9e60fdcf0c
This adds a new-style I2C driver with basic support for the sixteen bit PCA9539 GPIO expanders. These chips have multiple registers, push-pull output drivers, and (not supported in this patch) pin change interrupts. Board-specific code must provide "pca9539_platform_data" with each chip's "i2c_board_info". That provides the GPIO numbers to be used by that chip, and callbacks for board-specific setup/teardown logic. Derived from drivers/i2c/chips/pca9539.c (which has no current known users). This is faster and simpler; it uses 16-bit register access, and cache the OUTPUT and DIRECTION registers for fast access Signed-off-by: eric miao <eric.miao@marvell.com> Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Acked-by: Jean Delvare <khali@linux-fr.org> Cc: Sam Ravnborg <sam@ravnborg.org> Cc: Haavard Skinnemoen <hskinnemoen@atmel.com> Cc: Philipp Zabel <philipp.zabel@gmail.com> Cc: Russell King <rmk@arm.linux.org.uk> Cc: Ben Gardner <bgardner@wabtec.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
73 lines
2.2 KiB
Plaintext
73 lines
2.2 KiB
Plaintext
#
|
|
# GPIO infrastructure and expanders
|
|
#
|
|
|
|
config HAVE_GPIO_LIB
|
|
bool
|
|
help
|
|
Platforms select gpiolib if they use this infrastructure
|
|
for all their GPIOs, usually starting with ones integrated
|
|
into SOC processors.
|
|
|
|
menu "GPIO Support"
|
|
depends on HAVE_GPIO_LIB
|
|
|
|
config DEBUG_GPIO
|
|
bool "Debug GPIO calls"
|
|
depends on DEBUG_KERNEL
|
|
help
|
|
Say Y here to add some extra checks and diagnostics to GPIO calls.
|
|
The checks help ensure that GPIOs have been properly initialized
|
|
before they are used and that sleeping calls aren not made from
|
|
nonsleeping contexts. They can make bitbanged serial protocols
|
|
slower. The diagnostics help catch the type of setup errors
|
|
that are most common when setting up new platforms or boards.
|
|
|
|
# put expanders in the right section, in alphabetical order
|
|
|
|
comment "I2C GPIO expanders:"
|
|
|
|
config GPIO_PCA9539
|
|
tristate "PCA9539 16-bit I/O port"
|
|
depends on I2C
|
|
help
|
|
Say yes here to support the PCA9539 16-bit I/O port. These
|
|
parts are made by NXP and TI.
|
|
|
|
This driver can also be built as a module. If so, the module
|
|
will be called pca9539.
|
|
|
|
config GPIO_PCF857X
|
|
tristate "PCF857x, PCA857x, and PCA967x I2C GPIO expanders"
|
|
depends on I2C
|
|
help
|
|
Say yes here to provide access to most "quasi-bidirectional" I2C
|
|
GPIO expanders used for additional digital outputs or inputs.
|
|
Most of these parts are from NXP, though TI is a second source for
|
|
some of them. Compatible models include:
|
|
|
|
8 bits: pcf8574, pcf8574a, pca8574, pca8574a,
|
|
pca9670, pca9672, pca9674, pca9674a
|
|
|
|
16 bits: pcf8575, pcf8575c, pca8575,
|
|
pca9671, pca9673, pca9675
|
|
|
|
Your board setup code will need to declare the expanders in
|
|
use, and assign numbers to the GPIOs they expose. Those GPIOs
|
|
can then be used from drivers and other kernel code, just like
|
|
other GPIOs, but only accessible from task contexts.
|
|
|
|
This driver provides an in-kernel interface to those GPIOs using
|
|
platform-neutral GPIO calls.
|
|
|
|
comment "SPI GPIO expanders:"
|
|
|
|
config GPIO_MCP23S08
|
|
tristate "Microchip MCP23S08 I/O expander"
|
|
depends on SPI_MASTER
|
|
help
|
|
SPI driver for Microchip MCP23S08 I/O expander. This provides
|
|
a GPIO interface supporting inputs and outputs.
|
|
|
|
endmenu
|