58dd7a8d9d
Document DSA tagged and VLAN based switch configuration by showcases. Signed-off-by: Benedikt Spranger <b.spranger@linutronix.de> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
293 lines
7.0 KiB
ReStructuredText
293 lines
7.0 KiB
ReStructuredText
.. SPDX-License-Identifier: GPL-2.0
|
|
|
|
=======================================
|
|
DSA switch configuration from userspace
|
|
=======================================
|
|
|
|
The DSA switch configuration is not integrated into the main userspace
|
|
network configuration suites by now and has to be performed manualy.
|
|
|
|
.. _dsa-config-showcases:
|
|
|
|
Configuration showcases
|
|
-----------------------
|
|
|
|
To configure a DSA switch a couple of commands need to be executed. In this
|
|
documentation some common configuration scenarios are handled as showcases:
|
|
|
|
*single port*
|
|
Every switch port acts as a different configurable Ethernet port
|
|
|
|
*bridge*
|
|
Every switch port is part of one configurable Ethernet bridge
|
|
|
|
*gateway*
|
|
Every switch port except one upstream port is part of a configurable
|
|
Ethernet bridge.
|
|
The upstream port acts as different configurable Ethernet port.
|
|
|
|
All configurations are performed with tools from iproute2, which is available
|
|
at https://www.kernel.org/pub/linux/utils/net/iproute2/
|
|
|
|
Through DSA every port of a switch is handled like a normal linux Ethernet
|
|
interface. The CPU port is the switch port connected to an Ethernet MAC chip.
|
|
The corresponding linux Ethernet interface is called the master interface.
|
|
All other corresponding linux interfaces are called slave interfaces.
|
|
|
|
The slave interfaces depend on the master interface. They can only brought up,
|
|
when the master interface is up.
|
|
|
|
In this documentation the following Ethernet interfaces are used:
|
|
|
|
*eth0*
|
|
the master interface
|
|
|
|
*lan1*
|
|
a slave interface
|
|
|
|
*lan2*
|
|
another slave interface
|
|
|
|
*lan3*
|
|
a third slave interface
|
|
|
|
*wan*
|
|
A slave interface dedicated for upstream traffic
|
|
|
|
Further Ethernet interfaces can be configured similar.
|
|
The configured IPs and networks are:
|
|
|
|
*single port*
|
|
* lan1: 192.0.2.1/30 (192.0.2.0 - 192.0.2.3)
|
|
* lan2: 192.0.2.5/30 (192.0.2.4 - 192.0.2.7)
|
|
* lan3: 192.0.2.9/30 (192.0.2.8 - 192.0.2.11)
|
|
|
|
*bridge*
|
|
* br0: 192.0.2.129/25 (192.0.2.128 - 192.0.2.255)
|
|
|
|
*gateway*
|
|
* br0: 192.0.2.129/25 (192.0.2.128 - 192.0.2.255)
|
|
* wan: 192.0.2.1/30 (192.0.2.0 - 192.0.2.3)
|
|
|
|
.. _dsa-tagged-configuration:
|
|
|
|
Configuration with tagging support
|
|
----------------------------------
|
|
|
|
The tagging based configuration is desired and supported by the majority of
|
|
DSA switches. These switches are capable to tag incoming and outgoing traffic
|
|
without using a VLAN based configuration.
|
|
|
|
single port
|
|
~~~~~~~~~~~
|
|
|
|
.. code-block:: sh
|
|
|
|
# configure each interface
|
|
ip addr add 192.0.2.1/30 dev lan1
|
|
ip addr add 192.0.2.5/30 dev lan2
|
|
ip addr add 192.0.2.9/30 dev lan3
|
|
|
|
# The master interface needs to be brought up before the slave ports.
|
|
ip link set eth0 up
|
|
|
|
# bring up the slave interfaces
|
|
ip link set lan1 up
|
|
ip link set lan2 up
|
|
ip link set lan3 up
|
|
|
|
bridge
|
|
~~~~~~
|
|
|
|
.. code-block:: sh
|
|
|
|
# The master interface needs to be brought up before the slave ports.
|
|
ip link set eth0 up
|
|
|
|
# bring up the slave interfaces
|
|
ip link set lan1 up
|
|
ip link set lan2 up
|
|
ip link set lan3 up
|
|
|
|
# create bridge
|
|
ip link add name br0 type bridge
|
|
|
|
# add ports to bridge
|
|
ip link set dev lan1 master br0
|
|
ip link set dev lan2 master br0
|
|
ip link set dev lan3 master br0
|
|
|
|
# configure the bridge
|
|
ip addr add 192.0.2.129/25 dev br0
|
|
|
|
# bring up the bridge
|
|
ip link set dev br0 up
|
|
|
|
gateway
|
|
~~~~~~~
|
|
|
|
.. code-block:: sh
|
|
|
|
# The master interface needs to be brought up before the slave ports.
|
|
ip link set eth0 up
|
|
|
|
# bring up the slave interfaces
|
|
ip link set wan up
|
|
ip link set lan1 up
|
|
ip link set lan2 up
|
|
|
|
# configure the upstream port
|
|
ip addr add 192.0.2.1/30 dev wan
|
|
|
|
# create bridge
|
|
ip link add name br0 type bridge
|
|
|
|
# add ports to bridge
|
|
ip link set dev lan1 master br0
|
|
ip link set dev lan2 master br0
|
|
|
|
# configure the bridge
|
|
ip addr add 192.0.2.129/25 dev br0
|
|
|
|
# bring up the bridge
|
|
ip link set dev br0 up
|
|
|
|
.. _dsa-vlan-configuration:
|
|
|
|
Configuration without tagging support
|
|
-------------------------------------
|
|
|
|
A minority of switches are not capable to use a taging protocol
|
|
(DSA_TAG_PROTO_NONE). These switches can be configured by a VLAN based
|
|
configuration.
|
|
|
|
single port
|
|
~~~~~~~~~~~
|
|
The configuration can only be set up via VLAN tagging and bridge setup.
|
|
|
|
.. code-block:: sh
|
|
|
|
# tag traffic on CPU port
|
|
ip link add link eth0 name eth0.1 type vlan id 1
|
|
ip link add link eth0 name eth0.2 type vlan id 2
|
|
ip link add link eth0 name eth0.3 type vlan id 3
|
|
|
|
# The master interface needs to be brought up before the slave ports.
|
|
ip link set eth0 up
|
|
ip link set eth0.1 up
|
|
ip link set eth0.2 up
|
|
ip link set eth0.3 up
|
|
|
|
# bring up the slave interfaces
|
|
ip link set lan1 up
|
|
ip link set lan1 up
|
|
ip link set lan3 up
|
|
|
|
# create bridge
|
|
ip link add name br0 type bridge
|
|
|
|
# activate VLAN filtering
|
|
ip link set dev br0 type bridge vlan_filtering 1
|
|
|
|
# add ports to bridges
|
|
ip link set dev lan1 master br0
|
|
ip link set dev lan2 master br0
|
|
ip link set dev lan3 master br0
|
|
|
|
# tag traffic on ports
|
|
bridge vlan add dev lan1 vid 1 pvid untagged
|
|
bridge vlan add dev lan2 vid 2 pvid untagged
|
|
bridge vlan add dev lan3 vid 3 pvid untagged
|
|
|
|
# configure the VLANs
|
|
ip addr add 192.0.2.1/30 dev eth0.1
|
|
ip addr add 192.0.2.5/30 dev eth0.2
|
|
ip addr add 192.0.2.9/30 dev eth0.3
|
|
|
|
# bring up the bridge devices
|
|
ip link set br0 up
|
|
|
|
|
|
bridge
|
|
~~~~~~
|
|
|
|
.. code-block:: sh
|
|
|
|
# tag traffic on CPU port
|
|
ip link add link eth0 name eth0.1 type vlan id 1
|
|
|
|
# The master interface needs to be brought up before the slave ports.
|
|
ip link set eth0 up
|
|
ip link set eth0.1 up
|
|
|
|
# bring up the slave interfaces
|
|
ip link set lan1 up
|
|
ip link set lan2 up
|
|
ip link set lan3 up
|
|
|
|
# create bridge
|
|
ip link add name br0 type bridge
|
|
|
|
# activate VLAN filtering
|
|
ip link set dev br0 type bridge vlan_filtering 1
|
|
|
|
# add ports to bridge
|
|
ip link set dev lan1 master br0
|
|
ip link set dev lan2 master br0
|
|
ip link set dev lan3 master br0
|
|
ip link set eth0.1 master br0
|
|
|
|
# tag traffic on ports
|
|
bridge vlan add dev lan1 vid 1 pvid untagged
|
|
bridge vlan add dev lan2 vid 1 pvid untagged
|
|
bridge vlan add dev lan3 vid 1 pvid untagged
|
|
|
|
# configure the bridge
|
|
ip addr add 192.0.2.129/25 dev br0
|
|
|
|
# bring up the bridge
|
|
ip link set dev br0 up
|
|
|
|
gateway
|
|
~~~~~~~
|
|
|
|
.. code-block:: sh
|
|
|
|
# tag traffic on CPU port
|
|
ip link add link eth0 name eth0.1 type vlan id 1
|
|
ip link add link eth0 name eth0.2 type vlan id 2
|
|
|
|
# The master interface needs to be brought up before the slave ports.
|
|
ip link set eth0 up
|
|
ip link set eth0.1 up
|
|
ip link set eth0.2 up
|
|
|
|
# bring up the slave interfaces
|
|
ip link set wan up
|
|
ip link set lan1 up
|
|
ip link set lan2 up
|
|
|
|
# create bridge
|
|
ip link add name br0 type bridge
|
|
|
|
# activate VLAN filtering
|
|
ip link set dev br0 type bridge vlan_filtering 1
|
|
|
|
# add ports to bridges
|
|
ip link set dev wan master br0
|
|
ip link set eth0.1 master br0
|
|
ip link set dev lan1 master br0
|
|
ip link set dev lan2 master br0
|
|
|
|
# tag traffic on ports
|
|
bridge vlan add dev lan1 vid 1 pvid untagged
|
|
bridge vlan add dev lan2 vid 1 pvid untagged
|
|
bridge vlan add dev wan vid 2 pvid untagged
|
|
|
|
# configure the VLANs
|
|
ip addr add 192.0.2.1/30 dev eth0.2
|
|
ip addr add 192.0.2.129/25 dev br0
|
|
|
|
# bring up the bridge devices
|
|
ip link set br0 up
|