133cea6680
As Mainlining effort for SolidRun CuBox has been carried out on the Engineering Sample, the board DTS was reflecting this. Actually, SolidRun CuBox comes in three different variants: Engineering Sample (ES), production with 1GB RAM (1G), and production with 2GB RAM (2G). Therefore, we base current dove-cubox.dts on to the 1G production variant and add a ES dts to add required quirk for misrouted SDHCI card detect on top of dove-cubox.dts. For the 2G variant we rely on the bootloader to setup correct RAM size. Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com> Link: https://lkml.kernel.org/r/1401228006-3212-1-git-send-email-sebastian.hesselbarth@gmail.com Signed-off-by: Jason Cooper <jason@lakedaemon.net>
134 lines
2.4 KiB
Plaintext
134 lines
2.4 KiB
Plaintext
/dts-v1/;
|
|
|
|
#include "dove.dtsi"
|
|
|
|
/ {
|
|
model = "SolidRun CuBox";
|
|
compatible = "solidrun,cubox", "marvell,dove";
|
|
|
|
memory {
|
|
device_type = "memory";
|
|
reg = <0x00000000 0x40000000>;
|
|
};
|
|
|
|
chosen {
|
|
bootargs = "console=ttyS0,115200n8 earlyprintk";
|
|
};
|
|
|
|
leds {
|
|
compatible = "gpio-leds";
|
|
pinctrl-0 = <&pmx_gpio_18>;
|
|
pinctrl-names = "default";
|
|
|
|
power {
|
|
label = "Power";
|
|
gpios = <&gpio0 18 1>;
|
|
default-state = "keep";
|
|
};
|
|
};
|
|
|
|
regulators {
|
|
compatible = "simple-bus";
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
|
|
usb_power: regulator@1 {
|
|
compatible = "regulator-fixed";
|
|
reg = <1>;
|
|
regulator-name = "USB Power";
|
|
regulator-min-microvolt = <5000000>;
|
|
regulator-max-microvolt = <5000000>;
|
|
enable-active-high;
|
|
regulator-always-on;
|
|
regulator-boot-on;
|
|
gpio = <&gpio0 1 0>;
|
|
pinctrl-0 = <&pmx_gpio_1>;
|
|
pinctrl-names = "default";
|
|
};
|
|
};
|
|
|
|
clocks {
|
|
/* 25MHz reference crystal */
|
|
ref25: oscillator {
|
|
compatible = "fixed-clock";
|
|
#clock-cells = <0>;
|
|
clock-frequency = <25000000>;
|
|
};
|
|
};
|
|
|
|
ir_recv: ir-receiver {
|
|
compatible = "gpio-ir-receiver";
|
|
gpios = <&gpio0 19 1>;
|
|
pinctrl-0 = <&pmx_gpio_19>;
|
|
pinctrl-names = "default";
|
|
};
|
|
};
|
|
|
|
&uart0 { status = "okay"; };
|
|
&sata0 { status = "okay"; };
|
|
&mdio { status = "okay"; };
|
|
ð { status = "okay"; };
|
|
|
|
ðphy {
|
|
compatible = "marvell,88e1310";
|
|
reg = <1>;
|
|
};
|
|
|
|
&i2c0 {
|
|
status = "okay";
|
|
clock-frequency = <100000>;
|
|
|
|
si5351: clock-generator {
|
|
compatible = "silabs,si5351a-msop";
|
|
reg = <0x60>;
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
#clock-cells = <1>;
|
|
|
|
/* connect xtal input to 25MHz reference */
|
|
clocks = <&ref25>;
|
|
|
|
/* connect xtal input as source of pll0 and pll1 */
|
|
silabs,pll-source = <0 0>, <1 0>;
|
|
|
|
clkout0 {
|
|
reg = <0>;
|
|
silabs,drive-strength = <8>;
|
|
silabs,multisynth-source = <0>;
|
|
silabs,clock-source = <0>;
|
|
silabs,pll-master;
|
|
};
|
|
|
|
clkout2 {
|
|
reg = <2>;
|
|
silabs,drive-strength = <8>;
|
|
silabs,multisynth-source = <1>;
|
|
silabs,clock-source = <0>;
|
|
silabs,pll-master;
|
|
};
|
|
};
|
|
};
|
|
|
|
&sdio0 {
|
|
status = "okay";
|
|
};
|
|
|
|
&spi0 {
|
|
status = "okay";
|
|
|
|
/* spi0.0: 4M Flash Winbond W25Q32BV */
|
|
spi-flash@0 {
|
|
compatible = "st,w25q32";
|
|
spi-max-frequency = <20000000>;
|
|
reg = <0>;
|
|
};
|
|
};
|
|
|
|
&audio1 {
|
|
status = "okay";
|
|
clocks = <&gate_clk 13>, <&si5351 2>;
|
|
clock-names = "internal", "extclk";
|
|
pinctrl-0 = <&pmx_audio1_i2s1_spdifo &pmx_audio1_extclk>;
|
|
pinctrl-names = "default";
|
|
};
|