by the BIOS, leading to the 5V boost convertor being permanently on,
Explicitly set the direction and drv flags rather then inheriting them
from the firmware to fix this.
Fixes: 585cb239f4 ("extcon: intel-cht-wc: Disable external 5v boost ...")
Cc: stable@vger.kernel.org
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Since extcon property is not allowed in DT, extcon subsystem requires
another way to get extcon device. Lets try the simplest approach - get
edev by of_node.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Some other drivers may be waiting for our extcon to show-up, exiting their
probe methods with -EPROBE_DEFER until we show up.
These drivers will typically get the cable state directly after getting
the extcon, this commit changes the int3496 code to wait for the initial
processing of the id-pin to complete before exiting probe() with 0, which
will cause devices waiting on the defered probe to get reprobed.
This fixes a race where the initial work might still be running while other
drivers were already calling extcon_get_state().
Fixes: 2f556bdb9f ("extcon: int3496: Add Intel INT3496 ACPI ... driver")
Cc: stable@vger.kernel.org
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Redoing the charger type detection to give the usb-role-switch code time
to properly set the role-switch is no good for mainline, since the
usb-role-switch code is not yet in mainline (my bad, sorry).
Also once we've that code there are better ways to fix this which are
not prone to racing as doing a retry after 2 seconds is.
This reverts commit 50082c17bb1455acacd376ae30dff92f2e1addbd.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Make the axp288_pwr_up_down_info array const char * const, this leads
to the following section size changes:
.text 0x674 -> 0x664
.data 0x148 -> 0x0f0
.rodata 0x0b4 -> 0x114
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
According to the data sheets all the values not handled in the
switch-case are "reserved". Update the dev_warn message to reflect
this and set the cable-type to EXTCON_CHG_USB_SDP (so max 500mA
current draw) as safe default.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
The axp288 extcon code depends on other drivers to do things like mux the
data lines, enable/disable vbus based on the id-pin, etc.
Sometimes the BIOS has not set these things up correctly resulting in the
initial charger cable type detection giving a wrong result and we end up
not charging or charging at only 0.5A.
This commit starts a second charger-detection cycle a couple of seconds
after the first one finishes, giving the other drivers time to load and
do their thing.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
This is not used / set anywhere in the tree.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
platform_get_irq() can fail here and we must check its return value.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Extend the driver to notify host and device type cables and the presence
of power.
Signed-off-by: Benson Leung <bleung@chromium.org>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
The platform_get_irq() function returns negative if an error occurs.
zero or positive number on success. platform_get_irq() error checking
for zero is not correct.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
The variable "ret" will be set to an appropriate value a bit later.
Thus this patch omits the explicit initialization at the beginning.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
The variable "ret" will be set to an appropriate value a bit later.
Thus this patch omits the explicit initialization at the beginning.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Here is the big set of USB and PHY driver updates for 4.15-rc1.
There is the usual amount of gadget and xhci driver updates, along with
phy and chipidea enhancements. There's also a lot of SPDX tags and
license boilerplate cleanups as well, which provide some churn in the
diffstat.
Other major thing is the typec code that moved out of staging and into
the "real" part of the drivers/usb/ tree, which was nice to see happen.
All of these have been in linux-next with no reported issues for a
while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWgm/Vw8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+yktXwCdGgpInfOEvOGFd83EPDL7a1ncyc4AoM5wI8yl
1CeLipqVIN3IsMMJptvb
=zvDI
-----END PGP SIGNATURE-----
Merge tag 'usb-4.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB/PHY updates from Greg KH:
"Here is the big set of USB and PHY driver updates for 4.15-rc1.
There is the usual amount of gadget and xhci driver updates, along
with phy and chipidea enhancements. There's also a lot of SPDX tags
and license boilerplate cleanups as well, which provide some churn in
the diffstat.
Other major thing is the typec code that moved out of staging and into
the "real" part of the drivers/usb/ tree, which was nice to see
happen.
All of these have been in linux-next with no reported issues for a
while"
* tag 'usb-4.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (263 commits)
usb: gadget: f_fs: Fix use-after-free in ffs_free_inst
USB: usbfs: compute urb->actual_length for isochronous
usb: core: message: remember to reset 'ret' to 0 when necessary
USB: typec: Remove remaining redundant license text
USB: typec: add SPDX identifiers to some files
USB: renesas_usbhs: rcar?.h: add SPDX tags
USB: chipidea: ci_hdrc_tegra.c: add SPDX line
USB: host: xhci-debugfs: add SPDX lines
USB: add SPDX identifiers to all remaining Makefiles
usb: host: isp1362-hcd: remove a couple of redundant assignments
USB: adutux: remove redundant variable minor
usb: core: add a new usb_get_ptm_status() helper
usb: core: add a 'type' parameter to usb_get_status()
usb: core: introduce a new usb_get_std_status() helper
usb: core: rename usb_get_status() 'type' argument to 'recip'
usb: core: add Status Type definitions
USB: gadget: Remove redundant license text
USB: gadget: function: Remove redundant license text
USB: gadget: udc: Remove redundant license text
USB: gadget: legacy: Remove redundant license text
...
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
SmartDock uses ADC_RESERVED_ACC_3 (0x10) ADC ID type and provides following
features:
1. USB host with embedded USB hub (2-4 ports) for mice, keyboard, etc,
2. MHL for video output,
3. charging.
Tested with Unitek Y-2165 MHL+OTG Hub Smart Phone Dock.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Enabling power on VBUS micro-usb pin is required only when passive OTG
cable is connected. Initially OTG VBUS power control was planned to be
done in charger driver. However such information is not really available
from the extcon notifications, so VBUS power control has to be done
directly in MUIC driver, which has all information about the attached
accessory.
For example SmartDock is externally powered accessory, provides OTG
(USB HOST) functionality and use VBUS pin for charging a device battery,
so the VBUS charging pump should be disabled in such case.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
The variable "ret" is immediately reassigned by a following statement.
Thus omit the explicit initialisation at the beginning.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
The array extcon_info is read only, local to the source and does not
need to be in global scope, so make it static const.
Cleans up sparse warning:
symbol 'extcon_info' was not declared. Should it be static?
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
The extcon has two type of extcon devices as following.
- 'extcon provider deivce' adds new extcon device and detect the
state/properties of external connector. Also, it notifies the
state/properties to the extcon consumer device.
- 'extcon consumer device' gets the change state/properties
from extcon provider device.
Prior to that, include/linux/extcon.h contains all exported API for
both provider and consumer device driver. To clarify the meaning of
header file and to remove the wrong use-case on consumer device,
this patch separates into extcon.h and extcon-provider.h.
[Description for include/linux/{extcon.h|extcon-provider.h}]
- extcon.h includes the extcon API and data structure for extcon consumer
device driver. This header file contains the following APIs:
: Register/unregister the notifier to catch the change of extcon device
: Get the extcon device instance
: Get the extcon device name
: Get the state of each external connector
: Get the property value of each external connector
: Get the property capability of each external connector
- extcon-provider.h includes the extcon API and data structure for extcon
provider device driver. This header file contains the following APIs:
: Include 'include/linux/extcon.h'
: Allocate the memory for extcon device instance
: Register/unregister extcon device
: Set the state of each external connector
: Set the property value of each external connector
: Set the property capability of each external connector
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Acked-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Acked-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
Marek Szyprowski