OpenE2K/linux
6
0
Fork 0
Code Issues Pull Requests Releases Wiki Activity
459e97ee34
linux/drivers/gpu/drm/gma500/psb_intel_reg.h
Patrik Jakobsson 9e8e463609 drm/gma500: Clean up various defines 
Remove unused defines that we'll never use and fix naming in some include guards

Signed-off-by: Patrik Jakobsson <patrik.r.jakobsson@gmail.com>
2013-03-17 18:32:56 +01:00

1546 lines
50 KiB
C
Raw Blame History

/*
* Copyright (c) 2009, Intel Corporation.
*
* This program is free software; you can redistribute it and/or modify it
* under the terms and conditions of the GNU General Public License,
* version 2, as published by the Free Software Foundation.
*
* This program is distributed in the hope it will be useful, but WITHOUT
* ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
* FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for
* more details.
*
* You should have received a copy of the GNU General Public License along with
* this program; if not, write to the Free Software Foundation, Inc.,
* 51 Franklin St - Fifth Floor, Boston, MA 02110-1301 USA.
*/
#ifndef __PSB_INTEL_REG_H__
#define __PSB_INTEL_REG_H__
/*
* GPIO regs
*/
#define GPIOA 0x5010
#define GPIOB 0x5014
#define GPIOC 0x5018
#define GPIOD 0x501c
#define GPIOE 0x5020
#define GPIOF 0x5024
#define GPIOG 0x5028
#define GPIOH 0x502c
# define GPIO_CLOCK_DIR_MASK (1 << 0)
# define GPIO_CLOCK_DIR_IN (0 << 1)
# define GPIO_CLOCK_DIR_OUT (1 << 1)
# define GPIO_CLOCK_VAL_MASK (1 << 2)
# define GPIO_CLOCK_VAL_OUT (1 << 3)
# define GPIO_CLOCK_VAL_IN (1 << 4)
# define GPIO_CLOCK_PULLUP_DISABLE (1 << 5)
# define GPIO_DATA_DIR_MASK (1 << 8)
# define GPIO_DATA_DIR_IN (0 << 9)
# define GPIO_DATA_DIR_OUT (1 << 9)
# define GPIO_DATA_VAL_MASK (1 << 10)
# define GPIO_DATA_VAL_OUT (1 << 11)
# define GPIO_DATA_VAL_IN (1 << 12)
# define GPIO_DATA_PULLUP_DISABLE (1 << 13)
#define GMBUS0 0x5100 /* clock/port select */
#define GMBUS_RATE_100KHZ (0<<8)
#define GMBUS_RATE_50KHZ (1<<8)
#define GMBUS_RATE_400KHZ (2<<8) /* reserved on Pineview */
#define GMBUS_RATE_1MHZ (3<<8) /* reserved on Pineview */
#define GMBUS_HOLD_EXT (1<<7) /* 300ns hold time, rsvd on Pineview */
#define GMBUS_PORT_DISABLED 0
#define GMBUS_PORT_SSC 1
#define GMBUS_PORT_VGADDC 2
#define GMBUS_PORT_PANEL 3
#define GMBUS_PORT_DPC 4 /* HDMIC */
#define GMBUS_PORT_DPB 5 /* SDVO, HDMIB */
/* 6 reserved */
#define GMBUS_PORT_DPD 7 /* HDMID */
#define GMBUS_NUM_PORTS 8
#define GMBUS1 0x5104 /* command/status */
#define GMBUS_SW_CLR_INT (1<<31)
#define GMBUS_SW_RDY (1<<30)
#define GMBUS_ENT (1<<29) /* enable timeout */
#define GMBUS_CYCLE_NONE (0<<25)
#define GMBUS_CYCLE_WAIT (1<<25)
#define GMBUS_CYCLE_INDEX (2<<25)
#define GMBUS_CYCLE_STOP (4<<25)
#define GMBUS_BYTE_COUNT_SHIFT 16
#define GMBUS_SLAVE_INDEX_SHIFT 8
#define GMBUS_SLAVE_ADDR_SHIFT 1
#define GMBUS_SLAVE_READ (1<<0)
#define GMBUS_SLAVE_WRITE (0<<0)
#define GMBUS2 0x5108 /* status */
#define GMBUS_INUSE (1<<15)
#define GMBUS_HW_WAIT_PHASE (1<<14)
#define GMBUS_STALL_TIMEOUT (1<<13)
#define GMBUS_INT (1<<12)
#define GMBUS_HW_RDY (1<<11)
#define GMBUS_SATOER (1<<10)
#define GMBUS_ACTIVE (1<<9)
#define GMBUS3 0x510c /* data buffer bytes 3-0 */
#define GMBUS4 0x5110 /* interrupt mask (Pineview+) */
#define GMBUS_SLAVE_TIMEOUT_EN (1<<4)
#define GMBUS_NAK_EN (1<<3)
#define GMBUS_IDLE_EN (1<<2)
#define GMBUS_HW_WAIT_EN (1<<1)
#define GMBUS_HW_RDY_EN (1<<0)
#define GMBUS5 0x5120 /* byte index */
#define GMBUS_2BYTE_INDEX_EN (1<<31)
#define BLC_PWM_CTL 0x61254
#define BLC_PWM_CTL2 0x61250
#define PWM_ENABLE (1 << 31)
#define PWM_LEGACY_MODE (1 << 30)
#define PWM_PIPE_B (1 << 29)
#define BLC_PWM_CTL_C 0x62254
#define BLC_PWM_CTL2_C 0x62250
#define BACKLIGHT_MODULATION_FREQ_SHIFT (17)
/*
* This is the most significant 15 bits of the number of backlight cycles in a
* complete cycle of the modulated backlight control.
*
* The actual value is this field multiplied by two.
*/
#define BACKLIGHT_MODULATION_FREQ_MASK (0x7fff << 17)
#define BLM_LEGACY_MODE (1 << 16)
/*
* This is the number of cycles out of the backlight modulation cycle for which
* the backlight is on.
*
* This field must be no greater than the number of cycles in the complete
* backlight modulation cycle.
*/
#define BACKLIGHT_DUTY_CYCLE_SHIFT (0)
#define BACKLIGHT_DUTY_CYCLE_MASK (0xffff)
#define I915_GCFGC 0xf0
#define I915_LOW_FREQUENCY_ENABLE (1 << 7)
#define I915_DISPLAY_CLOCK_190_200_MHZ (0 << 4)
#define I915_DISPLAY_CLOCK_333_MHZ (4 << 4)
#define I915_DISPLAY_CLOCK_MASK (7 << 4)
#define I855_HPLLCC 0xc0
#define I855_CLOCK_CONTROL_MASK (3 << 0)
#define I855_CLOCK_133_200 (0 << 0)
#define I855_CLOCK_100_200 (1 << 0)
#define I855_CLOCK_100_133 (2 << 0)
#define I855_CLOCK_166_250 (3 << 0)
/* I830 CRTC registers */
#define HTOTAL_A 0x60000
#define HBLANK_A 0x60004
#define HSYNC_A 0x60008
#define VTOTAL_A 0x6000c
#define VBLANK_A 0x60010
#define VSYNC_A 0x60014
#define PIPEASRC 0x6001c
#define BCLRPAT_A 0x60020
#define VSYNCSHIFT_A 0x60028
#define HTOTAL_B 0x61000
#define HBLANK_B 0x61004
#define HSYNC_B 0x61008
#define VTOTAL_B 0x6100c
#define VBLANK_B 0x61010
#define VSYNC_B 0x61014
#define PIPEBSRC 0x6101c
#define BCLRPAT_B 0x61020
#define VSYNCSHIFT_B 0x61028
#define HTOTAL_C 0x62000
#define HBLANK_C 0x62004
#define HSYNC_C 0x62008
#define VTOTAL_C 0x6200c
#define VBLANK_C 0x62010
#define VSYNC_C 0x62014
#define PIPECSRC 0x6201c
#define BCLRPAT_C 0x62020
#define VSYNCSHIFT_C 0x62028
#define PP_STATUS 0x61200
# define PP_ON (1 << 31)
/*
* Indicates that all dependencies of the panel are on:
*
* - PLL enabled
* - pipe enabled
* - LVDS/DVOB/DVOC on
*/
#define PP_READY (1 << 30)
#define PP_SEQUENCE_NONE (0 << 28)
#define PP_SEQUENCE_ON (1 << 28)
#define PP_SEQUENCE_OFF (2 << 28)
#define PP_SEQUENCE_MASK 0x30000000
#define PP_CYCLE_DELAY_ACTIVE (1 << 27)
#define PP_SEQUENCE_STATE_ON_IDLE (1 << 3)
#define PP_SEQUENCE_STATE_MASK 0x0000000f
#define PP_CONTROL 0x61204
#define POWER_TARGET_ON (1 << 0)
#define PANEL_UNLOCK_REGS (0xabcd << 16)
#define PANEL_UNLOCK_MASK (0xffff << 16)
#define EDP_FORCE_VDD (1 << 3)
#define EDP_BLC_ENABLE (1 << 2)
#define PANEL_POWER_RESET (1 << 1)
#define PANEL_POWER_OFF (0 << 0)
#define PANEL_POWER_ON (1 << 0)
/* Poulsbo/Oaktrail */
#define LVDSPP_ON 0x61208
#define LVDSPP_OFF 0x6120c
#define PP_CYCLE 0x61210
/* Cedartrail */
#define PP_ON_DELAYS 0x61208 /* Cedartrail */
#define PANEL_PORT_SELECT_MASK (3 << 30)
#define PANEL_PORT_SELECT_LVDS (0 << 30)
#define PANEL_PORT_SELECT_EDP (1 << 30)
#define PANEL_POWER_UP_DELAY_MASK (0x1fff0000)
#define PANEL_POWER_UP_DELAY_SHIFT 16
#define PANEL_LIGHT_ON_DELAY_MASK (0x1fff)
#define PANEL_LIGHT_ON_DELAY_SHIFT 0
#define PP_OFF_DELAYS 0x6120c /* Cedartrail */
#define PANEL_POWER_DOWN_DELAY_MASK (0x1fff0000)
#define PANEL_POWER_DOWN_DELAY_SHIFT 16
#define PANEL_LIGHT_OFF_DELAY_MASK (0x1fff)
#define PANEL_LIGHT_OFF_DELAY_SHIFT 0
#define PP_DIVISOR 0x61210 /* Cedartrail */
#define PP_REFERENCE_DIVIDER_MASK (0xffffff00)
#define PP_REFERENCE_DIVIDER_SHIFT 8
#define PANEL_POWER_CYCLE_DELAY_MASK (0x1f)
#define PANEL_POWER_CYCLE_DELAY_SHIFT 0
#define PFIT_CONTROL 0x61230
#define PFIT_ENABLE (1 << 31)
#define PFIT_PIPE_MASK (3 << 29)
#define PFIT_PIPE_SHIFT 29
#define PFIT_SCALING_MODE_PILLARBOX (1 << 27)
#define PFIT_SCALING_MODE_LETTERBOX (3 << 26)
#define VERT_INTERP_DISABLE (0 << 10)
#define VERT_INTERP_BILINEAR (1 << 10)
#define VERT_INTERP_MASK (3 << 10)
#define VERT_AUTO_SCALE (1 << 9)
#define HORIZ_INTERP_DISABLE (0 << 6)
#define HORIZ_INTERP_BILINEAR (1 << 6)
#define HORIZ_INTERP_MASK (3 << 6)
#define HORIZ_AUTO_SCALE (1 << 5)
#define PANEL_8TO6_DITHER_ENABLE (1 << 3)
#define PFIT_PGM_RATIOS 0x61234
#define PFIT_VERT_SCALE_MASK 0xfff00000
#define PFIT_HORIZ_SCALE_MASK 0x0000fff0
#define PFIT_AUTO_RATIOS 0x61238
#define DPLL_A 0x06014
#define DPLL_B 0x06018
#define DPLL_VCO_ENABLE (1 << 31)
#define DPLL_DVO_HIGH_SPEED (1 << 30)
#define DPLL_SYNCLOCK_ENABLE (1 << 29)
#define DPLL_VGA_MODE_DIS (1 << 28)
#define DPLLB_MODE_DAC_SERIAL (1 << 26) /* i915 */
#define DPLLB_MODE_LVDS (2 << 26) /* i915 */
#define DPLL_MODE_MASK (3 << 26)
#define DPLL_DAC_SERIAL_P2_CLOCK_DIV_10 (0 << 24) /* i915 */
#define DPLL_DAC_SERIAL_P2_CLOCK_DIV_5 (1 << 24) /* i915 */
#define DPLLB_LVDS_P2_CLOCK_DIV_14 (0 << 24) /* i915 */
#define DPLLB_LVDS_P2_CLOCK_DIV_7 (1 << 24) /* i915 */
#define DPLL_P2_CLOCK_DIV_MASK 0x03000000 /* i915 */
#define DPLL_FPA0h1_P1_POST_DIV_MASK 0x00ff0000 /* i915 */
#define DPLL_LOCK (1 << 15) /* CDV */
/*
* The i830 generation, in DAC/serial mode, defines p1 as two plus this
* bitfield, or just 2 if PLL_P1_DIVIDE_BY_TWO is set.
*/
# define DPLL_FPA01_P1_POST_DIV_MASK_I830 0x001f0000
/*
* The i830 generation, in LVDS mode, defines P1 as the bit number set within
* this field (only one bit may be set).
*/
#define DPLL_FPA01_P1_POST_DIV_MASK_I830_LVDS 0x003f0000
#define DPLL_FPA01_P1_POST_DIV_SHIFT 16
#define PLL_P2_DIVIDE_BY_4 (1 << 23) /* i830, required
* in DVO non-gang */
# define PLL_P1_DIVIDE_BY_TWO (1 << 21) /* i830 */
#define PLL_REF_INPUT_DREFCLK (0 << 13)
#define PLL_REF_INPUT_TVCLKINA (1 << 13) /* i830 */
#define PLL_REF_INPUT_TVCLKINBC (2 << 13) /* SDVO
* TVCLKIN */
#define PLLB_REF_INPUT_SPREADSPECTRUMIN (3 << 13)
#define PLL_REF_INPUT_MASK (3 << 13)
#define PLL_LOAD_PULSE_PHASE_SHIFT 9
/*
* Parallel to Serial Load Pulse phase selection.
* Selects the phase for the 10X DPLL clock for the PCIe
* digital display port. The range is 4 to 13; 10 or more
* is just a flip delay. The default is 6
*/
#define PLL_LOAD_PULSE_PHASE_MASK (0xf << PLL_LOAD_PULSE_PHASE_SHIFT)
#define DISPLAY_RATE_SELECT_FPA1 (1 << 8)
/*
* SDVO multiplier for 945G/GM. Not used on 965.
*
* DPLL_MD_UDI_MULTIPLIER_MASK
*/
#define SDVO_MULTIPLIER_MASK 0x000000ff
#define SDVO_MULTIPLIER_SHIFT_HIRES 4
#define SDVO_MULTIPLIER_SHIFT_VGA 0
/*
* PLL_MD
*/
/* Pipe A SDVO/UDI clock multiplier/divider register for G965. */
#define DPLL_A_MD 0x0601c
/* Pipe B SDVO/UDI clock multiplier/divider register for G965. */
#define DPLL_B_MD 0x06020
/*
* UDI pixel divider, controlling how many pixels are stuffed into a packet.
*
* Value is pixels minus 1. Must be set to 1 pixel for SDVO.
*/
#define DPLL_MD_UDI_DIVIDER_MASK 0x3f000000
#define DPLL_MD_UDI_DIVIDER_SHIFT 24
/* UDI pixel divider for VGA, same as DPLL_MD_UDI_DIVIDER_MASK. */
#define DPLL_MD_VGA_UDI_DIVIDER_MASK 0x003f0000
#define DPLL_MD_VGA_UDI_DIVIDER_SHIFT 16
/*
* SDVO/UDI pixel multiplier.
*
* SDVO requires that the bus clock rate be between 1 and 2 Ghz, and the bus
* clock rate is 10 times the DPLL clock. At low resolution/refresh rate
* modes, the bus rate would be below the limits, so SDVO allows for stuffing
* dummy bytes in the datastream at an increased clock rate, with both sides of
* the link knowing how many bytes are fill.
*
* So, for a mode with a dotclock of 65Mhz, we would want to double the clock
* rate to 130Mhz to get a bus rate of 1.30Ghz. The DPLL clock rate would be
* set to 130Mhz, and the SDVO multiplier set to 2x in this register and
* through an SDVO command.
*
* This register field has values of multiplication factor minus 1, with
* a maximum multiplier of 5 for SDVO.
*/
#define DPLL_MD_UDI_MULTIPLIER_MASK 0x00003f00
#define DPLL_MD_UDI_MULTIPLIER_SHIFT 8
/*
* SDVO/UDI pixel multiplier for VGA, same as DPLL_MD_UDI_MULTIPLIER_MASK.
* This best be set to the default value (3) or the CRT won't work. No,
* I don't entirely understand what this does...
*/
#define DPLL_MD_VGA_UDI_MULTIPLIER_MASK 0x0000003f
#define DPLL_MD_VGA_UDI_MULTIPLIER_SHIFT 0
#define DPLL_TEST 0x606c
#define DPLLB_TEST_SDVO_DIV_1 (0 << 22)
#define DPLLB_TEST_SDVO_DIV_2 (1 << 22)
#define DPLLB_TEST_SDVO_DIV_4 (2 << 22)
#define DPLLB_TEST_SDVO_DIV_MASK (3 << 22)
#define DPLLB_TEST_N_BYPASS (1 << 19)
#define DPLLB_TEST_M_BYPASS (1 << 18)
#define DPLLB_INPUT_BUFFER_ENABLE (1 << 16)
#define DPLLA_TEST_N_BYPASS (1 << 3)
#define DPLLA_TEST_M_BYPASS (1 << 2)
#define DPLLA_INPUT_BUFFER_ENABLE (1 << 0)
#define ADPA 0x61100
#define ADPA_DAC_ENABLE (1 << 31)
#define ADPA_DAC_DISABLE 0
#define ADPA_PIPE_SELECT_MASK (1 << 30)
#define ADPA_PIPE_A_SELECT 0
#define ADPA_PIPE_B_SELECT (1 << 30)
#define ADPA_USE_VGA_HVPOLARITY (1 << 15)
#define ADPA_SETS_HVPOLARITY 0
#define ADPA_VSYNC_CNTL_DISABLE (1 << 11)
#define ADPA_VSYNC_CNTL_ENABLE 0
#define ADPA_HSYNC_CNTL_DISABLE (1 << 10)
#define ADPA_HSYNC_CNTL_ENABLE 0
#define ADPA_VSYNC_ACTIVE_HIGH (1 << 4)
#define ADPA_VSYNC_ACTIVE_LOW 0
#define ADPA_HSYNC_ACTIVE_HIGH (1 << 3)
#define ADPA_HSYNC_ACTIVE_LOW 0
#define FPA0 0x06040
#define FPA1 0x06044
#define FPB0 0x06048
#define FPB1 0x0604c
#define FP_N_DIV_MASK 0x003f0000
#define FP_N_DIV_SHIFT 16
#define FP_M1_DIV_MASK 0x00003f00
#define FP_M1_DIV_SHIFT 8
#define FP_M2_DIV_MASK 0x0000003f
#define FP_M2_DIV_SHIFT 0
#define PORT_HOTPLUG_EN 0x61110
#define HDMIB_HOTPLUG_INT_EN (1 << 29)
#define HDMIC_HOTPLUG_INT_EN (1 << 28)
#define HDMID_HOTPLUG_INT_EN (1 << 27)
#define SDVOB_HOTPLUG_INT_EN (1 << 26)
#define SDVOC_HOTPLUG_INT_EN (1 << 25)
#define TV_HOTPLUG_INT_EN (1 << 18)
#define CRT_HOTPLUG_INT_EN (1 << 9)
#define CRT_HOTPLUG_FORCE_DETECT (1 << 3)
/* CDV.. */
#define CRT_HOTPLUG_ACTIVATION_PERIOD_64 (1 << 8)
#define CRT_HOTPLUG_DAC_ON_TIME_2M (0 << 7)
#define CRT_HOTPLUG_DAC_ON_TIME_4M (1 << 7)
#define CRT_HOTPLUG_VOLTAGE_COMPARE_40 (0 << 5)
#define CRT_HOTPLUG_VOLTAGE_COMPARE_50 (1 << 5)
#define CRT_HOTPLUG_VOLTAGE_COMPARE_60 (2 << 5)
#define CRT_HOTPLUG_VOLTAGE_COMPARE_70 (3 << 5)
#define CRT_HOTPLUG_VOLTAGE_COMPARE_MASK (3 << 5)
#define CRT_HOTPLUG_DETECT_DELAY_1G (0 << 4)
#define CRT_HOTPLUG_DETECT_DELAY_2G (1 << 4)
#define CRT_HOTPLUG_DETECT_VOLTAGE_325MV (0 << 2)
#define CRT_HOTPLUG_DETECT_VOLTAGE_475MV (1 << 2)
#define CRT_HOTPLUG_DETECT_MASK 0x000000F8
#define PORT_HOTPLUG_STAT 0x61114
#define CRT_HOTPLUG_INT_STATUS (1 << 11)
#define TV_HOTPLUG_INT_STATUS (1 << 10)
#define CRT_HOTPLUG_MONITOR_MASK (3 << 8)
#define CRT_HOTPLUG_MONITOR_COLOR (3 << 8)
#define CRT_HOTPLUG_MONITOR_MONO (2 << 8)
#define CRT_HOTPLUG_MONITOR_NONE (0 << 8)
#define SDVOC_HOTPLUG_INT_STATUS (1 << 7)
#define SDVOB_HOTPLUG_INT_STATUS (1 << 6)
#define SDVOB 0x61140
#define SDVOC 0x61160
#define SDVO_ENABLE (1 << 31)
#define SDVO_PIPE_B_SELECT (1 << 30)
#define SDVO_STALL_SELECT (1 << 29)
#define SDVO_INTERRUPT_ENABLE (1 << 26)
#define SDVO_COLOR_RANGE_16_235 (1 << 8)
#define SDVO_AUDIO_ENABLE (1 << 6)
/**
* 915G/GM SDVO pixel multiplier.
*
* Programmed value is multiplier - 1, up to 5x.
*
* DPLL_MD_UDI_MULTIPLIER_MASK
*/
#define SDVO_PORT_MULTIPLY_MASK (7 << 23)
#define SDVO_PORT_MULTIPLY_SHIFT 23
#define SDVO_PHASE_SELECT_MASK (15 << 19)
#define SDVO_PHASE_SELECT_DEFAULT (6 << 19)
#define SDVO_CLOCK_OUTPUT_INVERT (1 << 18)
#define SDVOC_GANG_MODE (1 << 16)
#define SDVO_BORDER_ENABLE (1 << 7)
#define SDVOB_PCIE_CONCURRENCY (1 << 3)
#define SDVO_DETECTED (1 << 2)
/* Bits to be preserved when writing */
#define SDVOB_PRESERVE_MASK ((1 << 17) | (1 << 16) | (1 << 14))
#define SDVOC_PRESERVE_MASK (1 << 17)
/*
* This register controls the LVDS output enable, pipe selection, and data
* format selection.
*
* All of the clock/data pairs are force powered down by power sequencing.
*/
#define LVDS 0x61180
/*
* Enables the LVDS port. This bit must be set before DPLLs are enabled, as
* the DPLL semantics change when the LVDS is assigned to that pipe.
*/
#define LVDS_PORT_EN (1 << 31)
/* Selects pipe B for LVDS data. Must be set on pre-965. */
#define LVDS_PIPEB_SELECT (1 << 30)
/* Turns on border drawing to allow centered display. */
#define LVDS_BORDER_EN (1 << 15)
/*
* Enables the A0-A2 data pairs and CLKA, containing 18 bits of color data per
* pixel.
*/
#define LVDS_A0A2_CLKA_POWER_MASK (3 << 8)
#define LVDS_A0A2_CLKA_POWER_DOWN (0 << 8)
#define LVDS_A0A2_CLKA_POWER_UP (3 << 8)
/*
* Controls the A3 data pair, which contains the additional LSBs for 24 bit
* mode. Only enabled if LVDS_A0A2_CLKA_POWER_UP also indicates it should be
* on.
*/
#define LVDS_A3_POWER_MASK (3 << 6)
#define LVDS_A3_POWER_DOWN (0 << 6)
#define LVDS_A3_POWER_UP (3 << 6)
/*
* Controls the CLKB pair. This should only be set when LVDS_B0B3_POWER_UP
* is set.
*/
#define LVDS_CLKB_POWER_MASK (3 << 4)
#define LVDS_CLKB_POWER_DOWN (0 << 4)
#define LVDS_CLKB_POWER_UP (3 << 4)
/*
* Controls the B0-B3 data pairs. This must be set to match the DPLL p2
* setting for whether we are in dual-channel mode. The B3 pair will
* additionally only be powered up when LVDS_A3_POWER_UP is set.
*/
#define LVDS_B0B3_POWER_MASK (3 << 2)
#define LVDS_B0B3_POWER_DOWN (0 << 2)
#define LVDS_B0B3_POWER_UP (3 << 2)
#define PIPEACONF 0x70008
#define PIPEACONF_ENABLE (1 << 31)
#define PIPEACONF_DISABLE 0
#define PIPEACONF_DOUBLE_WIDE (1 << 30)
#define PIPECONF_ACTIVE (1 << 30)
#define PIPECONF_DSIPLL_LOCK (1 << 29)
#define PIPEACONF_SINGLE_WIDE 0
#define PIPEACONF_PIPE_UNLOCKED 0
#define PIPEACONF_DSR (1 << 26)
#define PIPEACONF_PIPE_LOCKED (1 << 25)
#define PIPEACONF_PALETTE 0
#define PIPECONF_FORCE_BORDER (1 << 25)
#define PIPEACONF_GAMMA (1 << 24)
#define PIPECONF_PROGRESSIVE (0 << 21)
#define PIPECONF_INTERLACE_W_FIELD_INDICATION (6 << 21)
#define PIPECONF_INTERLACE_FIELD_0_ONLY (7 << 21)
#define PIPECONF_PLANE_OFF (1 << 19)
#define PIPECONF_CURSOR_OFF (1 << 18)
#define PIPEBCONF 0x71008
#define PIPEBCONF_ENABLE (1 << 31)
#define PIPEBCONF_DISABLE 0
#define PIPEBCONF_DOUBLE_WIDE (1 << 30)
#define PIPEBCONF_DISABLE 0
#define PIPEBCONF_GAMMA (1 << 24)
#define PIPEBCONF_PALETTE 0
#define PIPECCONF 0x72008
#define PIPEBGCMAXRED 0x71010
#define PIPEBGCMAXGREEN 0x71014
#define PIPEBGCMAXBLUE 0x71018
#define PIPEASTAT 0x70024
#define PIPEBSTAT 0x71024
#define PIPECSTAT 0x72024
#define PIPE_VBLANK_INTERRUPT_STATUS (1UL << 1)
#define PIPE_START_VBLANK_INTERRUPT_STATUS (1UL << 2)
#define PIPE_VBLANK_CLEAR (1 << 1)
#define PIPE_VBLANK_STATUS (1 << 1)
#define PIPE_TE_STATUS (1UL << 6)
#define PIPE_DPST_EVENT_STATUS (1UL << 7)
#define PIPE_VSYNC_CLEAR (1UL << 9)
#define PIPE_VSYNC_STATUS (1UL << 9)
#define PIPE_HDMI_AUDIO_UNDERRUN_STATUS (1UL << 10)
#define PIPE_HDMI_AUDIO_BUFFER_DONE_STATUS (1UL << 11)
#define PIPE_VBLANK_INTERRUPT_ENABLE (1UL << 17)
#define PIPE_START_VBLANK_INTERRUPT_ENABLE (1UL << 18)
#define PIPE_TE_ENABLE (1UL << 22)
#define PIPE_LEGACY_BLC_EVENT_ENABLE (1UL << 22)
#define PIPE_DPST_EVENT_ENABLE (1UL << 23)
#define PIPE_VSYNC_ENABL (1UL << 25)
#define PIPE_HDMI_AUDIO_UNDERRUN (1UL << 26)
#define PIPE_HDMI_AUDIO_BUFFER_DONE (1UL << 27)
#define PIPE_FIFO_UNDERRUN (1UL << 31)
#define PIPE_HDMI_AUDIO_INT_MASK (PIPE_HDMI_AUDIO_UNDERRUN | \
PIPE_HDMI_AUDIO_BUFFER_DONE)
#define PIPE_EVENT_MASK ((1 << 29)|(1 << 28)|(1 << 27)|(1 << 26)|(1 << 24)|(1 << 23)|(1 << 22)|(1 << 21)|(1 << 20)|(1 << 16))
#define PIPE_VBLANK_MASK ((1 << 25)|(1 << 24)|(1 << 18)|(1 << 17))
#define HISTOGRAM_INT_CONTROL 0x61268
#define HISTOGRAM_BIN_DATA 0X61264
#define HISTOGRAM_LOGIC_CONTROL 0x61260
#define PWM_CONTROL_LOGIC 0x61250
#define PIPE_HOTPLUG_INTERRUPT_STATUS (1UL << 10)
#define HISTOGRAM_INTERRUPT_ENABLE (1UL << 31)
#define HISTOGRAM_LOGIC_ENABLE (1UL << 31)
#define PWM_LOGIC_ENABLE (1UL << 31)
#define PWM_PHASEIN_ENABLE (1UL << 25)
#define PWM_PHASEIN_INT_ENABLE (1UL << 24)
#define PWM_PHASEIN_VB_COUNT 0x00001f00
#define PWM_PHASEIN_INC 0x0000001f
#define HISTOGRAM_INT_CTRL_CLEAR (1UL << 30)
#define DPST_YUV_LUMA_MODE 0
struct dpst_ie_histogram_control {
union {
uint32_t data;
struct {
uint32_t bin_reg_index:7;
uint32_t reserved:4;
uint32_t bin_reg_func_select:1;
uint32_t sync_to_phase_in:1;
uint32_t alt_enhancement_mode:2;
uint32_t reserved1:1;
uint32_t sync_to_phase_in_count:8;
uint32_t histogram_mode_select:1;
uint32_t reserved2:4;
uint32_t ie_pipe_assignment:1;
uint32_t ie_mode_table_enabled:1;
uint32_t ie_histogram_enable:1;
};
};
};
struct dpst_guardband {
union {
uint32_t data;
struct {
uint32_t guardband:22;
uint32_t guardband_interrupt_delay:8;
uint32_t interrupt_status:1;
uint32_t interrupt_enable:1;
};
};
};
#define PIPEAFRAMEHIGH 0x70040
#define PIPEAFRAMEPIXEL 0x70044
#define PIPEBFRAMEHIGH 0x71040
#define PIPEBFRAMEPIXEL 0x71044
#define PIPECFRAMEHIGH 0x72040
#define PIPECFRAMEPIXEL 0x72044
#define PIPE_FRAME_HIGH_MASK 0x0000ffff
#define PIPE_FRAME_HIGH_SHIFT 0
#define PIPE_FRAME_LOW_MASK 0xff000000
#define PIPE_FRAME_LOW_SHIFT 24
#define PIPE_PIXEL_MASK 0x00ffffff
#define PIPE_PIXEL_SHIFT 0
#define FW_BLC_SELF 0x20e0
#define FW_BLC_SELF_EN (1<<15)
#define DSPARB 0x70030
#define DSPFW1 0x70034
#define DSP_FIFO_SR_WM_MASK 0xFF800000
#define DSP_FIFO_SR_WM_SHIFT 23
#define CURSOR_B_FIFO_WM_MASK 0x003F0000
#define CURSOR_B_FIFO_WM_SHIFT 16
#define DSPFW2 0x70038
#define CURSOR_A_FIFO_WM_MASK 0x3F00
#define CURSOR_A_FIFO_WM_SHIFT 8
#define DSP_PLANE_C_FIFO_WM_MASK 0x7F
#define DSP_PLANE_C_FIFO_WM_SHIFT 0
#define DSPFW3 0x7003c
#define DSPFW4 0x70050
#define DSPFW5 0x70054
#define DSP_PLANE_B_FIFO_WM1_SHIFT 24
#define DSP_PLANE_A_FIFO_WM1_SHIFT 16
#define CURSOR_B_FIFO_WM1_SHIFT 8
#define CURSOR_FIFO_SR_WM1_SHIFT 0
#define DSPFW6 0x70058
#define DSPCHICKENBIT 0x70400
#define DSPACNTR 0x70180
#define DSPBCNTR 0x71180
#define DSPCCNTR 0x72180
#define DISPLAY_PLANE_ENABLE (1 << 31)
#define DISPLAY_PLANE_DISABLE 0
#define DISPPLANE_GAMMA_ENABLE (1 << 30)
#define DISPPLANE_GAMMA_DISABLE 0
#define DISPPLANE_PIXFORMAT_MASK (0xf << 26)
#define DISPPLANE_8BPP (0x2 << 26)
#define DISPPLANE_15_16BPP (0x4 << 26)
#define DISPPLANE_16BPP (0x5 << 26)
#define DISPPLANE_32BPP_NO_ALPHA (0x6 << 26)
#define DISPPLANE_32BPP (0x7 << 26)
#define DISPPLANE_STEREO_ENABLE (1 << 25)
#define DISPPLANE_STEREO_DISABLE 0
#define DISPPLANE_SEL_PIPE_MASK (1 << 24)
#define DISPPLANE_SEL_PIPE_POS 24
#define DISPPLANE_SEL_PIPE_A 0
#define DISPPLANE_SEL_PIPE_B (1 << 24)
#define DISPPLANE_SRC_KEY_ENABLE (1 << 22)
#define DISPPLANE_SRC_KEY_DISABLE 0
#define DISPPLANE_LINE_DOUBLE (1 << 20)
#define DISPPLANE_NO_LINE_DOUBLE 0
#define DISPPLANE_STEREO_POLARITY_FIRST 0
#define DISPPLANE_STEREO_POLARITY_SECOND (1 << 18)
/* plane B only */
#define DISPPLANE_ALPHA_TRANS_ENABLE (1 << 15)
#define DISPPLANE_ALPHA_TRANS_DISABLE 0
#define DISPPLANE_SPRITE_ABOVE_DISPLAYA 0
#define DISPPLANE_SPRITE_ABOVE_OVERLAY (1)
#define DISPPLANE_BOTTOM (4)
#define DSPABASE 0x70184
#define DSPALINOFF 0x70184
#define DSPASTRIDE 0x70188
#define DSPBBASE 0x71184
#define DSPBLINOFF 0X71184
#define DSPBADDR DSPBBASE
#define DSPBSTRIDE 0x71188
#define DSPCBASE 0x72184
#define DSPCLINOFF 0x72184
#define DSPCSTRIDE 0x72188
#define DSPAKEYVAL 0x70194
#define DSPAKEYMASK 0x70198
#define DSPAPOS 0x7018C /* reserved */
#define DSPASIZE 0x70190
#define DSPBPOS 0x7118C
#define DSPBSIZE 0x71190
#define DSPCPOS 0x7218C
#define DSPCSIZE 0x72190
#define DSPASURF 0x7019C
#define DSPATILEOFF 0x701A4
#define DSPBSURF 0x7119C
#define DSPBTILEOFF 0x711A4
#define DSPCSURF 0x7219C
#define DSPCTILEOFF 0x721A4
#define DSPCKEYMAXVAL 0x721A0
#define DSPCKEYMINVAL 0x72194
#define DSPCKEYMSK 0x72198
#define VGACNTRL 0x71400
#define VGA_DISP_DISABLE (1 << 31)
#define VGA_2X_MODE (1 << 30)
#define VGA_PIPE_B_SELECT (1 << 29)
/*
* Overlay registers
*/
#define OV_C_OFFSET 0x08000
#define OV_OVADD 0x30000
#define OV_DOVASTA 0x30008
# define OV_PIPE_SELECT ((1 << 6)|(1 << 7))
# define OV_PIPE_SELECT_POS 6
# define OV_PIPE_A 0
# define OV_PIPE_C 1
#define OV_OGAMC5 0x30010
#define OV_OGAMC4 0x30014
#define OV_OGAMC3 0x30018
#define OV_OGAMC2 0x3001C
#define OV_OGAMC1 0x30020
#define OV_OGAMC0 0x30024
#define OVC_OVADD 0x38000
#define OVC_DOVCSTA 0x38008
#define OVC_OGAMC5 0x38010
#define OVC_OGAMC4 0x38014
#define OVC_OGAMC3 0x38018
#define OVC_OGAMC2 0x3801C
#define OVC_OGAMC1 0x38020
#define OVC_OGAMC0 0x38024
/*
* Some BIOS scratch area registers. The 845 (and 830?) store the amount
* of video memory available to the BIOS in SWF1.
*/
#define SWF0 0x71410
#define SWF1 0x71414
#define SWF2 0x71418
#define SWF3 0x7141c
#define SWF4 0x71420
#define SWF5 0x71424
#define SWF6 0x71428
/*
* 855 scratch registers.
*/
#define SWF00 0x70410
#define SWF01 0x70414
#define SWF02 0x70418
#define SWF03 0x7041c
#define SWF04 0x70420
#define SWF05 0x70424
#define SWF06 0x70428
#define SWF10 SWF0
#define SWF11 SWF1
#define SWF12 SWF2
#define SWF13 SWF3
#define SWF14 SWF4
#define SWF15 SWF5
#define SWF16 SWF6
#define SWF30 0x72414
#define SWF31 0x72418
#define SWF32 0x7241c
/*
* Palette registers
*/
#define PALETTE_A 0x0a000
#define PALETTE_B 0x0a800
#define PALETTE_C 0x0ac00
/* Cursor A & B regs */
#define CURACNTR 0x70080
#define CURSOR_MODE_DISABLE 0x00
#define CURSOR_MODE_64_32B_AX 0x07
#define CURSOR_MODE_64_ARGB_AX ((1 << 5) | CURSOR_MODE_64_32B_AX)
#define MCURSOR_GAMMA_ENABLE (1 << 26)
#define CURABASE 0x70084
#define CURAPOS 0x70088
#define CURSOR_POS_MASK 0x007FF
#define CURSOR_POS_SIGN 0x8000
#define CURSOR_X_SHIFT 0
#define CURSOR_Y_SHIFT 16
#define CURBCNTR 0x700c0
#define CURBBASE 0x700c4
#define CURBPOS 0x700c8
#define CURCCNTR 0x700e0
#define CURCBASE 0x700e4
#define CURCPOS 0x700e8
/*
* Interrupt Registers
*/
#define IER 0x020a0
#define IIR 0x020a4
#define IMR 0x020a8
#define ISR 0x020ac
/*
* MOORESTOWN delta registers
*/
#define MRST_DPLL_A 0x0f014
#define MDFLD_DPLL_B 0x0f018
#define MDFLD_INPUT_REF_SEL (1 << 14)
#define MDFLD_VCO_SEL (1 << 16)
#define DPLLA_MODE_LVDS (2 << 26) /* mrst */
#define MDFLD_PLL_LATCHEN (1 << 28)
#define MDFLD_PWR_GATE_EN (1 << 30)
#define MDFLD_P1_MASK (0x1FF << 17)
#define MRST_FPA0 0x0f040
#define MRST_FPA1 0x0f044
#define MDFLD_DPLL_DIV0 0x0f048
#define MDFLD_DPLL_DIV1 0x0f04c
#define MRST_PERF_MODE 0x020f4
/*
* MEDFIELD HDMI registers
*/
#define HDMIPHYMISCCTL 0x61134
#define HDMI_PHY_POWER_DOWN 0x7f
#define HDMIB_CONTROL 0x61140
#define HDMIB_PORT_EN (1 << 31)
#define HDMIB_PIPE_B_SELECT (1 << 30)
#define HDMIB_NULL_PACKET (1 << 9)
#define HDMIB_HDCP_PORT (1 << 5)
/* #define LVDS 0x61180 */
#define MRST_PANEL_8TO6_DITHER_ENABLE (1 << 25)
#define MRST_PANEL_24_DOT_1_FORMAT (1 << 24)
#define LVDS_A3_POWER_UP_0_OUTPUT (1 << 6)
#define MIPI 0x61190
#define MIPI_C 0x62190
#define MIPI_PORT_EN (1 << 31)
/* Turns on border drawing to allow centered display. */
#define SEL_FLOPPED_HSTX (1 << 23)
#define PASS_FROM_SPHY_TO_AFE (1 << 16)
#define MIPI_BORDER_EN (1 << 15)
#define MIPIA_3LANE_MIPIC_1LANE 0x1
#define MIPIA_2LANE_MIPIC_2LANE 0x2
#define TE_TRIGGER_DSI_PROTOCOL (1 << 2)
#define TE_TRIGGER_GPIO_PIN (1 << 3)
#define MIPI_TE_COUNT 0x61194
/* #define PP_CONTROL 0x61204 */
#define POWER_DOWN_ON_RESET (1 << 1)
/* #define PFIT_CONTROL 0x61230 */
#define PFIT_PIPE_SELECT (3 << 29)
#define PFIT_PIPE_SELECT_SHIFT (29)
/* #define BLC_PWM_CTL 0x61254 */
#define MRST_BACKLIGHT_MODULATION_FREQ_SHIFT (16)
#define MRST_BACKLIGHT_MODULATION_FREQ_MASK (0xffff << 16)
/* #define PIPEACONF 0x70008 */
#define PIPEACONF_PIPE_STATE (1 << 30)
/* #define DSPACNTR 0x70180 */
#define MRST_DSPABASE 0x7019c
#define MRST_DSPBBASE 0x7119c
#define MDFLD_DSPCBASE 0x7219c
/*
* Moorestown registers.
*/
/*
* MIPI IP registers
*/
#define MIPIC_REG_OFFSET 0x800
#define DEVICE_READY_REG 0xb000
#define LP_OUTPUT_HOLD (1 << 16)
#define EXIT_ULPS_DEV_READY 0x3
#define LP_OUTPUT_HOLD_RELEASE 0x810000
# define ENTERING_ULPS (2 << 1)
# define EXITING_ULPS (1 << 1)
# define ULPS_MASK (3 << 1)
# define BUS_POSSESSION (1 << 3)
#define INTR_STAT_REG 0xb004
#define RX_SOT_ERROR (1 << 0)
#define RX_SOT_SYNC_ERROR (1 << 1)
#define RX_ESCAPE_MODE_ENTRY_ERROR (1 << 3)
#define RX_LP_TX_SYNC_ERROR (1 << 4)
#define RX_HS_RECEIVE_TIMEOUT_ERROR (1 << 5)
#define RX_FALSE_CONTROL_ERROR (1 << 6)
#define RX_ECC_SINGLE_BIT_ERROR (1 << 7)
#define RX_ECC_MULTI_BIT_ERROR (1 << 8)
#define RX_CHECKSUM_ERROR (1 << 9)
#define RX_DSI_DATA_TYPE_NOT_RECOGNIZED (1 << 10)
#define RX_DSI_VC_ID_INVALID (1 << 11)
#define TX_FALSE_CONTROL_ERROR (1 << 12)
#define TX_ECC_SINGLE_BIT_ERROR (1 << 13)
#define TX_ECC_MULTI_BIT_ERROR (1 << 14)
#define TX_CHECKSUM_ERROR (1 << 15)
#define TX_DSI_DATA_TYPE_NOT_RECOGNIZED (1 << 16)
#define TX_DSI_VC_ID_INVALID (1 << 17)
#define HIGH_CONTENTION (1 << 18)
#define LOW_CONTENTION (1 << 19)
#define DPI_FIFO_UNDER_RUN (1 << 20)
#define HS_TX_TIMEOUT (1 << 21)
#define LP_RX_TIMEOUT (1 << 22)
#define TURN_AROUND_ACK_TIMEOUT (1 << 23)
#define ACK_WITH_NO_ERROR (1 << 24)
#define HS_GENERIC_WR_FIFO_FULL (1 << 27)
#define LP_GENERIC_WR_FIFO_FULL (1 << 28)
#define SPL_PKT_SENT (1 << 30)
#define INTR_EN_REG 0xb008
#define DSI_FUNC_PRG_REG 0xb00c
#define DPI_CHANNEL_NUMBER_POS 0x03
#define DBI_CHANNEL_NUMBER_POS 0x05
#define FMT_DPI_POS 0x07
#define FMT_DBI_POS 0x0A
#define DBI_DATA_WIDTH_POS 0x0D
/* DPI PIXEL FORMATS */
#define RGB_565_FMT 0x01 /* RGB 565 FORMAT */
#define RGB_666_FMT 0x02 /* RGB 666 FORMAT */
#define LRGB_666_FMT 0x03 /* RGB LOOSELY PACKED
* 666 FORMAT
*/
#define RGB_888_FMT 0x04 /* RGB 888 FORMAT */
#define VIRTUAL_CHANNEL_NUMBER_0 0x00 /* Virtual channel 0 */
#define VIRTUAL_CHANNEL_NUMBER_1 0x01 /* Virtual channel 1 */
#define VIRTUAL_CHANNEL_NUMBER_2 0x02 /* Virtual channel 2 */
#define VIRTUAL_CHANNEL_NUMBER_3 0x03 /* Virtual channel 3 */
#define DBI_NOT_SUPPORTED 0x00 /* command mode
* is not supported
*/
#define DBI_DATA_WIDTH_16BIT 0x01 /* 16 bit data */
#define DBI_DATA_WIDTH_9BIT 0x02 /* 9 bit data */
#define DBI_DATA_WIDTH_8BIT 0x03 /* 8 bit data */
#define DBI_DATA_WIDTH_OPT1 0x04 /* option 1 */
#define DBI_DATA_WIDTH_OPT2 0x05 /* option 2 */
#define HS_TX_TIMEOUT_REG 0xb010
#define LP_RX_TIMEOUT_REG 0xb014
#define TURN_AROUND_TIMEOUT_REG 0xb018
#define DEVICE_RESET_REG 0xb01C
#define DPI_RESOLUTION_REG 0xb020
#define RES_V_POS 0x10
#define DBI_RESOLUTION_REG 0xb024 /* Reserved for MDFLD */
#define HORIZ_SYNC_PAD_COUNT_REG 0xb028
#define HORIZ_BACK_PORCH_COUNT_REG 0xb02C
#define HORIZ_FRONT_PORCH_COUNT_REG 0xb030
#define HORIZ_ACTIVE_AREA_COUNT_REG 0xb034
#define VERT_SYNC_PAD_COUNT_REG 0xb038
#define VERT_BACK_PORCH_COUNT_REG 0xb03c
#define VERT_FRONT_PORCH_COUNT_REG 0xb040
#define HIGH_LOW_SWITCH_COUNT_REG 0xb044
#define DPI_CONTROL_REG 0xb048
#define DPI_SHUT_DOWN (1 << 0)
#define DPI_TURN_ON (1 << 1)
#define DPI_COLOR_MODE_ON (1 << 2)
#define DPI_COLOR_MODE_OFF (1 << 3)
#define DPI_BACK_LIGHT_ON (1 << 4)
#define DPI_BACK_LIGHT_OFF (1 << 5)
#define DPI_LP (1 << 6)
#define DPI_DATA_REG 0xb04c
#define DPI_BACK_LIGHT_ON_DATA 0x07
#define DPI_BACK_LIGHT_OFF_DATA 0x17
#define INIT_COUNT_REG 0xb050
#define MAX_RET_PAK_REG 0xb054
#define VIDEO_FMT_REG 0xb058
#define COMPLETE_LAST_PCKT (1 << 2)
#define EOT_DISABLE_REG 0xb05c
#define ENABLE_CLOCK_STOPPING (1 << 1)
#define LP_BYTECLK_REG 0xb060
#define LP_GEN_DATA_REG 0xb064
#define HS_GEN_DATA_REG 0xb068
#define LP_GEN_CTRL_REG 0xb06C
#define HS_GEN_CTRL_REG 0xb070
#define DCS_CHANNEL_NUMBER_POS 0x6
#define MCS_COMMANDS_POS 0x8
#define WORD_COUNTS_POS 0x8
#define MCS_PARAMETER_POS 0x10
#define GEN_FIFO_STAT_REG 0xb074
#define HS_DATA_FIFO_FULL (1 << 0)
#define HS_DATA_FIFO_HALF_EMPTY (1 << 1)
#define HS_DATA_FIFO_EMPTY (1 << 2)
#define LP_DATA_FIFO_FULL (1 << 8)
#define LP_DATA_FIFO_HALF_EMPTY (1 << 9)
#define LP_DATA_FIFO_EMPTY (1 << 10)
#define HS_CTRL_FIFO_FULL (1 << 16)
#define HS_CTRL_FIFO_HALF_EMPTY (1 << 17)
#define HS_CTRL_FIFO_EMPTY (1 << 18)
#define LP_CTRL_FIFO_FULL (1 << 24)
#define LP_CTRL_FIFO_HALF_EMPTY (1 << 25)
#define LP_CTRL_FIFO_EMPTY (1 << 26)
#define DBI_FIFO_EMPTY (1 << 27)
#define DPI_FIFO_EMPTY (1 << 28)
#define HS_LS_DBI_ENABLE_REG 0xb078
#define TXCLKESC_REG 0xb07c
#define DPHY_PARAM_REG 0xb080
#define DBI_BW_CTRL_REG 0xb084
#define CLK_LANE_SWT_REG 0xb088
/*
* MIPI Adapter registers
*/
#define MIPI_CONTROL_REG 0xb104
#define MIPI_2X_CLOCK_BITS ((1 << 0) | (1 << 1))
#define MIPI_DATA_ADDRESS_REG 0xb108
#define MIPI_DATA_LENGTH_REG 0xb10C
#define MIPI_COMMAND_ADDRESS_REG 0xb110
#define MIPI_COMMAND_LENGTH_REG 0xb114
#define MIPI_READ_DATA_RETURN_REG0 0xb118
#define MIPI_READ_DATA_RETURN_REG1 0xb11C
#define MIPI_READ_DATA_RETURN_REG2 0xb120
#define MIPI_READ_DATA_RETURN_REG3 0xb124
#define MIPI_READ_DATA_RETURN_REG4 0xb128
#define MIPI_READ_DATA_RETURN_REG5 0xb12C
#define MIPI_READ_DATA_RETURN_REG6 0xb130
#define MIPI_READ_DATA_RETURN_REG7 0xb134
#define MIPI_READ_DATA_VALID_REG 0xb138
/* DBI COMMANDS */
#define soft_reset 0x01
/*
* The display module performs a software reset.
* Registers are written with their SW Reset default values.
*/
#define get_power_mode 0x0a
/*
* The display module returns the current power mode
*/
#define get_address_mode 0x0b
/*
* The display module returns the current status.
*/
#define get_pixel_format 0x0c
/*
* This command gets the pixel format for the RGB image data
* used by the interface.
*/
#define get_display_mode 0x0d
/*
* The display module returns the Display Image Mode status.
*/
#define get_signal_mode 0x0e
/*
* The display module returns the Display Signal Mode.
*/
#define get_diagnostic_result 0x0f
/*
* The display module returns the self-diagnostic results following
* a Sleep Out command.
*/
#define enter_sleep_mode 0x10
/*
* This command causes the display module to enter the Sleep mode.
* In this mode, all unnecessary blocks inside the display module are
* disabled except interface communication. This is the lowest power
* mode the display module supports.
*/
#define exit_sleep_mode 0x11
/*
* This command causes the display module to exit Sleep mode.
* All blocks inside the display module are enabled.
*/
#define enter_partial_mode 0x12
/*
* This command causes the display module to enter the Partial Display
* Mode. The Partial Display Mode window is described by the
* set_partial_area command.
*/
#define enter_normal_mode 0x13
/*
* This command causes the display module to enter the Normal mode.
* Normal Mode is defined as Partial Display mode and Scroll mode are off
*/
#define exit_invert_mode 0x20
/*
* This command causes the display module to stop inverting the image
* data on the display device. The frame memory contents remain unchanged.
* No status bits are changed.
*/
#define enter_invert_mode 0x21
/*
* This command causes the display module to invert the image data only on
* the display device. The frame memory contents remain unchanged.
* No status bits are changed.
*/
#define set_gamma_curve 0x26
/*
* This command selects the desired gamma curve for the display device.
* Four fixed gamma curves are defined in section DCS spec.
*/
#define set_display_off 0x28
/* ************************************************************************* *\
This command causes the display module to stop displaying the image data
on the display device. The frame memory contents remain unchanged.
No status bits are changed.
\* ************************************************************************* */
#define set_display_on 0x29
/* ************************************************************************* *\
This command causes the display module to start displaying the image data
on the display device. The frame memory contents remain unchanged.
No status bits are changed.
\* ************************************************************************* */
#define set_column_address 0x2a
/*
* This command defines the column extent of the frame memory accessed by
* the hostprocessor with the read_memory_continue and
* write_memory_continue commands.
* No status bits are changed.
*/
#define set_page_addr 0x2b
/*
* This command defines the page extent of the frame memory accessed by
* the host processor with the write_memory_continue and
* read_memory_continue command.
* No status bits are changed.
*/
#define write_mem_start 0x2c
/*
* This command transfers image data from the host processor to the
* display modules frame memory starting at the pixel location specified
* by preceding set_column_address and set_page_address commands.
*/
#define set_partial_area 0x30
/*
* This command defines the Partial Display mode s display area.
* There are two parameters associated with this command, the first
* defines the Start Row (SR) and the second the End Row (ER). SR and ER
* refer to the Frame Memory Line Pointer.
*/
#define set_scroll_area 0x33
/*
* This command defines the display modules Vertical Scrolling Area.
*/
#define set_tear_off 0x34
/*
* This command turns off the display modules Tearing Effect output
* signal on the TE signal line.
*/
#define set_tear_on 0x35
/*
* This command turns on the display modules Tearing Effect output signal
* on the TE signal line.
*/
#define set_address_mode 0x36
/*
* This command sets the data order for transfers from the host processor
* to display modules frame memory,bits B[7:5] and B3, and from the
* display modules frame memory to the display device, bits B[2:0] and B4.
*/
#define set_scroll_start 0x37
/*
* This command sets the start of the vertical scrolling area in the frame
* memory. The vertical scrolling area is fully defined when this command
* is used with the set_scroll_area command The set_scroll_start command
* has one parameter, the Vertical Scroll Pointer. The VSP defines the
* line in the frame memory that is written to the display device as the
* first line of the vertical scroll area.
*/
#define exit_idle_mode 0x38
/*
* This command causes the display module to exit Idle mode.
*/
#define enter_idle_mode 0x39
/*
* This command causes the display module to enter Idle Mode.
* In Idle Mode, color expression is reduced. Colors are shown on the
* display device using the MSB of each of the R, G and B color
* components in the frame memory
*/
#define set_pixel_format 0x3a
/*
* This command sets the pixel format for the RGB image data used by the
* interface.
* Bits D[6:4] DPI Pixel Format Definition
* Bits D[2:0] DBI Pixel Format Definition
* Bits D7 and D3 are not used.
*/
#define DCS_PIXEL_FORMAT_3bpp 0x1
#define DCS_PIXEL_FORMAT_8bpp 0x2
#define DCS_PIXEL_FORMAT_12bpp 0x3
#define DCS_PIXEL_FORMAT_16bpp 0x5
#define DCS_PIXEL_FORMAT_18bpp 0x6
#define DCS_PIXEL_FORMAT_24bpp 0x7
#define write_mem_cont 0x3c
/*
* This command transfers image data from the host processor to the
* display module's frame memory continuing from the pixel location
* following the previous write_memory_continue or write_memory_start
* command.
*/
#define set_tear_scanline 0x44
/*
* This command turns on the display modules Tearing Effect output signal
* on the TE signal line when the display module reaches line N.
*/
#define get_scanline 0x45
/*
* The display module returns the current scanline, N, used to update the
* display device. The total number of scanlines on a display device is
* defined as VSYNC + VBP + VACT + VFP.The first scanline is defined as
* the first line of V Sync and is denoted as Line 0.
* When in Sleep Mode, the value returned by get_scanline is undefined.
*/
/* MCS or Generic COMMANDS */
/* MCS/generic data type */
#define GEN_SHORT_WRITE_0 0x03 /* generic short write, no parameters */
#define GEN_SHORT_WRITE_1 0x13 /* generic short write, 1 parameters */
#define GEN_SHORT_WRITE_2 0x23 /* generic short write, 2 parameters */
#define GEN_READ_0 0x04 /* generic read, no parameters */
#define GEN_READ_1 0x14 /* generic read, 1 parameters */
#define GEN_READ_2 0x24 /* generic read, 2 parameters */
#define GEN_LONG_WRITE 0x29 /* generic long write */
#define MCS_SHORT_WRITE_0 0x05 /* MCS short write, no parameters */
#define MCS_SHORT_WRITE_1 0x15 /* MCS short write, 1 parameters */
#define MCS_READ 0x06 /* MCS read, no parameters */
#define MCS_LONG_WRITE 0x39 /* MCS long write */
/* MCS/generic commands */
/* TPO MCS */
#define write_display_profile 0x50
#define write_display_brightness 0x51
#define write_ctrl_display 0x53
#define write_ctrl_cabc 0x55
#define UI_IMAGE 0x01
#define STILL_IMAGE 0x02
#define MOVING_IMAGE 0x03
#define write_hysteresis 0x57
#define write_gamma_setting 0x58
#define write_cabc_min_bright 0x5e
#define write_kbbc_profile 0x60
/* TMD MCS */
#define tmd_write_display_brightness 0x8c
/*
* This command is used to control ambient light, panel backlight
* brightness and gamma settings.
*/
#define BRIGHT_CNTL_BLOCK_ON (1 << 5)
#define AMBIENT_LIGHT_SENSE_ON (1 << 4)
#define DISPLAY_DIMMING_ON (1 << 3)
#define BACKLIGHT_ON (1 << 2)
#define DISPLAY_BRIGHTNESS_AUTO (1 << 1)
#define GAMMA_AUTO (1 << 0)
/* DCS Interface Pixel Formats */
#define DCS_PIXEL_FORMAT_3BPP 0x1
#define DCS_PIXEL_FORMAT_8BPP 0x2
#define DCS_PIXEL_FORMAT_12BPP 0x3
#define DCS_PIXEL_FORMAT_16BPP 0x5
#define DCS_PIXEL_FORMAT_18BPP 0x6
#define DCS_PIXEL_FORMAT_24BPP 0x7
/* ONE PARAMETER READ DATA */
#define addr_mode_data 0xfc
#define diag_res_data 0x00
#define disp_mode_data 0x23
#define pxl_fmt_data 0x77
#define pwr_mode_data 0x74
#define sig_mode_data 0x00
/* TWO PARAMETERS READ DATA */
#define scanline_data1 0xff
#define scanline_data2 0xff
#define NON_BURST_MODE_SYNC_PULSE 0x01 /* Non Burst Mode
* with Sync Pulse
*/
#define NON_BURST_MODE_SYNC_EVENTS 0x02 /* Non Burst Mode
* with Sync events
*/
#define BURST_MODE 0x03 /* Burst Mode */
#define DBI_COMMAND_BUFFER_SIZE 0x240 /* 0x32 */ /* 0x120 */
/* Allocate at least
* 0x100 Byte with 32
* byte alignment
*/
#define DBI_DATA_BUFFER_SIZE 0x120 /* Allocate at least
* 0x100 Byte with 32
* byte alignment
*/
#define DBI_CB_TIME_OUT 0xFFFF
#define GEN_FB_TIME_OUT 2000
#define SKU_83 0x01
#define SKU_100 0x02
#define SKU_100L 0x04
#define SKU_BYPASS 0x08
/* Some handy macros for playing with bitfields. */
#define PSB_MASK(high, low) (((1<<((high)-(low)+1))-1)<<(low))
#define SET_FIELD(value, field) (((value) << field ## _SHIFT) & field ## _MASK)
#define GET_FIELD(word, field) (((word) & field ## _MASK) >> field ## _SHIFT)
#define _PIPE(pipe, a, b) ((a) + (pipe)*((b)-(a)))
/* PCI config space */
#define SB_PCKT 0x02100 /* cedarview */
# define SB_OPCODE_MASK PSB_MASK(31, 16)
# define SB_OPCODE_SHIFT 16
# define SB_OPCODE_READ 0
# define SB_OPCODE_WRITE 1
# define SB_DEST_MASK PSB_MASK(15, 8)
# define SB_DEST_SHIFT 8
# define SB_DEST_DPLL 0x88
# define SB_BYTE_ENABLE_MASK PSB_MASK(7, 4)
# define SB_BYTE_ENABLE_SHIFT 4
# define SB_BUSY (1 << 0)
#define DSPCLK_GATE_D 0x6200
# define VRHUNIT_CLOCK_GATE_DISABLE (1 << 28) /* Fixed value on CDV */
# define DPOUNIT_CLOCK_GATE_DISABLE (1 << 11)
# define DPIOUNIT_CLOCK_GATE_DISABLE (1 << 6)
# define DPUNIT_PIPEB_GATE_DISABLE (1 << 30)
# define DPUNIT_PIPEA_GATE_DISABLE (1 << 25)
# define DPCUNIT_CLOCK_GATE_DISABLE (1 << 24)
# define DPLSUNIT_CLOCK_GATE_DISABLE (1 << 13)
#define RAMCLK_GATE_D 0x6210
/* 32-bit value read/written from the DPIO reg. */
#define SB_DATA 0x02104 /* cedarview */
/* 32-bit address of the DPIO reg to be read/written. */
#define SB_ADDR 0x02108 /* cedarview */
#define DPIO_CFG 0x02110 /* cedarview */
# define DPIO_MODE_SELECT_1 (1 << 3)
# define DPIO_MODE_SELECT_0 (1 << 2)
# define DPIO_SFR_BYPASS (1 << 1)
/* reset is active low */
# define DPIO_CMN_RESET_N (1 << 0)
/* Cedarview sideband registers */
#define _SB_M_A 0x8008
#define _SB_M_B 0x8028
#define SB_M(pipe) _PIPE(pipe, _SB_M_A, _SB_M_B)
# define SB_M_DIVIDER_MASK (0xFF << 24)
# define SB_M_DIVIDER_SHIFT 24
#define _SB_N_VCO_A 0x8014
#define _SB_N_VCO_B 0x8034
#define SB_N_VCO(pipe) _PIPE(pipe, _SB_N_VCO_A, _SB_N_VCO_B)
#define SB_N_VCO_SEL_MASK PSB_MASK(31, 30)
#define SB_N_VCO_SEL_SHIFT 30
#define SB_N_DIVIDER_MASK PSB_MASK(29, 26)
#define SB_N_DIVIDER_SHIFT 26
#define SB_N_CB_TUNE_MASK PSB_MASK(25, 24)
#define SB_N_CB_TUNE_SHIFT 24
/* the bit 14:13 is used to select between the different reference clock for Pipe A/B */
#define SB_REF_DPLLA 0x8010
#define SB_REF_DPLLB 0x8030
#define REF_CLK_MASK (0x3 << 13)
#define REF_CLK_CORE (0 << 13)
#define REF_CLK_DPLL (1 << 13)
#define REF_CLK_DPLLA (2 << 13)
/* For the DPLL B, it will use the reference clk from DPLL A when using (2 << 13) */
#define _SB_REF_A 0x8018
#define _SB_REF_B 0x8038
#define SB_REF_SFR(pipe) _PIPE(pipe, _SB_REF_A, _SB_REF_B)
#define _SB_P_A 0x801c
#define _SB_P_B 0x803c
#define SB_P(pipe) _PIPE(pipe, _SB_P_A, _SB_P_B)
#define SB_P2_DIVIDER_MASK PSB_MASK(31, 30)
#define SB_P2_DIVIDER_SHIFT 30
#define SB_P2_10 0 /* HDMI, DP, DAC */
#define SB_P2_5 1 /* DAC */
#define SB_P2_14 2 /* LVDS single */
#define SB_P2_7 3 /* LVDS double */
#define SB_P1_DIVIDER_MASK PSB_MASK(15, 12)
#define SB_P1_DIVIDER_SHIFT 12
#define PSB_LANE0 0x120
#define PSB_LANE1 0x220
#define PSB_LANE2 0x2320
#define PSB_LANE3 0x2420
#define LANE_PLL_MASK (0x7 << 20)
#define LANE_PLL_ENABLE (0x3 << 20)
#define LANE_PLL_PIPE(p) (((p) == 0) ? (1 << 21) : (0 << 21))
#define DP_B 0x64100
#define DP_C 0x64200
#define DP_PORT_EN (1 << 31)
#define DP_PIPEB_SELECT (1 << 30)
#define DP_PIPE_MASK (1 << 30)
/* Link training mode - select a suitable mode for each stage */
#define DP_LINK_TRAIN_PAT_1 (0 << 28)
#define DP_LINK_TRAIN_PAT_2 (1 << 28)
#define DP_LINK_TRAIN_PAT_IDLE (2 << 28)
#define DP_LINK_TRAIN_OFF (3 << 28)
#define DP_LINK_TRAIN_MASK (3 << 28)
#define DP_LINK_TRAIN_SHIFT 28
/* Signal voltages. These are mostly controlled by the other end */
#define DP_VOLTAGE_0_4 (0 << 25)
#define DP_VOLTAGE_0_6 (1 << 25)
#define DP_VOLTAGE_0_8 (2 << 25)
#define DP_VOLTAGE_1_2 (3 << 25)
#define DP_VOLTAGE_MASK (7 << 25)
#define DP_VOLTAGE_SHIFT 25
/* Signal pre-emphasis levels, like voltages, the other end tells us what
* they want
*/
#define DP_PRE_EMPHASIS_0 (0 << 22)
#define DP_PRE_EMPHASIS_3_5 (1 << 22)
#define DP_PRE_EMPHASIS_6 (2 << 22)
#define DP_PRE_EMPHASIS_9_5 (3 << 22)
#define DP_PRE_EMPHASIS_MASK (7 << 22)
#define DP_PRE_EMPHASIS_SHIFT 22
/* How many wires to use. I guess 3 was too hard */
#define DP_PORT_WIDTH_1 (0 << 19)
#define DP_PORT_WIDTH_2 (1 << 19)
#define DP_PORT_WIDTH_4 (3 << 19)
#define DP_PORT_WIDTH_MASK (7 << 19)
/* Mystic DPCD version 1.1 special mode */
#define DP_ENHANCED_FRAMING (1 << 18)
/** locked once port is enabled */
#define DP_PORT_REVERSAL (1 << 15)
/** sends the clock on lane 15 of the PEG for debug */
#define DP_CLOCK_OUTPUT_ENABLE (1 << 13)
#define DP_SCRAMBLING_DISABLE (1 << 12)
#define DP_SCRAMBLING_DISABLE_IRONLAKE (1 << 7)
/** limit RGB values to avoid confusing TVs */
#define DP_COLOR_RANGE_16_235 (1 << 8)
/** Turn on the audio link */
#define DP_AUDIO_OUTPUT_ENABLE (1 << 6)
/** vs and hs sync polarity */
#define DP_SYNC_VS_HIGH (1 << 4)
#define DP_SYNC_HS_HIGH (1 << 3)
/** A fantasy */
#define DP_DETECTED (1 << 2)
/** The aux channel provides a way to talk to the
* signal sink for DDC etc. Max packet size supported
* is 20 bytes in each direction, hence the 5 fixed
* data registers
*/
#define DPB_AUX_CH_CTL 0x64110
#define DPB_AUX_CH_DATA1 0x64114
#define DPB_AUX_CH_DATA2 0x64118
#define DPB_AUX_CH_DATA3 0x6411c
#define DPB_AUX_CH_DATA4 0x64120
#define DPB_AUX_CH_DATA5 0x64124
#define DPC_AUX_CH_CTL 0x64210
#define DPC_AUX_CH_DATA1 0x64214
#define DPC_AUX_CH_DATA2 0x64218
#define DPC_AUX_CH_DATA3 0x6421c
#define DPC_AUX_CH_DATA4 0x64220
#define DPC_AUX_CH_DATA5 0x64224
#define DP_AUX_CH_CTL_SEND_BUSY (1 << 31)
#define DP_AUX_CH_CTL_DONE (1 << 30)
#define DP_AUX_CH_CTL_INTERRUPT (1 << 29)
#define DP_AUX_CH_CTL_TIME_OUT_ERROR (1 << 28)
#define DP_AUX_CH_CTL_TIME_OUT_400us (0 << 26)
#define DP_AUX_CH_CTL_TIME_OUT_600us (1 << 26)
#define DP_AUX_CH_CTL_TIME_OUT_800us (2 << 26)
#define DP_AUX_CH_CTL_TIME_OUT_1600us (3 << 26)
#define DP_AUX_CH_CTL_TIME_OUT_MASK (3 << 26)
#define DP_AUX_CH_CTL_RECEIVE_ERROR (1 << 25)
#define DP_AUX_CH_CTL_MESSAGE_SIZE_MASK (0x1f << 20)
#define DP_AUX_CH_CTL_MESSAGE_SIZE_SHIFT 20
#define DP_AUX_CH_CTL_PRECHARGE_2US_MASK (0xf << 16)
#define DP_AUX_CH_CTL_PRECHARGE_2US_SHIFT 16
#define DP_AUX_CH_CTL_AUX_AKSV_SELECT (1 << 15)
#define DP_AUX_CH_CTL_MANCHESTER_TEST (1 << 14)
#define DP_AUX_CH_CTL_SYNC_TEST (1 << 13)
#define DP_AUX_CH_CTL_DEGLITCH_TEST (1 << 12)
#define DP_AUX_CH_CTL_PRECHARGE_TEST (1 << 11)
#define DP_AUX_CH_CTL_BIT_CLOCK_2X_MASK (0x7ff)
#define DP_AUX_CH_CTL_BIT_CLOCK_2X_SHIFT 0
/*
* Computing GMCH M and N values for the Display Port link
*
* GMCH M/N = dot clock * bytes per pixel / ls_clk * # of lanes
*
* ls_clk (we assume) is the DP link clock (1.62 or 2.7 GHz)
*
* The GMCH value is used internally
*
* bytes_per_pixel is the number of bytes coming out of the plane,
* which is after the LUTs, so we want the bytes for our color format.
* For our current usage, this is always 3, one byte for R, G and B.
*/
#define _PIPEA_GMCH_DATA_M 0x70050
#define _PIPEB_GMCH_DATA_M 0x71050
/* Transfer unit size for display port - 1, default is 0x3f (for TU size 64) */
#define PIPE_GMCH_DATA_M_TU_SIZE_MASK (0x3f << 25)
#define PIPE_GMCH_DATA_M_TU_SIZE_SHIFT 25
#define PIPE_GMCH_DATA_M_MASK (0xffffff)
#define _PIPEA_GMCH_DATA_N 0x70054
#define _PIPEB_GMCH_DATA_N 0x71054
#define PIPE_GMCH_DATA_N_MASK (0xffffff)
/*
* Computing Link M and N values for the Display Port link
*
* Link M / N = pixel_clock / ls_clk
*
* (the DP spec calls pixel_clock the 'strm_clk')
*
* The Link value is transmitted in the Main Stream
* Attributes and VB-ID.
*/
#define _PIPEA_DP_LINK_M 0x70060
#define _PIPEB_DP_LINK_M 0x71060
#define PIPEA_DP_LINK_M_MASK (0xffffff)
#define _PIPEA_DP_LINK_N 0x70064
#define _PIPEB_DP_LINK_N 0x71064
#define PIPEA_DP_LINK_N_MASK (0xffffff)
#define PIPE_GMCH_DATA_M(pipe) _PIPE(pipe, _PIPEA_GMCH_DATA_M, _PIPEB_GMCH_DATA_M)
#define PIPE_GMCH_DATA_N(pipe) _PIPE(pipe, _PIPEA_GMCH_DATA_N, _PIPEB_GMCH_DATA_N)
#define PIPE_DP_LINK_M(pipe) _PIPE(pipe, _PIPEA_DP_LINK_M, _PIPEB_DP_LINK_M)
#define PIPE_DP_LINK_N(pipe) _PIPE(pipe, _PIPEA_DP_LINK_N, _PIPEB_DP_LINK_N)
#define PIPE_BPC_MASK (7 << 5)
#define PIPE_8BPC (0 << 5)
#define PIPE_10BPC (1 << 5)
#define PIPE_6BPC (2 << 5)
#endif
Reference in New Issue View Git Blame Copy Permalink