/*
 * Critical Link MityOMAP-L138 SoM
 *
 * Copyright (C) 2010 Critical Link LLC - http://www.criticallink.com
 *
 * This file is licensed under the terms of the GNU General Public License
 * version 2. This program is licensed "as is" without any warranty of
 * any kind, whether express or implied.
 */

#include <linux/kernel.h>
#include <linux/init.h>
#include <linux/console.h>
#include <linux/platform_device.h>
#include <linux/mtd/partitions.h>

#include <asm/mach-types.h>
#include <asm/mach/arch.h>
#include <mach/common.h>
#include <mach/cp_intc.h>
#include <mach/da8xx.h>
#include <mach/nand.h>
#include <mach/mux.h>

#define MITYOMAPL138_PHY_MASK		0x08 /* hardcoded for now */
#define MITYOMAPL138_MDIO_FREQUENCY	(2200000) /* PHY bus frequency */

/*
 * MityDSP-L138 includes a 256 MByte large-page NAND flash
 * (128K blocks).
 */
struct mtd_partition mityomapl138_nandflash_partition[] = {
	{
		.name		= "rootfs",
		.offset		= 0,
		.size		= SZ_128M,
		.mask_flags	= 0, /* MTD_WRITEABLE, */
	},
	{
		.name		= "homefs",
		.offset		= MTDPART_OFS_APPEND,
		.size		= MTDPART_SIZ_FULL,
		.mask_flags	= 0,
	},
};

static struct davinci_nand_pdata mityomapl138_nandflash_data = {
	.parts		= mityomapl138_nandflash_partition,
	.nr_parts	= ARRAY_SIZE(mityomapl138_nandflash_partition),
	.ecc_mode	= NAND_ECC_HW,
	.options	= NAND_USE_FLASH_BBT | NAND_BUSWIDTH_16,
	.ecc_bits	= 1, /* 4 bit mode is not supported with 16 bit NAND */
};

static struct resource mityomapl138_nandflash_resource[] = {
	{
		.start	= DA8XX_AEMIF_CS3_BASE,
		.end	= DA8XX_AEMIF_CS3_BASE + SZ_512K + 2 * SZ_1K - 1,
		.flags	= IORESOURCE_MEM,
	},
	{
		.start	= DA8XX_AEMIF_CTL_BASE,
		.end	= DA8XX_AEMIF_CTL_BASE + SZ_32K - 1,
		.flags	= IORESOURCE_MEM,
	},
};

static struct platform_device mityomapl138_nandflash_device = {
	.name		= "davinci_nand",
	.id		= 0,
	.dev		= {
		.platform_data	= &mityomapl138_nandflash_data,
	},
	.num_resources	= ARRAY_SIZE(mityomapl138_nandflash_resource),
	.resource	= mityomapl138_nandflash_resource,
};

static struct platform_device *mityomapl138_devices[] __initdata = {
	&mityomapl138_nandflash_device,
};

static void __init mityomapl138_setup_nand(void)
{
	platform_add_devices(mityomapl138_devices,
				 ARRAY_SIZE(mityomapl138_devices));
}

static struct davinci_uart_config mityomapl138_uart_config __initdata = {
	.enabled_uarts = 0x7,
};

static const short mityomap_mii_pins[] = {
	DA850_MII_TXEN, DA850_MII_TXCLK, DA850_MII_COL, DA850_MII_TXD_3,
	DA850_MII_TXD_2, DA850_MII_TXD_1, DA850_MII_TXD_0, DA850_MII_RXER,
	DA850_MII_CRS, DA850_MII_RXCLK, DA850_MII_RXDV, DA850_MII_RXD_3,
	DA850_MII_RXD_2, DA850_MII_RXD_1, DA850_MII_RXD_0, DA850_MDIO_CLK,
	DA850_MDIO_D,
	-1
};

static const short mityomap_rmii_pins[] = {
	DA850_RMII_TXD_0, DA850_RMII_TXD_1, DA850_RMII_TXEN,
	DA850_RMII_CRS_DV, DA850_RMII_RXD_0, DA850_RMII_RXD_1,
	DA850_RMII_RXER, DA850_RMII_MHZ_50_CLK, DA850_MDIO_CLK,
	DA850_MDIO_D,
	-1
};

static void __init mityomapl138_config_emac(void)
{
	void __iomem *cfg_chip3_base;
	int ret;
	u32 val;
	struct davinci_soc_info *soc_info = &davinci_soc_info;

	soc_info->emac_pdata->rmii_en = 0; /* hardcoded for now */

	cfg_chip3_base = DA8XX_SYSCFG0_VIRT(DA8XX_CFGCHIP3_REG);
	val = __raw_readl(cfg_chip3_base);

	if (soc_info->emac_pdata->rmii_en) {
		val |= BIT(8);
		ret = davinci_cfg_reg_list(mityomap_rmii_pins);
		pr_info("RMII PHY configured\n");
	} else {
		val &= ~BIT(8);
		ret = davinci_cfg_reg_list(mityomap_mii_pins);
		pr_info("MII PHY configured\n");
	}

	if (ret) {
		pr_warning("mii/rmii mux setup failed: %d\n", ret);
		return;
	}

	/* configure the CFGCHIP3 register for RMII or MII */
	__raw_writel(val, cfg_chip3_base);

	soc_info->emac_pdata->phy_mask = MITYOMAPL138_PHY_MASK;
	pr_debug("setting phy_mask to %x\n", soc_info->emac_pdata->phy_mask);
	soc_info->emac_pdata->mdio_max_freq = MITYOMAPL138_MDIO_FREQUENCY;

	ret = da8xx_register_emac();
	if (ret)
		pr_warning("emac registration failed: %d\n", ret);
}

static struct davinci_pm_config da850_pm_pdata = {
	.sleepcount = 128,
};

static struct platform_device da850_pm_device = {
	.name	= "pm-davinci",
	.dev = {
		.platform_data  = &da850_pm_pdata,
	},
	.id	= -1,
};

static void __init mityomapl138_init(void)
{
	int ret;

	/* for now, no special EDMA channels are reserved */
	ret = da850_register_edma(NULL);
	if (ret)
		pr_warning("edma registration failed: %d\n", ret);

	ret = da8xx_register_watchdog();
	if (ret)
		pr_warning("watchdog registration failed: %d\n", ret);

	davinci_serial_init(&mityomapl138_uart_config);

	mityomapl138_setup_nand();

	mityomapl138_config_emac();

	ret = da8xx_register_rtc();
	if (ret)
		pr_warning("rtc setup failed: %d\n", ret);

	ret = da850_register_cpufreq("pll0_sysclk3");
	if (ret)
		pr_warning("cpufreq registration failed: %d\n", ret);

	ret = da8xx_register_cpuidle();
	if (ret)
		pr_warning("cpuidle registration failed: %d\n", ret);

	ret = da850_register_pm(&da850_pm_device);
	if (ret)
		pr_warning("da850_evm_init: suspend registration failed: %d\n",
				ret);
}

#ifdef CONFIG_SERIAL_8250_CONSOLE
static int __init mityomapl138_console_init(void)
{
	if (!machine_is_mityomapl138())
		return 0;

	return add_preferred_console("ttyS", 1, "115200");
}
console_initcall(mityomapl138_console_init);
#endif

static void __init mityomapl138_map_io(void)
{
	da850_init();
}

MACHINE_START(MITYOMAPL138, "MityDSP-L138/MityARM-1808")
	.phys_io	= IO_PHYS,
	.io_pg_offst	= (__IO_ADDRESS(IO_PHYS) >> 18) & 0xfffc,
	.boot_params	= (DA8XX_DDR_BASE + 0x100),
	.map_io		= mityomapl138_map_io,
	.init_irq	= cp_intc_init,
	.timer		= &davinci_timer,
	.init_machine	= mityomapl138_init,
MACHINE_END