OpenE2K/linux
6
0
Fork 0
Code Issues Pull Requests Releases Wiki Activity
73d1a2c467
linux/drivers/usb/gadget/Kconfig
Robert Jarzmik d75379a538 usb: pxa27x_udc driver 
Adds pxa27x udc driver to support USB peripherals on pxa27x chips.

The driver is compatible with: Gadget Zero, the File Storage
gadget, and the Ethernet gadget (only in CDC subset mode).

The driver can't properly support multiple interfaces, because
of hardware bugs without possible workaround.  That means no
RNDIS support from g_ether, and no CDC ACM support in g_serial.

Signed-off-by: Robert Jarzmik <rjarzmik@free.fr>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2008-05-02 10:25:53 -07:00

597 lines
20 KiB
Plaintext
Raw Blame History

#
# USB Gadget support on a system involves
# (a) a peripheral controller, and
# (b) the gadget driver using it.
#
# NOTE: Gadget support ** DOES NOT ** depend on host-side CONFIG_USB !!
#
# - Host systems (like PCs) need CONFIG_USB (with "A" jacks).
# - Peripherals (like PDAs) need CONFIG_USB_GADGET (with "B" jacks).
# - Some systems have both kinds of controllers.
#
# With help from a special transceiver and a "Mini-AB" jack, systems with
# both kinds of controller can also support "USB On-the-Go" (CONFIG_USB_OTG).
#
menuconfig USB_GADGET
tristate "USB Gadget Support"
help
USB is a master/slave protocol, organized with one master
host (such as a PC) controlling up to 127 peripheral devices.
The USB hardware is asymmetric, which makes it easier to set up:
you can't connect a "to-the-host" connector to a peripheral.
Linux can run in the host, or in the peripheral. In both cases
you need a low level bus controller driver, and some software
talking to it. Peripheral controllers are often discrete silicon,
or are integrated with the CPU in a microcontroller. The more
familiar host side controllers have names like "EHCI", "OHCI",
or "UHCI", and are usually integrated into southbridges on PC
motherboards.
Enable this configuration option if you want to run Linux inside
a USB peripheral device. Configure one hardware driver for your
peripheral/device side bus controller, and a "gadget driver" for
your peripheral protocol. (If you use modular gadget drivers,
you may configure more than one.)
If in doubt, say "N" and don't enable these drivers; most people
don't have this kind of hardware (except maybe inside Linux PDAs).
For more information, see <http://www.linux-usb.org/gadget> and
the kernel DocBook documentation for this API.
if USB_GADGET
config USB_GADGET_DEBUG
boolean "Debugging messages (DEVELOPMENT)"
depends on USB_GADGET && DEBUG_KERNEL
help
Many controller and gadget drivers will print some debugging
messages if you use this option to ask for those messages.
Avoid enabling these messages, even if you're actively
debugging such a driver. Many drivers will emit so many
messages that the driver timings are affected, which will
either create new failure modes or remove the one you're
trying to track down. Never enable these messages for a
production build.
config USB_GADGET_DEBUG_FILES
boolean "Debugging information files (DEVELOPMENT)"
depends on USB_GADGET && PROC_FS
help
Some of the drivers in the "gadget" framework can expose
debugging information in files such as /proc/driver/udc
(for a peripheral controller). The information in these
files may help when you're troubleshooting or bringing up a
driver on a new board. Enable these files by choosing "Y"
here. If in doubt, or to conserve kernel memory, say "N".
config USB_GADGET_DEBUG_FS
boolean "Debugging information files in debugfs (DEVELOPMENT)"
depends on USB_GADGET && DEBUG_FS
help
Some of the drivers in the "gadget" framework can expose
debugging information in files under /sys/kernel/debug/.
The information in these files may help when you're
troubleshooting or bringing up a driver on a new board.
Enable these files by choosing "Y" here. If in doubt, or
to conserve kernel memory, say "N".
config USB_GADGET_SELECTED
boolean
#
# USB Peripheral Controller Support
#
choice
prompt "USB Peripheral Controller"
depends on USB_GADGET
help
A USB device uses a controller to talk to its host.
Systems should have only one such upstream link.
Many controller drivers are platform-specific; these
often need board-specific hooks.
config USB_GADGET_AMD5536UDC
boolean "AMD5536 UDC"
depends on PCI
select USB_GADGET_DUALSPEED
help
The AMD5536 UDC is part of the AMD Geode CS5536, an x86 southbridge.
It is a USB Highspeed DMA capable USB device controller. Beside ep0
it provides 4 IN and 4 OUT endpoints (bulk or interrupt type).
The UDC port supports OTG operation, and may be used as a host port
if it's not being used to implement peripheral or OTG roles.
Say "y" to link the driver statically, or "m" to build a
dynamically linked module called "amd5536udc" and force all
gadget drivers to also be dynamically linked.
config USB_AMD5536UDC
tristate
depends on USB_GADGET_AMD5536UDC
default USB_GADGET
select USB_GADGET_SELECTED
config USB_GADGET_ATMEL_USBA
boolean "Atmel USBA"
select USB_GADGET_DUALSPEED
depends on AVR32 || ARCH_AT91CAP9
help
USBA is the integrated high-speed USB Device controller on
the AT32AP700x and AT91CAP9 processors from Atmel.
config USB_ATMEL_USBA
tristate
depends on USB_GADGET_ATMEL_USBA
default USB_GADGET
select USB_GADGET_SELECTED
config USB_GADGET_FSL_USB2
boolean "Freescale Highspeed USB DR Peripheral Controller"
depends on FSL_SOC
select USB_GADGET_DUALSPEED
help
Some of Freescale PowerPC processors have a High Speed
Dual-Role(DR) USB controller, which supports device mode.
The number of programmable endpoints is different through
SOC revisions.
Say "y" to link the driver statically, or "m" to build a
dynamically linked module called "fsl_usb2_udc" and force
all gadget drivers to also be dynamically linked.
config USB_FSL_USB2
tristate
depends on USB_GADGET_FSL_USB2
default USB_GADGET
select USB_GADGET_SELECTED
config USB_GADGET_NET2280
boolean "NetChip 228x"
depends on PCI
select USB_GADGET_DUALSPEED
help
NetChip 2280 / 2282 is a PCI based USB peripheral controller which
supports both full and high speed USB 2.0 data transfers.
It has six configurable endpoints, as well as endpoint zero
(for control transfers) and several endpoints with dedicated
functions.
Say "y" to link the driver statically, or "m" to build a
dynamically linked module called "net2280" and force all
gadget drivers to also be dynamically linked.
config USB_NET2280
tristate
depends on USB_GADGET_NET2280
default USB_GADGET
select USB_GADGET_SELECTED
config USB_GADGET_PXA2XX
boolean "PXA 25x or IXP 4xx"
depends on (ARCH_PXA && PXA25x) || ARCH_IXP4XX
help
Intel's PXA 25x series XScale ARM-5TE processors include
an integrated full speed USB 1.1 device controller. The
controller in the IXP 4xx series is register-compatible.
It has fifteen fixed-function endpoints, as well as endpoint
zero (for control transfers).
Say "y" to link the driver statically, or "m" to build a
dynamically linked module called "pxa2xx_udc" and force all
gadget drivers to also be dynamically linked.
config USB_PXA2XX
tristate
depends on USB_GADGET_PXA2XX
default USB_GADGET
select USB_GADGET_SELECTED
# if there's only one gadget driver, using only two bulk endpoints,
# don't waste memory for the other endpoints
config USB_PXA2XX_SMALL
depends on USB_GADGET_PXA2XX
bool
default n if USB_ETH_RNDIS
default y if USB_ZERO
default y if USB_ETH
default y if USB_G_SERIAL
config USB_GADGET_M66592
boolean "Renesas M66592 USB Peripheral Controller"
select USB_GADGET_DUALSPEED
help
M66592 is a discrete USB peripheral controller chip that
supports both full and high speed USB 2.0 data transfers.
It has seven configurable endpoints, and endpoint zero.
Say "y" to link the driver statically, or "m" to build a
dynamically linked module called "m66592_udc" and force all
gadget drivers to also be dynamically linked.
config USB_M66592
tristate
depends on USB_GADGET_M66592
default USB_GADGET
select USB_GADGET_SELECTED
config SUPERH_BUILT_IN_M66592
boolean "Enable SuperH built-in USB like the M66592"
depends on USB_GADGET_M66592 && CPU_SUBTYPE_SH7722
help
SH7722 has USB like the M66592.
The transfer rate is very slow when use "Ethernet Gadget".
However, this problem is improved if change a value of
NET_IP_ALIGN to 4.
config USB_GADGET_PXA27X
boolean "PXA 27x"
depends on ARCH_PXA && PXA27x
help
Intel's PXA 27x series XScale ARM v5TE processors include
an integrated full speed USB 1.1 device controller.
It has up to 23 endpoints, as well as endpoint zero (for
control transfers).
Say "y" to link the driver statically, or "m" to build a
dynamically linked module called "pxa27x_udc" and force all
gadget drivers to also be dynamically linked.
config USB_PXA27X
tristate
depends on USB_GADGET_PXA27X
default USB_GADGET
select USB_GADGET_SELECTED
config USB_GADGET_GOKU
boolean "Toshiba TC86C001 'Goku-S'"
depends on PCI
help
The Toshiba TC86C001 is a PCI device which includes controllers
for full speed USB devices, IDE, I2C, SIO, plus a USB host (OHCI).
The device controller has three configurable (bulk or interrupt)
endpoints, plus endpoint zero (for control transfers).
Say "y" to link the driver statically, or "m" to build a
dynamically linked module called "goku_udc" and to force all
gadget drivers to also be dynamically linked.
config USB_GOKU
tristate
depends on USB_GADGET_GOKU
default USB_GADGET
select USB_GADGET_SELECTED
config USB_GADGET_LH7A40X
boolean "LH7A40X"
depends on ARCH_LH7A40X
help
This driver provides USB Device Controller driver for LH7A40x
config USB_LH7A40X
tristate
depends on USB_GADGET_LH7A40X
default USB_GADGET
select USB_GADGET_SELECTED
config USB_GADGET_OMAP
boolean "OMAP USB Device Controller"
depends on ARCH_OMAP
select ISP1301_OMAP if MACH_OMAP_H2 || MACH_OMAP_H3
help
Many Texas Instruments OMAP processors have flexible full
speed USB device controllers, with support for up to 30
endpoints (plus endpoint zero). This driver supports the
controller in the OMAP 1611, and should work with controllers
in other OMAP processors too, given minor tweaks.
Say "y" to link the driver statically, or "m" to build a
dynamically linked module called "omap_udc" and force all
gadget drivers to also be dynamically linked.
config USB_OMAP
tristate
depends on USB_GADGET_OMAP
default USB_GADGET
select USB_GADGET_SELECTED
config USB_OTG
boolean "OTG Support"
depends on USB_GADGET_OMAP && ARCH_OMAP_OTG && USB_OHCI_HCD
help
The most notable feature of USB OTG is support for a
"Dual-Role" device, which can act as either a device
or a host. The initial role choice can be changed
later, when two dual-role devices talk to each other.
Select this only if your OMAP board has a Mini-AB connector.
config USB_GADGET_S3C2410
boolean "S3C2410 USB Device Controller"
depends on ARCH_S3C2410
help
Samsung's S3C2410 is an ARM-4 processor with an integrated
full speed USB 1.1 device controller. It has 4 configurable
endpoints, as well as endpoint zero (for control transfers).
This driver has been tested on the S3C2410, S3C2412, and
S3C2440 processors.
config USB_S3C2410
tristate
depends on USB_GADGET_S3C2410
default USB_GADGET
select USB_GADGET_SELECTED
config USB_S3C2410_DEBUG
boolean "S3C2410 udc debug messages"
depends on USB_GADGET_S3C2410
config USB_GADGET_AT91
boolean "AT91 USB Device Port"
depends on ARCH_AT91 && !ARCH_AT91SAM9RL && !ARCH_AT91CAP9
select USB_GADGET_SELECTED
help
Many Atmel AT91 processors (such as the AT91RM2000) have a
full speed USB Device Port with support for five configurable
endpoints (plus endpoint zero).
Say "y" to link the driver statically, or "m" to build a
dynamically linked module called "at91_udc" and force all
gadget drivers to also be dynamically linked.
config USB_AT91
tristate
depends on USB_GADGET_AT91
default USB_GADGET
config USB_GADGET_DUMMY_HCD
boolean "Dummy HCD (DEVELOPMENT)"
depends on USB=y || (USB=m && USB_GADGET=m)
select USB_GADGET_DUALSPEED
help
This host controller driver emulates USB, looping all data transfer
requests back to a USB "gadget driver" in the same host. The host
side is the master; the gadget side is the slave. Gadget drivers
can be high, full, or low speed; and they have access to endpoints
like those from NET2280, PXA2xx, or SA1100 hardware.
This may help in some stages of creating a driver to embed in a
Linux device, since it lets you debug several parts of the gadget
driver without its hardware or drivers being involved.
Since such a gadget side driver needs to interoperate with a host
side Linux-USB device driver, this may help to debug both sides
of a USB protocol stack.
Say "y" to link the driver statically, or "m" to build a
dynamically linked module called "dummy_hcd" and force all
gadget drivers to also be dynamically linked.
config USB_DUMMY_HCD
tristate
depends on USB_GADGET_DUMMY_HCD
default USB_GADGET
select USB_GADGET_SELECTED
# NOTE: Please keep dummy_hcd LAST so that "real hardware" appears
# first and will be selected by default.
endchoice
config USB_GADGET_DUALSPEED
bool
depends on USB_GADGET
default n
help
Means that gadget drivers should include extra descriptors
and code to handle dual-speed controllers.
#
# USB Gadget Drivers
#
choice
tristate "USB Gadget Drivers"
depends on USB_GADGET && USB_GADGET_SELECTED
default USB_ETH
help
A Linux "Gadget Driver" talks to the USB Peripheral Controller
driver through the abstract "gadget" API. Some other operating
systems call these "client" drivers, of which "class drivers"
are a subset (implementing a USB device class specification).
A gadget driver implements one or more USB functions using
the peripheral hardware.
Gadget drivers are hardware-neutral, or "platform independent",
except that they sometimes must understand quirks or limitations
of the particular controllers they work with. For example, when
a controller doesn't support alternate configurations or provide
enough of the right types of endpoints, the gadget driver might
not be able work with that controller, or might need to implement
a less common variant of a device class protocol.
# this first set of drivers all depend on bulk-capable hardware.
config USB_ZERO
tristate "Gadget Zero (DEVELOPMENT)"
help
Gadget Zero is a two-configuration device. It either sinks and
sources bulk data; or it loops back a configurable number of
transfers. It also implements control requests, for "chapter 9"
conformance. The driver needs only two bulk-capable endpoints, so
it can work on top of most device-side usb controllers. It's
useful for testing, and is also a working example showing how
USB "gadget drivers" can be written.
Make this be the first driver you try using on top of any new
USB peripheral controller driver. Then you can use host-side
test software, like the "usbtest" driver, to put your hardware
and its driver through a basic set of functional tests.
Gadget Zero also works with the host-side "usb-skeleton" driver,
and with many kinds of host-side test software. You may need
to tweak product and vendor IDs before host software knows about
this device, and arrange to select an appropriate configuration.
Say "y" to link the driver statically, or "m" to build a
dynamically linked module called "g_zero".
config USB_ZERO_HNPTEST
boolean "HNP Test Device"
depends on USB_ZERO && USB_OTG
help
You can configure this device to enumerate using the device
identifiers of the USB-OTG test device. That means that when
this gadget connects to another OTG device, with this one using
the "B-Peripheral" role, that device will use HNP to let this
one serve as the USB host instead (in the "B-Host" role).
config USB_ETH
tristate "Ethernet Gadget (with CDC Ethernet support)"
depends on NET
help
This driver implements Ethernet style communication, in either
of two ways:
- The "Communication Device Class" (CDC) Ethernet Control Model.
That protocol is often avoided with pure Ethernet adapters, in
favor of simpler vendor-specific hardware, but is widely
supported by firmware for smart network devices.
- On hardware can't implement that protocol, a simple CDC subset
is used, placing fewer demands on USB.
RNDIS support is a third option, more demanding than that subset.
Within the USB device, this gadget driver exposes a network device
"usbX", where X depends on what other networking devices you have.
Treat it like a two-node Ethernet link: host, and gadget.
The Linux-USB host-side "usbnet" driver interoperates with this
driver, so that deep I/O queues can be supported. On 2.4 kernels,
use "CDCEther" instead, if you're using the CDC option. That CDC
mode should also interoperate with standard CDC Ethernet class
drivers on other host operating systems.
Say "y" to link the driver statically, or "m" to build a
dynamically linked module called "g_ether".
config USB_ETH_RNDIS
bool "RNDIS support"
depends on USB_ETH
default y
help
Microsoft Windows XP bundles the "Remote NDIS" (RNDIS) protocol,
and Microsoft provides redistributable binary RNDIS drivers for
older versions of Windows.
If you say "y" here, the Ethernet gadget driver will try to provide
a second device configuration, supporting RNDIS to talk to such
Microsoft USB hosts.
To make MS-Windows work with this, use Documentation/usb/linux.inf
as the "driver info file". For versions of MS-Windows older than
XP, you'll need to download drivers from Microsoft's website; a URL
is given in comments found in that info file.
config USB_GADGETFS
tristate "Gadget Filesystem (EXPERIMENTAL)"
depends on EXPERIMENTAL
help
This driver provides a filesystem based API that lets user mode
programs implement a single-configuration USB device, including
endpoint I/O and control requests that don't relate to enumeration.
All endpoints, transfer speeds, and transfer types supported by
the hardware are available, through read() and write() calls.
Currently, this option is still labelled as EXPERIMENTAL because
of existing race conditions in the underlying in-kernel AIO core.
Say "y" to link the driver statically, or "m" to build a
dynamically linked module called "gadgetfs".
config USB_FILE_STORAGE
tristate "File-backed Storage Gadget"
depends on BLOCK
help
The File-backed Storage Gadget acts as a USB Mass Storage
disk drive. As its storage repository it can use a regular
file or a block device (in much the same way as the "loop"
device driver), specified as a module parameter.
Say "y" to link the driver statically, or "m" to build a
dynamically linked module called "g_file_storage".
config USB_FILE_STORAGE_TEST
bool "File-backed Storage Gadget testing version"
depends on USB_FILE_STORAGE
default n
help
Say "y" to generate the larger testing version of the
File-backed Storage Gadget, useful for probing the
behavior of USB Mass Storage hosts. Not needed for
normal operation.
config USB_G_SERIAL
tristate "Serial Gadget (with CDC ACM support)"
help
The Serial Gadget talks to the Linux-USB generic serial driver.
This driver supports a CDC-ACM module option, which can be used
to interoperate with MS-Windows hosts or with the Linux-USB
"cdc-acm" driver.
Say "y" to link the driver statically, or "m" to build a
dynamically linked module called "g_serial".
For more information, see Documentation/usb/gadget_serial.txt
which includes instructions and a "driver info file" needed to
make MS-Windows work with this driver.
config USB_MIDI_GADGET
tristate "MIDI Gadget (EXPERIMENTAL)"
depends on SND && EXPERIMENTAL
select SND_RAWMIDI
help
The MIDI Gadget acts as a USB Audio device, with one MIDI
input and one MIDI output. These MIDI jacks appear as
a sound "card" in the ALSA sound system. Other MIDI
connections can then be made on the gadget system, using
ALSA's aconnect utility etc.
Say "y" to link the driver statically, or "m" to build a
dynamically linked module called "g_midi".
config USB_G_PRINTER
tristate "Printer Gadget"
help
The Printer Gadget channels data between the USB host and a
userspace program driving the print engine. The user space
program reads and writes the device file /dev/g_printer to
receive or send printer data. It can use ioctl calls to
the device file to get or set printer status.
Say "y" to link the driver statically, or "m" to build a
dynamically linked module called "g_printer".
For more information, see Documentation/usb/gadget_printer.txt
which includes sample code for accessing the device file.
# put drivers that need isochronous transfer support (for audio
# or video class gadget drivers), or specific hardware, here.
# - none yet
endchoice
endif # USB_GADGET
Reference in New Issue View Git Blame Copy Permalink