linux/drivers/net/irda/Kconfig

405 lines
14 KiB
Plaintext

menu "Infrared-port device drivers"
depends on IRDA!=n
comment "SIR device drivers"
config IRTTY_SIR
tristate "IrTTY (uses Linux serial driver)"
depends on IRDA && TTY
help
Say Y here if you want to build support for the IrTTY line
discipline. To compile it as a module, choose M here: the module
will be called irtty-sir. IrTTY makes it possible to use Linux's
own serial driver for all IrDA ports that are 16550 compatible.
Most IrDA chips are 16550 compatible so you should probably say Y
to this option. Using IrTTY will however limit the speed of the
connection to 115200 bps (IrDA SIR mode).
If unsure, say Y.
config BFIN_SIR
tristate "Blackfin SIR on UART"
depends on BLACKFIN && IRDA
default n
help
Say Y here if your want to enable SIR function on Blackfin UART
devices.
To activate this driver you can start irattach like:
"irattach irda0 -s"
Saying M, it will be built as a module named bfin_sir.
Note that you need to turn off one of the serial drivers for SIR
to use that UART.
config BFIN_SIR0
bool "Blackfin SIR on UART0"
depends on BFIN_SIR && !SERIAL_BFIN_UART0
config BFIN_SIR1
bool "Blackfin SIR on UART1"
depends on BFIN_SIR && !SERIAL_BFIN_UART1 && (!BF531 && !BF532 && !BF533 && !BF561)
config BFIN_SIR2
bool "Blackfin SIR on UART2"
depends on BFIN_SIR && !SERIAL_BFIN_UART2 && (BF54x || BF538 || BF539)
config BFIN_SIR3
bool "Blackfin SIR on UART3"
depends on BFIN_SIR && !SERIAL_BFIN_UART3 && (BF54x)
choice
prompt "SIR Mode"
depends on BFIN_SIR
default SIR_BFIN_DMA
config SIR_BFIN_DMA
bool "DMA mode"
depends on !DMA_UNCACHED_NONE
config SIR_BFIN_PIO
bool "PIO mode"
endchoice
config SH_SIR
tristate "SuperH SIR on UART"
depends on IRDA && SUPERH && \
(CPU_SUBTYPE_SH7722 || CPU_SUBTYPE_SH7723 || \
CPU_SUBTYPE_SH7724)
default n
help
Say Y here if your want to enable SIR function on SuperH UART
devices.
comment "Dongle support"
config DONGLE
bool "Serial dongle support"
depends on IRTTY_SIR
help
Say Y here if you have an infrared device that connects to your
computer's serial port. These devices are called dongles. Then say Y
or M to the driver for your particular dongle below.
Note that the answer to this question won't directly affect the
kernel: saying N will just cause the configurator to skip all
the questions about serial dongles.
config ESI_DONGLE
tristate "ESI JetEye PC dongle"
depends on IRTTY_SIR && DONGLE && IRDA
help
Say Y here if you want to build support for the Extended Systems
JetEye PC dongle. To compile it as a module, choose M here. The ESI
dongle attaches to the normal 9-pin serial port connector, and can
currently only be used by IrTTY. To activate support for ESI
dongles you will have to start irattach like this:
"irattach -d esi".
config ACTISYS_DONGLE
tristate "ACTiSYS IR-220L and IR220L+ dongle"
depends on IRTTY_SIR && DONGLE && IRDA
help
Say Y here if you want to build support for the ACTiSYS IR-220L and
IR220L+ dongles. To compile it as a module, choose M here. The
ACTiSYS dongles attaches to the normal 9-pin serial port connector,
and can currently only be used by IrTTY. To activate support for
ACTiSYS dongles you will have to start irattach like this:
"irattach -d actisys" or "irattach -d actisys+".
config TEKRAM_DONGLE
tristate "Tekram IrMate 210B dongle"
depends on IRTTY_SIR && DONGLE && IRDA
help
Say Y here if you want to build support for the Tekram IrMate 210B
dongle. To compile it as a module, choose M here. The Tekram dongle
attaches to the normal 9-pin serial port connector, and can
currently only be used by IrTTY. To activate support for Tekram
dongles you will have to start irattach like this:
"irattach -d tekram".
config TOIM3232_DONGLE
tristate "TOIM3232 IrDa dongle"
depends on IRTTY_SIR && DONGLE && IRDA
help
Say Y here if you want to build support for the Vishay/Temic
TOIM3232 and TOIM4232 based dongles.
To compile it as a module, choose M here.
config LITELINK_DONGLE
tristate "Parallax LiteLink dongle"
depends on IRTTY_SIR && DONGLE && IRDA
help
Say Y here if you want to build support for the Parallax Litelink
dongle. To compile it as a module, choose M here. The Parallax
dongle attaches to the normal 9-pin serial port connector, and can
currently only be used by IrTTY. To activate support for Parallax
dongles you will have to start irattach like this:
"irattach -d litelink".
config MA600_DONGLE
tristate "Mobile Action MA600 dongle"
depends on IRTTY_SIR && DONGLE && IRDA
help
Say Y here if you want to build support for the Mobile Action MA600
dongle. To compile it as a module, choose M here. The MA600 dongle
attaches to the normal 9-pin serial port connector, and can
currently only be used by IrTTY. The driver should also support
the MA620 USB version of the dongle, if the integrated USB-to-RS232
converter is supported by usbserial. To activate support for
MA600 dongle you will have to start irattach like this:
"irattach -d ma600".
config GIRBIL_DONGLE
tristate "Greenwich GIrBIL dongle"
depends on IRTTY_SIR && DONGLE && IRDA
help
Say Y here if you want to build support for the Greenwich GIrBIL
dongle. If you want to compile it as a module, choose M here.
The Greenwich dongle attaches to the normal 9-pin serial port
connector, and can currently only be used by IrTTY. To activate
support for Greenwich dongles you will have to start irattach
like this: "irattach -d girbil".
config MCP2120_DONGLE
tristate "Microchip MCP2120"
depends on IRTTY_SIR && DONGLE && IRDA
help
Say Y here if you want to build support for the Microchip MCP2120
dongle. If you want to compile it as a module, choose M here.
The MCP2120 dongle attaches to the normal 9-pin serial port
connector, and can currently only be used by IrTTY. To activate
support for MCP2120 dongles you will have to start irattach
like this: "irattach -d mcp2120".
You must build this dongle yourself. For more information see:
<http://www.eyetap.org/~tangf/irda_sir_linux.html>
config OLD_BELKIN_DONGLE
tristate "Old Belkin dongle"
depends on IRTTY_SIR && DONGLE && IRDA
help
Say Y here if you want to build support for the Adaptec Airport 1000
and 2000 dongles. If you want to compile it as a module, choose
M here. Some information is contained in the comments
at the top of <file:drivers/net/irda/old_belkin-sir.c>.
config ACT200L_DONGLE
tristate "ACTiSYS IR-200L dongle"
depends on IRTTY_SIR && DONGLE && IRDA
help
Say Y here if you want to build support for the ACTiSYS IR-200L
dongle. If you want to compile it as a module, choose M here.
The ACTiSYS IR-200L dongle attaches to the normal 9-pin serial
port connector, and can currently only be used by IrTTY.
To activate support for ACTiSYS IR-200L dongle you will have to
start irattach like this: "irattach -d act200l".
config KINGSUN_DONGLE
tristate "KingSun/DonShine DS-620 IrDA-USB dongle"
depends on IRDA && USB
help
Say Y or M here if you want to build support for the KingSun/DonShine
DS-620 IrDA-USB bridge device driver.
This USB bridge does not conform to the IrDA-USB device class
specification, and therefore needs its own specific driver. This
dongle supports SIR speed only (9600 bps).
To compile it as a module, choose M here: the module will be called
kingsun-sir.
config KSDAZZLE_DONGLE
tristate "KingSun Dazzle IrDA-USB dongle"
depends on IRDA && USB
help
Say Y or M here if you want to build support for the KingSun Dazzle
IrDA-USB bridge device driver.
This USB bridge does not conform to the IrDA-USB device class
specification, and therefore needs its own specific driver. This
dongle supports SIR speeds only (9600 through 115200 bps).
To compile it as a module, choose M here: the module will be called
ksdazzle-sir.
config KS959_DONGLE
tristate "KingSun KS-959 IrDA-USB dongle"
depends on IRDA && USB
help
Say Y or M here if you want to build support for the KingSun KS-959
IrDA-USB bridge device driver.
This USB bridge does not conform to the IrDA-USB device class
specification, and therefore needs its own specific driver. This
dongle supports SIR speeds only (9600 through 57600 bps).
To compile it as a module, choose M here: the module will be called
ks959-sir.
comment "FIR device drivers"
config USB_IRDA
tristate "IrDA USB dongles"
depends on IRDA && USB
select FW_LOADER
---help---
Say Y here if you want to build support for the USB IrDA FIR Dongle
device driver. To compile it as a module, choose M here: the module
will be called irda-usb. IrDA-USB support the various IrDA USB
dongles available and most of their peculiarities. Those dongles
plug in the USB port of your computer, are plug and play, and
support SIR and FIR (4Mbps) speeds. On the other hand, those
dongles tend to be less efficient than a FIR chipset.
Please note that the driver is still experimental. And of course,
you will need both USB and IrDA support in your kernel...
config SIGMATEL_FIR
tristate "SigmaTel STIr4200 bridge"
depends on IRDA && USB
select CRC32
---help---
Say Y here if you want to build support for the SigmaTel STIr4200
USB IrDA FIR bridge device driver.
USB bridge based on the SigmaTel STIr4200 don't conform to the
IrDA-USB device class specification, and therefore need their
own specific driver. Those dongles support SIR and FIR (4Mbps)
speeds.
To compile it as a module, choose M here: the module will be called
stir4200.
config NSC_FIR
tristate "NSC PC87108/PC87338"
depends on IRDA && ISA_DMA_API
help
Say Y here if you want to build support for the NSC PC87108 and
PC87338 IrDA chipsets. This driver supports SIR,
MIR and FIR (4Mbps) speeds.
To compile it as a module, choose M here: the module will be called
nsc-ircc.
config WINBOND_FIR
tristate "Winbond W83977AF (IR)"
depends on IRDA && ISA_DMA_API
help
Say Y here if you want to build IrDA support for the Winbond
W83977AF super-io chipset. This driver should be used for the IrDA
chipset in the Corel NetWinder. The driver supports SIR, MIR and
FIR (4Mbps) speeds.
To compile it as a module, choose M here: the module will be called
w83977af_ir.
config TOSHIBA_FIR
tristate "Toshiba Type-O IR Port"
depends on IRDA && PCI && !64BIT && VIRT_TO_BUS
help
Say Y here if you want to build support for the Toshiba Type-O IR
and Donau oboe chipsets. These chipsets are used by the Toshiba
Libretto 100/110CT, Tecra 8100, Portege 7020 and many more laptops.
To compile it as a module, choose M here: the module will be called
donauboe.
config AU1000_FIR
tristate "Alchemy IrDA SIR/FIR"
depends on IRDA && MIPS_ALCHEMY
help
Say Y/M here to build support the IrDA peripheral on the
Alchemy Au1000 and Au1100 SoCs.
Say M to build a module; it will be called au1k_ir.ko
config SMC_IRCC_FIR
tristate "SMSC IrCC"
depends on IRDA && ISA_DMA_API
help
Say Y here if you want to build support for the SMC Infrared
Communications Controller. It is used in a wide variety of
laptops (Fujitsu, Sony, Compaq and some Toshiba).
To compile it as a module, choose M here: the module will be called
smsc-ircc2.o.
config ALI_FIR
tristate "ALi M5123 FIR"
depends on IRDA && ISA_DMA_API
help
Say Y here if you want to build support for the ALi M5123 FIR
Controller. The ALi M5123 FIR Controller is embedded in ALi M1543C,
M1535, M1535D, M1535+, M1535D South Bridge. This driver supports
SIR, MIR and FIR (4Mbps) speeds.
To compile it as a module, choose M here: the module will be called
ali-ircc.
config VLSI_FIR
tristate "VLSI 82C147 SIR/MIR/FIR"
depends on IRDA && PCI
help
Say Y here if you want to build support for the VLSI 82C147
PCI-IrDA Controller. This controller is used by the HP OmniBook 800
and 5500 notebooks. The driver provides support for SIR, MIR and
FIR (4Mbps) speeds.
To compile it as a module, choose M here: the module will be called
vlsi_ir.
config SA1100_FIR
tristate "SA1100 Internal IR"
depends on ARCH_SA1100 && IRDA && DMA_SA11X0
config VIA_FIR
tristate "VIA VT8231/VT1211 SIR/MIR/FIR"
depends on IRDA && ISA_DMA_API
help
Say Y here if you want to build support for the VIA VT8231
and VIA VT1211 IrDA controllers, found on the motherboards using
those VIA chipsets. To use this controller, you will need
to plug a specific 5 pins FIR IrDA dongle in the specific
motherboard connector. The driver provides support for SIR, MIR
and FIR (4Mbps) speeds.
You will need to specify the 'dongle_id' module parameter to
indicate the FIR dongle attached to the controller.
To compile it as a module, choose M here: the module will be called
via-ircc.
config PXA_FICP
tristate "Intel PXA2xx Internal FICP"
depends on ARCH_PXA && IRDA
help
Say Y or M here if you want to build support for the PXA2xx
built-in IRDA interface which can support both SIR and FIR.
This driver relies on platform specific helper routines so
available capabilities may vary from one PXA2xx target to
another.
config MCS_FIR
tristate "MosChip MCS7780 IrDA-USB dongle"
depends on IRDA && USB
select CRC32
help
Say Y or M here if you want to build support for the MosChip
MCS7780 IrDA-USB bridge device driver.
USB bridge based on the MosChip MCS7780 don't conform to the
IrDA-USB device class specification, and therefore need their
own specific driver. Those dongles support SIR and FIR (4Mbps)
speeds.
To compile it as a module, choose M here: the module will be called
mcs7780.
config SH_IRDA
tristate "SuperH IrDA driver"
depends on IRDA && ARCH_SHMOBILE
help
Say Y here if your want to enable SuperH IrDA devices.
endmenu