linux/Documentation/devicetree/bindings/usb/msm-hsusb.txt

111 lines
4.2 KiB
Plaintext

MSM SoC HSUSB controllers
EHCI
Required properties:
- compatible: Should contain "qcom,ehci-host"
- regs: offset and length of the register set in the memory map
- usb-phy: phandle for the PHY device
Example EHCI controller device node:
ehci: ehci@f9a55000 {
compatible = "qcom,ehci-host";
reg = <0xf9a55000 0x400>;
usb-phy = <&usb_otg>;
};
USB PHY with optional OTG:
Required properties:
- compatible: Should contain:
"qcom,usb-otg-ci" for chipsets with ChipIdea 45nm PHY
"qcom,usb-otg-snps" for chipsets with Synopsys 28nm PHY
- regs: Offset and length of the register set in the memory map
- interrupts: interrupt-specifier for the OTG interrupt.
- clocks: A list of phandle + clock-specifier pairs for the
clocks listed in clock-names
- clock-names: Should contain the following:
"phy" USB PHY reference clock
"core" Protocol engine clock
"iface" Interface bus clock
"alt_core" Protocol engine clock for targets with asynchronous
reset methodology. (optional)
- vdccx-supply: phandle to the regulator for the vdd supply for
digital circuit operation.
- v1p8-supply: phandle to the regulator for the 1.8V supply
- v3p3-supply: phandle to the regulator for the 3.3V supply
- resets: A list of phandle + reset-specifier pairs for the
resets listed in reset-names
- reset-names: Should contain the following:
"phy" USB PHY controller reset
"link" USB LINK controller reset
- qcom,otg-control: OTG control (VBUS and ID notifications) can be one of
1 - PHY control
2 - PMIC control
Optional properties:
- dr_mode: One of "host", "peripheral" or "otg". Defaults to "otg"
- switch-gpio: A phandle + gpio-specifier pair. Some boards are using Dual
SPDT USB Switch, witch is cotrolled by GPIO to de/multiplex
D+/D- USB lines between connectors.
- qcom,phy-init-sequence: PHY configuration sequence values. This is related to Device
Mode Eye Diagram test. Start address at which these values will be
written is ULPI_EXT_VENDOR_SPECIFIC. Value of -1 is reserved as
"do not overwrite default value at this address".
For example: qcom,phy-init-sequence = < -1 0x63 >;
Will update only value at address ULPI_EXT_VENDOR_SPECIFIC + 1.
- qcom,phy-num: Select number of pyco-phy to use, can be one of
0 - PHY one, default
1 - Second PHY
Some platforms may have configuration to allow USB
controller work with any of the two HSPHYs present.
- qcom,vdd-levels: This property must be a list of three integer values
(no, min, max) where each value represents either a voltage
in microvolts or a value corresponding to voltage corner.
- qcom,manual-pullup: If present, vbus is not routed to USB controller/phy
and controller driver therefore enables pull-up explicitly
before starting controller using usbcmd run/stop bit.
- extcon: phandles to external connector devices. First phandle
should point to external connector, which provide "USB"
cable events, the second should point to external connector
device, which provide "USB-HOST" cable events. If one of
the external connector devices is not required empty <0>
phandle should be specified.
Example HSUSB OTG controller device node:
usb@f9a55000 {
compatible = "qcom,usb-otg-snps";
reg = <0xf9a55000 0x400>;
interrupts = <0 134 0>;
dr_mode = "peripheral";
clocks = <&gcc GCC_XO_CLK>, <&gcc GCC_USB_HS_SYSTEM_CLK>,
<&gcc GCC_USB_HS_AHB_CLK>;
clock-names = "phy", "core", "iface";
vddcx-supply = <&pm8841_s2_corner>;
v1p8-supply = <&pm8941_l6>;
v3p3-supply = <&pm8941_l24>;
resets = <&gcc GCC_USB2A_PHY_BCR>, <&gcc GCC_USB_HS_BCR>;
reset-names = "phy", "link";
qcom,otg-control = <1>;
qcom,phy-init-sequence = < -1 0x63 >;
qcom,vdd-levels = <1 5 7>;
};