1afb89746c
UART3 is used by expansion boards to get a tty console. Thus, the pinmux should be defined by expansion boards, instead of being imposed by the processor board. Signed-off-by: Florian Vaussard <florian.vaussard@epfl.ch> Signed-off-by: Tony Lindgren <tony@atomide.com>
222 lines
6.3 KiB
Plaintext
222 lines
6.3 KiB
Plaintext
/*
|
|
* Copyright (C) 2012 Florian Vaussard, EPFL Mobots group
|
|
*
|
|
* This program is free software; you can redistribute it and/or modify
|
|
* it under the terms of the GNU General Public License version 2 as
|
|
* published by the Free Software Foundation.
|
|
*/
|
|
|
|
/*
|
|
* The Gumstix Overo must be combined with an expansion board.
|
|
*/
|
|
|
|
/ {
|
|
pwmleds {
|
|
compatible = "pwm-leds";
|
|
|
|
overo {
|
|
label = "overo:blue:COM";
|
|
pwms = <&twl_pwmled 1 7812500>;
|
|
max-brightness = <127>;
|
|
linux,default-trigger = "mmc0";
|
|
};
|
|
};
|
|
|
|
sound {
|
|
compatible = "ti,omap-twl4030";
|
|
ti,model = "overo";
|
|
|
|
ti,mcbsp = <&mcbsp2>;
|
|
ti,codec = <&twl_audio>;
|
|
};
|
|
|
|
/* HS USB Port 2 Power */
|
|
hsusb2_power: hsusb2_power_reg {
|
|
compatible = "regulator-fixed";
|
|
regulator-name = "hsusb2_vbus";
|
|
regulator-min-microvolt = <5000000>;
|
|
regulator-max-microvolt = <5000000>;
|
|
gpio = <&gpio6 8 0>; /* gpio_168: vbus enable */
|
|
startup-delay-us = <70000>;
|
|
enable-active-high;
|
|
};
|
|
|
|
/* HS USB Host PHY on PORT 2 */
|
|
hsusb2_phy: hsusb2_phy {
|
|
compatible = "usb-nop-xceiv";
|
|
reset-gpios = <&gpio6 23 GPIO_ACTIVE_LOW>; /* gpio_183 */
|
|
vcc-supply = <&hsusb2_power>;
|
|
};
|
|
|
|
/* Regulator to trigger the nPoweron signal of the Wifi module */
|
|
w3cbw003c_npoweron: regulator-w3cbw003c-npoweron {
|
|
compatible = "regulator-fixed";
|
|
regulator-name = "regulator-w3cbw003c-npoweron";
|
|
regulator-min-microvolt = <3300000>;
|
|
regulator-max-microvolt = <3300000>;
|
|
gpio = <&gpio2 22 GPIO_ACTIVE_HIGH>; /* gpio_54: nPoweron */
|
|
enable-active-high;
|
|
};
|
|
|
|
/* Regulator to trigger the nReset signal of the Wifi module */
|
|
w3cbw003c_wifi_nreset: regulator-w3cbw003c-wifi-nreset {
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&w3cbw003c_pins &w3cbw003c_2_pins>;
|
|
compatible = "regulator-fixed";
|
|
regulator-name = "regulator-w3cbw003c-wifi-nreset";
|
|
regulator-min-microvolt = <3300000>;
|
|
regulator-max-microvolt = <3300000>;
|
|
gpio = <&gpio1 16 GPIO_ACTIVE_HIGH>; /* gpio_16: WiFi nReset */
|
|
startup-delay-us = <10000>;
|
|
};
|
|
|
|
/* Regulator to trigger the nReset signal of the Bluetooth module */
|
|
w3cbw003c_bt_nreset: regulator-w3cbw003c-bt-nreset {
|
|
compatible = "regulator-fixed";
|
|
regulator-name = "regulator-w3cbw003c-bt-nreset";
|
|
regulator-min-microvolt = <3300000>;
|
|
regulator-max-microvolt = <3300000>;
|
|
gpio = <&gpio6 4 GPIO_ACTIVE_HIGH>; /* gpio_164: BT nReset */
|
|
startup-delay-us = <10000>;
|
|
};
|
|
};
|
|
|
|
&omap3_pmx_core {
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <
|
|
&hsusb2_pins
|
|
>;
|
|
|
|
uart2_pins: pinmux_uart2_pins {
|
|
pinctrl-single,pins = <
|
|
OMAP3_CORE1_IOPAD(0x216c, PIN_INPUT | MUX_MODE1) /* mcbsp3_dx.uart2_cts */
|
|
OMAP3_CORE1_IOPAD(0x216e, PIN_OUTPUT | MUX_MODE1) /* mcbsp3_dr.uart2_rts */
|
|
OMAP3_CORE1_IOPAD(0x2170, PIN_OUTPUT | MUX_MODE1) /* mcbsp3_clk.uart2_tx */
|
|
OMAP3_CORE1_IOPAD(0x2172, PIN_INPUT | MUX_MODE1) /* mcbsp3_fsx.uart2_rx */
|
|
>;
|
|
};
|
|
|
|
i2c1_pins: pinmux_i2c1_pins {
|
|
pinctrl-single,pins = <
|
|
OMAP3_CORE1_IOPAD(0x21ba, PIN_INPUT | MUX_MODE0) /* i2c1_scl.i2c1_scl */
|
|
OMAP3_CORE1_IOPAD(0x21bc, PIN_INPUT | MUX_MODE0) /* i2c1_sda.i2c1_sda */
|
|
>;
|
|
};
|
|
|
|
mmc1_pins: pinmux_mmc1_pins {
|
|
pinctrl-single,pins = <
|
|
OMAP3_CORE1_IOPAD(0x2144, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_clk.sdmmc1_clk */
|
|
OMAP3_CORE1_IOPAD(0x2146, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_cmd.sdmmc1_cmd */
|
|
OMAP3_CORE1_IOPAD(0x2148, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat0.sdmmc1_dat0 */
|
|
OMAP3_CORE1_IOPAD(0x214a, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat1.sdmmc1_dat1 */
|
|
OMAP3_CORE1_IOPAD(0x214c, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat2.sdmmc1_dat2 */
|
|
OMAP3_CORE1_IOPAD(0x214e, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat3.sdmmc1_dat3 */
|
|
>;
|
|
};
|
|
|
|
mmc2_pins: pinmux_mmc2_pins {
|
|
pinctrl-single,pins = <
|
|
OMAP3_CORE1_IOPAD(0x2158, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_clk.sdmmc2_clk */
|
|
OMAP3_CORE1_IOPAD(0x215a, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_cmd.sdmmc2_cmd */
|
|
OMAP3_CORE1_IOPAD(0x215c, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat0.sdmmc2_dat0 */
|
|
OMAP3_CORE1_IOPAD(0x215e, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat1.sdmmc2_dat1 */
|
|
OMAP3_CORE1_IOPAD(0x2160, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat2.sdmmc2_dat2 */
|
|
OMAP3_CORE1_IOPAD(0x2162, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat3.sdmmc2_dat3 */
|
|
>;
|
|
};
|
|
|
|
/* WiFi/BT combo */
|
|
w3cbw003c_pins: pinmux_w3cbw003c_pins {
|
|
pinctrl-single,pins = <
|
|
OMAP3_CORE1_IOPAD(0x20b4, PIN_OUTPUT | MUX_MODE4) /* gpmc_ncs3.gpio_54 */
|
|
OMAP3_CORE1_IOPAD(0x219c, PIN_OUTPUT | MUX_MODE4) /* uart3_rts_sd.gpio_164 */
|
|
>;
|
|
};
|
|
|
|
hsusb2_pins: pinmux_hsusb2_pins {
|
|
pinctrl-single,pins = <
|
|
OMAP3_CORE1_IOPAD(0x21d4, PIN_INPUT_PULLDOWN | MUX_MODE3) /* mcspi1_cs3.hsusb2_data2 */
|
|
OMAP3_CORE1_IOPAD(0x21d6, PIN_INPUT_PULLDOWN | MUX_MODE3) /* mcspi2_clk.hsusb2_data7 */
|
|
OMAP3_CORE1_IOPAD(0x21d8, PIN_INPUT_PULLDOWN | MUX_MODE3) /* mcspi2_simo.hsusb2_data4 */
|
|
OMAP3_CORE1_IOPAD(0x21da, PIN_INPUT_PULLDOWN | MUX_MODE3) /* mcspi2_somi.hsusb2_data5 */
|
|
OMAP3_CORE1_IOPAD(0x21dc, PIN_INPUT_PULLDOWN | MUX_MODE3) /* mcspi2_cs0.hsusb2_data6 */
|
|
OMAP3_CORE1_IOPAD(0x21de, PIN_INPUT_PULLDOWN | MUX_MODE3) /* mcspi2_cs1.hsusb2_data3 */
|
|
OMAP3_CORE1_IOPAD(0x21be, PIN_OUTPUT | MUX_MODE4) /* i2c2_scl.gpio_168 */
|
|
OMAP3_CORE1_IOPAD(0x21c0, PIN_OUTPUT | MUX_MODE4) /* i2c2_sda.gpio_183 */
|
|
>;
|
|
};
|
|
};
|
|
|
|
&i2c1 {
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&i2c1_pins>;
|
|
clock-frequency = <2600000>;
|
|
|
|
twl: twl@48 {
|
|
reg = <0x48>;
|
|
interrupts = <7>; /* SYS_NIRQ cascaded to intc */
|
|
interrupt-parent = <&intc>;
|
|
|
|
twl_audio: audio {
|
|
compatible = "ti,twl4030-audio";
|
|
codec {
|
|
};
|
|
};
|
|
};
|
|
};
|
|
|
|
#include "twl4030.dtsi"
|
|
#include "twl4030_omap3.dtsi"
|
|
|
|
/* i2c2 pins are used for gpio */
|
|
&i2c2 {
|
|
status = "disabled";
|
|
};
|
|
|
|
/* on board microSD slot */
|
|
&mmc1 {
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&mmc1_pins>;
|
|
vmmc-supply = <&vmmc1>;
|
|
bus-width = <4>;
|
|
};
|
|
|
|
/* optional on board WiFi */
|
|
&mmc2 {
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&mmc2_pins>;
|
|
vmmc-supply = <&w3cbw003c_npoweron>;
|
|
vqmmc-supply = <&w3cbw003c_bt_nreset>;
|
|
vmmc_aux-supply = <&w3cbw003c_wifi_nreset>;
|
|
bus-width = <4>;
|
|
cap-sdio-irq;
|
|
non-removable;
|
|
};
|
|
|
|
&twl_gpio {
|
|
ti,use-leds;
|
|
};
|
|
|
|
&usb_otg_hs {
|
|
interface-type = <0>;
|
|
usb-phy = <&usb2_phy>;
|
|
phys = <&usb2_phy>;
|
|
phy-names = "usb2-phy";
|
|
mode = <3>;
|
|
power = <50>;
|
|
};
|
|
|
|
&usbhshost {
|
|
port2-mode = "ehci-phy";
|
|
};
|
|
|
|
&usbhsehci {
|
|
phys = <0 &hsusb2_phy>;
|
|
};
|
|
|
|
&uart2 {
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&uart2_pins>;
|
|
};
|
|
|