Here's the big USB pull request for 3.14-rc1 Lots of little things all over the place, and the usual USB gadget updates, and XHCI fixes (some for an issue reported by a lot of people.) USB PHY updates as well as chipidea updates and fixes. All of these have been in the linux-next tree with no reported issues. Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> -----BEGIN PGP SIGNATURE----- Version: GnuPG v2.0.22 (GNU/Linux) iEYEABECAAYFAlLdjwIACgkQMUfUDdst+ylBIQCgkRoR8lJc0L5lZ3fugIJL4IzZ j6AAn0nBLP6VI0cvUEi3TcrPTzv4MEuL =Yb+I -----END PGP SIGNATURE----- Merge tag 'usb-3.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb Pull USB updates from Greg KH: "Here's the big USB pull request for 3.14-rc1 Lots of little things all over the place, and the usual USB gadget updates, and XHCI fixes (some for an issue reported by a lot of people). USB PHY updates as well as chipidea updates and fixes. All of these have been in the linux-next tree with no reported issues" * tag 'usb-3.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (318 commits) usb: chipidea: udc: using MultO at TD as real mult value for ISO-TX usb: chipidea: need to mask INT_STATUS when write otgsc usb: chipidea: put hw_phymode_configure before ci_usb_phy_init usb: chipidea: Fix Internal error: : 808 [#1] ARM related to STS flag usb: chipidea: imx: set CI_HDRC_IMX28_WRITE_FIX for imx28 usb: chipidea: add freescale imx28 special write register method usb: ehci: add freescale imx28 special write register method usb: core: check for valid id_table when using the RefId feature usb: cdc-wdm: resp_count can be 0 even if WDM_READ is set usb: core: bail out if user gives an unknown RefId when using new_id usb: core: allow a reference device for new_id usb: core: add sanity checks when using bInterfaceClass with new_id USB: image: correct spelling mistake in comment USB: c67x00: correct spelling mistakes in comments usb: delete non-required instances of include <linux/init.h> usb:hub set hub->change_bits when over-current happens Revert "usb: chipidea: imx: set CI_HDRC_IMX28_WRITE_FIX for imx28" xhci: Set scatter-gather limit to avoid failed block writes. xhci: Avoid infinite loop when sg urb requires too many trbs usb: gadget: remove unused variable in gr_queue_int() ... |
||
---|---|---|
.. | ||
Kconfig | ||
Makefile | ||
README | ||
TODO | ||
ozappif.h | ||
ozcdev.c | ||
ozcdev.h | ||
ozdbg.h | ||
ozeltbuf.c | ||
ozeltbuf.h | ||
ozhcd.c | ||
ozhcd.h | ||
ozmain.c | ||
ozpd.c | ||
ozpd.h | ||
ozproto.c | ||
ozproto.h | ||
ozprotocol.h | ||
ozurbparanoia.c | ||
ozurbparanoia.h | ||
ozusbif.h | ||
ozusbsvc.c | ||
ozusbsvc.h | ||
ozusbsvc1.c |
README
OZWPAN USB Host Controller Driver --------------------------------- This driver is a USB HCD driver that does not have an associated a physical device but instead uses Wi-Fi to communicate with the wireless peripheral. The USB requests are converted into a layer 2 network protocol and transmitted on the network using an ethertype (0x892e) regestered to Ozmo Device Inc. This driver is compatible with existing wireless devices that use Ozmo Devices technology. To operate the driver must be bound to a suitable network interface. This can be done when the module is loaded (specifying the name of the network interface as a parameter - e.g. 'insmod ozwpan g_net_dev=go0') or can be bound after loading using an ioctl call. See the ozappif.h file and the ioctls OZ_IOCTL_ADD_BINDING and OZ_IOCTL_REMOVE_BINDING. The devices connect to the host use Wi-Fi Direct so a network card that supports Wi-Fi direct is required. A recent version (0.8.x or later) version of the wpa_supplicant can be used to setup the network interface to create a persistent autonomous group (for older pre-WFD peripherals) or put in a listen state to allow group negotiation to occur for more recent devices that support WFD. The protocol used over the network does not directly mimic the USB bus transactions as this would be rather busy and inefficient. Instead the chapter 9 requests are converted into a request/response pair of messages. (See ozprotocol.h for data structures used in the protocol).