OpenE2K/linux
6
0
Fork 0
Code Issues Pull Requests Releases Wiki Activity
2bf3010843
linux/drivers/ide/cmd64x.c
Mikulas Patocka 9bd7496f5d ide: Serialize CMD643 and CMD646 to fix a hardware bug with SSD 
CMD646 corrupts data on concurrent transfers on both channels when IDE SSD is
connected to one of the channels.

Setup that demonstrates this hardware bug: Ultra 5, onboard CMD646, rev 3.
/dev/hda is 8GB Seagate ST38410A in MWDMA2
/dev/hdd is 32GB SSD SiliconHardDisk in MWDMA2

- When reading /dev/hdd (for example with dd or fsck), reads from /dev/hda
  are corrupted, there are twiddled single bits 1->0 and some full 32-bit
  words corrupted, sometimes commands fail (which switches /dev/hda to
  PIO mode but the corruptions happen even in PIO).
- Reads from /dev/hdd don't seem to be corrupted (i.e. fsck passes fine).
- When I connected normal rotating harddisk to /dev/hdd, there was no
  corruption, so the corruption is something specific to SSD.
- I tried the same setup on a PCI card with CMD649 and saw no corruption.

This patch serializes the operation for CMD646 and 643 (I didn't test
CMD643 but it may have the same hw bug too because it's earlier design).
CMD649 is good. I don't know anything about CMD 648.

Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Tested-by: Frans Pop <elendil@planet.nl>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-10-29 03:02:06 -07:00

494 lines
13 KiB
C
Raw Blame History

/*
* cmd64x.c: Enable interrupts at initialization time on Ultra/PCI machines.
* Due to massive hardware bugs, UltraDMA is only supported
* on the 646U2 and not on the 646U.
*
* Copyright (C) 1998 Eddie C. Dost (ecd@skynet.be)
* Copyright (C) 1998 David S. Miller (davem@redhat.com)
*
* Copyright (C) 1999-2002 Andre Hedrick <andre@linux-ide.org>
* Copyright (C) 2007,2009 MontaVista Software, Inc. <source@mvista.com>
*/
#include <linux/module.h>
#include <linux/types.h>
#include <linux/pci.h>
#include <linux/ide.h>
#include <linux/init.h>
#include <asm/io.h>
#define DRV_NAME "cmd64x"
#define CMD_DEBUG 0
#if CMD_DEBUG
#define cmdprintk(x...) printk(x)
#else
#define cmdprintk(x...)
#endif
/*
* CMD64x specific registers definition.
*/
#define CFR 0x50
#define CFR_INTR_CH0 0x04
#define CMDTIM 0x52
#define ARTTIM0 0x53
#define DRWTIM0 0x54
#define ARTTIM1 0x55
#define DRWTIM1 0x56
#define ARTTIM23 0x57
#define ARTTIM23_DIS_RA2 0x04
#define ARTTIM23_DIS_RA3 0x08
#define ARTTIM23_INTR_CH1 0x10
#define DRWTIM2 0x58
#define BRST 0x59
#define DRWTIM3 0x5b
#define BMIDECR0 0x70
#define MRDMODE 0x71
#define MRDMODE_INTR_CH0 0x04
#define MRDMODE_INTR_CH1 0x08
#define UDIDETCR0 0x73
#define DTPR0 0x74
#define BMIDECR1 0x78
#define BMIDECSR 0x79
#define UDIDETCR1 0x7B
#define DTPR1 0x7C
static u8 quantize_timing(int timing, int quant)
{
return (timing + quant - 1) / quant;
}
/*
* This routine calculates active/recovery counts and then writes them into
* the chipset registers.
*/
static void program_cycle_times (ide_drive_t *drive, int cycle_time, int active_time)
{
struct pci_dev *dev = to_pci_dev(drive->hwif->dev);
int clock_time = 1000 / (ide_pci_clk ? ide_pci_clk : 33);
u8 cycle_count, active_count, recovery_count, drwtim;
static const u8 recovery_values[] =
{15, 15, 1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 11, 12, 13, 14, 0};
static const u8 drwtim_regs[4] = {DRWTIM0, DRWTIM1, DRWTIM2, DRWTIM3};
cmdprintk("program_cycle_times parameters: total=%d, active=%d\n",
cycle_time, active_time);
cycle_count = quantize_timing( cycle_time, clock_time);
active_count = quantize_timing(active_time, clock_time);
recovery_count = cycle_count - active_count;
/*
* In case we've got too long recovery phase, try to lengthen
* the active phase
*/
if (recovery_count > 16) {
active_count += recovery_count - 16;
recovery_count = 16;
}
if (active_count > 16) /* shouldn't actually happen... */
active_count = 16;
cmdprintk("Final counts: total=%d, active=%d, recovery=%d\n",
cycle_count, active_count, recovery_count);
/*
* Convert values to internal chipset representation
*/
recovery_count = recovery_values[recovery_count];
active_count &= 0x0f;
/* Program the active/recovery counts into the DRWTIM register */
drwtim = (active_count << 4) | recovery_count;
(void) pci_write_config_byte(dev, drwtim_regs[drive->dn], drwtim);
cmdprintk("Write 0x%02x to reg 0x%x\n", drwtim, drwtim_regs[drive->dn]);
}
/*
* This routine writes into the chipset registers
* PIO setup/active/recovery timings.
*/
static void cmd64x_tune_pio(ide_drive_t *drive, const u8 pio)
{
ide_hwif_t *hwif = drive->hwif;
struct pci_dev *dev = to_pci_dev(hwif->dev);
struct ide_timing *t = ide_timing_find_mode(XFER_PIO_0 + pio);
unsigned long setup_count;
unsigned int cycle_time;
u8 arttim = 0;
static const u8 setup_values[] = {0x40, 0x40, 0x40, 0x80, 0, 0xc0};
static const u8 arttim_regs[4] = {ARTTIM0, ARTTIM1, ARTTIM23, ARTTIM23};
cycle_time = ide_pio_cycle_time(drive, pio);
program_cycle_times(drive, cycle_time, t->active);
setup_count = quantize_timing(t->setup,
1000 / (ide_pci_clk ? ide_pci_clk : 33));
/*
* The primary channel has individual address setup timing registers
* for each drive and the hardware selects the slowest timing itself.
* The secondary channel has one common register and we have to select
* the slowest address setup timing ourselves.
*/
if (hwif->channel) {
ide_drive_t *pair = ide_get_pair_dev(drive);
ide_set_drivedata(drive, (void *)setup_count);
if (pair)
setup_count = max_t(u8, setup_count,
(unsigned long)ide_get_drivedata(pair));
}
if (setup_count > 5) /* shouldn't actually happen... */
setup_count = 5;
cmdprintk("Final address setup count: %d\n", setup_count);
/*
* Program the address setup clocks into the ARTTIM registers.
* Avoid clearing the secondary channel's interrupt bit.
*/
(void) pci_read_config_byte (dev, arttim_regs[drive->dn], &arttim);
if (hwif->channel)
arttim &= ~ARTTIM23_INTR_CH1;
arttim &= ~0xc0;
arttim |= setup_values[setup_count];
(void) pci_write_config_byte(dev, arttim_regs[drive->dn], arttim);
cmdprintk("Write 0x%02x to reg 0x%x\n", arttim, arttim_regs[drive->dn]);
}
/*
* Attempts to set drive's PIO mode.
* Special cases are 8: prefetch off, 9: prefetch on (both never worked)
*/
static void cmd64x_set_pio_mode(ide_drive_t *drive, const u8 pio)
{
/*
* Filter out the prefetch control values
* to prevent PIO5 from being programmed
*/
if (pio == 8 || pio == 9)
return;
cmd64x_tune_pio(drive, pio);
}
static void cmd64x_set_dma_mode(ide_drive_t *drive, const u8 speed)
{
ide_hwif_t *hwif = drive->hwif;
struct pci_dev *dev = to_pci_dev(hwif->dev);
u8 unit = drive->dn & 0x01;
u8 regU = 0, pciU = hwif->channel ? UDIDETCR1 : UDIDETCR0;
if (speed >= XFER_SW_DMA_0) {
(void) pci_read_config_byte(dev, pciU, &regU);
regU &= ~(unit ? 0xCA : 0x35);
}
switch(speed) {
case XFER_UDMA_5:
regU |= unit ? 0x0A : 0x05;
break;
case XFER_UDMA_4:
regU |= unit ? 0x4A : 0x15;
break;
case XFER_UDMA_3:
regU |= unit ? 0x8A : 0x25;
break;
case XFER_UDMA_2:
regU |= unit ? 0x42 : 0x11;
break;
case XFER_UDMA_1:
regU |= unit ? 0x82 : 0x21;
break;
case XFER_UDMA_0:
regU |= unit ? 0xC2 : 0x31;
break;
case XFER_MW_DMA_2:
program_cycle_times(drive, 120, 70);
break;
case XFER_MW_DMA_1:
program_cycle_times(drive, 150, 80);
break;
case XFER_MW_DMA_0:
program_cycle_times(drive, 480, 215);
break;
}
if (speed >= XFER_SW_DMA_0)
(void) pci_write_config_byte(dev, pciU, regU);
}
static void cmd648_clear_irq(ide_drive_t *drive)
{
ide_hwif_t *hwif = drive->hwif;
struct pci_dev *dev = to_pci_dev(hwif->dev);
unsigned long base = pci_resource_start(dev, 4);
u8 irq_mask = hwif->channel ? MRDMODE_INTR_CH1 :
MRDMODE_INTR_CH0;
u8 mrdmode = inb(base + 1);
/* clear the interrupt bit */
outb((mrdmode & ~(MRDMODE_INTR_CH0 | MRDMODE_INTR_CH1)) | irq_mask,
base + 1);
}
static void cmd64x_clear_irq(ide_drive_t *drive)
{
ide_hwif_t *hwif = drive->hwif;
struct pci_dev *dev = to_pci_dev(hwif->dev);
int irq_reg = hwif->channel ? ARTTIM23 : CFR;
u8 irq_mask = hwif->channel ? ARTTIM23_INTR_CH1 :
CFR_INTR_CH0;
u8 irq_stat = 0;
(void) pci_read_config_byte(dev, irq_reg, &irq_stat);
/* clear the interrupt bit */
(void) pci_write_config_byte(dev, irq_reg, irq_stat | irq_mask);
}
static int cmd648_test_irq(ide_hwif_t *hwif)
{
struct pci_dev *dev = to_pci_dev(hwif->dev);
unsigned long base = pci_resource_start(dev, 4);
u8 irq_mask = hwif->channel ? MRDMODE_INTR_CH1 :
MRDMODE_INTR_CH0;
u8 mrdmode = inb(base + 1);
pr_debug("%s: mrdmode: 0x%02x irq_mask: 0x%02x\n",
hwif->name, mrdmode, irq_mask);
return (mrdmode & irq_mask) ? 1 : 0;
}
static int cmd64x_test_irq(ide_hwif_t *hwif)
{
struct pci_dev *dev = to_pci_dev(hwif->dev);
int irq_reg = hwif->channel ? ARTTIM23 : CFR;
u8 irq_mask = hwif->channel ? ARTTIM23_INTR_CH1 :
CFR_INTR_CH0;
u8 irq_stat = 0;
(void) pci_read_config_byte(dev, irq_reg, &irq_stat);
pr_debug("%s: irq_stat: 0x%02x irq_mask: 0x%02x\n",
hwif->name, irq_stat, irq_mask);
return (irq_stat & irq_mask) ? 1 : 0;
}
/*
* ASUS P55T2P4D with CMD646 chipset revision 0x01 requires the old
* event order for DMA transfers.
*/
static int cmd646_1_dma_end(ide_drive_t *drive)
{
ide_hwif_t *hwif = drive->hwif;
u8 dma_stat = 0, dma_cmd = 0;
/* get DMA status */
dma_stat = inb(hwif->dma_base + ATA_DMA_STATUS);
/* read DMA command state */
dma_cmd = inb(hwif->dma_base + ATA_DMA_CMD);
/* stop DMA */
outb(dma_cmd & ~1, hwif->dma_base + ATA_DMA_CMD);
/* clear the INTR & ERROR bits */
outb(dma_stat | 6, hwif->dma_base + ATA_DMA_STATUS);
/* verify good DMA status */
return (dma_stat & 7) != 4;
}
static int init_chipset_cmd64x(struct pci_dev *dev)
{
u8 mrdmode = 0;
/* Set a good latency timer and cache line size value. */
(void) pci_write_config_byte(dev, PCI_LATENCY_TIMER, 64);
/* FIXME: pci_set_master() to ensure a good latency timer value */
/*
* Enable interrupts, select MEMORY READ LINE for reads.
*
* NOTE: although not mentioned in the PCI0646U specs,
* bits 0-1 are write only and won't be read back as
* set or not -- PCI0646U2 specs clarify this point.
*/
(void) pci_read_config_byte (dev, MRDMODE, &mrdmode);
mrdmode &= ~0x30;
(void) pci_write_config_byte(dev, MRDMODE, (mrdmode | 0x02));
return 0;
}
static u8 cmd64x_cable_detect(ide_hwif_t *hwif)
{
struct pci_dev *dev = to_pci_dev(hwif->dev);
u8 bmidecsr = 0, mask = hwif->channel ? 0x02 : 0x01;
switch (dev->device) {
case PCI_DEVICE_ID_CMD_648:
case PCI_DEVICE_ID_CMD_649:
pci_read_config_byte(dev, BMIDECSR, &bmidecsr);
return (bmidecsr & mask) ? ATA_CBL_PATA80 : ATA_CBL_PATA40;
default:
return ATA_CBL_PATA40;
}
}
static const struct ide_port_ops cmd64x_port_ops = {
.set_pio_mode = cmd64x_set_pio_mode,
.set_dma_mode = cmd64x_set_dma_mode,
.clear_irq = cmd64x_clear_irq,
.test_irq = cmd64x_test_irq,
.cable_detect = cmd64x_cable_detect,
};
static const struct ide_port_ops cmd648_port_ops = {
.set_pio_mode = cmd64x_set_pio_mode,
.set_dma_mode = cmd64x_set_dma_mode,
.clear_irq = cmd648_clear_irq,
.test_irq = cmd648_test_irq,
.cable_detect = cmd64x_cable_detect,
};
static const struct ide_dma_ops cmd646_rev1_dma_ops = {
.dma_host_set = ide_dma_host_set,
.dma_setup = ide_dma_setup,
.dma_start = ide_dma_start,
.dma_end = cmd646_1_dma_end,
.dma_test_irq = ide_dma_test_irq,
.dma_lost_irq = ide_dma_lost_irq,
.dma_timer_expiry = ide_dma_sff_timer_expiry,
.dma_sff_read_status = ide_dma_sff_read_status,
};
static const struct ide_port_info cmd64x_chipsets[] __devinitdata = {
{ /* 0: CMD643 */
.name = DRV_NAME,
.init_chipset = init_chipset_cmd64x,
.enablebits = {{0x00,0x00,0x00}, {0x51,0x08,0x08}},
.port_ops = &cmd64x_port_ops,
.host_flags = IDE_HFLAG_CLEAR_SIMPLEX |
IDE_HFLAG_ABUSE_PREFETCH |
IDE_HFLAG_SERIALIZE,
.pio_mask = ATA_PIO5,
.mwdma_mask = ATA_MWDMA2,
.udma_mask = 0x00, /* no udma */
},
{ /* 1: CMD646 */
.name = DRV_NAME,
.init_chipset = init_chipset_cmd64x,
.enablebits = {{0x51,0x04,0x04}, {0x51,0x08,0x08}},
.port_ops = &cmd648_port_ops,
.host_flags = IDE_HFLAG_ABUSE_PREFETCH |
IDE_HFLAG_SERIALIZE,
.pio_mask = ATA_PIO5,
.mwdma_mask = ATA_MWDMA2,
.udma_mask = ATA_UDMA2,
},
{ /* 2: CMD648 */
.name = DRV_NAME,
.init_chipset = init_chipset_cmd64x,
.enablebits = {{0x51,0x04,0x04}, {0x51,0x08,0x08}},
.port_ops = &cmd648_port_ops,
.host_flags = IDE_HFLAG_ABUSE_PREFETCH,
.pio_mask = ATA_PIO5,
.mwdma_mask = ATA_MWDMA2,
.udma_mask = ATA_UDMA4,
},
{ /* 3: CMD649 */
.name = DRV_NAME,
.init_chipset = init_chipset_cmd64x,
.enablebits = {{0x51,0x04,0x04}, {0x51,0x08,0x08}},
.port_ops = &cmd648_port_ops,
.host_flags = IDE_HFLAG_ABUSE_PREFETCH,
.pio_mask = ATA_PIO5,
.mwdma_mask = ATA_MWDMA2,
.udma_mask = ATA_UDMA5,
}
};
static int __devinit cmd64x_init_one(struct pci_dev *dev, const struct pci_device_id *id)
{
struct ide_port_info d;
u8 idx = id->driver_data;
d = cmd64x_chipsets[idx];
if (idx == 1) {
/*
* UltraDMA only supported on PCI646U and PCI646U2, which
* correspond to revisions 0x03, 0x05 and 0x07 respectively.
* Actually, although the CMD tech support people won't
* tell me the details, the 0x03 revision cannot support
* UDMA correctly without hardware modifications, and even
* then it only works with Quantum disks due to some
* hold time assumptions in the 646U part which are fixed
* in the 646U2.
*
* So we only do UltraDMA on revision 0x05 and 0x07 chipsets.
*/
if (dev->revision < 5) {
d.udma_mask = 0x00;
/*
* The original PCI0646 didn't have the primary
* channel enable bit, it appeared starting with
* PCI0646U (i.e. revision ID 3).
*/
if (dev->revision < 3) {
d.enablebits[0].reg = 0;
d.port_ops = &cmd64x_port_ops;
if (dev->revision == 1)
d.dma_ops = &cmd646_rev1_dma_ops;
}
}
}
return ide_pci_init_one(dev, &d, NULL);
}
static const struct pci_device_id cmd64x_pci_tbl[] = {
{ PCI_VDEVICE(CMD, PCI_DEVICE_ID_CMD_643), 0 },
{ PCI_VDEVICE(CMD, PCI_DEVICE_ID_CMD_646), 1 },
{ PCI_VDEVICE(CMD, PCI_DEVICE_ID_CMD_648), 2 },
{ PCI_VDEVICE(CMD, PCI_DEVICE_ID_CMD_649), 3 },
{ 0, },
};
MODULE_DEVICE_TABLE(pci, cmd64x_pci_tbl);
static struct pci_driver cmd64x_pci_driver = {
.name = "CMD64x_IDE",
.id_table = cmd64x_pci_tbl,
.probe = cmd64x_init_one,
.remove = ide_pci_remove,
.suspend = ide_pci_suspend,
.resume = ide_pci_resume,
};
static int __init cmd64x_ide_init(void)
{
return ide_pci_register_driver(&cmd64x_pci_driver);
}
static void __exit cmd64x_ide_exit(void)
{
pci_unregister_driver(&cmd64x_pci_driver);
}
module_init(cmd64x_ide_init);
module_exit(cmd64x_ide_exit);
MODULE_AUTHOR("Eddie Dost, David Miller, Andre Hedrick");
MODULE_DESCRIPTION("PCI driver module for CMD64x IDE");
MODULE_LICENSE("GPL");
Reference in New Issue View Git Blame Copy Permalink