3a544354d5
With the addition of the gpmc_cs_program_settings(), we no longer need or use gpmc_cs_configure() to configure some of the GPMC chip-select options. So rename the function to gpmc_configure() and remove code that modifies options in the CONFIG1 register. Signed-off-by: Jon Hunter <jon-hunter@ti.com> Tested-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
230 lines
8.0 KiB
C
230 lines
8.0 KiB
C
/*
|
|
* General-Purpose Memory Controller for OMAP2
|
|
*
|
|
* Copyright (C) 2005-2006 Nokia Corporation
|
|
*
|
|
* This program is free software; you can redistribute it and/or modify
|
|
* it under the terms of the GNU General Public License version 2 as
|
|
* published by the Free Software Foundation.
|
|
*/
|
|
|
|
#ifndef __OMAP2_GPMC_H
|
|
#define __OMAP2_GPMC_H
|
|
|
|
#include <linux/platform_data/mtd-nand-omap2.h>
|
|
|
|
/* Maximum Number of Chip Selects */
|
|
#define GPMC_CS_NUM 8
|
|
|
|
#define GPMC_CS_CONFIG1 0x00
|
|
#define GPMC_CS_CONFIG2 0x04
|
|
#define GPMC_CS_CONFIG3 0x08
|
|
#define GPMC_CS_CONFIG4 0x0c
|
|
#define GPMC_CS_CONFIG5 0x10
|
|
#define GPMC_CS_CONFIG6 0x14
|
|
#define GPMC_CS_CONFIG7 0x18
|
|
#define GPMC_CS_NAND_COMMAND 0x1c
|
|
#define GPMC_CS_NAND_ADDRESS 0x20
|
|
#define GPMC_CS_NAND_DATA 0x24
|
|
|
|
/* Control Commands */
|
|
#define GPMC_CONFIG_RDY_BSY 0x00000001
|
|
#define GPMC_CONFIG_DEV_SIZE 0x00000002
|
|
#define GPMC_CONFIG_DEV_TYPE 0x00000003
|
|
#define GPMC_SET_IRQ_STATUS 0x00000004
|
|
#define GPMC_CONFIG_WP 0x00000005
|
|
|
|
#define GPMC_ENABLE_IRQ 0x0000000d
|
|
|
|
/* ECC commands */
|
|
#define GPMC_ECC_READ 0 /* Reset Hardware ECC for read */
|
|
#define GPMC_ECC_WRITE 1 /* Reset Hardware ECC for write */
|
|
#define GPMC_ECC_READSYN 2 /* Reset before syndrom is read back */
|
|
|
|
#define GPMC_CONFIG1_WRAPBURST_SUPP (1 << 31)
|
|
#define GPMC_CONFIG1_READMULTIPLE_SUPP (1 << 30)
|
|
#define GPMC_CONFIG1_READTYPE_ASYNC (0 << 29)
|
|
#define GPMC_CONFIG1_READTYPE_SYNC (1 << 29)
|
|
#define GPMC_CONFIG1_WRITEMULTIPLE_SUPP (1 << 28)
|
|
#define GPMC_CONFIG1_WRITETYPE_ASYNC (0 << 27)
|
|
#define GPMC_CONFIG1_WRITETYPE_SYNC (1 << 27)
|
|
#define GPMC_CONFIG1_CLKACTIVATIONTIME(val) ((val & 3) << 25)
|
|
#define GPMC_CONFIG1_PAGE_LEN(val) ((val & 3) << 23)
|
|
#define GPMC_CONFIG1_WAIT_READ_MON (1 << 22)
|
|
#define GPMC_CONFIG1_WAIT_WRITE_MON (1 << 21)
|
|
#define GPMC_CONFIG1_WAIT_MON_IIME(val) ((val & 3) << 18)
|
|
#define GPMC_CONFIG1_WAIT_PIN_SEL(val) ((val & 3) << 16)
|
|
#define GPMC_CONFIG1_DEVICESIZE(val) ((val & 3) << 12)
|
|
#define GPMC_CONFIG1_DEVICESIZE_16 GPMC_CONFIG1_DEVICESIZE(1)
|
|
#define GPMC_CONFIG1_DEVICETYPE(val) ((val & 3) << 10)
|
|
#define GPMC_CONFIG1_DEVICETYPE_NOR GPMC_CONFIG1_DEVICETYPE(0)
|
|
#define GPMC_CONFIG1_MUXTYPE(val) ((val & 3) << 8)
|
|
#define GPMC_CONFIG1_TIME_PARA_GRAN (1 << 4)
|
|
#define GPMC_CONFIG1_FCLK_DIV(val) (val & 3)
|
|
#define GPMC_CONFIG1_FCLK_DIV2 (GPMC_CONFIG1_FCLK_DIV(1))
|
|
#define GPMC_CONFIG1_FCLK_DIV3 (GPMC_CONFIG1_FCLK_DIV(2))
|
|
#define GPMC_CONFIG1_FCLK_DIV4 (GPMC_CONFIG1_FCLK_DIV(3))
|
|
#define GPMC_CONFIG7_CSVALID (1 << 6)
|
|
|
|
#define GPMC_DEVICETYPE_NOR 0
|
|
#define GPMC_DEVICETYPE_NAND 2
|
|
#define GPMC_CONFIG_WRITEPROTECT 0x00000010
|
|
#define WR_RD_PIN_MONITORING 0x00600000
|
|
#define GPMC_IRQ_FIFOEVENTENABLE 0x01
|
|
#define GPMC_IRQ_COUNT_EVENT 0x02
|
|
|
|
#define GPMC_BURST_4 4 /* 4 word burst */
|
|
#define GPMC_BURST_8 8 /* 8 word burst */
|
|
#define GPMC_BURST_16 16 /* 16 word burst */
|
|
#define GPMC_DEVWIDTH_8BIT 1 /* 8-bit device width */
|
|
#define GPMC_DEVWIDTH_16BIT 2 /* 16-bit device width */
|
|
#define GPMC_MUX_AAD 1 /* Addr-Addr-Data multiplex */
|
|
#define GPMC_MUX_AD 2 /* Addr-Data multiplex */
|
|
|
|
/* bool type time settings */
|
|
struct gpmc_bool_timings {
|
|
bool cycle2cyclediffcsen;
|
|
bool cycle2cyclesamecsen;
|
|
bool we_extra_delay;
|
|
bool oe_extra_delay;
|
|
bool adv_extra_delay;
|
|
bool cs_extra_delay;
|
|
bool time_para_granularity;
|
|
};
|
|
|
|
/*
|
|
* Note that all values in this struct are in nanoseconds except sync_clk
|
|
* (which is in picoseconds), while the register values are in gpmc_fck cycles.
|
|
*/
|
|
struct gpmc_timings {
|
|
/* Minimum clock period for synchronous mode (in picoseconds) */
|
|
u32 sync_clk;
|
|
|
|
/* Chip-select signal timings corresponding to GPMC_CS_CONFIG2 */
|
|
u32 cs_on; /* Assertion time */
|
|
u32 cs_rd_off; /* Read deassertion time */
|
|
u32 cs_wr_off; /* Write deassertion time */
|
|
|
|
/* ADV signal timings corresponding to GPMC_CONFIG3 */
|
|
u32 adv_on; /* Assertion time */
|
|
u32 adv_rd_off; /* Read deassertion time */
|
|
u32 adv_wr_off; /* Write deassertion time */
|
|
|
|
/* WE signals timings corresponding to GPMC_CONFIG4 */
|
|
u32 we_on; /* WE assertion time */
|
|
u32 we_off; /* WE deassertion time */
|
|
|
|
/* OE signals timings corresponding to GPMC_CONFIG4 */
|
|
u32 oe_on; /* OE assertion time */
|
|
u32 oe_off; /* OE deassertion time */
|
|
|
|
/* Access time and cycle time timings corresponding to GPMC_CONFIG5 */
|
|
u32 page_burst_access; /* Multiple access word delay */
|
|
u32 access; /* Start-cycle to first data valid delay */
|
|
u32 rd_cycle; /* Total read cycle time */
|
|
u32 wr_cycle; /* Total write cycle time */
|
|
|
|
u32 bus_turnaround;
|
|
u32 cycle2cycle_delay;
|
|
|
|
u32 wait_monitoring;
|
|
u32 clk_activation;
|
|
|
|
/* The following are only on OMAP3430 */
|
|
u32 wr_access; /* WRACCESSTIME */
|
|
u32 wr_data_mux_bus; /* WRDATAONADMUXBUS */
|
|
|
|
struct gpmc_bool_timings bool_timings;
|
|
};
|
|
|
|
/* Device timings in picoseconds */
|
|
struct gpmc_device_timings {
|
|
u32 t_ceasu; /* address setup to CS valid */
|
|
u32 t_avdasu; /* address setup to ADV valid */
|
|
/* XXX: try to combine t_avdp_r & t_avdp_w. Issue is
|
|
* of tusb using these timings even for sync whilst
|
|
* ideally for adv_rd/(wr)_off it should have considered
|
|
* t_avdh instead. This indirectly necessitates r/w
|
|
* variations of t_avdp as it is possible to have one
|
|
* sync & other async
|
|
*/
|
|
u32 t_avdp_r; /* ADV low time (what about t_cer ?) */
|
|
u32 t_avdp_w;
|
|
u32 t_aavdh; /* address hold time */
|
|
u32 t_oeasu; /* address setup to OE valid */
|
|
u32 t_aa; /* access time from ADV assertion */
|
|
u32 t_iaa; /* initial access time */
|
|
u32 t_oe; /* access time from OE assertion */
|
|
u32 t_ce; /* access time from CS asertion */
|
|
u32 t_rd_cycle; /* read cycle time */
|
|
u32 t_cez_r; /* read CS deassertion to high Z */
|
|
u32 t_cez_w; /* write CS deassertion to high Z */
|
|
u32 t_oez; /* OE deassertion to high Z */
|
|
u32 t_weasu; /* address setup to WE valid */
|
|
u32 t_wpl; /* write assertion time */
|
|
u32 t_wph; /* write deassertion time */
|
|
u32 t_wr_cycle; /* write cycle time */
|
|
|
|
u32 clk;
|
|
u32 t_bacc; /* burst access valid clock to output delay */
|
|
u32 t_ces; /* CS setup time to clk */
|
|
u32 t_avds; /* ADV setup time to clk */
|
|
u32 t_avdh; /* ADV hold time from clk */
|
|
u32 t_ach; /* address hold time from clk */
|
|
u32 t_rdyo; /* clk to ready valid */
|
|
|
|
u32 t_ce_rdyz; /* XXX: description ?, or use t_cez instead */
|
|
u32 t_ce_avd; /* CS on to ADV on delay */
|
|
|
|
/* XXX: check the possibility of combining
|
|
* cyc_aavhd_oe & cyc_aavdh_we
|
|
*/
|
|
u8 cyc_aavdh_oe;/* read address hold time in cycles */
|
|
u8 cyc_aavdh_we;/* write address hold time in cycles */
|
|
u8 cyc_oe; /* access time from OE assertion in cycles */
|
|
u8 cyc_wpl; /* write deassertion time in cycles */
|
|
u32 cyc_iaa; /* initial access time in cycles */
|
|
|
|
/* extra delays */
|
|
bool ce_xdelay;
|
|
bool avd_xdelay;
|
|
bool oe_xdelay;
|
|
bool we_xdelay;
|
|
};
|
|
|
|
struct gpmc_settings {
|
|
bool burst_wrap; /* enables wrap bursting */
|
|
bool burst_read; /* enables read page/burst mode */
|
|
bool burst_write; /* enables write page/burst mode */
|
|
bool device_nand; /* device is NAND */
|
|
bool sync_read; /* enables synchronous reads */
|
|
bool sync_write; /* enables synchronous writes */
|
|
bool wait_on_read; /* monitor wait on reads */
|
|
bool wait_on_write; /* monitor wait on writes */
|
|
u32 burst_len; /* page/burst length */
|
|
u32 device_width; /* device bus width (8 or 16 bit) */
|
|
u32 mux_add_data; /* multiplex address & data */
|
|
u32 wait_pin; /* wait-pin to be used */
|
|
};
|
|
|
|
extern int gpmc_calc_timings(struct gpmc_timings *gpmc_t,
|
|
struct gpmc_settings *gpmc_s,
|
|
struct gpmc_device_timings *dev_t);
|
|
|
|
extern void gpmc_update_nand_reg(struct gpmc_nand_regs *reg, int cs);
|
|
extern int gpmc_get_client_irq(unsigned irq_config);
|
|
|
|
extern unsigned int gpmc_ticks_to_ns(unsigned int ticks);
|
|
|
|
extern void gpmc_cs_write_reg(int cs, int idx, u32 val);
|
|
extern int gpmc_calc_divider(unsigned int sync_clk);
|
|
extern int gpmc_cs_set_timings(int cs, const struct gpmc_timings *t);
|
|
extern int gpmc_cs_program_settings(int cs, struct gpmc_settings *p);
|
|
extern int gpmc_cs_request(int cs, unsigned long size, unsigned long *base);
|
|
extern void gpmc_cs_free(int cs);
|
|
extern void omap3_gpmc_save_context(void);
|
|
extern void omap3_gpmc_restore_context(void);
|
|
extern int gpmc_configure(int cmd, int wval);
|
|
|
|
#endif
|