/* * Copyright (C) 2000-2002 Mark Lord * Copyright (C) 2007 Bartlomiej Zolnierkiewicz * * May be copied or modified under the terms of the GNU General Public License * * Development of this chipset driver was funded * by the nice folks at National Semiconductor. * * Documentation: * Available from National Semiconductor */ #include #include #include #include #include #include #include #include #define DRV_NAME "sc1200" #define SC1200_REV_A 0x00 #define SC1200_REV_B1 0x01 #define SC1200_REV_B3 0x02 #define SC1200_REV_C1 0x03 #define SC1200_REV_D1 0x04 #define PCI_CLK_33 0x00 #define PCI_CLK_48 0x01 #define PCI_CLK_66 0x02 #define PCI_CLK_33A 0x03 static unsigned short sc1200_get_pci_clock (void) { unsigned char chip_id, silicon_revision; unsigned int pci_clock; /* * Check the silicon revision, as not all versions of the chip * have the register with the fast PCI bus timings. */ chip_id = inb (0x903c); silicon_revision = inb (0x903d); // Read the fast pci clock frequency if (chip_id == 0x04 && silicon_revision < SC1200_REV_B1) { pci_clock = PCI_CLK_33; } else { // check clock generator configuration (cfcc) // the clock is in bits 8 and 9 of this word pci_clock = inw (0x901e); pci_clock >>= 8; pci_clock &= 0x03; if (pci_clock == PCI_CLK_33A) pci_clock = PCI_CLK_33; } return pci_clock; } /* * Here are the standard PIO mode 0-4 timings for each "format". * Format-0 uses fast data reg timings, with slower command reg timings. * Format-1 uses fast timings for all registers, but won't work with all drives. */ static const unsigned int sc1200_pio_timings[4][5] = {{0x00009172, 0x00012171, 0x00020080, 0x00032010, 0x00040010}, // format0 33Mhz {0xd1329172, 0x71212171, 0x30200080, 0x20102010, 0x00100010}, // format1, 33Mhz {0xfaa3f4f3, 0xc23232b2, 0x513101c1, 0x31213121, 0x10211021}, // format1, 48Mhz {0xfff4fff4, 0xf35353d3, 0x814102f1, 0x42314231, 0x11311131}}; // format1, 66Mhz /* * After chip reset, the PIO timings are set to 0x00009172, which is not valid. */ //#define SC1200_BAD_PIO(timings) (((timings)&~0x80000000)==0x00009172) static void sc1200_tunepio(ide_drive_t *drive, u8 pio) { ide_hwif_t *hwif = drive->hwif; struct pci_dev *pdev = to_pci_dev(hwif->dev); unsigned int basereg = hwif->channel ? 0x50 : 0x40, format = 0; pci_read_config_dword(pdev, basereg + 4, &format); format = (format >> 31) & 1; if (format) format += sc1200_get_pci_clock(); pci_write_config_dword(pdev, basereg + ((drive->dn & 1) << 3), sc1200_pio_timings[format][pio]); } /* * The SC1200 specifies that two drives sharing a cable cannot mix * UDMA/MDMA. It has to be one or the other, for the pair, though * different timings can still be chosen for each drive. We could * set the appropriate timing bits on the fly, but that might be * a bit confusing. So, for now we statically handle this requirement * by looking at our mate drive to see what it is capable of, before * choosing a mode for our own drive. */ static u8 sc1200_udma_filter(ide_drive_t *drive) { ide_hwif_t *hwif = drive->hwif; ide_drive_t *mate = ide_get_pair_dev(drive); u16 *mateid; u8 mask = hwif->ultra_mask; if (mate == NULL) goto out; mateid = mate->id; if (ata_id_has_dma(mateid) && __ide_dma_bad_drive(mate) == 0) { if ((mateid[ATA_ID_FIELD_VALID] & 4) && (mateid[ATA_ID_UDMA_MODES] & 7)) goto out; if ((mateid[ATA_ID_FIELD_VALID] & 2) && (mateid[ATA_ID_MWDMA_MODES] & 7)) mask = 0; } out: return mask; } static void sc1200_set_dma_mode(ide_drive_t *drive, const u8 mode) { ide_hwif_t *hwif = drive->hwif; struct pci_dev *dev = to_pci_dev(hwif->dev); unsigned int reg, timings; unsigned short pci_clock; unsigned int basereg = hwif->channel ? 0x50 : 0x40; static const u32 udma_timing[3][3] = { { 0x00921250, 0x00911140, 0x00911030 }, { 0x00932470, 0x00922260, 0x00922140 }, { 0x009436a1, 0x00933481, 0x00923261 }, }; static const u32 mwdma_timing[3][3] = { { 0x00077771, 0x00012121, 0x00002020 }, { 0x000bbbb2, 0x00024241, 0x00013131 }, { 0x000ffff3, 0x00035352, 0x00015151 }, }; pci_clock = sc1200_get_pci_clock(); /* * Note that each DMA mode has several timings associated with it. * The correct timing depends on the fast PCI clock freq. */ if (mode >= XFER_UDMA_0) timings = udma_timing[pci_clock][mode - XFER_UDMA_0]; else timings = mwdma_timing[pci_clock][mode - XFER_MW_DMA_0]; if ((drive->dn & 1) == 0) { pci_read_config_dword(dev, basereg + 4, ®); timings |= reg & 0x80000000; /* preserve PIO format bit */ pci_write_config_dword(dev, basereg + 4, timings); } else pci_write_config_dword(dev, basereg + 12, timings); } /* Replacement for the standard ide_dma_end action in * dma_proc. * * returns 1 on error, 0 otherwise */ static int sc1200_dma_end(ide_drive_t *drive) { ide_hwif_t *hwif = drive->hwif; unsigned long dma_base = hwif->dma_base; u8 dma_stat; dma_stat = inb(dma_base+2); /* get DMA status */ if (!(dma_stat & 4)) printk(" ide_dma_end dma_stat=%0x err=%x newerr=%x\n", dma_stat, ((dma_stat&7)!=4), ((dma_stat&2)==2)); outb(dma_stat|0x1b, dma_base+2); /* clear the INTR & ERROR bits */ outb(inb(dma_base)&~1, dma_base); /* !! DO THIS HERE !! stop DMA */ drive->waiting_for_dma = 0; return (dma_stat & 7) != 4; /* verify good DMA status */ } /* * sc1200_set_pio_mode() handles setting of PIO modes * for both the chipset and drive. * * All existing BIOSs for this chipset guarantee that all drives * will have valid default PIO timings set up before we get here. */ static void sc1200_set_pio_mode(ide_drive_t *drive, const u8 pio) { ide_hwif_t *hwif = drive->hwif; int mode = -1; /* * bad abuse of ->set_pio_mode interface */ switch (pio) { case 200: mode = XFER_UDMA_0; break; case 201: mode = XFER_UDMA_1; break; case 202: mode = XFER_UDMA_2; break; case 100: mode = XFER_MW_DMA_0; break; case 101: mode = XFER_MW_DMA_1; break; case 102: mode = XFER_MW_DMA_2; break; } if (mode != -1) { printk("SC1200: %s: changing (U)DMA mode\n", drive->name); ide_dma_off_quietly(drive); if (ide_set_dma_mode(drive, mode) == 0 && (drive->dev_flags & IDE_DFLAG_USING_DMA)) hwif->dma_ops->dma_host_set(drive, 1); return; } sc1200_tunepio(drive, pio); } #ifdef CONFIG_PM struct sc1200_saved_state { u32 regs[8]; }; static int sc1200_suspend (struct pci_dev *dev, pm_message_t state) { printk("SC1200: suspend(%u)\n", state.event); /* * we only save state when going from full power to less */ if (state.event == PM_EVENT_ON) { struct ide_host *host = pci_get_drvdata(dev); struct sc1200_saved_state *ss = host->host_priv; unsigned int r; /* * save timing registers * (this may be unnecessary if BIOS also does it) */ for (r = 0; r < 8; r++) pci_read_config_dword(dev, 0x40 + r * 4, &ss->regs[r]); } pci_disable_device(dev); pci_set_power_state(dev, pci_choose_state(dev, state)); return 0; } static int sc1200_resume (struct pci_dev *dev) { struct ide_host *host = pci_get_drvdata(dev); struct sc1200_saved_state *ss = host->host_priv; unsigned int r; int i; i = pci_enable_device(dev); if (i) return i; /* * restore timing registers * (this may be unnecessary if BIOS also does it) */ for (r = 0; r < 8; r++) pci_write_config_dword(dev, 0x40 + r * 4, ss->regs[r]); return 0; } #endif static const struct ide_port_ops sc1200_port_ops = { .set_pio_mode = sc1200_set_pio_mode, .set_dma_mode = sc1200_set_dma_mode, .udma_filter = sc1200_udma_filter, }; static const struct ide_dma_ops sc1200_dma_ops = { .dma_host_set = ide_dma_host_set, .dma_setup = ide_dma_setup, .dma_start = ide_dma_start, .dma_end = sc1200_dma_end, .dma_test_irq = ide_dma_test_irq, .dma_lost_irq = ide_dma_lost_irq, .dma_timer_expiry = ide_dma_sff_timer_expiry, .dma_sff_read_status = ide_dma_sff_read_status, }; static const struct ide_port_info sc1200_chipset __devinitdata = { .name = DRV_NAME, .port_ops = &sc1200_port_ops, .dma_ops = &sc1200_dma_ops, .host_flags = IDE_HFLAG_SERIALIZE | IDE_HFLAG_POST_SET_MODE | IDE_HFLAG_ABUSE_DMA_MODES, .pio_mask = ATA_PIO4, .mwdma_mask = ATA_MWDMA2, .udma_mask = ATA_UDMA2, }; static int __devinit sc1200_init_one(struct pci_dev *dev, const struct pci_device_id *id) { struct sc1200_saved_state *ss = NULL; int rc; #ifdef CONFIG_PM ss = kmalloc(sizeof(*ss), GFP_KERNEL); if (ss == NULL) return -ENOMEM; #endif rc = ide_pci_init_one(dev, &sc1200_chipset, ss); if (rc) kfree(ss); return rc; } static const struct pci_device_id sc1200_pci_tbl[] = { { PCI_VDEVICE(NS, PCI_DEVICE_ID_NS_SCx200_IDE), 0}, { 0, }, }; MODULE_DEVICE_TABLE(pci, sc1200_pci_tbl); static struct pci_driver sc1200_pci_driver = { .name = "SC1200_IDE", .id_table = sc1200_pci_tbl, .probe = sc1200_init_one, .remove = ide_pci_remove, #ifdef CONFIG_PM .suspend = sc1200_suspend, .resume = sc1200_resume, #endif }; static int __init sc1200_ide_init(void) { return ide_pci_register_driver(&sc1200_pci_driver); } static void __exit sc1200_ide_exit(void) { pci_unregister_driver(&sc1200_pci_driver); } module_init(sc1200_ide_init); module_exit(sc1200_ide_exit); MODULE_AUTHOR("Mark Lord"); MODULE_DESCRIPTION("PCI driver module for NS SC1200 IDE"); MODULE_LICENSE("GPL");