abf0c1bc94
Board is a carrier board for Stamp9G20, with additional peripherals for a building automation system Signed-off-by: Peter Gsellmann <pgsellmann@portner-elektronik.at> [nicolas.ferre@atmel.com: remove machine_desc.io_pg_offst and .phys_io] Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
323 lines
7.4 KiB
C
323 lines
7.4 KiB
C
/*
|
|
* Copyright (C) 2010 Christian Glindkamp <christian.glindkamp@taskit.de>
|
|
* taskit GmbH
|
|
*
|
|
* This program is free software; you can redistribute it and/or modify
|
|
* it under the terms of the GNU General Public License as published by
|
|
* the Free Software Foundation; either version 2 of the License, or
|
|
* (at your option) any later version.
|
|
*
|
|
* This program is distributed in the hope that it will be useful,
|
|
* but WITHOUT ANY WARRANTY; without even the implied warranty of
|
|
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
|
|
* GNU General Public License for more details.
|
|
*
|
|
* You should have received a copy of the GNU General Public License
|
|
* along with this program; if not, write to the Free Software
|
|
* Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
|
|
*/
|
|
/*
|
|
* copied and adjusted from board-stamp9g20.c
|
|
* by Peter Gsellmann <pgsellmann@portner-elektronik.at>
|
|
*/
|
|
|
|
#include <linux/mm.h>
|
|
#include <linux/platform_device.h>
|
|
#include <linux/gpio.h>
|
|
#include <linux/w1-gpio.h>
|
|
|
|
#include <asm/mach-types.h>
|
|
#include <asm/mach/arch.h>
|
|
|
|
#include <mach/board.h>
|
|
#include <mach/at91sam9_smc.h>
|
|
|
|
#include "sam9_smc.h"
|
|
#include "generic.h"
|
|
|
|
|
|
static void __init pcontrol_g20_map_io(void)
|
|
{
|
|
/* Initialize processor: 18.432 MHz crystal */
|
|
at91sam9260_initialize(18432000);
|
|
|
|
/* DGBU on ttyS0. (Rx, Tx) only TTL -> JTAG connector X7 17,19 ) */
|
|
at91_register_uart(0, 0, 0);
|
|
|
|
/* USART0 on ttyS1. (Rx, Tx, CTS, RTS) piggyback A2 */
|
|
at91_register_uart(AT91SAM9260_ID_US0, 1, ATMEL_UART_CTS
|
|
| ATMEL_UART_RTS);
|
|
|
|
/* USART1 on ttyS2. (Rx, Tx, CTS, RTS) isolated RS485 X5 */
|
|
at91_register_uart(AT91SAM9260_ID_US1, 2, ATMEL_UART_CTS
|
|
| ATMEL_UART_RTS);
|
|
|
|
/* USART2 on ttyS3. (Rx, Tx) 9bit-Bus Multidrop-mode X4 */
|
|
at91_register_uart(AT91SAM9260_ID_US4, 3, 0);
|
|
|
|
/* set serial console to ttyS0 (ie, DBGU) */
|
|
at91_set_serial_console(0);
|
|
}
|
|
|
|
|
|
static void __init init_irq(void)
|
|
{
|
|
at91sam9260_init_interrupts(NULL);
|
|
}
|
|
|
|
|
|
/*
|
|
* NAND flash 512MiB 1,8V 8-bit, sector size 128 KiB
|
|
*/
|
|
static struct atmel_nand_data __initdata nand_data = {
|
|
.ale = 21,
|
|
.cle = 22,
|
|
.rdy_pin = AT91_PIN_PC13,
|
|
.enable_pin = AT91_PIN_PC14,
|
|
};
|
|
|
|
/*
|
|
* Bus timings; unit = 7.57ns
|
|
*/
|
|
static struct sam9_smc_config __initdata nand_smc_config = {
|
|
.ncs_read_setup = 0,
|
|
.nrd_setup = 2,
|
|
.ncs_write_setup = 0,
|
|
.nwe_setup = 2,
|
|
|
|
.ncs_read_pulse = 4,
|
|
.nrd_pulse = 4,
|
|
.ncs_write_pulse = 4,
|
|
.nwe_pulse = 4,
|
|
|
|
.read_cycle = 7,
|
|
.write_cycle = 7,
|
|
|
|
.mode = AT91_SMC_READMODE | AT91_SMC_WRITEMODE
|
|
| AT91_SMC_EXNWMODE_DISABLE | AT91_SMC_DBW_8,
|
|
.tdf_cycles = 3,
|
|
};
|
|
|
|
static struct sam9_smc_config __initdata pcontrol_smc_config[2] = { {
|
|
.ncs_read_setup = 16,
|
|
.nrd_setup = 18,
|
|
.ncs_write_setup = 16,
|
|
.nwe_setup = 18,
|
|
|
|
.ncs_read_pulse = 63,
|
|
.nrd_pulse = 55,
|
|
.ncs_write_pulse = 63,
|
|
.nwe_pulse = 55,
|
|
|
|
.read_cycle = 127,
|
|
.write_cycle = 127,
|
|
|
|
.mode = AT91_SMC_READMODE | AT91_SMC_WRITEMODE
|
|
| AT91_SMC_EXNWMODE_DISABLE | AT91_SMC_BAT_SELECT
|
|
| AT91_SMC_DBW_8 | AT91_SMC_PS_4
|
|
| AT91_SMC_TDFMODE,
|
|
.tdf_cycles = 3,
|
|
}, {
|
|
.ncs_read_setup = 0,
|
|
.nrd_setup = 0,
|
|
.ncs_write_setup = 0,
|
|
.nwe_setup = 1,
|
|
|
|
.ncs_read_pulse = 8,
|
|
.nrd_pulse = 8,
|
|
.ncs_write_pulse = 5,
|
|
.nwe_pulse = 4,
|
|
|
|
.read_cycle = 8,
|
|
.write_cycle = 7,
|
|
|
|
.mode = AT91_SMC_READMODE | AT91_SMC_WRITEMODE
|
|
| AT91_SMC_EXNWMODE_DISABLE | AT91_SMC_BAT_SELECT
|
|
| AT91_SMC_DBW_16 | AT91_SMC_PS_8
|
|
| AT91_SMC_TDFMODE,
|
|
.tdf_cycles = 1,
|
|
} };
|
|
|
|
static void __init add_device_nand(void)
|
|
{
|
|
/* configure chip-select 3 (NAND) */
|
|
sam9_smc_configure(3, &nand_smc_config);
|
|
at91_add_device_nand(&nand_data);
|
|
}
|
|
|
|
|
|
static void __init add_device_pcontrol(void)
|
|
{
|
|
/* configure chip-select 4 (IO compatible to 8051 X4 ) */
|
|
sam9_smc_configure(4, &pcontrol_smc_config[0]);
|
|
/* configure chip-select 7 (FerroRAM 256KiBx16bit MR2A16A D4 ) */
|
|
sam9_smc_configure(7, &pcontrol_smc_config[1]);
|
|
}
|
|
|
|
|
|
/*
|
|
* MCI (SD/MMC)
|
|
* det_pin, wp_pin and vcc_pin are not connected
|
|
*/
|
|
#if defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_ATMELMCI_MODULE)
|
|
static struct mci_platform_data __initdata mmc_data = {
|
|
.slot[0] = {
|
|
.bus_width = 4,
|
|
},
|
|
};
|
|
#else
|
|
static struct at91_mmc_data __initdata mmc_data = {
|
|
.wire4 = 1,
|
|
};
|
|
#endif
|
|
|
|
|
|
/*
|
|
* USB Host port
|
|
*/
|
|
static struct at91_usbh_data __initdata usbh_data = {
|
|
.ports = 2,
|
|
};
|
|
|
|
|
|
/*
|
|
* USB Device port
|
|
*/
|
|
static struct at91_udc_data __initdata pcontrol_g20_udc_data = {
|
|
.vbus_pin = AT91_PIN_PA22, /* Detect +5V bus voltage */
|
|
.pullup_pin = AT91_PIN_PA4, /* K-state, active low */
|
|
};
|
|
|
|
|
|
/*
|
|
* MACB Ethernet device
|
|
*/
|
|
static struct at91_eth_data __initdata macb_data = {
|
|
.phy_irq_pin = AT91_PIN_PA28,
|
|
.is_rmii = 1,
|
|
};
|
|
|
|
|
|
/*
|
|
* I2C devices: eeprom and phy/switch
|
|
*/
|
|
static struct i2c_board_info __initdata pcontrol_g20_i2c_devices[] = {
|
|
{ /* D7 address width=2, 8KiB */
|
|
I2C_BOARD_INFO("24c64", 0x50)
|
|
}, { /* D8 address width=1, 1 byte has 32 bits! */
|
|
I2C_BOARD_INFO("lan9303", 0x0a)
|
|
}, };
|
|
|
|
|
|
/*
|
|
* LEDs
|
|
*/
|
|
static struct gpio_led pcontrol_g20_leds[] = {
|
|
{
|
|
.name = "LED1", /* red H5 */
|
|
.gpio = AT91_PIN_PB18,
|
|
.active_low = 1,
|
|
.default_trigger = "none", /* supervisor */
|
|
}, {
|
|
.name = "LED2", /* yellow H7 */
|
|
.gpio = AT91_PIN_PB19,
|
|
.active_low = 1,
|
|
.default_trigger = "mmc0", /* SD-card activity */
|
|
}, {
|
|
.name = "LED3", /* green H2 */
|
|
.gpio = AT91_PIN_PB20,
|
|
.active_low = 1,
|
|
.default_trigger = "heartbeat", /* blinky */
|
|
}, {
|
|
.name = "LED4", /* red H3 */
|
|
.gpio = AT91_PIN_PC6,
|
|
.active_low = 1,
|
|
.default_trigger = "none", /* connection lost */
|
|
}, {
|
|
.name = "LED5", /* yellow H6 */
|
|
.gpio = AT91_PIN_PC7,
|
|
.active_low = 1,
|
|
.default_trigger = "none", /* unsent data */
|
|
}, {
|
|
.name = "LED6", /* green H1 */
|
|
.gpio = AT91_PIN_PC9,
|
|
.active_low = 1,
|
|
.default_trigger = "none", /* snafu */
|
|
}
|
|
};
|
|
|
|
|
|
/*
|
|
* SPI devices
|
|
*/
|
|
static struct spi_board_info pcontrol_g20_spi_devices[] = {
|
|
{
|
|
.modalias = "spidev", /* HMI port X4 */
|
|
.chip_select = 1,
|
|
.max_speed_hz = 50 * 1000 * 1000,
|
|
.bus_num = 0,
|
|
}, {
|
|
.modalias = "spidev", /* piggyback A2 */
|
|
.chip_select = 0,
|
|
.max_speed_hz = 50 * 1000 * 1000,
|
|
.bus_num = 1,
|
|
},
|
|
};
|
|
|
|
|
|
/*
|
|
* Dallas 1-Wire DS2431
|
|
*/
|
|
static struct w1_gpio_platform_data w1_gpio_pdata = {
|
|
.pin = AT91_PIN_PA29,
|
|
.is_open_drain = 1,
|
|
};
|
|
|
|
static struct platform_device w1_device = {
|
|
.name = "w1-gpio",
|
|
.id = -1,
|
|
.dev.platform_data = &w1_gpio_pdata,
|
|
};
|
|
|
|
static void add_wire1(void)
|
|
{
|
|
at91_set_GPIO_periph(w1_gpio_pdata.pin, 1);
|
|
at91_set_multi_drive(w1_gpio_pdata.pin, 1);
|
|
platform_device_register(&w1_device);
|
|
}
|
|
|
|
|
|
static void __init pcontrol_g20_board_init(void)
|
|
{
|
|
at91_add_device_serial();
|
|
add_device_nand();
|
|
#if defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_ATMELMCI_MODULE)
|
|
at91_add_device_mci(0, &mmc_data);
|
|
#else
|
|
at91_add_device_mmc(0, &mmc_data);
|
|
#endif
|
|
at91_add_device_usbh(&usbh_data);
|
|
at91_add_device_eth(&macb_data);
|
|
at91_add_device_i2c(pcontrol_g20_i2c_devices,
|
|
ARRAY_SIZE(pcontrol_g20_i2c_devices));
|
|
add_wire1();
|
|
add_device_pcontrol();
|
|
at91_add_device_spi(pcontrol_g20_spi_devices,
|
|
ARRAY_SIZE(pcontrol_g20_spi_devices));
|
|
at91_add_device_udc(&pcontrol_g20_udc_data);
|
|
at91_gpio_leds(pcontrol_g20_leds,
|
|
ARRAY_SIZE(pcontrol_g20_leds));
|
|
/* piggyback A2 */
|
|
at91_set_gpio_output(AT91_PIN_PB31, 1);
|
|
}
|
|
|
|
|
|
MACHINE_START(PCONTROL_G20, "PControl G20")
|
|
/* Maintainer: pgsellmann@portner-elektronik.at */
|
|
.boot_params = AT91_SDRAM_BASE + 0x100,
|
|
.timer = &at91sam926x_timer,
|
|
.map_io = pcontrol_g20_map_io,
|
|
.init_irq = init_irq,
|
|
.init_machine = pcontrol_g20_board_init,
|
|
MACHINE_END
|