2fc75da0c5
This patch converts the drivers in drivers/ata/* to use module_pci_driver() macro which makes the code smaller and a bit simpler. Signed-off-by: Axel Lin <axel.lin@gmail.com> Cc: Alan Cox <alan@linux.intel.com> Cc: Jeff Garzik <jgarzik@pobox.com> Cc: Mikael Pettersson <mikpe@it.uu.se> Cc: Mark Lord <kernel@teksavvy.com> Cc: Jeremy Higdon <jeremy@sgi.com> Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
382 lines
9.3 KiB
C
382 lines
9.3 KiB
C
/*
|
|
* pata_sl82c105.c - SL82C105 PATA for new ATA layer
|
|
* (C) 2005 Red Hat Inc
|
|
* (C) 2011 Bartlomiej Zolnierkiewicz
|
|
*
|
|
* Based in part on linux/drivers/ide/pci/sl82c105.c
|
|
* SL82C105/Winbond 553 IDE driver
|
|
*
|
|
* and in part on the documentation and errata sheet
|
|
*
|
|
*
|
|
* Note: The controller like many controllers has shared timings for
|
|
* PIO and DMA. We thus flip to the DMA timings in dma_start and flip back
|
|
* in the dma_stop function. Thus we actually don't need a set_dmamode
|
|
* method as the PIO method is always called and will set the right PIO
|
|
* timing parameters.
|
|
*/
|
|
|
|
#include <linux/kernel.h>
|
|
#include <linux/module.h>
|
|
#include <linux/pci.h>
|
|
#include <linux/init.h>
|
|
#include <linux/blkdev.h>
|
|
#include <linux/delay.h>
|
|
#include <scsi/scsi_host.h>
|
|
#include <linux/libata.h>
|
|
|
|
#define DRV_NAME "pata_sl82c105"
|
|
#define DRV_VERSION "0.3.3"
|
|
|
|
enum {
|
|
/*
|
|
* SL82C105 PCI config register 0x40 bits.
|
|
*/
|
|
CTRL_IDE_IRQB = (1 << 30),
|
|
CTRL_IDE_IRQA = (1 << 28),
|
|
CTRL_LEGIRQ = (1 << 11),
|
|
CTRL_P1F16 = (1 << 5),
|
|
CTRL_P1EN = (1 << 4),
|
|
CTRL_P0F16 = (1 << 1),
|
|
CTRL_P0EN = (1 << 0)
|
|
};
|
|
|
|
/**
|
|
* sl82c105_pre_reset - probe begin
|
|
* @link: ATA link
|
|
* @deadline: deadline jiffies for the operation
|
|
*
|
|
* Set up cable type and use generic probe init
|
|
*/
|
|
|
|
static int sl82c105_pre_reset(struct ata_link *link, unsigned long deadline)
|
|
{
|
|
static const struct pci_bits sl82c105_enable_bits[] = {
|
|
{ 0x40, 1, 0x01, 0x01 },
|
|
{ 0x40, 1, 0x10, 0x10 }
|
|
};
|
|
struct ata_port *ap = link->ap;
|
|
struct pci_dev *pdev = to_pci_dev(ap->host->dev);
|
|
|
|
if (ap->port_no && !pci_test_config_bits(pdev, &sl82c105_enable_bits[ap->port_no]))
|
|
return -ENOENT;
|
|
return ata_sff_prereset(link, deadline);
|
|
}
|
|
|
|
|
|
/**
|
|
* sl82c105_configure_piomode - set chip PIO timing
|
|
* @ap: ATA interface
|
|
* @adev: ATA device
|
|
* @pio: PIO mode
|
|
*
|
|
* Called to do the PIO mode setup. Our timing registers are shared
|
|
* so a configure_dmamode call will undo any work we do here and vice
|
|
* versa
|
|
*/
|
|
|
|
static void sl82c105_configure_piomode(struct ata_port *ap, struct ata_device *adev, int pio)
|
|
{
|
|
struct pci_dev *pdev = to_pci_dev(ap->host->dev);
|
|
static u16 pio_timing[5] = {
|
|
0x50D, 0x407, 0x304, 0x242, 0x240
|
|
};
|
|
u16 dummy;
|
|
int timing = 0x44 + (8 * ap->port_no) + (4 * adev->devno);
|
|
|
|
pci_write_config_word(pdev, timing, pio_timing[pio]);
|
|
/* Can we lose this oddity of the old driver */
|
|
pci_read_config_word(pdev, timing, &dummy);
|
|
}
|
|
|
|
/**
|
|
* sl82c105_set_piomode - set initial PIO mode data
|
|
* @ap: ATA interface
|
|
* @adev: ATA device
|
|
*
|
|
* Called to do the PIO mode setup. Our timing registers are shared
|
|
* but we want to set the PIO timing by default.
|
|
*/
|
|
|
|
static void sl82c105_set_piomode(struct ata_port *ap, struct ata_device *adev)
|
|
{
|
|
sl82c105_configure_piomode(ap, adev, adev->pio_mode - XFER_PIO_0);
|
|
}
|
|
|
|
/**
|
|
* sl82c105_configure_dmamode - set DMA mode in chip
|
|
* @ap: ATA interface
|
|
* @adev: ATA device
|
|
*
|
|
* Load DMA cycle times into the chip ready for a DMA transfer
|
|
* to occur.
|
|
*/
|
|
|
|
static void sl82c105_configure_dmamode(struct ata_port *ap, struct ata_device *adev)
|
|
{
|
|
struct pci_dev *pdev = to_pci_dev(ap->host->dev);
|
|
static u16 dma_timing[3] = {
|
|
0x707, 0x201, 0x200
|
|
};
|
|
u16 dummy;
|
|
int timing = 0x44 + (8 * ap->port_no) + (4 * adev->devno);
|
|
int dma = adev->dma_mode - XFER_MW_DMA_0;
|
|
|
|
pci_write_config_word(pdev, timing, dma_timing[dma]);
|
|
/* Can we lose this oddity of the old driver */
|
|
pci_read_config_word(pdev, timing, &dummy);
|
|
}
|
|
|
|
/**
|
|
* sl82c105_reset_engine - Reset the DMA engine
|
|
* @ap: ATA interface
|
|
*
|
|
* The sl82c105 has some serious problems with the DMA engine
|
|
* when transfers don't run as expected or ATAPI is used. The
|
|
* recommended fix is to reset the engine each use using a chip
|
|
* test register.
|
|
*/
|
|
|
|
static void sl82c105_reset_engine(struct ata_port *ap)
|
|
{
|
|
struct pci_dev *pdev = to_pci_dev(ap->host->dev);
|
|
u16 val;
|
|
|
|
pci_read_config_word(pdev, 0x7E, &val);
|
|
pci_write_config_word(pdev, 0x7E, val | 4);
|
|
pci_write_config_word(pdev, 0x7E, val & ~4);
|
|
}
|
|
|
|
/**
|
|
* sl82c105_bmdma_start - DMA engine begin
|
|
* @qc: ATA command
|
|
*
|
|
* Reset the DMA engine each use as recommended by the errata
|
|
* document.
|
|
*
|
|
* FIXME: if we switch clock at BMDMA start/end we might get better
|
|
* PIO performance on DMA capable devices.
|
|
*/
|
|
|
|
static void sl82c105_bmdma_start(struct ata_queued_cmd *qc)
|
|
{
|
|
struct ata_port *ap = qc->ap;
|
|
|
|
udelay(100);
|
|
sl82c105_reset_engine(ap);
|
|
udelay(100);
|
|
|
|
/* Set the clocks for DMA */
|
|
sl82c105_configure_dmamode(ap, qc->dev);
|
|
/* Activate DMA */
|
|
ata_bmdma_start(qc);
|
|
}
|
|
|
|
/**
|
|
* sl82c105_bmdma_end - DMA engine stop
|
|
* @qc: ATA command
|
|
*
|
|
* Reset the DMA engine each use as recommended by the errata
|
|
* document.
|
|
*
|
|
* This function is also called to turn off DMA when a timeout occurs
|
|
* during DMA operation. In both cases we need to reset the engine,
|
|
* so no actual eng_timeout handler is required.
|
|
*
|
|
* We assume bmdma_stop is always called if bmdma_start as called. If
|
|
* not then we may need to wrap qc_issue.
|
|
*/
|
|
|
|
static void sl82c105_bmdma_stop(struct ata_queued_cmd *qc)
|
|
{
|
|
struct ata_port *ap = qc->ap;
|
|
|
|
ata_bmdma_stop(qc);
|
|
sl82c105_reset_engine(ap);
|
|
udelay(100);
|
|
|
|
/* This will redo the initial setup of the DMA device to matching
|
|
PIO timings */
|
|
sl82c105_set_piomode(ap, qc->dev);
|
|
}
|
|
|
|
/**
|
|
* sl82c105_qc_defer - implement serialization
|
|
* @qc: command
|
|
*
|
|
* We must issue one command per host not per channel because
|
|
* of the reset bug.
|
|
*
|
|
* Q: is the scsi host lock sufficient ?
|
|
*/
|
|
|
|
static int sl82c105_qc_defer(struct ata_queued_cmd *qc)
|
|
{
|
|
struct ata_host *host = qc->ap->host;
|
|
struct ata_port *alt = host->ports[1 ^ qc->ap->port_no];
|
|
int rc;
|
|
|
|
/* First apply the usual rules */
|
|
rc = ata_std_qc_defer(qc);
|
|
if (rc != 0)
|
|
return rc;
|
|
|
|
/* Now apply serialization rules. Only allow a command if the
|
|
other channel state machine is idle */
|
|
if (alt && alt->qc_active)
|
|
return ATA_DEFER_PORT;
|
|
return 0;
|
|
}
|
|
|
|
static bool sl82c105_sff_irq_check(struct ata_port *ap)
|
|
{
|
|
struct pci_dev *pdev = to_pci_dev(ap->host->dev);
|
|
u32 val, mask = ap->port_no ? CTRL_IDE_IRQB : CTRL_IDE_IRQA;
|
|
|
|
pci_read_config_dword(pdev, 0x40, &val);
|
|
|
|
return val & mask;
|
|
}
|
|
|
|
static struct scsi_host_template sl82c105_sht = {
|
|
ATA_BMDMA_SHT(DRV_NAME),
|
|
};
|
|
|
|
static struct ata_port_operations sl82c105_port_ops = {
|
|
.inherits = &ata_bmdma_port_ops,
|
|
.qc_defer = sl82c105_qc_defer,
|
|
.bmdma_start = sl82c105_bmdma_start,
|
|
.bmdma_stop = sl82c105_bmdma_stop,
|
|
.cable_detect = ata_cable_40wire,
|
|
.set_piomode = sl82c105_set_piomode,
|
|
.prereset = sl82c105_pre_reset,
|
|
.sff_irq_check = sl82c105_sff_irq_check,
|
|
};
|
|
|
|
/**
|
|
* sl82c105_bridge_revision - find bridge version
|
|
* @pdev: PCI device for the ATA function
|
|
*
|
|
* Locates the PCI bridge associated with the ATA function and
|
|
* providing it is a Winbond 553 reports the revision. If it cannot
|
|
* find a revision or the right device it returns -1
|
|
*/
|
|
|
|
static int sl82c105_bridge_revision(struct pci_dev *pdev)
|
|
{
|
|
struct pci_dev *bridge;
|
|
|
|
/*
|
|
* The bridge should be part of the same device, but function 0.
|
|
*/
|
|
bridge = pci_get_slot(pdev->bus,
|
|
PCI_DEVFN(PCI_SLOT(pdev->devfn), 0));
|
|
if (!bridge)
|
|
return -1;
|
|
|
|
/*
|
|
* Make sure it is a Winbond 553 and is an ISA bridge.
|
|
*/
|
|
if (bridge->vendor != PCI_VENDOR_ID_WINBOND ||
|
|
bridge->device != PCI_DEVICE_ID_WINBOND_83C553 ||
|
|
bridge->class >> 8 != PCI_CLASS_BRIDGE_ISA) {
|
|
pci_dev_put(bridge);
|
|
return -1;
|
|
}
|
|
/*
|
|
* We need to find function 0's revision, not function 1
|
|
*/
|
|
pci_dev_put(bridge);
|
|
return bridge->revision;
|
|
}
|
|
|
|
static void sl82c105_fixup(struct pci_dev *pdev)
|
|
{
|
|
u32 val;
|
|
|
|
pci_read_config_dword(pdev, 0x40, &val);
|
|
val |= CTRL_P0EN | CTRL_P0F16 | CTRL_P1F16;
|
|
pci_write_config_dword(pdev, 0x40, val);
|
|
}
|
|
|
|
static int sl82c105_init_one(struct pci_dev *dev, const struct pci_device_id *id)
|
|
{
|
|
static const struct ata_port_info info_dma = {
|
|
.flags = ATA_FLAG_SLAVE_POSS,
|
|
.pio_mask = ATA_PIO4,
|
|
.mwdma_mask = ATA_MWDMA2,
|
|
.port_ops = &sl82c105_port_ops
|
|
};
|
|
static const struct ata_port_info info_early = {
|
|
.flags = ATA_FLAG_SLAVE_POSS,
|
|
.pio_mask = ATA_PIO4,
|
|
.port_ops = &sl82c105_port_ops
|
|
};
|
|
/* for now use only the first port */
|
|
const struct ata_port_info *ppi[] = { &info_early,
|
|
NULL };
|
|
int rev;
|
|
int rc;
|
|
|
|
rc = pcim_enable_device(dev);
|
|
if (rc)
|
|
return rc;
|
|
|
|
rev = sl82c105_bridge_revision(dev);
|
|
|
|
if (rev == -1)
|
|
dev_warn(&dev->dev,
|
|
"pata_sl82c105: Unable to find bridge, disabling DMA\n");
|
|
else if (rev <= 5)
|
|
dev_warn(&dev->dev,
|
|
"pata_sl82c105: Early bridge revision, no DMA available\n");
|
|
else
|
|
ppi[0] = &info_dma;
|
|
|
|
sl82c105_fixup(dev);
|
|
|
|
return ata_pci_bmdma_init_one(dev, ppi, &sl82c105_sht, NULL, 0);
|
|
}
|
|
|
|
#ifdef CONFIG_PM
|
|
static int sl82c105_reinit_one(struct pci_dev *pdev)
|
|
{
|
|
struct ata_host *host = dev_get_drvdata(&pdev->dev);
|
|
int rc;
|
|
|
|
rc = ata_pci_device_do_resume(pdev);
|
|
if (rc)
|
|
return rc;
|
|
|
|
sl82c105_fixup(pdev);
|
|
|
|
ata_host_resume(host);
|
|
return 0;
|
|
}
|
|
#endif
|
|
|
|
static const struct pci_device_id sl82c105[] = {
|
|
{ PCI_VDEVICE(WINBOND, PCI_DEVICE_ID_WINBOND_82C105), },
|
|
|
|
{ },
|
|
};
|
|
|
|
static struct pci_driver sl82c105_pci_driver = {
|
|
.name = DRV_NAME,
|
|
.id_table = sl82c105,
|
|
.probe = sl82c105_init_one,
|
|
.remove = ata_pci_remove_one,
|
|
#ifdef CONFIG_PM
|
|
.suspend = ata_pci_device_suspend,
|
|
.resume = sl82c105_reinit_one,
|
|
#endif
|
|
};
|
|
|
|
module_pci_driver(sl82c105_pci_driver);
|
|
|
|
MODULE_AUTHOR("Alan Cox");
|
|
MODULE_DESCRIPTION("low-level driver for Sl82c105");
|
|
MODULE_LICENSE("GPL");
|
|
MODULE_DEVICE_TABLE(pci, sl82c105);
|
|
MODULE_VERSION(DRV_VERSION);
|