linux/drivers/usb/host/ehci-pci.c

416 lines
11 KiB
C

/*
* EHCI HCD (Host Controller Driver) PCI Bus Glue.
*
* Copyright (c) 2000-2004 by David Brownell
*
* This program is free software; you can redistribute it and/or modify it
* under the terms of the GNU General Public License as published by the
* Free Software Foundation; either version 2 of the License, or (at your
* option) any later version.
*
* This program is distributed in the hope that it will be useful, but
* WITHOUT ANY WARRANTY; without even the implied warranty of MERCHANTABILITY
* or FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License
* for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software Foundation,
* Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
*/
#ifndef CONFIG_PCI
#error "This file is PCI bus glue. CONFIG_PCI must be defined."
#endif
/*-------------------------------------------------------------------------*/
/* EHCI 0.96 (and later) section 5.1 says how to kick BIOS/SMM/...
* off the controller (maybe it can boot from highspeed USB disks).
*/
static int bios_handoff (struct ehci_hcd *ehci, int where, u32 cap)
{
struct pci_dev *pdev = to_pci_dev(ehci_to_hcd(ehci)->self.controller);
/* always say Linux will own the hardware */
pci_write_config_byte(pdev, where + 3, 1);
/* maybe wait a while for BIOS to respond */
if (cap & (1 << 16)) {
int msec = 5000;
do {
msleep(10);
msec -= 10;
pci_read_config_dword(pdev, where, &cap);
} while ((cap & (1 << 16)) && msec);
if (cap & (1 << 16)) {
ehci_err(ehci, "BIOS handoff failed (%d, %08x)\n",
where, cap);
// some BIOS versions seem buggy...
// return 1;
ehci_warn (ehci, "continuing after BIOS bug...\n");
/* disable all SMIs, and clear "BIOS owns" flag */
pci_write_config_dword(pdev, where + 4, 0);
pci_write_config_byte(pdev, where + 2, 0);
} else
ehci_dbg(ehci, "BIOS handoff succeeded\n");
}
return 0;
}
/* called by khubd or root hub init threads */
static int ehci_pci_reset (struct usb_hcd *hcd)
{
struct ehci_hcd *ehci = hcd_to_ehci (hcd);
u32 temp;
unsigned count = 256/4;
spin_lock_init (&ehci->lock);
ehci->caps = hcd->regs;
ehci->regs = hcd->regs + HC_LENGTH (readl (&ehci->caps->hc_capbase));
dbg_hcs_params (ehci, "reset");
dbg_hcc_params (ehci, "reset");
/* cache this readonly data; minimize chip reads */
ehci->hcs_params = readl (&ehci->caps->hcs_params);
if (hcd->self.controller->bus == &pci_bus_type) {
struct pci_dev *pdev = to_pci_dev(hcd->self.controller);
switch (pdev->vendor) {
case PCI_VENDOR_ID_TDI:
if (pdev->device == PCI_DEVICE_ID_TDI_EHCI) {
ehci->is_tdi_rh_tt = 1;
tdi_reset (ehci);
}
break;
case PCI_VENDOR_ID_AMD:
/* AMD8111 EHCI doesn't work, according to AMD errata */
if (pdev->device == 0x7463) {
ehci_info (ehci, "ignoring AMD8111 (errata)\n");
return -EIO;
}
break;
case PCI_VENDOR_ID_NVIDIA:
/* NVidia reports that certain chips don't handle
* QH, ITD, or SITD addresses above 2GB. (But TD,
* data buffer, and periodic schedule are normal.)
*/
switch (pdev->device) {
case 0x003c: /* MCP04 */
case 0x005b: /* CK804 */
case 0x00d8: /* CK8 */
case 0x00e8: /* CK8S */
if (pci_set_consistent_dma_mask(pdev,
DMA_31BIT_MASK) < 0)
ehci_warn (ehci, "can't enable NVidia "
"workaround for >2GB RAM\n");
break;
}
break;
}
/* optional debug port, normally in the first BAR */
temp = pci_find_capability (pdev, 0x0a);
if (temp) {
pci_read_config_dword(pdev, temp, &temp);
temp >>= 16;
if ((temp & (3 << 13)) == (1 << 13)) {
temp &= 0x1fff;
ehci->debug = hcd->regs + temp;
temp = readl (&ehci->debug->control);
ehci_info (ehci, "debug port %d%s\n",
HCS_DEBUG_PORT(ehci->hcs_params),
(temp & DBGP_ENABLED)
? " IN USE"
: "");
if (!(temp & DBGP_ENABLED))
ehci->debug = NULL;
}
}
temp = HCC_EXT_CAPS (readl (&ehci->caps->hcc_params));
} else
temp = 0;
/* EHCI 0.96 and later may have "extended capabilities" */
while (temp && count--) {
u32 cap;
pci_read_config_dword (to_pci_dev(hcd->self.controller),
temp, &cap);
ehci_dbg (ehci, "capability %04x at %02x\n", cap, temp);
switch (cap & 0xff) {
case 1: /* BIOS/SMM/... handoff */
if (bios_handoff (ehci, temp, cap) != 0)
return -EOPNOTSUPP;
break;
case 0: /* illegal reserved capability */
ehci_warn (ehci, "illegal capability!\n");
cap = 0;
/* FALLTHROUGH */
default: /* unknown */
break;
}
temp = (cap >> 8) & 0xff;
}
if (!count) {
ehci_err (ehci, "bogus capabilities ... PCI problems!\n");
return -EIO;
}
if (ehci_is_TDI(ehci))
ehci_reset (ehci);
ehci_port_power (ehci, 0);
/* at least the Genesys GL880S needs fixup here */
temp = HCS_N_CC(ehci->hcs_params) * HCS_N_PCC(ehci->hcs_params);
temp &= 0x0f;
if (temp && HCS_N_PORTS(ehci->hcs_params) > temp) {
ehci_dbg (ehci, "bogus port configuration: "
"cc=%d x pcc=%d < ports=%d\n",
HCS_N_CC(ehci->hcs_params),
HCS_N_PCC(ehci->hcs_params),
HCS_N_PORTS(ehci->hcs_params));
if (hcd->self.controller->bus == &pci_bus_type) {
struct pci_dev *pdev;
pdev = to_pci_dev(hcd->self.controller);
switch (pdev->vendor) {
case 0x17a0: /* GENESYS */
/* GL880S: should be PORTS=2 */
temp |= (ehci->hcs_params & ~0xf);
ehci->hcs_params = temp;
break;
case PCI_VENDOR_ID_NVIDIA:
/* NF4: should be PCC=10 */
break;
}
}
}
/* force HC to halt state */
return ehci_halt (ehci);
}
static int ehci_pci_start (struct usb_hcd *hcd)
{
struct ehci_hcd *ehci = hcd_to_ehci (hcd);
int result = 0;
if (hcd->self.controller->bus == &pci_bus_type) {
struct pci_dev *pdev;
u16 port_wake;
pdev = to_pci_dev(hcd->self.controller);
/* Serial Bus Release Number is at PCI 0x60 offset */
pci_read_config_byte(pdev, 0x60, &ehci->sbrn);
/* port wake capability, reported by boot firmware */
pci_read_config_word(pdev, 0x62, &port_wake);
hcd->can_wakeup = (port_wake & 1) != 0;
/* help hc dma work well with cachelines */
result = pci_set_mwi(pdev);
if (result)
ehci_dbg(ehci, "unable to enable MWI - not fatal.\n");
}
return ehci_run (hcd);
}
/* always called by thread; normally rmmod */
static void ehci_pci_stop (struct usb_hcd *hcd)
{
ehci_stop (hcd);
}
/*-------------------------------------------------------------------------*/
#ifdef CONFIG_PM
/* suspend/resume, section 4.3 */
/* These routines rely on the bus (pci, platform, etc)
* to handle powerdown and wakeup, and currently also on
* transceivers that don't need any software attention to set up
* the right sort of wakeup.
*/
static int ehci_pci_suspend (struct usb_hcd *hcd, pm_message_t message)
{
struct ehci_hcd *ehci = hcd_to_ehci (hcd);
if (time_before (jiffies, ehci->next_statechange))
msleep (100);
#ifdef CONFIG_USB_SUSPEND
(void) usb_suspend_device (hcd->self.root_hub);
#else
usb_lock_device (hcd->self.root_hub);
(void) ehci_bus_suspend (hcd);
usb_unlock_device (hcd->self.root_hub);
#endif
// save (PCI) FLADJ in case of Vaux power loss
// ... we'd only use it to handle clock skew
return 0;
}
static int ehci_pci_resume (struct usb_hcd *hcd)
{
struct ehci_hcd *ehci = hcd_to_ehci (hcd);
unsigned port;
struct usb_device *root = hcd->self.root_hub;
int retval = -EINVAL;
// maybe restore (PCI) FLADJ
if (time_before (jiffies, ehci->next_statechange))
msleep (100);
/* If any port is suspended (or owned by the companion),
* we know we can/must resume the HC (and mustn't reset it).
*/
for (port = HCS_N_PORTS (ehci->hcs_params); port > 0; ) {
u32 status;
port--;
status = readl (&ehci->regs->port_status [port]);
if (!(status & PORT_POWER))
continue;
if (status & (PORT_SUSPEND | PORT_OWNER)) {
down (&hcd->self.root_hub->serialize);
retval = ehci_bus_resume (hcd);
up (&hcd->self.root_hub->serialize);
break;
}
if (!root->children [port])
continue;
dbg_port (ehci, __FUNCTION__, port + 1, status);
usb_set_device_state (root->children[port],
USB_STATE_NOTATTACHED);
}
/* Else reset, to cope with power loss or flush-to-storage
* style "resume" having activated BIOS during reboot.
*/
if (port == 0) {
(void) ehci_halt (ehci);
(void) ehci_reset (ehci);
(void) ehci_pci_reset (hcd);
/* emptying the schedule aborts any urbs */
spin_lock_irq (&ehci->lock);
if (ehci->reclaim)
ehci->reclaim_ready = 1;
ehci_work (ehci, NULL);
spin_unlock_irq (&ehci->lock);
/* restart; khubd will disconnect devices */
retval = ehci_run (hcd);
/* here we "know" root ports should always stay powered;
* but some controllers may lose all power.
*/
ehci_port_power (ehci, 1);
}
return retval;
}
#endif
static const struct hc_driver ehci_pci_hc_driver = {
.description = hcd_name,
.product_desc = "EHCI Host Controller",
.hcd_priv_size = sizeof(struct ehci_hcd),
/*
* generic hardware linkage
*/
.irq = ehci_irq,
.flags = HCD_MEMORY | HCD_USB2,
/*
* basic lifecycle operations
*/
.reset = ehci_pci_reset,
.start = ehci_pci_start,
#ifdef CONFIG_PM
.suspend = ehci_pci_suspend,
.resume = ehci_pci_resume,
#endif
.stop = ehci_pci_stop,
/*
* managing i/o requests and associated device resources
*/
.urb_enqueue = ehci_urb_enqueue,
.urb_dequeue = ehci_urb_dequeue,
.endpoint_disable = ehci_endpoint_disable,
/*
* scheduling support
*/
.get_frame_number = ehci_get_frame,
/*
* root hub support
*/
.hub_status_data = ehci_hub_status_data,
.hub_control = ehci_hub_control,
.bus_suspend = ehci_bus_suspend,
.bus_resume = ehci_bus_resume,
};
/*-------------------------------------------------------------------------*/
/* PCI driver selection metadata; PCI hotplugging uses this */
static const struct pci_device_id pci_ids [] = { {
/* handle any USB 2.0 EHCI controller */
PCI_DEVICE_CLASS(((PCI_CLASS_SERIAL_USB << 8) | 0x20), ~0),
.driver_data = (unsigned long) &ehci_pci_hc_driver,
},
{ /* end: all zeroes */ }
};
MODULE_DEVICE_TABLE (pci, pci_ids);
/* pci driver glue; this is a "new style" PCI driver module */
static struct pci_driver ehci_pci_driver = {
.name = (char *) hcd_name,
.id_table = pci_ids,
.owner = THIS_MODULE,
.probe = usb_hcd_pci_probe,
.remove = usb_hcd_pci_remove,
#ifdef CONFIG_PM
.suspend = usb_hcd_pci_suspend,
.resume = usb_hcd_pci_resume,
#endif
};
static int __init ehci_hcd_pci_init (void)
{
if (usb_disabled())
return -ENODEV;
pr_debug ("%s: block sizes: qh %Zd qtd %Zd itd %Zd sitd %Zd\n",
hcd_name,
sizeof (struct ehci_qh), sizeof (struct ehci_qtd),
sizeof (struct ehci_itd), sizeof (struct ehci_sitd));
return pci_register_driver (&ehci_pci_driver);
}
module_init (ehci_hcd_pci_init);
static void __exit ehci_hcd_pci_cleanup (void)
{
pci_unregister_driver (&ehci_pci_driver);
}
module_exit (ehci_hcd_pci_cleanup);