linux/arch/arm/mach-omap2/usb-musb.c

224 lines
5.7 KiB
C

/*
* linux/arch/arm/mach-omap2/usb-musb.c
*
* This file will contain the board specific details for the
* MENTOR USB OTG controller on OMAP3430
*
* Copyright (C) 2007-2008 Texas Instruments
* Copyright (C) 2008 Nokia Corporation
* Author: Vikram Pandita
*
* Generalization by:
* Felipe Balbi <felipe.balbi@nokia.com>
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License version 2 as
* published by the Free Software Foundation.
*/
#include <linux/types.h>
#include <linux/errno.h>
#include <linux/delay.h>
#include <linux/platform_device.h>
#include <linux/clk.h>
#include <linux/dma-mapping.h>
#include <linux/io.h>
#include <linux/usb/musb.h>
#include <mach/hardware.h>
#include <mach/irqs.h>
#include <mach/am35xx.h>
#include <plat/usb.h>
#include "control.h"
#if defined(CONFIG_USB_MUSB_OMAP2PLUS) || defined (CONFIG_USB_MUSB_AM35X)
static void am35x_musb_reset(void)
{
u32 regval;
/* Reset the musb interface */
regval = omap_ctrl_readl(AM35XX_CONTROL_IP_SW_RESET);
regval |= AM35XX_USBOTGSS_SW_RST;
omap_ctrl_writel(regval, AM35XX_CONTROL_IP_SW_RESET);
regval &= ~AM35XX_USBOTGSS_SW_RST;
omap_ctrl_writel(regval, AM35XX_CONTROL_IP_SW_RESET);
regval = omap_ctrl_readl(AM35XX_CONTROL_IP_SW_RESET);
}
static void am35x_musb_phy_power(u8 on)
{
unsigned long timeout = jiffies + msecs_to_jiffies(100);
u32 devconf2;
if (on) {
/*
* Start the on-chip PHY and its PLL.
*/
devconf2 = omap_ctrl_readl(AM35XX_CONTROL_DEVCONF2);
devconf2 &= ~(CONF2_RESET | CONF2_PHYPWRDN | CONF2_OTGPWRDN);
devconf2 |= CONF2_PHY_PLLON;
omap_ctrl_writel(devconf2, AM35XX_CONTROL_DEVCONF2);
pr_info(KERN_INFO "Waiting for PHY clock good...\n");
while (!(omap_ctrl_readl(AM35XX_CONTROL_DEVCONF2)
& CONF2_PHYCLKGD)) {
cpu_relax();
if (time_after(jiffies, timeout)) {
pr_err(KERN_ERR "musb PHY clock good timed out\n");
break;
}
}
} else {
/*
* Power down the on-chip PHY.
*/
devconf2 = omap_ctrl_readl(AM35XX_CONTROL_DEVCONF2);
devconf2 &= ~CONF2_PHY_PLLON;
devconf2 |= CONF2_PHYPWRDN | CONF2_OTGPWRDN;
omap_ctrl_writel(devconf2, AM35XX_CONTROL_DEVCONF2);
}
}
static void am35x_musb_clear_irq(void)
{
u32 regval;
regval = omap_ctrl_readl(AM35XX_CONTROL_LVL_INTR_CLEAR);
regval |= AM35XX_USBOTGSS_INT_CLR;
omap_ctrl_writel(regval, AM35XX_CONTROL_LVL_INTR_CLEAR);
regval = omap_ctrl_readl(AM35XX_CONTROL_LVL_INTR_CLEAR);
}
static void am35x_musb_set_mode(u8 musb_mode)
{
u32 devconf2 = omap_ctrl_readl(AM35XX_CONTROL_DEVCONF2);
devconf2 &= ~CONF2_OTGMODE;
switch (musb_mode) {
#ifdef CONFIG_USB_MUSB_HDRC_HCD
case MUSB_HOST: /* Force VBUS valid, ID = 0 */
devconf2 |= CONF2_FORCE_HOST;
break;
#endif
#ifdef CONFIG_USB_GADGET_MUSB_HDRC
case MUSB_PERIPHERAL: /* Force VBUS valid, ID = 1 */
devconf2 |= CONF2_FORCE_DEVICE;
break;
#endif
#ifdef CONFIG_USB_MUSB_OTG
case MUSB_OTG: /* Don't override the VBUS/ID comparators */
devconf2 |= CONF2_NO_OVERRIDE;
break;
#endif
default:
pr_info(KERN_INFO "Unsupported mode %u\n", musb_mode);
}
omap_ctrl_writel(devconf2, AM35XX_CONTROL_DEVCONF2);
}
static struct resource musb_resources[] = {
[0] = { /* start and end set dynamically */
.flags = IORESOURCE_MEM,
},
[1] = { /* general IRQ */
.start = INT_243X_HS_USB_MC,
.flags = IORESOURCE_IRQ,
.name = "mc",
},
[2] = { /* DMA IRQ */
.start = INT_243X_HS_USB_DMA,
.flags = IORESOURCE_IRQ,
.name = "dma",
},
};
static struct musb_hdrc_config musb_config = {
.multipoint = 1,
.dyn_fifo = 1,
.num_eps = 16,
.ram_bits = 12,
};
static struct musb_hdrc_platform_data musb_plat = {
#ifdef CONFIG_USB_MUSB_OTG
.mode = MUSB_OTG,
#elif defined(CONFIG_USB_MUSB_HDRC_HCD)
.mode = MUSB_HOST,
#elif defined(CONFIG_USB_GADGET_MUSB_HDRC)
.mode = MUSB_PERIPHERAL,
#endif
/* .clock is set dynamically */
.config = &musb_config,
/* REVISIT charge pump on TWL4030 can supply up to
* 100 mA ... but this value is board-specific, like
* "mode", and should be passed to usb_musb_init().
*/
.power = 50, /* up to 100 mA */
};
static u64 musb_dmamask = DMA_BIT_MASK(32);
static struct platform_device musb_device = {
.name = "musb-omap2430",
.id = -1,
.dev = {
.dma_mask = &musb_dmamask,
.coherent_dma_mask = DMA_BIT_MASK(32),
.platform_data = &musb_plat,
},
.num_resources = ARRAY_SIZE(musb_resources),
.resource = musb_resources,
};
void __init usb_musb_init(struct omap_musb_board_data *board_data)
{
if (cpu_is_omap243x()) {
musb_resources[0].start = OMAP243X_HS_BASE;
} else if (cpu_is_omap3517() || cpu_is_omap3505()) {
musb_device.name = "musb-am35x";
musb_resources[0].start = AM35XX_IPSS_USBOTGSS_BASE;
musb_resources[1].start = INT_35XX_USBOTG_IRQ;
board_data->set_phy_power = am35x_musb_phy_power;
board_data->clear_irq = am35x_musb_clear_irq;
board_data->set_mode = am35x_musb_set_mode;
board_data->reset = am35x_musb_reset;
} else if (cpu_is_omap34xx()) {
musb_resources[0].start = OMAP34XX_HSUSB_OTG_BASE;
} else if (cpu_is_omap44xx()) {
musb_resources[0].start = OMAP44XX_HSUSB_OTG_BASE;
musb_resources[1].start = OMAP44XX_IRQ_HS_USB_MC_N;
musb_resources[2].start = OMAP44XX_IRQ_HS_USB_DMA_N;
}
musb_resources[0].end = musb_resources[0].start + SZ_4K - 1;
/*
* REVISIT: This line can be removed once all the platforms using
* musb_core.c have been converted to use use clkdev.
*/
musb_plat.clock = "ick";
musb_plat.board_data = board_data;
musb_plat.power = board_data->power >> 1;
musb_plat.mode = board_data->mode;
musb_plat.extvbus = board_data->extvbus;
if (platform_device_register(&musb_device) < 0)
printk(KERN_ERR "Unable to register HS-USB (MUSB) device\n");
}
#else
void __init usb_musb_init(struct omap_musb_board_data *board_data)
{
}
#endif /* CONFIG_USB_MUSB_SOC */