linux/drivers/char/mwave
Colin Ian King caa97be1a2 char/mwave: make some arrays static const to make object code smaller
Don't populate arrays on the stack but make them static.  Makes
the object code smaller.  Also remove temporary variables that
have hard coded array sizes and just use ARRAY_SIZE instead and
wrap some lines that are wider than 80 chars to clean up some
checkpatch warnings.

Before:
   text	   data	    bss	    dec	    hex	filename
  11141	   2008	     64	  13213	   339d	drivers/char/mwave/smapi.o

After:
   text	   data	    bss	    dec	    hex	filename
  10697	   2352	     64	  13113	   3339	drivers/char/mwave/smapi.o

Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-07-17 17:23:16 +02:00
..
3780i.c Replace <asm/uaccess.h> with <linux/uaccess.h> globally 2016-12-24 11:46:01 -08:00
3780i.h char/mwave: remove custom BOOLEAN type 2016-08-31 14:22:49 +02:00
Makefile char: change to new flag variable 2011-03-17 14:02:59 +01:00
README char: change to new flag variable 2011-03-17 14:02:59 +01:00
mwavedd.c Annotate hardware config module parameters in drivers/char/mwave/ 2017-04-20 12:02:32 +01:00
mwavedd.h Replace <asm/uaccess.h> with <linux/uaccess.h> globally 2016-12-24 11:46:01 -08:00
mwavepub.h
smapi.c char/mwave: make some arrays static const to make object code smaller 2017-07-17 17:23:16 +02:00
smapi.h char/mwave: remove custom BOOLEAN type 2016-08-31 14:22:49 +02:00
tp3780i.c char/mwave: remove custom BOOLEAN type 2016-08-31 14:22:49 +02:00
tp3780i.h

README

Module options
--------------

The mwave module takes the following options.  Note that these options
are not saved by the BIOS and so do not persist after unload and reload.

  mwave_debug=value, where value is bitwise OR of trace flags:
	0x0001 mwavedd api tracing
	0x0002 smapi api tracing
	0x0004 3780i tracing
	0x0008 tp3780i tracing

        Tracing only occurs if the driver has been compiled with the
        MW_TRACE macro #defined  (i.e. let ccflags-y := -DMW_TRACE
        in the Makefile).

  mwave_3780i_irq=5/7/10/11/15
	If the dsp irq has not been setup and stored in bios by the 
	thinkpad configuration utility then this parameter allows the
	irq used by the dsp to be configured.

  mwave_3780i_io=0x130/0x350/0x0070/0xDB0
	If the dsp io range has not been setup and stored in bios by the 
	thinkpad configuration utility then this parameter allows the
	io range used by the dsp to be configured.

  mwave_uart_irq=3/4
	If the mwave's uart irq has not been setup and stored in bios by the 
	thinkpad configuration utility then this parameter allows the
	irq used by the mwave uart to be configured.

  mwave_uart_io=0x3f8/0x2f8/0x3E8/0x2E8
	If the uart io range has not been setup and stored in bios by the 
	thinkpad configuration utility then this parameter allows the
	io range used by the mwave uart to be configured.

Example to enable the 3780i DSP using ttyS1 resources:
	
  insmod mwave mwave_3780i_irq=10 mwave_3780i_io=0x0130 mwave_uart_irq=3 mwave_uart_io=0x2f8

Accessing the driver
--------------------

You must also create a node for the driver:
  mkdir -p /dev/modems
  mknod --mode=660 /dev/modems/mwave c 10 219