ad238495fe
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com> Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
34 lines
1.5 KiB
C
34 lines
1.5 KiB
C
/* Buttons */
|
|
#define GPIO_TRIG_NET_IN AT91_PIN_PB21
|
|
#define GPIO_CARD_UNMOUNT_0 AT91_PIN_PB13
|
|
#define GPIO_CARD_UNMOUNT_1 AT91_PIN_PB12
|
|
#define GPIO_KEY_POWER AT91_PIN_PA25
|
|
|
|
/* PCF8574 0x20 GPIO - U1 on the GS_IA18-CB_V3 board */
|
|
#define GS_IA18_S_PCF_GPIO_BASE0 NR_BUILTIN_GPIO
|
|
#define PCF_GPIO_HDC_POWER (GS_IA18_S_PCF_GPIO_BASE0 + 0)
|
|
#define PCF_GPIO_WIFI_SETUP (GS_IA18_S_PCF_GPIO_BASE0 + 1)
|
|
#define PCF_GPIO_WIFI_ENABLE (GS_IA18_S_PCF_GPIO_BASE0 + 2)
|
|
#define PCF_GPIO_WIFI_RESET (GS_IA18_S_PCF_GPIO_BASE0 + 3)
|
|
#define PCF_GPIO_ETH_DETECT 4 /* this is a GPI */
|
|
#define PCF_GPIO_GPS_SETUP (GS_IA18_S_PCF_GPIO_BASE0 + 5)
|
|
#define PCF_GPIO_GPS_STANDBY (GS_IA18_S_PCF_GPIO_BASE0 + 6)
|
|
#define PCF_GPIO_GPS_POWER (GS_IA18_S_PCF_GPIO_BASE0 + 7)
|
|
|
|
/* PCF8574 0x22 GPIO - U1 on the GS_2G_OPT1-A_V0 board (Alarm) */
|
|
#define GS_IA18_S_PCF_GPIO_BASE1 (GS_IA18_S_PCF_GPIO_BASE0 + 8)
|
|
#define PCF_GPIO_ALARM1 (GS_IA18_S_PCF_GPIO_BASE1 + 0)
|
|
#define PCF_GPIO_ALARM2 (GS_IA18_S_PCF_GPIO_BASE1 + 1)
|
|
#define PCF_GPIO_ALARM3 (GS_IA18_S_PCF_GPIO_BASE1 + 2)
|
|
#define PCF_GPIO_ALARM4 (GS_IA18_S_PCF_GPIO_BASE1 + 3)
|
|
/* bits 4, 5, 6 not used */
|
|
#define PCF_GPIO_ALARM_V_RELAY_ON (GS_IA18_S_PCF_GPIO_BASE1 + 7)
|
|
|
|
/* PCF8574 0x24 GPIO U1 on the GS_2G-OPT23-A_V0 board (Modem) */
|
|
#define GS_IA18_S_PCF_GPIO_BASE2 (GS_IA18_S_PCF_GPIO_BASE1 + 8)
|
|
#define PCF_GPIO_MODEM_POWER (GS_IA18_S_PCF_GPIO_BASE2 + 0)
|
|
#define PCF_GPIO_MODEM_RESET (GS_IA18_S_PCF_GPIO_BASE2 + 3)
|
|
/* bits 1, 2, 4, 5 not used */
|
|
#define PCF_GPIO_TRX_RESET (GS_IA18_S_PCF_GPIO_BASE2 + 6)
|
|
/* bit 7 not used */
|